Adhesion of Grafted-to Polyelectrolyte Brushes Functionalized with Calix[4]resorcinarene and Deposited as a Monolayer.

Polyelectrolyte adhesives, either poly[2-(dimethylamino)ethyl methacrylate] or poly(methacrylic acid), functionalized with a surface-active calix[4]resorcinarene were grafted onto silicon wafers. Adhesion studies on these grafted-to brushes using polyelectrolyte hydrogels of opposite charge showed that it is the calix[4]resorcinarene, rather than adsorption of polyelectrolyte monomers, that adheres the brush to the silicon substrate. The adhesion measured was similar to that measured using polymers grafted from the surface, and was stronger than a control layer of poly(vinyl acetate) under the same test conditions. The limiting factor was determined to be adhesive failure at the hydrogel-brush interface, rather than the brush-silicon interface. Therefore, the adhesion has not been adversely affected by changing from a grafted-from to a grafted-to brush, demonstrating the possibility of a one-pot approach to creating switchable adhesives.

Competition between substrate-mediated π-π stacking and surface-mediated T(g) depression in ultrathin conjugated polymer films.

We report surface and interface effects in dynamics and chain conformation in the thin film of conjugated polymer PCDTBT. To probe dynamic anomalies, we measure the glass transition temperature (T(g)) of PCDTBT films as a function of thickness, and find that there is a significant depression in T(g) for films less than 100 nm thick; a result qualitatively similar to that observed in many other polymer film systems. However, for films less than 40 nm, the T(g) converges to a constant value of 20 K below its bulk value. Grazing incidence X-ray diffraction shows depth-dependent molecular organization that is associated with the unusual thickness-dependent dynamics.

Influence of Additives on the In Situ Crystallization Dynamics of Methyl Ammonium Lead Halide Perovskites.

Understanding the kinetics of the crystallization process for organometal halide perovskite formation is critical in determining the crystalline, nanoscale morphology and therefore the electronic properties of the films produced during thin film formation from solution. In this work, in situ grazing incidence small-angle X-ray scattering (GISAXS) and optical microscopy measurements are used to investigate the processes of nucleation and growth of pristine mixed halide perovskite (MAPbI3-x Cl x ) crystalline films deposited by bar coating at 60 °C, with and without additives in the solution. A small amount of 1,8-diiodooctane (DIO) and hydriodic acid (HI) added to MAPbI3-x Cl x is shown to increase the numbers of nucleation centers promoting heterogeneous nucleation and accelerate and modify the size of nuclei during nucleation and growth. A generalized formation mechanism is derived from the overlapping parameters obtained from real-time GISAXS and optical microscopy, which revealed that during nucleation, perovskite precursors cluster before becoming the nuclei that function as elemental units for subsequent formation of perovskite crystals. Additive-free MAPbI3-x Cl x follows reaction-controlled growth, in contrast with when DIO and HI are present, and it is highly possible that the growth then follows a hindered diffusion-controlled mechanism. These results provide important details of the crystallization mechanisms occurring and will help to develop greater control over perovskite films produced.

Perovskite Crystallization Dynamics during Spin-Casting: An In Situ Wide-Angle X-ray Scattering Study.

In situ wide-angle X-ray scattering (WAXS) has been measured during the spin coating process used to make the precursor films required for the formation of thin films of perovskite. A customized hollow axis spin coater was developed to permit the scattered X-rays to be collected in transmission geometry during the deposition process. Spin coating is the technique most commonly used in laboratories to make thin perovskite films. The dynamics of spin-casting MAPbI3-x Cl x and FAPbI3-x Cl x films have been investigated and compared to investigate the differences between the dynamics of MAPbI3-x Cl x and FAPbI3-x Cl x film formation. In particular, we focus on the crystallization dynamics of the precursor film formation. When casting MAPbI3-x Cl x , we observed relatively fast 1D crystallization of the intermediate product MA2PbI3Cl. There was an absence of the desired perovskite phase formed directly; it only appeared after an annealing step that converted the MA2PbI3Cl to MAPbI3. In contrast, slower crystallization via a 3D precursor was observed for FAPbI3-x Cl x film formation compared to MAPbI3-x Cl x . Another important finding was that some FAPbI3-x Cl x perovskite was generated directly during spin-casting before annealing. These findings indicate that there are significant differences between the crystallization pathways for these two perovskite materials. These are likely to explain the differences in the lifetimes of the resulting perovskite solar cell devices produced using FA and MA cations.

Low cost, high sensitivity detection of waterborne Al3+ cations and F- anions via the fluorescence response of a morin derivative dye.

Morin dye is known as a cheap and readily available selective 'off → on' fluorescent sensitiser when immobilised in a phase transfer membrane for the detection of Al3+ ions. Here, a morin derivative, NaMSA, which readily dissolves in water with good long-term stability is used in conjunction with a fibre optic transducer with lock-in detection to detect Al3+ in drinking water below the potability limit. The combination of a water soluble dye and the fibre optic transducer require neither membrane preparation nor a fluorescence spectrometer yet still display a high figure-of- merit. The known ability to recover morin-based Al3+ cation sensors selectively by exposure to fluoride (F-) anions is further developed enabling a complementary sensing of either fluoride anions, or aluminium cations, using the same dye with a sub-micromolar limit-of-detection for both ions. The sensor performance parameters compare favourably to prior reports on both aqueous aluminium and fluoride ion sensing.

Adaptive and sensitive fibre-optic fluorimetric transducer for air- and water-borne analytes.

A sensitive fibre optic fluorescence intensity meter has been designed and built as a transducer to detect quenching of conjugated polymer fluorescence with minimum adjustment between air- and waterborne analytes. Only generic, commercially available parts including optical fibres, solvents, airbrush, standard optical and electronic parts, and a digital lock-in amplifier have been used, avoiding the need for a fluorescence spectrometer. To test the instrument, optical fibres were sensitised with the generic fluorescent poly(phenylene-vinylene) derivative MDMO-PPV and exposed to a variety of vapour pressures, and concentrations in water, of the nitroaromatic explosive 2,4 dinitrotoluene (DNT). We establish dimensionless Stern-Volmer constants (KSV) and limit-of-detection (LoD) for air- and water-borne DNT as KSV(air) = 1.4 × 107vs. KSV(water) = 5.8 × 106 and LoD(air) = 10.9 ppb and LoD(water) = 56 ppb. These LoDs compare favourably to prior reports. We consider our study of the MDMO-PPV/DNT system as a successful test of our transducer design and recommend its wider use.

Determination of the Thin-Film Structure of Zwitterion-Doped Poly(3,4-ethylenedioxythiophene):Poly(styrenesulfonate): A Neutron Reflectivity Study.

Doping poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) is known to improve its conductivity; however, little is known about the thin-film structure of PEDOT:PSS when doped with an asymmetrically charged dopant. In this study, PEDOT:PSS was doped with different concentrations of the zwitterion 3-( N, N dimethylmyristylammonio)propanesulfonate (DYMAP), and its effect on the bulk structure of the films was characterized by neutron reflectivity. The results show that at a low doping concentration, the film separates into a quasi-bilayer structure with lower roughness (10%), increased thickness (18%), and lower electrical conductivity compared to the undoped sample. However, when the doping concentration increases, the film forms into a homogeneous layer and experiences an enhanced conductivity by more than an order of magnitude, a 20% smoother surface, and a 60% thickness increase relative to the pristine sample. Atomic force microscopy (AFM) and profilometry measurements confirmed these findings, and the AFM height and phase images showed the gradually increasing presence of DYMAP on the film surface as a function of the concentration. Neutron reflectivity also showed that the quasi-bilayer structure of the lowest concentration-doped PEDOT:PSS is separated by a graded rather than a well-defined interface. Our findings provide an understanding of the layer structure modification for doped PEDOT:PSS films which should prove important for device applications.

Does 1,8-diiodooctane affect the aggregation state of PC71BM in solution?

1,8-Diiodooctane (DIO) is an additive used in the processing of organic photovoltaics and has previously been reported, on the basis of small-angle X-ray scattering (SAXS) measurements, to deflocculate nano-aggregates of [6,6]-phenyl-C71-butyric acid methyl ester (PC71BM) in chlorobenzene. We have critically re-examined this finding in a series of scattering measurements using both X-rays and neutrons. With SAXS, we find that the form of the background solvent scattering is influenced by the presence of DIO, that there is substantial attenuation of the X-rays by the background solvent and that there appears to be beam-induced aggregation. All three factors call into question the suitability of SAXS for measurements on these samples. By contrast, small-angle neutron scattering (SANS) measurements, performed at concentrations of 15 mg ml-1 up to and including 40 mg ml-1, show no difference in the aggregation state for PC71BM in chlorobenzene with and without 3% DIO; we find PC71BM to be molecularly dissolved in all solvent cases. In situ film thinning measurements of spin-coated PC71BM solution with the DIO additive dry much slower. Optical imaging shows that the fullerene films possess enhanced molecular mobility in the presence of DIO and it is this which, we conclude, improves the nanomorphology and consequently solar cell performance. We propose that any compatible high boiling solvent would be expected to show the same behaviour.

Quantitative Analysis of the Molecular Dynamics of P3HT:PCBM Bulk Heterojunction.

The optoelectronic properties of blends of conjugated polymers and small molecules are likely to be affected by the molecular dynamics of the active layer components. We study the dynamics of regioregular poly(3-hexylthiophene) (P3HT):phenyl-C61-butyric acid methyl ester (PCBM) blends using molecular dynamics (MD) simulation on time scales up to 50 ns and in a temperature range of 250-360 K. First, we compare the MD results with quasi-elastic neutron-scattering (QENS) measurements. Experiment and simulation give evidence of the vitrification of P3HT upon blending and the plasticization of PCBM by P3HT. Second, we reconstruct the QENS signal based on the independent simulations of the three phases constituting the complex microstructure of such blends. Finally, we found that P3HT chains tend to wrap around PCBM molecules in the amorphous mixture of P3HT and PCBM; this molecular interaction between P3HT and PCBM is likely to be responsible for the observed frustration of P3HT, the plasticization of PCBM, and the partial miscibility of P3HT and PCBM.

Investigation of free base, Mg, Sn, and Zn substituted porphyrin LB films as gas sensors for organic analytes.

The visible absorption spectra of various substituted porphyrin compounds both in chloroform solution and as Langmuir-Blodgett (LB) solid-state films have been investigated. The porphyrin compounds examined were the Zn, Sn, Mg, and free base derivatives of 5,10,15,20-tetrakis[3,4-bis(2-ethylhexyloxy)phenyl]-21H,23H-porphine (EHO). Changes in the absorption spectra of these materials induced by their exposure to various organic compounds are reported with a view toward determining whether this is a useful approach toward an optical gas sensor.

Using neutron spin echo resolved grazing incidence scattering to investigate organic solar cell materials.

The spin echo resolved grazing incidence scattering (SERGIS) technique has been used to probe the length-scales associated with irregularly shaped crystallites. Neutrons are passed through two well defined regions of magnetic field; one before and one after the sample. The two magnetic field regions have opposite polarity and are tuned such that neutrons travelling through both regions, without being perturbed, will undergo the same number of precessions in opposing directions. In this case the neutron precession in the second arm is said to "echo" the first, and the original polarization of the beam is preserved. If the neutron interacts with a sample and scatters elastically the path through the second arm is not the same as the first and the original polarization is not recovered. Depolarization of the neutron beam is a highly sensitive probe at very small angles (<50 µrad) but still allows a high intensity, divergent beam to be used. The decrease in polarization of the beam reflected from the sample as compared to that from the reference sample can be directly related to structure within the sample. In comparison to scattering observed in neutron reflection measurements the SERGIS signals are often weak and are unlikely to be observed if the in-plane structures within the sample under investigation are dilute, disordered, small in size and polydisperse or the neutron scattering contrast is low. Therefore, good results will most likely be obtained using the SERGIS technique if the sample being measured consist of thin films on a flat substrate and contain scattering features that contains a high density of moderately sized features (30 nm to 5 µm) which scatter neutrons strongly or the features are arranged on a lattice. An advantage of the SERGIS technique is that it can probe structures in the plane of the sample.

In situ imaging and height reconstruction of phase separation processes in polymer blends during spin coating.

Spin coating polymer blend thin films provides a method to produce multiphase functional layers of high uniformity covering large surface areas. Applications for such layers include photovoltaics and light-emitting diodes where performance relies upon the nanoscale phase separation morphology of the spun film. Furthermore, at micrometer scales, phase separation provides a route to produce self-organized structures for templating applications. Understanding the factors that determine the final phase-separated morphology in these systems is consequently an important goal. However, it has to date proved problematic to fully test theoretical models for phase separation during spin coating, due to the high spin speeds, which has limited the spatial resolution of experimental data obtained during the coating process. Without this fundamental understanding, production of optimized micro- and nanoscale structures is hampered. Here, we have employed synchronized stroboscopic illumination together with the high light gathering sensitivity of an electron-multiplying charge-coupled device camera to optically observe structure evolution in such blends during spin coating. Furthermore the use of monochromatic illumination has allowed interference reconstruction of three-dimensional topographies of the spin-coated film as it dries and phase separates with nanometer precision. We have used this new method to directly observe the phase separation process during spinning for a polymer blend (PS-PI) for the first time, providing new insights into the spin-coating process and opening up a route to understand and control phase separation structures.

Modeling the kinetics of gas adsorption in multilayer porphyrin films.

A kinetic model is proposed to describe the diffusion and adsorption behavior of gas in multilayer films. Numerical solutions are attained on time scales of seconds using a finite differencing approximation to the kinetic equations. Predictions of this model are compared to experimental data for the case of NO2 diffusing through a porphyrin film. The model predicts a binding energy for the NO2 porphyrin interaction of 0.72 eV. It also predicts that for this system diffusion is the limiting factor for the adsorption response time of the film, although the recovery time is determined by both the diffusion coefficient and NO2 binding energy. Comparison with experiment gives a predicted diffusion coefficient of approximately 10(-14) m2.s-1.