RESUMO
Dexterous continuum manipulators (DCMs) can largely increase the reachable region and steerability for minimally and less invasive surgery. Many such procedures require the DCM to be capable of producing large deflections. The real-time control of the DCM shape requires sensors that accurately detect and report large deflections. We propose a novel, large deflection, shape sensor to track the shape of a 35 mm DCM designed for a less invasive treatment of osteolysis. Two shape sensors, each with three fiber Bragg grating sensing nodes is embedded within the DCM, and the sensors' distal ends fixed to the DCM. The DCM centerline is computed using the centerlines of each sensor curve. An experimental platform was built and different groups of experiments were carried out, including free bending and three cases of bending with obstacles. For each experiment, the DCM drive cable was pulled with a precise linear slide stage, the DCM centerline was calculated, and a 2D camera image was captured for verification. The reconstructed shape created with the shape sensors is compared with the ground truth generated by executing a 2D-3D registration between the camera image and 3D DCM model. Results show that the distal tip tracking accuracy is 0.40 ± 0.30 mm for the free bending and 0.61 ± 0.15 mm, 0.93 ± 0.05 mm and 0.23 ± 0.10 mm for three cases of bending with obstacles. The data suggest FBG arrays can accurately characterize the shape of large-deflection DCMs.
RESUMO
Minimally-invasive Osteoporotic Hip Augmentation (OHA) by injecting bone cement is a potential treatment option to reduce the risk of hip fracture. This treatment can significantly benefit from computer-assisted planning and execution system to optimize the pattern of cement injection. We present a novel robotic system for the execution of OHA that consists of a 6-DOF robotic arm and integrated drilling and injection component. The minimally-invasive procedure is performed by registering the robot and preoperative images to the surgical scene using multiview image-based 2D/3D registration with no external fiducial attached to the body. The performance of the system is evaluated through experimental sawbone studies as well as cadaveric experiments with intact soft tissues. In the cadaver experiments, distance errors of 3.28mm and 2.64mm for entry and target points and orientation error of 2.30° are calculated. Moreover, the mean surface distance error of 2.13mm with translational error of 4.47mm is reported between injected and planned cement profiles. The experimental results demonstrate the first application of the proposed Robot-Assisted combined Drilling and Injection System (RADIS), incorporating biomechanical planning and intraoperative fiducial-less 2D/3D registration on human cadavers with intact soft tissues.
RESUMO
BACKGROUND: Augmentation of the proximal femur with bone cement (femoroplasty) has been identified as a potential preventive approach to reduce the risk of fracture. Femoroplasty, however, is associated with a risk of thermal damage as well as the leakage of bone cement or blockage of blood supply when large volumes of cement are introduced inside the bone. METHODS: Six pairs of cadaveric femora were augmented using a newly proposed planning paradigm and an in-house navigation system to control the location and volume of the injected cement. To evaluate the risk of thermal damage, we recorded the peak temperature of bone at three regions of interest as well as the exposure time for temperature rise of 8 °C, 10 °C, and 12 °C in these regions. Augmentation was followed by mechanical testing to failure resembling a sideway fall on the greater trochanter. FINDINGS: Results of the fracture tests correlated with those of simulations for the yield load (R2 = 0.77) and showed that femoroplasty can significantly improve the yield load (42%, P < 0.001) and yield energy (139%, P = 0.062) of the specimens. Meanwhile, temperature recordings of the bone surface showed that the areas close to the greater trochanter will be exposed to more critical temperature rise than the trochanteric crest and femoral neck areas. INTERPRETATION: The new planning paradigm offers a more efficient injection strategy with injection volume of 9.1 ml on average. Meanwhile, temperature recordings of bone surfaces suggest that risk of thermal necrosis remains as a concern with femoroplasty using Polymethylmethacrylate.
Assuntos
Cimentos Ósseos , Polimetil Metacrilato , Fenômenos Biomecânicos , Cimentos Ósseos/uso terapêutico , Colo do Fêmur , Humanos , TemperaturaRESUMO
Femoroplasty is a proposed alternative therapeutic method for preventing osteoporotic hip fractures in the elderly. Previously developed navigation system for femoroplasty required the attachment of an external X-ray fiducial to the femur. We propose a fiducial-free 2D/3D registration pipeline using fluoroscopic images for robot-assisted femoroplasty. Intraoperative fluoroscopic images are taken from multiple views to perform registration of the femur and drilling/injection device. The proposed method was tested through comprehensive simulation and cadaveric studies. Performance was evaluated on the registration error of the femur and the drilling/injection device. In simulations, the proposed approach achieved a mean accuracy of 1.26±0.74 mm for the relative planned injection entry point; 0.63±0.21° and 0.17±0.19° for the femur injection path direction and device guide direction, respectively. In the cadaver studies, a mean error of 2.64 ± 1.10 mm was achieved between the planned entry point and the device guide tip. The biomechanical analysis showed that even with a 4 mm translational deviation from the optimal injection path, the yield load prior to fracture increased by 40.7%. This result suggests that the fiducial-less 2D/3D registration is sufficiently accurate to guide robot assisted femoroplasty.
RESUMO
A potential effective treatment for prevention of osteoporotic hip fractures is augmentation of the mechanical properties of the femur by injecting it with bone cement. This therapy, however, is only in research stage and can benefit substantially from computational simulations to optimize the pattern of cement injection. Some studies have considered a patient-specific planning paradigm for Osteoporotic Hip Augmentation (OHA). Despite their biomechanical advantages, customized plans require advanced surgical systems for implementation. Other studies, therefore, have suggested a more generalized injection strategy. The goal of this study is to investigate as to whether the additional computational overhead of the patient-specific planning can significantly improve the bone strength as compared to the generalized injection strategies attempted in the literature. For this purpose, numerical models were developed from high resolution CT images (nâ¯=â¯4). Through finite element analysis and hydrodynamic simulations, we compared the biomechanical efficiency of the customized cement-based augmentation along with three generalized injection strategies developed previously. Two series of simulations were studied, one with homogeneous and one with inhomogeneous material properties for the osteoporotic bone. The customized cement-based augmentation inhomogeneous models showed that injection of only 10â¯ml of bone cement can significantly increase the yield load (79.6%, Pâ¯<â¯0.01) and yield energy (199%, Pâ¯<â¯0.01) of an osteoporotic femur. This increase is significantly higher than those of the generalized injections proposed previously (23.8% on average). Our findings suggest that OHA can significantly benefit from a patient-specific plan that determines the pattern and volume of the injected cement.
Assuntos
Cimentos Ósseos/uso terapêutico , Fraturas do Quadril/prevenção & controle , Fraturas por Osteoporose/prevenção & controle , Modelagem Computacional Específica para o Paciente , Polimetil Metacrilato/administração & dosagem , Fenômenos Biomecânicos , Osso e Ossos , Feminino , Fêmur/cirurgia , Análise de Elementos Finitos , Articulação do Quadril/diagnóstico por imagem , Humanos , Masculino , Modelos Teóricos , Tomografia Computadorizada por Raios XRESUMO
In this study, we aim to create and validate a Finite Element (FE) model to estimate the bone temperature after cement injection and compare the simulation temperature results with experimental data in three key locations of the proximal femur. Simulation results suggest that the maximum temperature-rise measured at the bone surface is 10°C which occurs about 12 minutes after the injection. Temperature profiles measured during the experiment showed an agreement with those of the simulation with an average error of 1.73°C Although additional experiments are required to further validate the model, results of this study suggest that this model is a promising tool for bone augmentation planning to lower the risk of thermal necrosis.
RESUMO
OBJECTIVES: To compare the results of a simulated fall on the greater trochanter in the proximal portion of a synthetic femur before and after femoral reinforcement with tricalcium phosphate bone cement (TP) and polymethyl methacrylate (PMMA), using finite element analysis (FEA). METHODS: Using two synthetic proximal femurs, a FEA simulating a fall on the greater trochanter was performed, using the Bi-directional Evolutionary Structural Optimization (BESO) program. For this analysis, the femurs were filled with TP and PMMA after perforations were created in the trochanteric region and neck. The results were compared with the strength values obtained from testing the control specimen, a synthetic bone without reinforcement. RESULTS: FEA showed a value of 600 N prior to reinforcement. After cementing with PMMA, the load increased by 57.5% (945 N), and by 53% (920 N) after cementing with TP. CONCLUSION: Synthetic femurs gained resistance to fracture-causing forces in a simulated fall on the trochanter after bone reinforcement with PMMA and TP. Level of Evidence III; Experimental study.
OBJETIVOS: Avaliar, com o método de elementos finitos (EF), os resultados obtidos com a simulação de queda sobre o trocanter maior, usando a porção proximal de um fêmur sintético, com a finalidade de comparar os valores obtidos antes e após técnica de reforço femoral com cimento de fosfato tricálcico (FT) e polimetilmetacrilato (PMMA). MÉTODOS: Utilizando dois fêmures proximais sintéticos, foi realizada a análise de elementos finitos, simulando queda sobre o trocanter maior com o programa Bi-directional Evolutionary Structural Optimization (BESO). Para essa análise, os fêmures foram preenchidos, após a realização de pertuitos na região trocantérica e no colo, com FT e PMMA e os resultados foram comparados com a força obtida na análise do corpo de prova controle, osso sintético sem preenchimento. RESULTADOS: Comparando a análise de elementos finitos antes do reforço femoral, obteve-se o valor de 600 N. Depois da cimentação com PMMA, foi observado um aumento na carga máxima da ordem de 57,5% (945 N) e de 53% (920 N) com o FT. CONCLUSÃO: Os fêmures sintéticos ganharam resistência aos fatores causadores de fratura em queda simulada sobre o trocanter depois do reforço ósseo com PMMA e cimento de FT. Nível de Evidência III; Estudo experimental.
RESUMO
PURPOSE: Patient-specific musculoskeletal biomechanical simulation is useful in preoperative surgical planning and postoperative assessment in orthopedic surgery and rehabilitation medicine. A difficulty in application of the patient-specific musculoskeletal modeling comes from the fact that the muscle attachment regions are typically invisible in CT and MRI. Our purpose is to develop a method for estimating patient-specific muscle attachment regions from 3D medical images and to validate with cadaver experiments. METHODS: Eight fresh cadaver specimens of the lower extremity were used in the experiments. Before dissection, CT images of all the specimens were acquired and the bone regions in CT images were extracted using an automated segmentation method to reconstruct the bone shape models. During dissection, ten different muscle attachment regions were recorded with an optical motion tracker. Then, these regions obtained from eight cadavers were integrated on an average bone surface via non-rigid registration, and muscle attachment probabilistic atlases (PAs) were constructed. An average muscle attachment region derived from the PA was non-rigidly mapped to the patients bone surface to estimate the patient-specific muscle attachment region. RESULTS: Average Dice similarity coefficient between the true and estimated attachment areas computed by the proposed method was more than 10% higher than the one computed by a previous method in most cases and the average boundary distance error of the proposed method was 1.1 mm smaller than the previous method on average. CONCLUSION: We conducted cadaver experiments to measure the attachment regions of the hip muscles and constructed PAs of the muscle attachment regions. The muscle attachment PA clarified the variations of the location of the muscle attachments and allowed us to estimate the patient-specific attachment area more accurately based on the patient bone shape derived from CT.
Assuntos
Quadril/diagnóstico por imagem , Imageamento Tridimensional/métodos , Imageamento por Ressonância Magnética/métodos , Músculo Esquelético/diagnóstico por imagem , Tomografia Computadorizada por Raios X/métodos , Idoso , Algoritmos , Fenômenos Biomecânicos , Cadáver , Feminino , Humanos , Masculino , Pessoa de Meia-Idade , Movimento (Física) , Reconhecimento Automatizado de Padrão , Probabilidade , Reprodutibilidade dos TestesRESUMO
Shape sensing techniques utilizing Fiber Bragg grating (FBG) arrays can enable real-time tracking and control of dexterous continuum manipulators (DCM) used in minimally invasive surgeries. For many surgical applications, the DCM may need to operate with much larger curvatures than what current shape sensing methods can detect. This paper proposes a novel shape sensor, which can detect a radius of curvature of 15 mm for a 35 mm long DCM. For this purpose, we used FBG sensors along with nitinol wires as the supporting substrates to form a triangular cross section. For verification, we assembled the sensor inside the wall of the DCM. Experimental results indicate that the proposed sensor can detect the DCM's curvature with an average error of 3.14%.
RESUMO
ABSTRACT Objectives: To compare the results of a simulated fall on the greater trochanter in the proximal portion of a synthetic femur before and after femoral reinforcement with tricalcium phosphate bone cement (TP) and polymethyl methacrylate (PMMA), using finite element analysis (FEA). Methods: Using two synthetic proximal femurs, a FEA simulating a fall on the greater trochanter was performed, using the Bi-directional Evolutionary Structural Optimization (BESO) program. For this analysis, the femurs were filled with TP and PMMA after perforations were created in the trochanteric region and neck. The results were compared with the strength values obtained from testing the control specimen, a synthetic bone without reinforcement. Results: FEA showed a value of 600 N prior to reinforcement. After cementing with PMMA, the load increased by 57.5% (945 N), and by 53% (920 N) after cementing with TP. Conclusion: Synthetic femurs gained resistance to fracture-causing forces in a simulated fall on the trochanter after bone reinforcement with PMMA and TP. Level of Evidence III; Experimental study.
RESUMO Objetivos: Avaliar, com o método de elementos finitos (EF), os resultados obtidos com a simulação de queda sobre o trocanter maior, usando a porção proximal de um fêmur sintético, com a finalidade de comparar os valores obtidos antes e após técnica de reforço femoral com cimento de fosfato tricálcico (FT) e polimetilmetacrilato (PMMA). Métodos: Utilizando dois fêmures proximais sintéticos, foi realizada a análise de elementos finitos, simulando queda sobre o trocanter maior com o programa Bi-directional Evolutionary Structural Optimization (BESO). Para essa análise, os fêmures foram preenchidos, após a realização de pertuitos na região trocantérica e no colo, com FT e PMMA e os resultados foram comparados com a força obtida na análise do corpo de prova controle, osso sintético sem preenchimento. Resultados: Comparando a análise de elementos finitos antes do reforço femoral, obteve-se o valor de 600 N. Depois da cimentação com PMMA, foi observado um aumento na carga máxima da ordem de 57,5% (945 N) e de 53% (920 N) com o FT. Conclusão: Os fêmures sintéticos ganharam resistência aos fatores causadores de fratura em queda simulada sobre o trocanter depois do reforço ósseo com PMMA e cimento de FT. Nível de Evidência III; Estudo experimental.