RESUMO
Anti-parity-time-symmetric Hamiltonians show an enhanced sensitivity to external perturbations that can be used for high-performance angular velocity sensing. Dissipative coupling is a valuable way for realizing anti-PT-symmetric Hamiltonians with optical resonators and is usually obtained by means of auxiliary waveguides. Here, we model and experimentally show the dissipative coupling between two counterpropagating modes of a single resonator, by means of a Bragg-grating placed in the feeding bus. The proposed solution enables the possibility of accurately designing the dissipative coupling strength in integrated non-Hermitian gyroscopes, thus providing high flexibility in the design of the proposed sensor. Moreover, we theoretically and experimentally demonstrate that the dissipative coupling between two counterpropagating modes of the same resonant cavity can give rise to an asymmetric Fano resonance.
RESUMO
We present and experimentally evaluate the use of transfer learning to address experimental data scarcity when training neural network (NN) models for Mach-Zehnder interferometer mesh-based optical matrix multipliers. Our approach involves pretraining the model using synthetic data generated from a less accurate analytical model and fine-tuning it with experimental data. Our investigation demonstrates that this method yields significant reductions in modeling errors compared to using an analytical model or a standalone NN model when training data is limited. Utilizing regularization techniques and ensemble averaging, we achieve <1 dB root-mean-square error on the 3×3 matrix weights implemented by a photonic chip while using only 25% of the available data.
RESUMO
The sequence assembly algorithms have rapidly evolved with the vigorous growth of genome sequencing technology over the past two decades. Assembly mainly uses the iterative expansion of overlap relationships between sequences to construct the target genome. The assembly algorithms can be typically classified into several categories, such as the Greedy strategy, Overlap-Layout-Consensus (OLC) strategy, and de Bruijn graph (DBG) strategy. In particular, due to the rapid development of third-generation sequencing (TGS) technology, some prevalent assembly algorithms have been proposed to generate high-quality chromosome-level assemblies. However, due to the genome complexity, the length of short reads, and the high error rate of long reads, contigs produced by assembly may contain misassemblies adversely affecting downstream data analysis. Therefore, several read-based and reference-based methods for misassembly identification have been developed to improve assembly quality. This work primarily reviewed the development of DNA sequencing technologies and summarized sequencing data simulation methods, sequencing error correction methods, various mainstream sequence assembly algorithms, and misassembly identification methods. A large amount of computation makes the sequence assembly problem more challenging, and therefore, it is necessary to develop more efficient and accurate assembly algorithms and alternative algorithms.
Assuntos
Algoritmos , Genoma , Análise de Sequência de DNA/métodos , Sequência de Bases , Sequenciamento de Nucleotídeos em Larga Escala/métodos , SoftwareRESUMO
We propose and experimentally demonstrate a high-order coupled-resonator optical waveguide (CROW) nanobeam filter with semi-symmetrical Fano resonance enhancement. Thanks to the tight arrangement of multiple nanobeams and assistance of the partial transmission element, the designed filter has a high-contrast transmission and low insertion loss. Finally, the fabricated filter has a compact size of 20µm×10µm, a high extinction ratio as much as 70 dB, and an insertion loss as low as 1 dB. This filter shows a passive structure without thermal control configuration for calibration on each resonator. This compact filter can be a basic building block for various applications requiring high extinction ratio filtering, such as single-photon source filtering of integrated photon chips.
RESUMO
Silicon photonic integrated circuits (PICs) show great potential for many applications. The phase tuning technique is indispensable and of great importance in silicon PICs. An optical phase shifter with balanced overall performance on power consumption, insertion loss, footprint, and modulation bandwidth is essential for harnessing large-scale integrated photonics. However, few proposed phase shifter schemes on various platforms have achieved a well-balanced performance. In this Letter, we experimentally demonstrate a thermo-optic phase shifter based on a densely distributed silicon spiral waveguide on a silicon-on-insulator platform. The phase shifter shows a well-balanced performance in all aspects. The electrical power consumption is as low as 3 mW to achieve a π phase shift, the optical insertion loss is 0.9 dB per phase shifter, the footprint is 67×28µm2 under a standard silicon photonics fabrication process without silicon air trench or undercut process, and the modulation bandwidth is measured to be 39 kHz.
RESUMO
We present beyond 100 Gbps space-division multiplexing passive optical network (SDM-PON) systems using commercial 10G-class directly modulated laser (DML) modulated with 25/28 Gbps data signals, with polarization-diversity micro-ring resonator (PD-MRR) to improve the extinction ratio (ER). A high-count multi-core fiber (HC-MCF) with low-crosstalk (XT) is used in the system, simultaneously increasing the transmission capacity and splitting ratio. Different cores of the HC-MCF are used for upstream (US) and downstream (DS) transmission, avoiding the Rayleigh backscattering noise. Thanks to compatibility with time-division multiplexing (TDM), the splitting ratio could be further increased. In addition, both symmetric and asymmetric SDM-PON architectures are proposed to meet different requirements of users. In the SDM-PON systems, a simple intensity modulation/ directly detection (IM/DD) is applied without digital signal processing (DSP), which may be a promising candidate for future large-capacity and high splitting ratio access networks.
RESUMO
We experimentally demonstrate orbital angular momentum (OAM) modes emission from a high emission efficiency OAM emitter for 20-Gbit/s quadrature phase-shift keying (QPSK) carrying data transmission in few-mode fiber (FMF). The device is capable of emitting vector optical vortices carrying well-defined OAM efficiently with the efficiency of the device >37%. Seven modes propagate through a 2-km two-mode and a 3.6-km three-mode FMF with measured optical signal-to-noise ratio (OSNR) penalties less than 4 dB at a bit-error rate (BER) of 2 × 10-3. The demonstrations with favorable performance pave the way to incorporate silicon photonic integrated devices as transceivers in an OAM-enabled optical fiber communication link.
RESUMO
Photonic integrated devices that emit vortex beam carrying orbital angular momentum are becoming key components for multiple applications. Here we propose and demonstrate a high-efficiency vortex beam emitter based on a silicon micro-ring resonator integrated with a metal mirror. Such a compact emitter is capable of generating vortex beams with a high efficiency and small divergence angle. Vector vortex beams of various topological charges are selectively generated by the emitter at different wavelengths with an emission efficiency of up to 37%.
RESUMO
A novel concept to generate a linear chirped microwave signal is proposed and experimentally demonstrated. The frequency to time mapping method is employed, where the photonic crystal waveguide Mach-Zehnder interferometer structure acts as the spectral shaper thanks to the slow light effect. By optimizing the structural parameters of the photonic crystal waveguide, a linear chirped microwave signal with the time-bandwidth product of about 30 is experimentally obtained. The impact of the slow light photonic crystal waveguide on the generated linear chirped microwave signal is also investigated. The utilization of the slow light effect brings in significant advantages, including the ultra-small footprint of 0.096 mm2 and simple structure to our scheme, which may be of great importance towards its potential applications.
RESUMO
A photonic differentiator (DIFF) plays a crucial role in photonic circuits. Despite the fact that a DIFF having a terahertz bandwidth has been reported, the practical bandwidth is limited to being a bandpass response. In this Letter, we propose the concept of a bandwidth-adaptable DIFF, which exploits the slow light effect in a photonic crystal waveguide (PhCW) to overcome the inherent bandwidth limitation of current photonic DIFFs. We fabricated a PhCW Mach-Zehnder interferometer (PhCW-MZI) on the silicon-on-isolator material platform to validate our concept. Input Gaussian pulses with full width to half-maximums (FWHMs) ranging from 2.7 to 81.4 ps are accurately differentiated using our PhCW-MZI. Our all-passive scheme circumvents the bandwidth bottlenecks of previously reported photonic DIFFs and can greatly broaden the application area of photonic DIFFs.
RESUMO
We derive from Maxwell's equations full-vectorial nonlinear propagation equations of four-wave mixing valid in straight semiconductor-on-insulator waveguides. Special attention is given to the resulting effective mode area, which takes a convenient form known from studies in photonic crystal fibers, but has not been introduced in the context of integrated waveguides. We show that the difference between our full-vectorial effective mode area and the scalar equivalent often referred to in the literature may lead to mistakes when evaluating the nonlinear refractive index and optimizing designs of new waveguides. We verify the results of our derivation by comparing it to experimental measurements in a silicon-on-insulator waveguide, taking tolerances on fabrication parameters into account.
RESUMO
We design and experimentally verify a topology optimized low-loss and broadband two-mode (de-)multiplexer, which is (de-)multiplexing the fundamental and the first-order transverse-electric modes in a silicon photonic wire. The device has a footprint of 2.6 µm x 4.22 µm and exhibits a loss <1.2 dB in a 100 nm bandwidth measured around 1570 nm. The measured cross talk is <-12 dB and the extinction ratio is >14 dB in the C-band. Furthermore, we demonstrate that the design method can be expanded to include more modes, in this case including also the second order transverse-electric mode, while maintaining functionality.
RESUMO
Arbitrary waveform generation has been widely used in optical communication, radar system and many other applications. We propose and experimentally demonstrate a silicon-on-insulator (SOI) on chip optical arbitrary waveform generator, which is based on Taylor synthesis method. In our scheme, a Gaussian pulse is launched to some cascaded microrings to obtain first-, second- and third-order differentiations. By controlling amplitude and phase of the initial pulse and successive differentiations, we can realize an arbitrary waveform generator according to Taylor expansion. We obtain several typical waveforms such as square waveform, triangular waveform, flat-top waveform, sawtooth waveform, Gaussian waveform and so on. Unlike other schemes based on Fourier synthesis or frequency-to-time mapping, our scheme is based on Taylor synthesis method. Our scheme does not require any spectral disperser or large dispersion, which are difficult to fabricate on chip. Our scheme is compact and capable for integration with electronics.
RESUMO
Graphene opens up for novel optoelectronic applications thanks to its high carrier mobility, ultralarge absorption bandwidth, and extremely fast material response. In particular, the opportunity to control optoelectronic properties through tuning of the Fermi level enables electro-optical modulation, optical-optical switching, and other optoelectronics applications. However, achieving a high modulation depth remains a challenge because of the modest graphene-light interaction in the graphene-silicon devices, typically, utilizing only a monolayer or few layers of graphene. Here, we comprehensively study the interaction between graphene and a microring resonator, and its influence on the optical modulation depth. We demonstrate graphene-silicon microring devices showing a high modulation depth of 12.5 dB with a relatively low bias voltage of 8.8 V. On-off electro-optical switching with an extinction ratio of 3.8 dB is successfully demonstrated by applying a square-waveform with a 4 V peak-to-peak voltage.
RESUMO
We report the design and fabrication of a compact multi-core fiber fan-in/fan-out using a grating coupler array on the SOI platform. The grating couplers are fully-etched, enabling the whole circuit to be fabricated in a single lithography and etching step. Thanks to the apodized design for the grating couplers and the introduction of an aluminum reflective mirror, a highest coupling efficiency of -3.8 dB with 3 dB coupling bandwidth of 48 nm and 1.5 dB bandwidth covering the whole C band, together with crosstalk lower than -32 dB are demonstrated.
RESUMO
We propose and demonstrate an optical arbitrary waveform generator and high-order photonic differentiator based on a four-tap finite impulse response (FIR) silicon-on-insulator (SOI) on-chip circuit. Based on amplitude and phase modulation of each tap controlled by thermal heaters, we obtain several typical waveforms such as triangular waveform, sawtooth waveform, square waveform and Gaussian waveform, etc., assisted by an optical frequency comb injection. Unlike other proposed schemes, our scheme does not require a spectral disperser which is difficult to fabricate on chip with high resolution. In addition, we demonstrate first-, second- and third-order differentiators based on the optical pulse shaper. Our scheme can switch the differentiator patterns from first- to third-order freely. In addition, our scheme has distinct advantages of compactness, capability for integration with electronics.
RESUMO
An ultra-compact and broadband higher order-mode pass filter in a 1D photonic crystal silicon waveguide is proposed and experimentally demonstrated. The photonic crystal is designed for the lower order mode to work in the photonic band gap, while the higher order mode is located in the air band. Consequently, light on the lower order mode is prohibited to pass through the filter, while light on a higher order mode can be converted to a Bloch mode in the photonic crystal and pass through the filter with low insertion loss. As an example, we fabricate a â¼15-µm-long first-order-mode pass filter that filters out the fundamental mode and provides a measured insertion loss of â¼1.8 dB for the first-order-mode pass signals. The extinction ratio is measured to be around 50 dB (with a variation of ±10 dB due to the detection limitation of the measurement setup) in the measured wavelength range from 1480 to 1580 nm. Additionally, calculations predict the extinction ratio to be larger than 50 dB in a 170 nm broad bandwidth.
RESUMO
We propose and demonstrate all-optical mode-selective wavelength conversion in a silicon waveguide. The mode-selective wavelength conversion relies on strong four-wave mixing when pump and signal light are on the same spatial mode, while weak four-wave mixing is obtained between different modes due to phase mismatch. A two-mode division multiplexing circuit with tapered directional coupler based (de)multiplexers and a multimode waveguide is designed and fabricated for this application. Experimental results show clear eye-diagrams and moderate power penalties for the wavelength conversion of both modes.
Assuntos
Modelos Químicos , Espalhamento de Radiação , Silício/química , Ressonância de Plasmônio de Superfície/instrumentação , Ressonância de Plasmônio de Superfície/métodos , Simulação por Computador , Desenho Assistido por Computador , Desenho de Equipamento , Análise de Falha de Equipamento , LuzRESUMO
We propose and demonstrate a silicon-on-insulator (SOI) on-chip programmable filter based on a four-tap finite impulse response structure. The photonic filter is programmable thanks to amplitude and phase modulation of each tap controlled by thermal heaters. We further demonstrate the tunability of the filter central wavelength, bandwidth and variable passband shape. The tuning range of the central wavelength is at least 42% of the free spectral range. The bandwidth tuning range is at least half of the free spectral range. Our scheme has distinct advantages of compactness, capability for integrating with electronics.
Assuntos
Eletrodos , Calefação/instrumentação , Interferometria/instrumentação , Dispositivos Ópticos , Processamento de Sinais Assistido por Computador/instrumentação , Silício/química , Desenho Assistido por Computador , Desenho de Equipamento , Análise de Falha de Equipamento , Fótons , Integração de SistemasRESUMO
Polarization insensitive wavelength conversion of a 40 Gb/s non-return-to-zero (NRZ) differential phase-shift keying (DPSK) data signal is demonstrated using four-wave mixing (FWM) in a silicon nanowire circuit. Polarization independence is achieved using a diversity circuit based on polarization rotators and splitters, which is fabricated by a simple process on the silicon-on-insulator (SOI) platform. Error-free performance is achieved with only 0.5 dB of power penalty compared to the wavelength conversion of a signal with well optimized input polarization. Additionally, data transmission over 161 km standard single-mode fiber (SSMF) is demonstrated at 40 Gb/s using optical phase conjugation (OPC) in the proposed circuit.