Hierarchically Patterned Self-Cleaning Polymer Composites for Daytime Radiative Cooling.

Passive daytime radiative cooling (PDRC) has the potential to reduce energy demand and mitigate global warming. However, surface contamination from dust and bacterial buildup limits practical PDRC applications. Here, we develop a hierarchically patterned nanoporous composite (HPNC) using a facile template-molding fabrication method to integrate PDRC materials with self-cleaning and antibacterial functions. The HPNC design decouples multifunctional control into different characteristic length scales that can be optimized simultaneously. The nanoporous polymer matrix embedded with tunable fillers enables 7.8 and 4.4 °C temperature reduction for outdoor personal and building cooling, respectively, under intense solar irradiance. Meanwhile, a microscale pillar array pattern integrated into the HPNC enables superhydrophobicity with self-cleaning and antisoiling functions to mitigate surface contamination. Moreover, the surface coating of photocatalytic agents can generate photoinduced antibacterial effects. The scalable fabrication and multifunctional capabilities of our HPNC design offer a promising solution for practical PDRC applications with minimal maintenance needs.

Dissolvable Template Nanoimprint Lithography: A Facile and Versatile Nanoscale Replication Technique.

Nanoimprinting lithography (NIL) is a next-generation nanofabrication method, capable of replicating nanostructures from original master surfaces. Here, we develop highly scalable, simple, and nondestructive NIL using a dissolvable template. Termed dissolvable template nanoimprinting lithography (DT-NIL), our method utilizes an economic thermoplastic resin to fabricate nanoimprinting templates, which can be easily dissolved in simple organic solvents. We used the DT-NIL method to replicate cicada wings which have surface nanofeatures of ∼100 nm in height. The master, template, and replica surfaces showed a >∼94% similarity based on the measured diameter and height of the nanofeatures. The versatility of DT-NIL was also demonstrated with the replication of re-entrant, multiscale, and hierarchical features on fly wings, as well as hard silicon wafer-based artificial nanostructures. The DT-NIL method can be performed under ambient conditions with inexpensive materials and equipment. Our work opens the door to opportunities for economical and high-throughput nanofabrication processes.

Spatially resolved chemical analysis of cicada wings using laser-ablation electrospray ionization (LAESI) imaging mass spectrometry (IMS).

Laser-ablation electrospray ionization (LAESI) imaging mass spectrometry (IMS) is an emerging bioanalytical tool for direct imaging and analysis of biological tissues. Performing ionization in an ambient environment, this technique requires little sample preparation and no additional matrix, and can be performed on natural, uneven surfaces. When combined with optical microscopy, the investigation of biological samples by LAESI allows for spatially resolved compositional analysis. We demonstrate here the applicability of LAESI-IMS for the chemical analysis of thin, desiccated biological samples, specifically Neotibicen pruinosus cicada wings. Positive-ion LAESI-IMS accurate ion-map data was acquired from several wing cells and superimposed onto optical images allowing for compositional comparisons across areas of the wing. Various putative chemical identifications were made indicating the presence of hydrocarbons, lipids/esters, amines/amides, and sulfonated/phosphorylated compounds. With the spatial resolution capability, surprising chemical distribution patterns were observed across the cicada wing, which may assist in correlating trends in surface properties with chemical distribution. Observed ions were either (1) equally dispersed across the wing, (2) more concentrated closer to the body of the insect (proximal end), or (3) more concentrated toward the tip of the wing (distal end). These findings demonstrate LAESI-IMS as a tool for the acquisition of spatially resolved chemical information from fragile, dried insect wings. This LAESI-IMS technique has important implications for the study of functional biomaterials, where understanding the correlation between chemical composition, physical structure, and biological function is critical. Graphical abstract Positive-ion laser-ablation electrospray ionization mass spectrometry coupled with optical imaging provides a powerful tool for the spatially resolved chemical analysis of cicada wings.

Perchlorate reduction using free and encapsulated Azospira oryzae enzymes.

Existing methods for perchlorate remediation are hampered by the common co-occurrence of nitrate, which is structurally similar and a preferred electron acceptor. In this work, the potential for perchlorate removal using cell-free bacterial enzymes as biocatalysts was investigated using crude cell lysates and soluble protein fractions of Azospira oryzae PS, as well as soluble protein fractions encapsulated in lipid and polymer vesicles. The crude lysates showed activities between 41 700 to 54 400 U L(-1) (2.49 to 3.06 U mg(-1) total protein). Soluble protein fractions had activities of 15 400 to 29 900 U L(-1) (1.70 to 1.97 U mg(-1)) and still retained an average of 58.2% of their original activity after 23 days of storage at 4 °C under aerobic conditions. Perchlorate was removed by the soluble protein fraction at higher rates than nitrate. Importantly, perchlorate reduction occurred even in the presence of 500-fold excess nitrate. The soluble protein fraction retained its function after encapsulation in lipid or polymer vesicles, with activities of 13.8 to 70.7 U L(-1), in agreement with theoretical calculations accounting for the volume limitation of the vesicles. Further, encapsulation mitigated enzyme inactivation by proteinase K. Enzyme-based technologies could prove effective at perchlorate removal from water cocontaminated with nitrate or sulfate.

Pilot scale microbial fuel cells using air cathodes for producing electricity while treating wastewater.

Microbial fuel cells (MFCs) can generate electrical energy from the oxidation of the organic matter, but they must be demonstrated at large scales, treat real wastewaters, and show the required performance needed at a site to provide a path forward for this technology. Previous pilot-scale studies of MFC technology have relied on systems with aerated catholytes, which limited energy recovery due to the energy consumed by pumping air into the catholyte. In the present study, we developed, deployed, and tested an 850 L (1400 L total liquid volume) air-cathode MFC treating domestic-type wastewater at a centralized wastewater treatment facility. The wastewater was processed over a hydraulic retention time (HRT) of 12 h through a sequence of 17 brush anode modules (11 m2 total projected anode area) and 16 cathode modules, each constructed using two air-cathodes (0.6 m2 each, total cathode area of 20 m2) with the air side facing each other to allow passive air flow. The MFC effluent was further treated in a biofilter (BF) to decrease the organic matter content. The field test was conducted for over six months to fully characterize the electrochemical and wastewater treatment performance. Wastewater quality as well as electrical energy production were routinely monitored. The power produced over six months by the MFC averaged 0.46 ± 0.35 W (0.043 W m-2 normalized to the cross-sectional area of an anode) at a current of 1.54 ± 0.90 A with a coulombic efficiency of 9%. Approximately 49 ± 15 % of the chemical oxygen demand (COD) was removed in the MFC alone as well as a large amount of the biochemical oxygen demand (BOD5) (70%) and total suspended solid (TSS) (48%). In the combined MFC/BF process, up to 91 ± 6 % of the COD and 91 % of the BOD5 were removed as well as certain bacteria (E. coli, 98.9%; fecal coliforms, 99.1%). The average effluent concentration of nitrate was 1.6 ± 2.4 mg L-1, nitrite was 0.17 ± 0.24 mg L-1 and ammonia was 0.4 ± 1.0 mg L-1. The pilot scale reactor presented here is the largest air-cathode MFC ever tested, generating electrical power while treating wastewater.

Particulate-Droplet Coalescence and Self-Transport on Superhydrophobic Surfaces.

Particulate transport from surfaces governs a variety of phenomena including fungal spore dispersal, bioaerosol transmission, and self-cleaning. Here, we report a previously unidentified mechanism governing passive particulate removal from superhydrophobic surfaces, where a particle coalescing with a water droplet (∼10 to ∼100 µm) spontaneously launches. Compared to previously discovered coalescence-induced binary droplet jumping, the reported mechanism represents a more general capillary-inertial dominated transport mode coupled with particle/droplet properties and is typically mediated by rotation in addition to translation. Through wetting and momentum analyses, we show that transport physics depends on particle/droplet density, size, and wettability. The observed mechanism presents a simple and passive pathway to achieve self-cleaning on both artificial as well as biological materials as confirmed here with experiments conducted on butterfly wings, cicada wings, and clover leaves. Our findings provide insights into particle-droplet interaction and spontaneous particulate transport, which may facilitate the development of functional surfaces for medical, optical, thermal, and energy applications.

Poly(dimethylsiloxane) cross-linked carbon paste electrodes for microfluidic electrochemical sensing.

Recently, the development of electrochemical biosensors as part of microfluidic devices has garnered a great deal of attention because of the small instrument size and portability afforded by the integration of electrochemistry in microfluidic systems. Electrode fabrication, however, has proven to be a major obstacle in the field. Here, an alternative method to create integrated, low cost, robust, patternable carbon paste electrodes (CPEs) for microfluidic devices is presented. The new CPEs are composed of graphite powder and a binder consisting of a mixture of poly(dimethylsiloxane) (PDMS) and mineral oil. The electrodes are made by filling channels molded in previously cross-linked PDMS using a method analogous to screen printing. The optimal binder composition was investigated to obtain electrodes that were physically robust and performed well electrochemically. After studying the basic electrochemistry, the PDMS-oil CPEs were modified with multi-walled carbon nanotubes (MWCNT) and cobalt phthalocyanine (CoPC) for the detection of catecholamines and thiols, respectively, to demonstrate the ease of electrode chemical modification. Significant improvement of analyte signal detection was observed from both types of modified CPEs. A nearly 2-fold improvement in the electrochemical signal for 100 µM dithiothreitol (DTT) was observed when using a CoPC modified electrode (4.0 ± 0.2 nA (n = 3) versus 2.5 ± 0.2 nA (n = 3)). The improvement in signal was even more pronounced when looking at catecholamines, namely dopamine, using MWCNT modified CPEs. In this case, an order of magnitude improvement in limit of detection was observed for dopamine when using the MWCNT modified CPEs (50 nM versus 500 nM). CoPC modified CPEs were successfully used to detect thiols in red blood cell lysate while MWCNT modified CPEs were used to monitor temporal changes in catecholamine release from PC12 cells following stimulation with potassium.

Culturing and investigation of stress-induced lipid accumulation in microalgae using a microfluidic device.

There is increasing interest in using microalgae as a lipid feedstock for the production of biofuels. Lipids used for these purposes are triacylglycerols that can be converted to fatty acid methyl esters (biodiesel) or decarboxylated to "green diesel." Lipid accumulation in most microalgal species is dependent on environmental stress and culturing conditions, and these conditions are currently optimized using slow, labor-intensive screening processes. Increasing the screening throughput would help reduce the development cost and time to commercial production. Here, we demonstrated an initial step towards this goal in the development of a glass/poly(dimethylsiloxane) (PDMS) microfluidic device capable of screening microalgal culturing and stress conditions. The device contained power-free valves to isolate microalgae in a microfluidic growth chamber for culturing and stress experiments. Initial experiments involved determining the biocompatibility and culturing capability of the device using the microalga Tetraselmis chuii. With this device, T. chuii could be successfully cultured for up to 3 weeks on-chip. Following these experiments, the device was used to investigate lipid accumulation in the microalga Neochloris oleabundans. It was shown that this microalga could be stressed to accumulate cytosolic lipids in a microfluidic environment, as evidenced with fluorescence lipid staining. This work represents the first example of microalgal culturing in a microfluidic device and signifies an important expansion of microfluidics into the biofuels research arena.

Solid-phase microextraction (SPME) for determination of geosmin and 2-methylisoborneol in volatile emissions from soil disturbance.

A method is described here for the concentration and determination of geosmin and 2-methylisoborneol (2-MIB) from the gaseous phase, with translation to field collection and quantification from soil disturbances in situ. The method is based on the use of solid-phase microextraction (SPME) fibers for adsorption of volatile chemicals from the vapor phase, followed by desorption into a gas chromatograph-mass spectrometer (GC-MS) for analysis. The use of a SPME fiber allows simple introduction to the GC-MS without further sample preparation. Several fiber sorbent types were studied and the 50/30 µm DVB/CAR/PDMS was the best performer to maximize the detected peak areas of both analytes combined. Factors such as extraction temperature and time along with desorption temperature and time were explored with respect to analyte recovery. An extraction temperature of 30 °C for 10 min, with a desorption temperature of 230 °C for 4 min was best for the simultaneous analysis of both geosmin and 2-MIB without complete loss of either one. The developed method was used successfully to measure geosmin and 2-MIB emission from just above disturbed and undisturbed soils, indicating that this method detects both compounds readily from atmospheric samples. Both geosmin and 2-MIB were present as background concentrations in the open air, while disturbed soils emitted much higher concentrations of both compounds. Surprisingly, 2-MIB was always detected at higher concentrations than geosmin, indicating that a focus on its detection may be more useful for soil emission monitoring and more sensitive to low levels of soil disturbance.

Electrokinetic control of fluid transport in gold-coated nanocapillary array membranes in hybrid nanofluidic-microfluidic devices.

The introduction of metallic elements into microfluidic devices that support electrokinetic transport creates several fundamental issues relative to the high conductivity of the metal, which can act as a current shunt, causing profound effects on the transport process. Here we examine the use of Au-coated nanocapillary array membranes (Au NCAMs) as electrically addressable fluid control elements in multi-layer microfluidic architectures. Three alternative methods for fluid injection across Au NCAMs are presented: electrokinetic injection across NCAMs with Au coated on one side (asymmetric NCAM), electrokinetic injection across NCAMs with an embedded Au layer (symmetric NCAM), and field-free electroosmotic flow (EOF) pumping across either type of Au NCAM. Injection efficiency across asymmetric NCAMs depends on the orientation of the asymmetric membrane relative to the driving potential. Efficient injections are enabled when the Au coating is on the receiving side of the membrane, however, some distortion of the injected volume element is observed, especially with large injection potentials. These results for asymmetric membranes agree qualitatively with two-dimensional numerical simulations of injections across a single slit pore, which suggest that the direction-selective transport behavior is related to electrophoretic transport of the anionic fluorescein probe. Reproducible, high quality injections are also achieved in symmetric Au NCAMs having an embedded gold nanoband region within the nanopores. Nanoband Au NCAMs are excellent candidates for a range of applications, including high efficiency electrochemical sensing, electrochemically catalyzed conversion or pretreatment and label free sensing utilizing extraordinary optical transmission. EOF pumping could be an alternative to electrokinetic injections in some applications, however, this approach is only useful for relatively large pore sizes (>400 nm) and presents considerably worse sample spreading via Taylor dispersion.

Development of a troponin I biosensor using a peptide obtained through phage display.

A small synthetic peptide with nanomolar affinity for cardiac troponin I (TnI), previously identified from a polyvalent phage displayed library, has been immobilized on a gold surface for TnI detection. The binding affinity of gold-immobilized peptides for TnI was studied and compared with that of phage-immobilized peptides. Quartz crystal microbalance (QCM), cyclic voltammetry, and electrochemical impedance spectroscopy (EIS) were used to monitor both the immobilization and target binding processes. All three techniques show that the binding is specific for TnI as compared to a streptavidin (SA) control. The response curves obtained at TnI concentrations ranging from 0 to 10 µg/mL, using both QCM and EIS, were also compared. For the EIS measurements, the sensitivity was 0.30 ± 0.030 normalized impedance/(µg/mL) and the limit of detection (LOD) was 0.34 µg/mL. Using the QCM, a sensitivity of 18 ± 1 Hz/(µg/mL) was obtained, corresponding to an LOD of 0.11 µg/mL. Although the QCM demonstrated a lower LOD as compared to EIS, the latter technique exhibited a larger linear dynamic range than QCM. In a relevant tissue culture milieu, Minimum Essential Media (MEM), the sensitivity of the EIS measurement was greater than that obtained in a phosphate buffer system (PBS). The kinetics of target binding using QCM were analyzed by two independent methods, and the dissociation constants (K(D) = 66 ± 4 nM and 17 ± 8 nM) were an order of magnitude higher than that calculated for the polyvalent phage particles (K(D) = 2.5 ± 0.1 nM). Even though the affinity of the immobilized peptides for TnI was somewhat reduced, overall, these results demonstrate that peptides obtained from the biopanning of phage display libraries can be readily used as sensing probes in biosensor development.

Rapid analysis of perchlorate in drinking water at parts per billion levels using microchip electrophoresis.

A microchip capillary electrophoresis (MCE) system has been developed for the determination of perchlorate in drinking water. The United States Environmental Protection Agency (USEPA) recently proposed a health advisory limit for perchlorate in drinking water of 15 parts per billion (ppb), a level requiring large, sophisticated instrumentation, such as ion chromatography coupled with mass spectrometry (IC-MS), for detection. An inexpensive, portable system is desired for routine online monitoring applications of perchlorate in drinking water. Here, we present an MCE method using contact conductivity detection for perchlorate determination. The method has several advantages, including reduced analysis times relative to IC, inherent portability, high selectivity, and minimal sample pretreatment. Resolution of perchlorate from more abundant ions was achieved using zwitterionic, sulfobetaine surfactants, N-hexadecyl-N,N-dimethyl-3-ammonio-1-propane sulfonate (HDAPS) and N-tetradecyl-N,N-dimethyl-3-ammonio-1-propane sulfonate (TDAPS). The system performance and the optimization of the separation chemistry, including the use of these surfactants to resolve perchlorate from other anions, are discussed in this work. The system is capable of detection limits of 3.4 +/- 1.8 ppb (n = 6) in standards and 5.6 +/- 1.7 ppb (n = 6) in drinking water.

High affinity peptides for the recognition of the heart disease biomarker troponin I identified using phage display.

Troponin I is a specific and sensitive clinical biomarker for myocardial injury. In this study we have used polyvalent phage display to isolate unique linear peptide motifs which recognize both the human and rat homologs of troponin I. The peptide specific for human troponin I has a sequence of FYSHSFHENWPS and the peptide specific for the rat troponin I has a sequence of FHSSWPVNGSTI. Enzyme-linked immunosorbent assays (ELISAs) were used to evaluate the binding interactions, and the two phage-displayed peptides exhibited some cross-reactivity, but they were both more specific for the troponin I homolog they were selected against. The binding affinities of the phage-displayed peptides were decreased by the presence of complex tissue culture media (MEM), and the addition of 10% calf serum further interfered with the binding of the target proteins. Kinetic indirect phage ELISAs revealed that both troponin I binding peptides were found to have nanomolar affinities for the troponin proteins while attached to the phage particles. To our knowledge, this is the first example of isolation and characterization of troponin I binders using phage display technology. These new peptides may have potential utility in the development of new clinical assays for cardiac injury as well as in monitoring of cardiac cells grown in culture.

Effects of millimeter wave carbon fibers on filter-feeding freshwater invertebrates.

The purpose of our study was to investigate the sub-lethal effects of millimeter wave carbon fibers (MWCF), a military obscurant, on filter-feeding freshwater invertebrates. We observed decreased survival, reproduction, and oxygen consumption in Daphnia magna at realistic loading rates. In experiments with the Asiatic clam (Corbicula fluminea), soft tissue dry weight and tissue condition index were not significantly different among control and MWCF exposed treatments; however, using a (15)N labeled alga as food, we observed decreased nitrogen turnover in tissues of clams exposed to MWCF, suggesting lower filtering or ingestion rates. Our findings combined with previous demonstrations of MWCF toxicity to green algae suggest that over a period of several months, bivalve growth may be inhibited, and cladoceran populations may be even more strongly affected by MWCF. Given that these fibers are persistent, further experiments should be conducted to determine the longer-term effects of contamination of water bodies with MWCF.

Synthesis, characterization, DNA binding, topoisomerase inhibition, and apoptosis induction studies of a novel cobalt(III) complex with a thiosemicarbazone ligand.

In this study, 9-anthraldehyde-N(4)-methylthiosemicarbazone (MeATSC) 1 and [Co(phen)2(O2CO)]Cl·6H2O 2 (where phen = 1,10-phenanthroline) were synthesized. [Co(phen)2(O2CO)]Cl·6H2O 2 was used to produce anhydrous [Co(phen)2(H2O)2](NO3)33. Subsequently, anhydrous [Co(phen)2(H2O)2](NO3)33 was reacted with MeATSC 1 to produce [Co(phen)2(MeATSC)](NO3)3·1.5H2O·C2H5OH 4. The ligand, MeATSC 1 and all complexes were characterized by elemental analysis, FT IR, UV-visible, and multinuclear NMR (1H, 13C, and 59Co) spectroscopy, along with HRMS, and conductivity measurements, where appropriate. Interactions of MeATSC 1 and complex 4 with calf thymus DNA (ctDNA) were investigated by carrying out UV-visible spectrophotometric studies. UV-visible spectrophotometric studies revealed weak interactions between ctDNA and the analytes, MeATSC 1 and complex 4 (Kb = 8.1 × 105 and 1.6 × 104 M-1, respectively). Topoisomerase inhibition assays and cleavage studies proved that complex 4 was an efficient catalytic inhibitor of human topoisomerases I and IIα. Based upon the results obtained from the 3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium (MTS) assay on 4T1-luc metastatic mammary breast cancer cells (IC50 = 34.4 ±â€¯5.2 µM when compared to IC50 = 13.75 ±â€¯1.08 µM for the control, cisplatin), further investigations into the molecular events initiated by exposure to complex 4 were investigated. Studies have shown that complex 4 activated both the apoptotic and autophagic signaling pathways in addition to causing dissipation of the mitochondrial membrane potential (ΔΨm). Furthermore, activation of cysteine-aspartic proteases3 (caspase 3) in a time- and concentration-dependent manner coupled with the ΔΨm, studies implicated the intrinsic apoptotic pathway as the major regulator of cell death mechanism.

A FRET-based method for probing the conformational behavior of an intrinsically disordered repeat domain from Bordetella pertussis adenylate cyclase.

A better understanding of the conformational changes exhibited by intrinsically disordered proteins is necessary as we continue to unravel their myriad biological functions. In repeats in toxin (RTX) domains, calcium binding triggers the natively unstructured domain to adopt a beta roll structure. Here we present an in vitro Forster resonance energy transfer (FRET)-based method for the investigation of the conformational behavior of an RTX domain from the Bordetella pertussis adenylate cyclase consisting of nine repeat units. Equilibrium and stopped-flow FRET between fluorescent proteins, attached to the termini of the domain, were measured in an analysis of the end-to-end distance changes in the RTX domain. The method was complemented with circular dichroism spectroscopy, tryptophan fluorescence, and bis-ANS dye binding. High ionic strength was observed to decrease the calcium affinity of the RTX domain. A truncation and single amino acid mutations yielded insights into the structural determinants of beta roll formation. Mutating the conserved Asp residue in one of the nine repeats significantly reduced the affinity of the domains for calcium ions. Removal of the sequences flanking the repeat domain prevented folding, but replacing them with fluorescent proteins restored the conformational behavior, suggesting an entropic stabilization. The FRET-based method is a useful technique that complements other low-resolution techniques for investigating the dynamic conformational behavior of the RTX domain and other intrinsically disordered protein domains.

Rapid generation of spatially and temporally controllable long-range concentration gradients in a microfluidic device.

The ability to rapidly generate concentration gradients of diffusible molecules has important applications in many chemical and biological studies. Here we established spatially and temporally controllable concentration gradients of molecules (i.e. proteins or toxins) in a portable microfluidic device in an easy and rapid manner. The formation of the concentration gradients was initiated by a passive-pump-induced forward flow and further optimized during an evaporation-induced backward flow. The centimeter-long gradients along the microfluidic channel were shown to be spatially and temporally controlled by the backward flow. The gradient profile was stabilized by stopping the flow. Computational simulations of this dynamic process illustrated the combined effects of convection and diffusion on the gradient generation, and fit well with the experimental data. To demonstrate the applications of this methodology, a stabilized concentration gradient of a cardiac toxin, alpha-cypermethrin, along the microchannel was used to test the response of HL-1 cardiac cells in the micro-device, which correlated with toxicity data obtained from multi-well plates. The approach presented here may be useful for many biological and chemical processes that require rapid generation of long-range gradients in a portable microfluidic device.

Use of the thyrocyte sodium iodide symporter as the basis for a perchlorate cell-based assay.

Perchlorates are strong oxidants widely employed in military and civilian energetic materials and recently have been scrutinized as persistent environmental pollutants. The perchlorate anion, ClO(4)(-), is a well-known and potent competitive inhibitor of iodide transport by the sodium iodide symporter (NIS) expressed in the basolateral membranes of thyroid follicular cells (thyrocytes). Iodide uptake by thyroid follicular cells is rapid and reproducible. The competitive radiotransporter assay in this study shows promise as a rapid and convenient method to assay for ClO(4)(-) in water samples at the nM level. This work describes the initial efforts to define the assay conditions that enhance NIS selectivity for ClO(4)(-). Experiments of 10 min co-incubation of ClO(4)(-) and (125)I(-) demonstrate a more significant effect on (125)I(-) transport, with a quantifiable ClO(4)(-) concentration range of 50 nM (5 ppb) to 2 microM (200 ppb), and IC(50) of 180 nM (18 ppb), nearly three-fold lower than previous reports. Since the IC(50) in our assay for other known competitor anions (SCN(-), ClO(3)(-), NO(3)(-)) remains unchanged from previous research, the increased sensitivity for ClO(4)(-) also produces a three-fold enhancement in selectivity. In addition to the possible applicability of the thyrocyte to the development of a cellular perchlorate biosensor, we propose that the high affinity of the NIS for ClO(4)(-) also creates the potential for exploiting this membrane protein as a selective, sensitive, and broadly applicable biomechanical mechanism for controlled movement and concentration of perchlorate.

Evaluating a multi-panel air cathode through electrochemical and biotic tests.

To scale up microbial fuel cells (MFCs), larger cathodes need to be developed that can use air directly, rather than dissolved oxygen, and have good electrochemical performance. A new type of cathode design was examined here that uses a "window-pane" approach with fifteen smaller cathodes welded to a single conductive metal sheet to maintain good electrical conductivity across the cathode with an increase in total area. Abiotic electrochemical tests were conducted to evaluate the impact of the cathode size (exposed areas of 7 cm2, 33 cm2, and 6200 cm2) on performance for all cathodes having the same active catalyst material. Increasing the size of the exposed area of the electrodes to the electrolyte from 7 cm2 to 33 cm2 (a single cathode panel) decreased the cathode potential by 5%, and a further increase in size to 6200 cm2 using the multi-panel cathode reduced the electrode potential by 55% (at 0.6 A m-2), in a 50 mM phosphate buffer solution (PBS). In 85 L MFC tests with the largest cathode using wastewater as a fuel, the maximum power density based on polarization data was 0.083 ±â€¯0.006 W m-2 using 22 brush anodes to fully cover the cathode, and 0.061 ±â€¯0.003 W m-2 with 8 brush anodes (40% of cathode projected area) compared to 0.304 ±â€¯0.009 W m-2 obtained in the 28 mL MFC. Recovering power from large MFCs will therefore be challenging, but several approaches identified in this study can be pursued to maintain performance when increasing the size of the electrodes.

Ultrascalable Multifunctional Nanoengineered Copper and Aluminum for Antiadhesion and Bactericidal Applications.

Biofouling disrupts the surface functionality and integrity of engineered substrates. A variety of natural materials such as plant leaves and insect wings have evolved sophisticated physical mechanisms capable of preventing biofouling. Over the past decade, several reports have pinpointed nanoscale surface topography as an important regulator of surface adhesion and growth of bacteria. Although artificial nanoengineered features have been used to create bactericidal materials that kill adhered bacteria, functional surfaces capable of synergistically providing antiadhesion and bactericidal properties remain to be developed. Furthermore, fundamental questions pertaining to the need for intrinsic hydrophobicity to achieve bactericidal performance and the role of structure length scale (nano vs micro) are still being explored. Here, we demonstrate highly scalable, cost-effective, and efficient nanoengineered multifunctional surfaces that possess both antiadhesion and bactericidal properties on industrially relevant copper (Cu) and aluminum (Al) substrates. We characterize antiadhesion and bactericidal performance using a combination of scanning electron microscopy (SEM), atomic force microscopy (AFM), live/dead bacterial staining and imaging, as well as solution-phase and Petrifilm measurements of bacterial viability. Our results showed that nanostructures created on both Cu and Al were capable of physical deformation of adhered Escherichia coli bacteria. Bacterial viability measurements on both Cu and Al indicated a complex interaction between the antiadhesion and bactericidal nature of these materials and their surface topography, chemistry, and structure. Increased superhydrophobicity greatly decreased bacterial adhesion while not significantly influencing surface bactericidal performance. Furthermore, we observed that more densely packed nanoscale structures improved antiadhesion properties when compared to larger features, even over extended time scales of up to 24 h. Our data suggests that the superhydrophobic Al substrate possesses superior antiadhesion and bactericidal effects, even over long time courses. The techniques and insights presented here will inform future work on antiadhesion and bactericidal multifunctional surfaces and enable their rational design.