RESUMO
Objective: To determine the frequency of various hematological manifestations among newly diagnosed cases of pulmonary tuberculosis on complete blood counts. Methods: This retrospective cross-sectional study was conducted on 500 newly diagnosed patients of pulmonary tuberculosis in hematology department of Nishtar Medical University from 1st November 2020 to 30th April 2021 using consecutive sampling. Detailed history and complete general physical examination findings, complete blood picture including erythrocyte sedimentation rate were retrieved from hospital electronic medical records system. Data was collected on a specially designed Proforma, entered into SPSS version 23.0 and analyzed. Data is presented as mean±SD and frequency and percentages for numerical and categorical variables respectively using tables and figures. Results: In this study the mean age of patients was 34.36 ± 6.41 years with male to female ratio 2.52: 1. Frequency of anemia was 82.6% (n=413), leukocytosis was 46.2% (n=231) and leucopenia in 102 patients (20.4%). Thrombocytosis was detected in 131(26.2%) patients. Raised ESR was observed in 495(99%) of the patients. No association of age and gender was observed with hematological manifestations. However, thrombocytosis was significantly more common in male patients (p-value = 0. 008). Conclusion: Hematological parameters like high Erythrocyte Sedimentation Rate (ESR) and anemia were commonly detected in newly diagnosed patients with pulmonary tuberculosis. Thrombocytosis was seen more commonly in male patients of pulmonary tuberculosis.
RESUMO
Two-dimensional (2D) materials such as MXenes have attracted considerable attention owing to their enormous potential for structural flexibility. Here, we prepared a Mo2TiC2Tx-layered structure from parent Mo2TiAlC2Tx MAX by chemically selective etching of the aluminum layer. The prepared MXene was employed in composite formation with CTAB-grafted multiwalled carbon nanotubes (MWCNTs) to have a structure with improved electrochemical performance. The samples were characterized to analyze the structure, morphology, elemental detection, vibrational modes, and surface chemistry, followed by an electrochemical performance of the Mo2TiC2Tx MXene and MWCNTs@Mo2TiC2Tx composite using the GAMRAY Potentiostat under a 1 M KOH electrolyte. The specific capacitance of pristine Mo2TiC2Tx was 425 F g-1, which was enhanced to 1740 F g-1 (almost 4 times) at 5 mV s-1 due to the increase in active surface area and conductive paths between the MXene sheets. The charge storage mechanism was studied by further resolving the cyclic voltammograms. MWCNTs@Mo2TiC2Tx showed much improved electrochemical performance and reaction kinetics, making it an ideal material candidate for supercapacitor applications.
RESUMO
Because of a rapidly growing need for water, it is essential to find new fast and reliable ways of water purification from organic pollutants. For removing organic azo dyes from water, various catalysts and photocatalysts have been designed to meet crucial water needs. In this study tin (Sn) doped bismuth ferrite (BFO) nanoparticles have been synthesized using the sol-gel technique. Further, BFSO/GNP nanohybrids were synthesized by mixing BFSO nanoparticles with graphene nanoplatelets (GNPs) via a simple and cost effective coprecipitation process. XRD and SEM showed that BFSO/GNP nanohybrids are well grown in crystal structure along with uniform and homogeneous morphology. XPS supported the elemental composition and interface bonding of both materials present inside the nanohybrids. DRS and catalytic activities showed that BFSO/GNP nanohybrids are both dark and light active species for performing dye degradation activities during water purification. The as-synthesized nanohybrids provided efficient dye removal from water even in the absence of light owing to the presence of defects and trap-state carriers (electrons) inside the graphene sheets. The optimized nanohybrid BFSO-15/GNP showed 100% dye removal in 60 min with 90% catalytic activity under dark. The recyclability test showed stable and repeatable performance of BFSO/GNP nanohybrids up to 10 cycles of catalytic activities.
RESUMO
Two-dimensional (2D) materials have been studied as an emerging class of nanomaterials owing to their attractive properties in nearly every field of science and technology. Molybdenum disulfide (MoS2) is one of the more promising candidates of these atomically thin 2D materials for its technological potential. The facile synthesis of MoS2 remains a matter of broad interest. In this study, MoS2 was synthesized by chemical vapor deposition sulfurization at various temperatures (550 °C, 650 °C, and 750 °C) of either precursor molybdenum metal (Mo) or molybdenum trioxide (MoO3) deposited on silicon/silicon dioxide (Si/SiO2) via e-beam evaporation. Monolayer, bilayer, and few layers sulfurized samples have been grown and verified by Raman, photoluminescence spectroscopy, XRD, XPS, and AFM. MoO3 sulfurization provided monolayer growth in comparison to Mo sulfurization under the same conditions and precursor thicknesses. Optical microscopy showed the homogeneous nature of grown samples. A main finding of this work is that MoO3 sulfurization produced higher quality MoS2 as compared to those grown by an Mo precursor. Device characteristics based on monolayer MoO3 sulfurized MoS2-x include nonvolatile resistive switching with Ion/Ioff ≈ 104 at a relatively low operating bias of ±1 V. In addition, field-effect transistor characteristics revealed p-type material growth with a carrier mobility â¼ 41 cm2 V-1 s-1, which is in contrast to typically observed n-type characteristics.
RESUMO
Development of efficient visible light photocatalysts for water purification and hydrogen production by water splitting has been quite challenging. The activities of visible light photocatalysts are generally controlled by the extent of absorption of incident light, band gap, exposure of catalyst surface to incident light and adsorbing species. Here, we have synthesized nanostructured, La and Se co-doped bismuth ferrite (BLFSO) nanosheets using double solvent sol-gel and co-precipitation methods. Structural analysis revealed that the La and Se co-doped BFO i.e. Bi0.92La0.08Fe1-x Se x O3 (BLFSO) transformed from perovskite rhombohedral to orthorhombic phase. As a result of co-doping and phase transition, a significant decrease in the band gap from 2.04 eV to 1.76 eV was observed for BLFSO-50% (having Se doping of 50%) which requires less energy during transfer of electrons from the valence to the conduction band and ultimately enhances the photocatalytic activity. Moreover, upon increase in Se doping, the BLFSO morphology gradually changed from particles to nanosheets. Among various products, BLFSO-50% exhibited the highest photocatalytic activities under visible light owing to homogenous phase distribution, regular sheet type morphology and larger contact with dye containing solutions. In summary, La, Se co-doping is an effective approach to tune the electronic structure of photocatalysts for visible light photocatalysis.