High-Pressure-Sintering-Induced Microstructural Engineering for an Ultimate Phonon Scattering of Thermoelectric Half-Heusler Compounds.

Thermal management is of vital importance in various modern technologies such as portable electronics, photovoltaics, and thermoelectric devices. Impeding phonon transport remains one of the most challenging tasks for improving the thermoelectric performance of certain materials such as half-Heusler compounds. Herein, a significant reduction of lattice thermal conductivity (κL ) is achieved by applying a pressure of ≈1 GPa to sinter a broad range of half-Heusler compounds. Contrasting with the common sintering pressure of less than 100 MPa, the gigapascal-level pressure enables densification at a lower temperature, thus greatly modifying the structural characteristics for an intensified phonon scattering. A maximum κL reduction of ≈83% is realized for HfCoSb from 14 to 2.5 W m-1 K-1 at 300 K with more than 95% relative density. The realized low κL originates from a remarkable grain-size refinement to below 100 nm together with the abundant in-grain defects, as determined by microscopy investigations. This work uncovers the phonon transport properties of half-Heusler compounds under unconventional microstructures, thus showing the potential of high-pressure compaction in advancing the performance of thermoelectric materials.

Fully sp2 -Carbon-Linked Crystalline Two-Dimensional Conjugated Polymers: Insight into 2D Poly(phenylenecyanovinylene) Formation and its Optoelectronic Properties.

Cyano-substituted polyphenylene vinylenes (PPVs) have been the focus of research for several decades owing to their interesting optoelectronic properties and potential applications in organic electronics. With the advent of organic two-dimensional (2D) crystals, the question arose as to how the chemical and optoelectronic advantages of PPVs evolve in 2D compared with their linear counterparts. In this work, we present the efficient synthesis of two novel 2D fully sp2 -carbon-linked crystalline PPVs and investigate the essentiality of inorganic bases for their catalytic formation. Notably, among all bases screened, cesium carbonate (Cs2 CO3 ) plays a crucial role and enables reversibility in the first step with subsequent structure locking by formation of a C=C double bond to maintain crystallinity, which is supported by density functional theory (DFT) calculations. A quantifiable energy diagram of a "quasi-reversible reaction" is proposed, which allows the identification of further suitable C-C bond formation reactions for 2D polymerizations. Moreover, the narrowing of the HOMO-LUMO gap is delineated by expanding the conjugation into two dimensions. To enable environmentally benign processing, the post-modification of 2D PPVs is further performed, which renders stable dispersions in the aqueous phase.

Synthesis, Characterization, and Electrochemistry of Layered Chalcogenides LiCu Ch ( Ch = Se, Te).

Two novel compounds, LiCu Ch ( Ch = Se or Te), were synthesized by direct reaction between elements in closed ampules inside corundum crucibles. Both compounds are highly air-sensitive and possess an anti-PbClF crystal structure, which contains Cu Ch layer analogues to the Fe[As/Se] layers in Fe-based superconductors. In electrochemical battery cells, Li can be almost completely extracted from LiCuSe, but the reverse reaction is only partly successful and Li2Se and Cu2- xSe are formed instead. LiCuSe exhibits a temperature independent and slightly positive magnetic susceptibility. From 7Li NMR measurements, the activation energy of the Li ion diffusion process is about 0.5 eV but is slightly lower for LiCuTe as compared to LiCuSe. Also, the small and almost temperature independent NMR shifts of the 7Li nucleus indicate the absence of Pauli paramagnetism in these compounds, consistent with a 3 d10 full valence state of the Cu ions.

Alloying Behavior of Self-Assembled Noble Metal Nanoparticles.

The atomic redistribution processes occurring in multiparticle nanostructures are hardly understood. To obtain a more detailed insight, we applied high-resolution microscopic, diffraction and spectroscopic characterization techniques to investigate the fine structure and elemental distribution of various bimetallic aerogels with 1:1 compositions, prepared by self-assembly of single monometallic nanoparticles. The system Au-Ag exhibited a complete alloy formation, whereas Pt-Pd aerogels formed a Pd-based network with embedded Pt particles. The assembly of Au and Pd nanoparticles resulted in a Pd-shell formation around the Au particles. This work confirms that bimetallic aerogels are subject to reorganization processes during their gel formation.

Layered-to-Tunnel Structure Transformation and Oxygen Redox Chemistry in LiRhO2 upon Li Extraction and Insertion.

Layered Li(M,Li)O2 (where M is a transition metal) ordered rock-salt-type structures are used in advanced metal-ion batteries as one of the best hosts for the reversible intercalation of Li ions. Besides the conventional redox reaction involving oxidation/reduction of the M cation upon Li extraction/insertion, creating oxygen-located holes because of the partial oxygen oxidation increases capacity while maintaining the oxidized oxygen species in the lattice through high covalency of the M-O bonding. Typical degradation mechanism of the Li(M,Li)O2 electrodes involves partially irreversible M cation migration toward the Li positions, resulting in gradual capacity/voltage fade. Here, using LiRhO2 as a model system (isostructural and isoelectronic to LiCoO2), for the first time, we demonstrate an intimate coupling between the oxygen redox and M cation migration. A formation of the oxidized oxygen species upon electrochemical Li extraction coincides with transformation of the layered Li1-xRhO2 structure into the γ-MnO2-type rutile-ramsdellite intergrowth LiyRh3O6 structure with rutile-like [1 × 1] channels along with bigger ramsdellite-like [2 × 1] tunnels through massive and concerted Rh migration toward the empty positions in the Li layers. The oxidized oxygen dimers with the O-O distances as short as 2.26 Å are stabilized in this structure via the local Rh-O configuration reminiscent to that in the µ-peroxo-µ-hydroxo Rh complexes. The LiyRh3O6 structure is remarkably stable upon electrochemical cycling illustrating that proper structural implementation of the oxidized oxygen species can open a pathway toward deliberate employment of the anion redox chemistry in high-capacity/high-voltage positive electrodes for metal-ion batteries.

SEI-component formation on sub 5 nm sized silicon nanoparticles in Li-ion batteries: the role of electrode preparation, FEC addition and binders.

Silicon is a promising negative electrode for secondary lithium-based batteries, but the electrochemical reversibility of particularly nanostructured silicon electrodes drastically depends on their interfacial characteristics, commonly known as the solid electrolyte interface (SEI). The beneficial origin of certain electrolyte additives or different binders is still discussed controversially owing to the challenging peculiarities of interfacial post-mortem investigations of electrodes. In this work, we address the common difficulties of SEI investigations of porous silicon/carbon nanostructures and study the addition of a fluoroethylene carbonate (FEC) as a stabilizing additive as well as the use of two different binders, carboxymethyl cellulose/styrene-butadiene rubber (CMC/SBR) and polyacrylic acid (PAA), for the SEI formation. The electrode is composed of silicon nanocrystallites below 5 nm diameter allowing a detailed investigation of interfacial characteristics of silicon owing to the high surface area. We first performed galvanostatic long-term cycling (400 times) and carried out comprehensive ex situ characterization of the cycled nanocrystalline silicon electrodes with XRD, EDXS, TEM and XPS. We modified the preparation of the electrode for post-mortem characterization to distinguish between electrolyte components and the actual SEI. The impact of the FEC additive and two different binders on the interfacial layer is studied and the occurrence of diverse compounds, in particular LiF, Li2O and phosphates, is discussed. These results help to understand general issues in SEI formation and to pave the way for the development of advanced electrolytes allowing for a long-term performance of nanostructured Si-based electrodes.

Inherent Antibacterial Properties of Biodegradable FeMnC(Cu) Alloys for Implant Application.

Implant-related infections or inflammation are one of the main reasons for implant failure. Therefore, different concepts for prevention are needed, which strongly promote the development and validation of improved material designs. Besides modifying the implant surface by, for example, antibacterial coatings (also implying drugs) for deterring or eliminating harmful bacteria, it is a highly promising strategy to prevent such implant infections by antibacterial substrate materials. In this work, the inherent antibacterial behavior of the as-cast biodegradable Fe69Mn30C1 (FeMnC) alloy against Gram-negative Pseudomonas aeruginosa and Escherichia coli as well as Gram-positive Staphylococcus aureus is presented for the first time in comparison to the clinically applied, corrosion-resistant AISI 316L stainless steel. In the second step, 3.5 wt % Cu was added to the FeMnC reference alloy, and the microbial corrosion as well as the proliferation of the investigated bacterial strains is further strongly influenced. This leads for instance to enhanced antibacterial activity of the Cu-modified FeMnC-based alloy against the very aggressive, wild-type bacteria P. aeruginosa. For clarification of the bacterial test results, additional analyses were applied regarding the microstructure and elemental distribution as well as the initial corrosion behavior of the alloys. This was electrochemically investigated by a potentiodynamic polarization test. The initial degraded surface after immersion were analyzed by glow discharge optical emission spectrometry and transmission electron microscopy combined with energy-dispersive X-ray analysis, revealing an increase of degradation due to Cu alloying. Due to their antibacterial behavior, both investigated FeMnC-based alloys in this study are attractive as a temporary implant material.

Influence of magnetic field on electron beam-induced Coulomb explosion of gold microparticles in transmission electron microscopy.

In this work we instigated the fragmentation of Au microparticles supported on a thin amorphous carbon film by irradiating them with a gradually convergent electron beam inside the Transmission Electron Microscope. This phenomenon has been generically labeled as "electron beam-induced fragmentation" or EBIF and its physical origin remains contested. On the one hand, EBIF has been primarily characterized as a consequence of beam-induced heating. On the other, EBIF has been attributed to beam-induced charging eventually leading to Coulomb explosion. To test the feasibility of the charging framework for EBIF, we instigated the fragmentation of Au particles under two different experimental conditions. First, with the magnetic objective lens of the microscope operating at full capacity, i.e. background magnetic field B=2 T, and with the magnetic objective lens switched off (Lorenz mode), i.e. B=0 T. We observe that the presence or absence of the magnetic field noticeably affects the critical current density at which EBIF occurs. This strongly suggests that magnetic field effects play a crucial role in instigating EBIF on the microparticles. The dependence of the value of the critical current density on the absence or presence of an ambient magnetic field cannot be accounted for by the beam-induced heating model. Consequently, this work presents robust experimental evidence suggesting that Coulomb explosion driven by electrostatic charging is the root cause of EBIF.

Hydrothermal carbon-based nanostructured hollow spheres as electrode materials for high-power lithium-sulfur batteries.

Carbon hollow spheres were produced using a sustainable approach, i.e. hydrothermal carbonization, using monosaccharides as carbon precursors and silica nanoparticles as hard-templates. Hydrothermal carbonization is an eco-efficient and cost-effective route to synthesize nanostructured carbonaceous materials from abundant biomass-derived molecules. After further thermal treatment under an inert atmosphere and removal of the silica-based core by chemical etching, porous hollow spheres depicting 5-8 nm thin shells were obtained. Subsequently, carbon-sulfur composites were synthesized via a melt diffusion method and used as nanostructured composites for cathodes in lithium-sulfur (Li-S) cells. The morphology of the hollow spheres was controlled and optimized to achieve improved electrochemical properties. Both high specific energies and high specific powers were obtained, due to the unique nanostructure of the hollow spheres. These results revealed that using optimized carbonaceous materials, it is possible to design sustainable Li-S cells showing promising electrochemical properties.

A Newly Designed High-Strength Tool Steel with High Wear and Corrosion Resistance.

In this study, a newly developed high-strength cast Fe81Cr15V3C1 (wt%) steel with a high resistance against dry abrasion and chloride-induced pitting corrosion is presented. The alloy was synthesized through a special casting process that yielded high solidification rates. The resulting fine, multiphase microstructure is composed of martensite, retained austenite and a network of complex carbides. This led to a very high compressive strength (>3800 MPa) and tensile strength (>1200 MPa) in the as-cast state. Furthermore, a significantly higher abrasive wear resistance in comparison to the conventional X90CrMoV18 tool steel was determined for the novel alloy under very harsh wear conditions (SiC, α-Al2O3). Regarding the tooling application, corrosion tests were conducted in a 3.5 wt.% NaCl solution. Potentiodynamic polarization curves demonstrated a similar behavior during the long-term testing of Fe81Cr15V3C1 and the X90CrMoV18 reference tool steel, though both steels revealed a different nature of corrosion degradation. The novel steel is less susceptible to local degradation, especially pitting, due to the formation of several phases that led to the development of a less dangerous form of destruction: galvanic corrosion. In conclusion, this novel cast steel offers a cost- and resource-efficient alternative to conventionally wrought cold-work steels, which are usually required for high-performance tools under highly abrasive as well as corrosive conditions.

Fast and selective sugar conversion to alkyl lactate and lactic acid with bifunctional carbon-silica catalysts.

A novel catalyst design for the conversion of mono- and disaccharides to lactic acid and its alkyl esters was developed. The design uses a mesoporous silica, here represented by MCM-41, which is filled with a polyaromatic to graphite-like carbon network. The particular structure of the carbon-silica composite allows the accommodation of a broad variety of catalytically active functions, useful to attain cascade reactions, in a readily tunable pore texture. The significance of a joint action of Lewis and weak Brønsted acid sites was studied here to realize fast and selective sugar conversion. Lewis acidity is provided by grafting the silica component with Sn(IV), while weak Brønsted acidity originates from oxygen-containing functional groups in the carbon part. The weak Brønsted acid content was varied by changing the amount of carbon loading, the pyrolysis temperature, and the post-treatment procedure. As both catalytic functions can be tuned independently, their individual role and optimal balance can be searched for. It was thus demonstrated for the first time that the presence of weak Brønsted acid sites is crucial in accelerating the rate-determining (dehydration) reaction, that is, the first step in the reaction network from triose to lactate. Composite catalysts with well-balanced Lewis/Brønsted acidity are able to convert the trioses, glyceraldehyde and dihydroxyacetone, quantitatively into ethyl lactate in ethanol with an order of magnitude higher reaction rate when compared to the Sn grafted MCM-41 reference catalyst. Interestingly, the ability to tailor the pore architecture further allows the synthesis of a variety of amphiphilic alkyl lactates from trioses and long chain alcohols in moderate to high yields. Finally, direct lactate formation from hexoses, glucose and fructose, and disaccharides composed thereof, sucrose, was also attempted. For instance, conversion of sucrose with the bifunctional composite catalyst yields 45% methyl lactate in methanol at slightly elevated reaction temperature. The hybrid catalyst proved to be recyclable in various successive runs when used in alcohol solvent.

Approach to Estimate the Phase Formation and the Mechanical Properties of Alloys Processed by Laser Powder Bed Fusion via Casting.

A high-performance tool steel with the nominal composition Fe85Cr4Mo8V2C1 (wt%) was processed by three different manufacturing techniques with rising cooling rates: conventional gravity casting, centrifugal casting and an additive manufacturing process, using laser powder bed fusion (LPBF). The resulting material of all processing routes reveals a microstructure, which is composed of martensite, austenite and carbides. However, comparing the size, the morphology and the weight fraction of the present phases, a significant difference of the gravity cast samples is evident, whereas the centrifugal cast material and the LPBF samples show certain commonalities leading finally to similar mechanical properties. This provides the opportunity to roughly estimate the mechanical properties of the material fabricated by LPBF. The major benefit arises from the required small material quantity and the low resources for the preparation of samples by centrifugal casting in comparison to the additive manufacturing process. Concluding, the present findings demonstrate the high attractiveness of centrifugal casting for the effective material screening and hence development of novel alloys adapted to LPBF-processing.

Synthesis of micro- and nanosheets of CrCl3-RuCl3 solid solution by chemical vapour transport.

Solid solutions of 2D transition metal trihalides are rapidly growing in interest for the search for new 2D materials with novel properties at nanoscale dimensions. In this regard, we present a synthesis method for the Cr1-xRuxCl3 solid solution and describe the behaviour of the unit cell parameters over the whole composition range, which in general follows Vegard's law in the range of a = 5.958(6)CrCl3 … 5.9731(5)RuCl3 Å, b = 10.3328(20)CrCl3 … 10.34606(21)RuCl3 Å, c = 6.110(5)CrCl3 … 6.0385(5)RuCl3 Å and ß = 108.522(15)CrCl3 … 108.8314(14)RuCl3 °. The synthesized solid solution powder was subsequently used to deposit micro- and nanosheets directly on a substrate by applying chemical vapour transport in a temperature gradient of 575 °C → 525 °C for 2 h and 650 °C → 600 °C for 0.5 h as a bottom-up approach without the need for an external transport agent. The observed chromium chloride enrichment of the deposited crystals is predicted by thermodynamic simulation. The results allow for a nanostructure synthesis of this solid solution with a predictable composition down to about 30 nm in height and lateral size of several µm. When applying a quick consecutive delamination step, it is possible to obtain few- and monolayer structures, which could be used for further studies of downscaling effects for the CrCl3-RuCl3 solid solution. X-ray photoelectron spectroscopy, transmission electron microscopy and Raman spectroscopy were used to confirm the purity and quality of the synthesized crystals.

Direct observation of molecular-level template action leading to self-assembly of a porous framework.

The molecular steps involved in the self-assembly of Cu(3)(BTC)(2) (BTC=1,3,5-benzenetricarboxylic acid) metal-organic frameworks that enclose Keggin-type H(3)PW(12)O(40) heteropolyacid molecules were unraveled by using solution (17)O, (31)P, and (183)W NMR spectroscopy, small-angle X-ray scattering, near-IR spectroscopy, and dynamic light scattering. In aqueous solution, complexation of Cu(2+) ions with Keggin-type heteropolyacids was observed. Cu(2+) ions are arranged around the Keggin structure so that linking through benzenetricarboxylate groups results in the formation of the Cu(3)(BTC)(2) MOF structure HKUST-1. This is a unique instance in which a templating mechanism that relies on specific molecular-level matching and leads to explicit nanoscale building units can be observed in situ during formation of the synthetic nanoporous material.

Highly Efficient Multicomponent Gel Biopolymer Binder Enables Ultrafast Cycling and Applicability in Diverse Battery Formats.

Electrode materials with a high performance and stable cycling have been commercialized, but the utilization of state-of-the-art Li-ion batteries in high-current rate applications is restricted because of limitations in other battery components, in particular, the lack of an efficient binder. Herein, a novel multicomponent polymer gel binder (PGB) is presented, comprising the biopolymer chitosan as the host, embedded with the 1-butyl-1-methylpyrrolidinium dicyanamide (PYR14DCA) ionic liquid and the lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt. The multicomponent approach leads to carbon black arrangement along well-distributed chitosan chains in the electrodes, forming a highly electronic conductive network. Furthermore, the plasticizing effect of the ionic liquid leads to an enhanced ionic conductivity. As a result, shorter charge-transfer paths are enabled, leading to an exceptionally high rate capability in LiFePO4 and Li4Ti5O12 half cells, up to 50C. LiFePO4||Li4Ti5O12 full cells using the PGB for both electrodes also demonstrated stable cycling at 10C, with an impressively high discharge capacity of 173 mA h·g-1 after 1000 cycles. In addition, freestanding electrodes could also be realized and functioning flexible Li-ion cells were successfully demonstrated. Thus, the novel water-processable binder offers multifaceted advantages, making the approach highly promising for industrial implementation.

ROS-generation and cellular uptake behavior of amino-silica nanoparticles arisen from their uploading by both iron-oxides and hexamolybdenum clusters.

The present work introduces combination of superparamagnetic iron oxides (SPIONs) and hexamolybdenum cluster ([{Mo6I8}I6]2-) units within amino-decorated silica nanoparticles (SNs) as promising design of the hybrid SNs as efficient cellular contrast and therapeutic agents. The heating generated by SNs doped with SPIONs (Fe3O4@SNs) under alternating magnetic field is characterized by high specific absorption rate (SAR = 446 W/g). The cluster units deposition onto both Fe3O4@SNs and "empty" silica nanoparticles (SNs) results in Fe3O4@SNs[{Mo6I8}I6] and SNs[{Mo6I8}I6] with red cluster-centered luminescence and ability to generate reactive oxygen species (ROS) under the irradiation. The monitoring of spin-trapped ROS by ESR spectroscopy technique indicates that the ROS-generation decreases in time for SNs[{Mo6I8}I6] and [{Mo6I8}I6]2- in aqueous solutions, while it remains constant for Fe3O4@SNs[{Mo6I8}I6]. The cytotoxicity is low for both Fe3O4@SNs[{Mo6I8}I6] and SNs[{Mo6I8}I6], while the flow cytometry indicates preferable cellular uptake of the former versus the latter type of the nanoparticles. Moreover, entering into nucleus along with cytoplasm differentiates the intracellular distribution of Fe3O4@SNs[{Mo6I8}I6] from that of SNs[{Mo6I8}I6], which remain in the cell cytoplasm only. The exceptional behavior of Fe3O4@SNs[{Mo6I8}I6] is explained by residual amounts of iron ions at the silica surface.

Magnetic field assisted nanoparticle dispersion.

Magnetohydrodynamic nanoparticle dispersion is an energy efficient method to deaggregate nanoparticles, combining hydrodynamic forces of turbulent flow with Lorentz forces generated by a magnetic field.

Nitrogen-Doped Biomass-Derived Carbon Formed by Mechanochemical Synthesis for Lithium-Sulfur Batteries.

Nitrogen-doped carbons were synthesized by a solvent-free mechanochemically induced one-pot synthesis by using renewable biomass waste. Three solid materials are used: sawdust as a carbon source, urea and/or melamine as a nitrogen source, and potassium carbonate as an activation agent. The resulting nitrogen-doped porous carbons offer a very high specific surface area of up to 3000 m2 g-1 and a large pore volume up to 2 cm3 g-1 . Also, a high nitrogen content of 4 wt % (urea only) up to 12 wt % (melamine only) is generated, depending on the nitrogen and carbon sources. The mechanochemical reaction and the impact of different wood components on the porosity and surface functionalities are investigated by nitrogen physisorption and high-resolution X-ray photoelectron spectroscopy (XPS). These N-doped carbons are highly suitable as cathode materials for Li-S batteries, showing high initial discharge capacities of up to 1300 mAh gsulfur -1 (95 % coulombic efficiency) and >75 % capacity retention within the first 50 cycles at low electrolyte volume.

Fluorescent magnetic nanoparticles for modulating the level of intracellular Ca2+ in motoneurons.

This report introduces both synthesis and in vitro biological behaviour of dual magnetic-fluorescent silica nanoparticles. The amino group-decoration of 78 nm sized silica nanoparticles enables their efficient internalization into motoneurons, which is visualized by the red fluorescence arising from [Ru(dipy)3]2+ complexes encapsulated into a silica matrix. The internalized nanoparticles are predominantly located in the cell cytoplasm as revealed by confocal microscopy imaging. The magnetic function of the nanoparticles resulted from the incorporation of 17 nm sized superparamagnetic iron oxide cores into the silica matrix, enabling their responsivity to magnetic fields. Fluorescence analysis revealed the "on-off" switching of Ca2+ influx under the application and further removal of the permanent magnetic field. This result for the first time highlights the movement of the nanoparticles within the cell cytoplasm in the permanent magnetic field as a promising tool to enhance the neuronal activity of motoneurons.

Selective adsorption and separation of ortho-substituted alkylaromatics with the microporous aluminum terephthalate MIL-53.

The metal-organic framework MIL-53(Al) was tested for selective adsorption and separation of xylenes and ethylbenzene, ethyltoluenes, and cymenes using batch, pulse chromatographic, and breakthrough experiments. In all conditions tested, MIL-53 has the largest affinity for the ortho-isomer among each group of alkylaromatic compounds. Separations of the ortho-compounds from the other isomers can be realized using a column packed with MIL-53 crystallites. As evidenced by Rietveld refinements, specific interactions of the xylenes with the pore walls of MIL-53 determine selectivity. In comparison with the structurally similar metal-organic framework MIL-47, the selectivities among alkylaromatics found for MIL-53 are different. Separation of ethyltoluene and cymene isomers is more effective on MIL-53 than on MIL-47; the pores of MIL-53 seem to be a more suitable environment for hosting the larger ethyltoluene and cymene isomers than those of MIL-47.