Effect-Based Identification of Hazardous Antibiotic Transformation Products after Water Chlorination.

Antibiotic transformation products (TPs) generated during water treatment can be considered as an environmental concern, since they can retain part of the bioactivity of the parent compound. Effect-directed analysis (EDA) was applied for the identification of bioactive intermediates of azithromycin (AZI) and ciprofloxacin (CFC) after water chlorination. Fractionation of samples allowed the identification of bioactive intermediates by measuring the antibiotic activity and acute toxicity, combined with an automated suspect screening approach for chemical analysis. While the removal of AZI was in line with the decrease of bioactivity in chlorinated samples, an increase of bioactivity after complete removal of CFC was observed (at >0.5 mgCl2/L). Principal component analysis (PCA) revealed that some of the CFC intermediates could contribute to the overall toxicity of the chlorinated samples. Fractionation of bioactive samples identified that the chlorinated TP296 (generated from the destruction of the CFC piperazine ring) maintained 41%, 44%, and 30% of the antibiotic activity of the parent compound in chlorinated samples at 2.0, 3.0, and 4.0 mgCl2/L, respectively. These results indicate the spectrum of antibacterial activity can be altered by controlling the chemical substituents and configuration of the CFC structure with chlorine. On the other hand, the potential presence of volatile DBPs and fractionation losses do not allow for tentative confirmation of the main intermediates contributing to the acute toxic effects measured in chlorinated samples. Our results encourage further development of new and advanced methodologies to study the bioactivity of isolated unknown TPs to understand their hazardous effects in treated effluents.

Sample Enrichment for Bioanalytical Assessment of Disinfected Drinking Water: Concentrating the Polar, the Volatiles, and the Unknowns.

Enrichment methods used in sample preparation for the bioanalytical assessment of disinfected drinking water result in the loss of volatile and hydrophilic disinfection byproducts (DBPs) and hence likely tend to underestimate biological effects. We developed and evaluated methods that are compatible with bioassays, for extracting nonvolatile and volatile DBPs from chlorinated and chloraminated drinking water to minimize the loss of analytes. For nonvolatile DBPs, solid-phase extraction (SPE) with TELOS ENV as solid phase performed superior compared to ten other sorbents. SPE yielded >70% recovery of nonpurgeable adsorbable organic halogens (AOX). For volatile DBPs, cryogenic vacuum distillation performed unsatisfactorily. Purge and cold-trap with crushed ice serving as condensation nuclei achieved recoveries of 50-100% for trihalomethanes and haloacetonitriles and approximately 60-90% for purged AOX from tap water. We compared the purgeable versus the nonpurgeable fraction by combining purge-and-trap extraction with SPE. The purgeable DBP fraction enriched with the purge-and-trap method exerted a lower oxidative stress response in mammalian cells than the nonpurgeable DBPs enriched with SPE after purging, while contributions of both fractions to bacterial cytotoxicity was more variable. 37 quantified DBPs explained almost the entire AOX in the purge-and-trap extracts, but <16% in the SPE extracts demonstrating that the nonpurgeable fraction is dominated by unknown DBPs.

Disinfection by-product formation potential in response to variability in dissolved organic matter and nutrient inputs: Insights from a mesocosm study.

Changes in rainfall patterns driven by climate change affect the transport of dissolved organic matter (DOM) and nutrients through runoff to freshwater systems. This presents challenges for drinking water providers. DOM, which is a heterogeneous mix of organic molecules, serves as a critical precursor for disinfection by-products (DBPs) which are associated with adverse health effects. Predicting DBP formation is complex due to changes in DOM concentration and composition in source waters, intensified by altered rainfall frequency and intensity. We employed a novel mesocosm approach to investigate the response of DBP precursors to variability in DOM composition and inorganic nutrients, such as nitrogen and phosphorus, export to lakes. Three distinct pulse event scenarios, mimicking extreme, intermittent, and continuous runoff were studied. Simultaneous experiments were conducted at two boreal lakes with distinct DOM composition, as reflected in their color (brown and clear lakes), and bromide content, using standardized methods. Results showed primarily site-specific changes in DBP precursors, some heavily influenced by runoff variability. Intermittent and daily pulse events in the clear-water mesocosms exhibited higher haloacetonitriles (HANs) formation potential linked to freshly produced protein-like DOM enhanced by light availability. In contrast, trihalomethanes (THMs), associated with humic-like DOM, showed no significant differences between pulse events in the brown-water mesocosms. Elevated bromide concentration in the clear mesocosms critically influenced THMs speciation and concentrations. These findings contribute to understanding how changing precipitation patterns impact the dynamics of DBP formation, thereby offering insights for monitoring the mobilization and alterations of DBP precursors within catchment areas and lake ecosystems.

OrbiFragsNets. A tool for automatic annotation of orbitrap MS2 spectra using networks grade as selection criteria.

We introduce OrbiFragsNets, a tool for automatic annotation of MS2 spectra generated by Orbitrap instruments, as well as the concepts of chemical consistency and fragments networks. OrbiFragsNets takes advantage of the specific confidence interval for each peak in every MS2 spectrum, which is an unclear idea across the high-resolution mass spectrometry literature. The spectrum annotations are expressed as fragments networks, a set of networks with the possible combinations of annotations for the fragments. The model behind OrbiFragsNets is briefly described here and explained in detail in the constantly updated manual available in the GitHub repository. This new approach in MS2 spectrum de novo automatic annotation proved to perform as good as well established tools such as RMassBank and SIRIUS.•A new approach on automatic annotation of Orbitrap MS2 spectra is introduced.•Possible spectrum annotation are described as independent consistent networks, with annotations for each fragment as nodes, and annotations for the mass difference between fragments as edges.•Annotation process is described as the selection of the most connected fragments network.

N-Nitrosamines and their precursors in wastewater effluents from selected industries in Spain.

N-nitrosamines (NAs), and N-nitrosodimethylamine (NDMA) in particular, are hazardous disinfection byproducts (DBPs) relevant when wastewater impacts drinking water sources and, in water reuse practices. Our study investigates the concentrations of NDMA and five additional NAs and their precursors in industrial wastewater effluents. Aiming to identify potential differences between industrial typologies, wastewaters from 38 industries belonging to 11 types of the UN International Standard Industrial Classification of All Economic Activities system (ISIC) were analysed. Results show that the presence of most NAs and their precursors cannot be linked to a specific industry type as these were in general very different within the classes. Nevertheless, N-nitrosomethylethylamine (NMEA) and N-nitrosopiperidine (NPIP) as well as precursors for N-nitrosodiethylamine (NDEA), NPIP and N-nitrosodibuthylamine (NDBA) could be rank with different concentrations between ISIC classes (p-value < 0.05). Specific industrial wastewater with notable high concentrations of NAs and their precursors were identified too. The effluents with the highest concentration of NDMA belong to the ISIC C2011 class (Manufacture of basic chemical), while the effluents with the highest concentration of NDMA precursors were from the ISIC C1511 class (Tanning and dressing of leather; dressing and dyeing of fur). Other relevant NAs found were NDEA in ISIC class B0810 (Quarrying of stone, sand, and clay) and ISIC class C2029 (Manufacture of other chemical products).

Degradation of diclofenac and 4-chlorobenzoic acid in aqueous solution by cold atmospheric plasma source.

In this study, cold atmospheric plasma (CAP) was explored as a novel advanced oxidation process (AOP) for water decontamination. Samples with high concentration aqueous solutions of Diclofenac sodium (DCF) and 4-Chlorobenzoic acid (pCBA) were treated by plasma systems. Atmospheric pressure plasma jets (APPJs) with a 1 pin-electrode and multi-needle electrodes (3 pins) configurations were used. The plasma generated using argon as working gas was touching a stationary liquid surface in the case of pin electrode-APPJ while for multi-needle electrodes-APPJ the liquid sample was flowing during treatment. In both configurations, a commercial RF power supply was used for plasma ignition. Measurement of electrical signals enabled precise determination of power delivered from the plasma to the sample. The optical emission spectroscopy (OES) of plasma confirmed the appearance of excited reactive species in the plasma, such as hydroxyl radicals and atomic oxygen which are considered to be key reactive species in AOPs for the degradation of organic pollutants. Treatments were conducted with two different volumes (5 mL and 250 mL) of contaminated water samples. The data acquired allowed calculation of degradation efficiency and energy yield for both plasma sources. When treated with pin-APPJ, almost complete degradation of 5 mL DCF occurred in 1 min with the initial concentration of 25 mg/L and 50 mg/L, whereas 5 mL pCBA almost degraded in 10 min at the initial concentration of 25 mg/L and 40 mg/L. The treatment results with multi-needle electrodes system confirmed that DCF almost completely degraded in 30 min and pCBA degraded about 24 % in 50 min. The maximum calculated energy yield for 50 % removal was 6465 mg/kWh after treatment of 250 mL of DCF aqueous solution utilizing the plasma recirculation technique. The measurements also provided an insight to the kinetics of DCF and pCBA degradation. Degradation products and pathways for DCF were determined using LC-MS measurements.

Could we estimate industrial wastewater flows composition using the UN-ISIC classification system?

Although we have extensive datasets on the location and typology of industries, we do not know much on their generated and discharged wastewater. This lack of information compromises the achievement of the sustainable development goals focused on water (Sustainable Development Goal 6) in Europe and globally. Thus, our goal was to assess to which degree the chemical composition of industrial wastewater could be estimated based on the industry's typology according to its International Standard Industrial Classification of All Economic Activities (ISIC) class. We collected wastewater effluent water samples from 60 industrial wastewater effluents (before any wastewater treatment process), accounting for 5 samples each of 12 ISIC classes, analyzed the composition of key contaminants (i.e. European Commission rated priority compounds and watchlist), and statistically assessed the similarities and differences amongst ISIC classes using ordination and random forest analyses. The results showed statistically significant linkages between most ISIC classes and the composition of produced wastewater. Among the analytical parameters measured, the random forest methodology allowed identifying a sub-set particularly relevant for classification or eventual contamination prediction based on ISIC class. This is an important applied research topic with strong management implications to (i) determine pollution emission caps for each individual ISIC class, (ii) define monitoring schemes to sample and analyze industrial wastewater, and (iii) enable predicting pollutant loads discharged in river basins with scarce information. These encouraging results urge us to expand our work into other ISIC classes and water quality parameters to draw a full picture of the relationship between ISIC classes and produced wastewater.

Assessment of degradation byproducts and NDMA formation potential during UV and UV/H2O2 treatment of doxylamine in the presence of monochloramine.

UV-C radiation is the U.S. EPA recommended technology to remove N-nitrosodimethylamine (NDMA) during drinking and recycled water production. Frequently, H(2)O(2) is added to the treatment to remove other recalcitrant compounds and to prevent NDMA reformation. However, the transformation of NDMA precursors during the UV and UV/H(2)O(2) process and the consequences for NDMA formation potential are currently not well understood, in particular in the presence of monochloramine. In this study, doxylamine has been chosen as a model compound to elucidate its degradation byproducts in the UV and UV/H(2)O(2) process and correlate those with changes to the NDMA formation potential. This study shows that during UV treatment in the presence and absence of monochloramine, NDMA formation potential can be halved. However, an increase of more than 30% was observed when hydrogen peroxide was added. Ultrafast liquid chromatography coupled to quadrupole-linear ion trap mass spectrometer was used for screening and structural elucidation of degradation byproducts identifying 21 chemical structures from the original parent compound. This work shows that further oxidation of NDMA precursors does not necessarily lead to a decrease in NDMA formation potential. Degradation byproducts with increased electron density in the vicinity of the dimethylamino moiety, for example induced by hydroxylation, may have a higher yield of nucleophilic substitution and subsequent NDMA formation compared to the parent compound during chloramination. This work demonstrates the need to consider the formation of oxidation byproducts and associated implications for the control and management of NDMA formation in downstream processes and distribution when integrating oxidative treatments into a treatment train generating either drinking water or recycled water for potable reuse.

Effect of UV and UV/H2O2 in the presence of chloramines on NDMA formation potential of tramadol.

This study evaluates the effect of UV-C and UV-C/H(2)O(2) in the presence of chloramines on the N-nitrosodimethylamine formation potential (NDMA FP) of tramadol as a model precursor. The experiments were performed at high initial concentrations of TMDL (i.e., 20 mg/L) in order to elucidate the structures of TMDL byproducts. Twenty-four byproducts were identified in UV-C, UV-C/monochloramine, and UV/H(2)O(2)/monochloramine oxidation of tramadol using MS(3) capabilities of a hybrid quadrupole-linear ion trap mass spectrometer, combined with online hydrogen/deuterium (H/D) exchange experiments. Oxidative cleavage of methoxy and methoxybenzene moiety, O-demethylation, hydroxylation, and cyclohexane ring-opening were identified as major reaction mechanisms of tramadol in UV oxidation. Addition of monochloramine decreased the degradation rates of tramadol and its byproducts and yielded several monochlorinated derivatives. The oxidation rates were significantly enhanced in the presence of H(2)O(2), and byproducts of oxidative benzene ring-opening were detected. The majority of the identified byproducts are likely to have a higher NDMA FP than the parent compound due to a reduced steric hindrance and/or insertion of electron-donating hydroxyl groups in the N,N-dimethylamine side chain. This was confirmed by the results of NDMA FP tests, which showed that the formation of NDMA was enhanced up to four times depending on the process conditions in UV alone and in UV and UV/H(2)O(2) in the presence of monochloramine. Prolonged oxidation by hydroxyl radicals in UV/H(2)O(2)/monochloramine process mineralized some of the byproducts and slightly reduced the NDMA FP at the end of the treatment. The obtained degradation pathway of tramadol allowed the correlation of changes in NDMA FP during oxidation with its major oxidative transformation reactions. This manuscript demonstrates the significance of oxidation byproducts as NDMA precursors and emphasizes the need for their consideration when evaluating the evolution of NDMA FP during oxidative treatment.

Bioanalytical assessment of the formation of disinfection byproducts in a drinking water treatment plant.

Disinfection of drinking water is the most successful measure to reduce water-borne diseases and protect health. However, disinfection byproducts (DBPs) formed from the reaction of disinfectants such as chlorine and monochloramine with organic matter may cause bladder cancer and other adverse health effects. In this study the formation of DBPs through a full-scale water treatment plant serving a metropolitan area in Australia was assessed using in vitro bioanalytical tools, as well as through quantification of halogen-specific adsorbable organic halogens (AOXs), characterization of organic matter, and analytical quantification of selected regulated and emerging DBPs. The water treatment train consisted of coagulation, sand filtration, chlorination, addition of lime and fluoride, storage, and chloramination. Nonspecific toxicity peaked midway through the treatment train after the chlorination and storage steps. The dissolved organic matter concentration decreased after the coagulation step and then essentially remained constant during the treatment train. Concentrations of AOXs increased upon initial chlorination and continued to increase through the plant, probably due to increased chlorine contact time. Most of the quantified DBPs followed a trend similar to that of AOXs, with maximum concentrations observed in the final treated water after chloramination. The mostly chlorinated and brominated DBPs formed during treatment also caused reactive toxicity to increase after chlorination. Both genotoxicity with and without metabolic activation and the induction of the oxidative stress response pathway showed the same pattern as the nonspecific toxicity, with a maximum activity midway through the treatment train. Although measured effects cannot be directly translated to adverse health outcomes, this study demonstrates the applicability of bioanalytical tools to investigate DBP formation in a drinking water treatment plant, despite bioassays and sample preparation not yet being optimized for volatile DBPs. As such, the bioassays are useful as monitoring tools as they provide sensitive responses even at low DBP levels.

N-nitrosodimethylamine and trihalomethane formation and minimisation in Southeast Queensland drinking water.

This study assesses the prevalence of disinfection by-product (DBP) precursors in some Southeast Queensland drinking water sources by conducting formation potential experiments for the four regulated trihalomethanes (THMs), and the potent carcinogen, N-nitrosodimethylamine (NDMA). NDMA formation potentials were consistently low (<5-21 ng/L), and total THM (tTHM) formation potentials were consistently below the Australian Drinking Water Guideline (250 µg/L). NDMA concentration of finished drinking waters was also monitored and found to be <5 ng/L in all cases. The effect of coagulation and advanced oxidation on the formation of NDMA and THMs is also reported. UV/H(2)O(2) pre-treatment was effective in producing water with very low THMs concentrations, and UV irradiation was an effective method for NDMA degradation. H(2)O(2) was not required for the observed NDMA degradation to occur. Coagulation using alum, ferric chloride or poly(diallyldimethylammonium chloride) (polyDADMAC) was ineffective in removing DBPs precursors from the source water studied, irrespective of the low dissolved organic carbon (DOC) and dissolved organic nitrogen (DON) attained. Rather, coagulation with polyDADMAC caused an increase in NDMA formation potential upon chloramination, and all coagulants led to an increased tTHM formation potential upon chlorination due to the high bromide concentration of the source water studied.

Non targeted screening of nitrogen containing disinfection by-products in formation potential tests of river water and subsequent monitoring in tap water samples.

The generation of disinfection by-products during water chlorination is a major concern in water treatment, given the potential health risks that these substances may pose. In particular, nitrogen-containing DBPs are believed to have greater toxicological significance than carbon-based DBPs. Hence, high performance liquid chromatography coupled to high-resolution mass spectrometry (HPLC-HRMS) in positive mode was employed to identify new non-volatile nitrogen containing disinfection by-products (DBPs) and to assess their presence in potable water. Nine water samples were taken in the Llobregat river, in the context of a water reuse trial, near the catchment of a drinking water treatment plant (DWTP) in 2019. River samples were disinfected with chlorine under controlled formation potential tests conditions and analysed with a non-target approach. The peak lists of raw and chlorinated samples were compared exhaustively, resulting in an extensive list of 495 DBPs that include bromine and/or chlorine atoms. 172 of these species were found frequently, in three or more chlorinated samples. The empirical formulae of these DBPs were unambiguously annotated on the basis of accurate m/z measurements, isotopic patterns and common heuristic rules. Most of the annotated species (310) contained bromide, which is consistent with the relatively high bromide content of the Llobregat basin (>0.3 mg/l). Drinking water samples were taken at the outlet of the DWTP during the same sampling period. According to their analysis, a large portion of the DBPs detected after the formation potential tests do not reach real-life drinking water, which suggests that the treatment train successfully removes a significant fraction of DBP precursors. However, 131 DBPs could still be detected in the final product water. A larger sampling was carried in the Barcelona water distribution network, during six consecutive weeks, and it revealed the presence of 78 halogenated DBPs in end-consumer water, most of which were nitrogen-containing. MS/MS fragmentation and retention times were employed to tentatively suggest molecular structure for these recalcitrant DBPs.

Visible-Light Activation of Persulfate or H2O2 by Fe2O3/TiO2 Immobilized on Glass Support for Photocatalytic Removal of Amoxicillin: Mechanism, Transformation Products, and Toxicity Assessment.

Fe2O3/TiO2 nanocomposites were fabricated via a facile impregnation/calcination technique employing different amounts iron (III) nitrate onto commercial TiO2 (P25 Aeroxide). The as-prepared Fe2O3/TiO2 nanocomposites were characterized by X-ray diffraction (XRD), Raman spectroscopy (RS), scanning electron microscopy/energy-dispersive spectroscopy (SEM/EDXS), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller analysis (BET), electron impedance spectroscopy (EIS), photoluminescence spectroscopy (PL), and diffuse reflectance spectroscopy (DRS). As a result, 5% (w/w) Fe2O3/TiO2 achieved the highest photocatalytic activity in the slurry system and was successfully immobilized on glass support. Photocatalytic activity under visible-light irradiation was assessed by treating pharmaceutical amoxicillin (AMX) in the presence and absence of additional oxidants: hydrogen peroxide (H2O2) and persulfate salts (PS). The influence of pH and PS concentration on AMX conversion rate was established by means of statistical planning and response surface modeling. Results revealed optimum conditions of [S2O82-] = 1.873 mM and pH = 4.808; these were also utilized in presence of H2O2 instead of PS in long-term tests. The fastest AMX conversion possessing a zero-order rate constant of 1.51 × 10-7 M·min-1 was achieved with the photocatalysis + PS system. The AMX conversion pathway was established, and the evolution/conversion of formed intermediates was correlated with the changes in toxicity toward Vibrio fischeri. Reactive oxygen species (ROS) scavenging was also utilized to investigate the AMX conversion mechanism, revealing the major contribution of photogenerated h+ in all processes.

Emission of (chlorinated) reclaimed water into a Mediterranean River and its related effects to the dissolved organic matter fingerprint.

High resolution mass spectrometry (HRMS) was used to investigate the dissolved organic matter (DOM) profile of a reclamation water trial performed in the Llobregat River (Spain) during summer 2019. 23 water samples (including tertiary effluents, surface river and drinking water), taken during five sampling campaigns, were analyzed and their van Krevelen diagrams were compared. The reclaimed water fingerprint was substantially different from the natural profile of the river, showing a higher number of heteroatomic signals (i.e. CHON, CHOS and CHONS) and the presence of high-intensity S-containing features. As a result, reclaimed water discharge introduced substantial changes in the signature of the lignin-like and soot-like compositional-spaces of the river DOM fingerprint. However, the effect on the drinking water fingerprint was, ultimately, very limited. Only a limited number of features (up to 34) were detected as exclusively emitted with the reclaimed water. During the second phase of the trial, the tertiary effluent was chlorinated for disinfection purposes. This process triggered the unexpected formation of a myriad of new features along the Llobregat River. Notably, 109 brominated/chlorinated features were detected, probably generated as a consequence of the photochemical decay of the emitted chloramines and their free-radical reaction with DOM, and three of them persisted in the final drinking water. The formation of halogenated species in situ in the Llobregat River entails uncertainty at ecological and water treatment levels and should be studied carefully to fully disclose the risks associated to wastewater effluent disinfection.

Groundwater antibiotic pollution and its relationship with dissolved organic matter: Identification and environmental implications.

The occurrence of veterinary antibiotics and hydro-chemical parameters in eleven natural springs in a livestock production area is evaluated, jointly with the characterization of their DOM fingerprint by Orbitrap HRMS. Tetracycline and sulfonamide antibiotics were ubiquitous in all sites, and they were detected at low ng L-1 concentrations, except for doxycycline, that was present at µg L-1 in one location. DOM analysis revealed that most molecular formulas were CHO compounds (49 %-68 %), with a remarkable percentage containing nitrogen and sulphur (16 %-23 % and 11 %-24 %, respectively). Major DOM components were phenolic and highly unsaturated compounds (~90 %), typical for soil-derived organic matter, while approximately 11 % were unsaturated aliphatic, suggesting that springs may be susceptible to anthropogenic contamination sources. Comparing the DOM fingerprint among sites, the spring showing the most different profile was the one with surface water interaction and characterized by having lower CHO and higher CHOS formulas and aliphatic compounds. Correlations between antibiotics and DOM showed that tetracyclines positively correlate with unsaturated oxygen-rich substances, while sulfonamides relate with aliphatic and unsaturated oxygen-poor compounds. This indicates that the fate of different antibiotics will be controlled by the type of DOM present in groundwater.

Fate of N-nitrosodimethylamine and its precursors during a wastewater reuse trial in the Llobregat River (Spain).

In summer 2019, a full-scale trial was carried out to investigate the effects in drinking water quality when tertiary treated wastewater was discharged into the Llobregat River upstream of the intake of one of the major drinking water treatment plants of Barcelona and its metropolitan area. Two scenarios were investigated, i.e. discharging the reclaimed water with and without chemical disinfection with chlorine. This study investigates the concentration of N-nitrosodimethylamine (NDMA) as the specific disinfection conditions employed in this trial may favor its formation. To this aim, both NDMA and NDMA formation potential, were measured. The river contained NDMA at very low concentrations, but the concentration of NDMA precursors was already high. The NDMA concentration was reduced from discharge to the river to drinking water intake probably due to a combined effect of dilution and photolysis. The formation potential was also reduced probably due to dilution and biodegradation. The concentration of NDMA in the drinking water was always low (<7.3 ng/L), although the formation potential was above 10 ng/L in one sample. Dissolved organic matter characterization by high resolution mass spectrometry revealed differences between the nature of the organic matter in the river before and after reclaimed water discharge.

Monitoring NDMA precursors throughout membrane-based advanced wastewater treatment processes by organic matter fluorescence.

This study investigates the potential of fluorescence excitation/emission matrices (EEM) measurement as a tool to predict N-Nitrosodimethylamine (NDMA) formation in water reuse applications. In particular, samples from a pilot-scale membrane biological reactor (MBR) followed by nanofiltration (NF) advanced water treatment plant, are used for the study. Concentrations of both, specific NDMA precursors and NDMA formation potential (FP) are correlated with different EEM peaks. The specific precursors investigated are: erythromycin, azithromycin, clarithromycin, venlafaxine, o-desmethylvenlafaxine, ranitidine and citalopram, while the NDMA FP is conventionally measured by the NDMA formation potential test. EEM peaks investigated are obtained by fluorescence regional integration as well as by the peak picking method generating I1, I2, I3, I4, and I5 peaks. Results showed that protein-like materials are correlated with the bulk NDMA FP and specific NDMA precursors. Additionally, selected fluorescence peaks such as I1, I2 and I4 are strongly correlated with NDMA precursors throughout the MBR-NF pilot plant. The removal of NDMA precursors and EEM peaks also correlated well (R2 > 0.8). This data shows that fluorescence EEM can be a promising tool to monitor the concentration of NDMA precursors and their removal in water reuse application.

Characterization of organic matter by HRMS in surface waters: Effects of chlorination on molecular fingerprints and correlation with DBP formation potential.

In order to understand and minimize the formation of halogenated disinfection by-products (DBPs), it is important to investigate how dissolved organic matter (DOM) contributes to their generation. In the present study, we analysed the DOM profile of water samples from the Barcelona catchment area by high resolution mass spectrometry (HRMS) and we studied the changes after chlorination. Chlorination produced significant changes in the DOM, decreased the average m/z and Kendrick mass defect (KMD) of their spectra and decreased the number and abundance of lignin-like features. The Van Krevelen (VK) fingerprint exhibited several noticeable changes, including the appearance of highly oxidized peaks in the tannin-like region (average O/C, 0.78 ± 0.08), the appearance of features with low H/C and the disappearance of more than half of the lipids-like features. Up to 657 halogenated peaks were generated during sample chlorination, most of which in the condensed hydrocarbons-like and the lignin-like region of the VK diagram. Around 200 features were found to be strongly correlated (ρ ≥ 0.795) to the formation potential of trihalomethanes (THMs) and 5 were correlated with the formation potential of haloacetonitrile (HANs). They all were plotted in the lignin fraction of the VK diagram, but both groups of features exhibited different nitrogen content: those features related to HANs FP had at least one nitrogen atoms in their structures, whilst those related to THMs did not.

Comparing three Australian natural organic matter isolates to the Suwannee river standard: Reactivity, disinfection by-product yield, and removal by drinking water treatments.

Water treatments that provide efficient removal of organic and inorganic disinfection by-product (DBP) precursors across variable natural organic matter (NOM) sources are desirable. Treatments that effectively remove inorganic DBP precursors such as bromide, which significantly shift the speciation of DBP formation towards more toxic DBPs, are of particular interest and have been less investigated. This study characterised NOM isolated from three major drinking water sources in Southeast Queensland (SEQ), Australia, and compared it to the International Humic Substances Society (IHSS) Suwannee River NOM isolate (SR) in terms of DBP precursor removal treatments and DBP formation. Each NOM isolate was used to make synthetic water samples with otherwise identical water quality parameters, that were treated with enhanced coagulation (EC) or EC followed by; anion exchange (MIEX® resin), powdered activated carbon (PAC), granular activated carbon (GAC) or silver impregnated activated carbon (SIAC), to investigate the removal of DBP precursors (bromide and DOC), minimisation of DBPs, as well as the change in specific chlorine demand. EC/SIAC treatment was the most effective method of DBP control studied, due to the efficient simultaneous NOM and bromide adsorption of the SIAC (99 ±â€¯1% bromide removal regardless of NOM source). This treatment also resulted in >92% removal of each of the measured DBPs across all NOM sources, with the exception of DBAN and 1,1-DCP, which achieved >80% removal across all NOM sources. Increases in tribromomethane (TBM) and dibromoacetonitrile (DBAN) formation were observed after all other treatment/NOM-isolate combinations, due to increased Br:DOC ratio after treatment, whereas chlorinated DBPs were generally well-controlled by all treatment/NOM-isolate combinations. Differences in reactivity of the individual NOM isolates were found to be related to both the origin of the isolate and the treatment employed, however, bromide removal capacity for each treatment was independent of NOM source.

Orbitrap molecular fingerprint of dissolved organic matter in natural waters and its relationship with NDMA formation potential.

N-nitrosodimethylamine (NDMA) is a disinfection byproduct that has been classified as probable human carcinogen by the US Environmental Protection Agency. According to the published literature, natural dissolved organic matter (DOM) can be a source of NDMA precursors in drinking water. New advances in chemical characterization of DOM with high resolution mass spectrometry (HRMS) are allowing researchers to understand these ultra-complex mixtures. The objective of this study is to investigate analytical methodologies based on HRMS to explore NDMA formation from natural waters. To this aim, different waters from drinking water reservoirs in Spain containing NDMA precursors (quantified by means of NDMA formation potential) in concentrations between 17 and 60 ng/L have been studied. The workflow includes DOM solid-phase extraction and Orbitrap analysis with and without chromatographic separation. Here, we show that the molecular composition of DOM across the studied drinking water reservoirs is correlated with the NDMA formation potential. In particular, we found that NDMA formation potential is associated with compounds with high hydrogen saturation (H/C ≥ 1.5), corresponding also to reservoirs with higher background nutrient concentrations and wastewater indicators. Further chromatographic fractionation did not allow better definition of these possible precursors as they were present in different fractions of the chromatogram, suggesting that they were isomerically complex.