RESUMO
Migration kinetic data from general purpose polystyrene (GPPS) and high impact polystyrene (HIPS) were generated for a set of model substances as well as styrene monomer and oligomers at different temperatures (20 °C, 40 °C, 60 °C) using food simulants stipulated in the European Regulation (EU) 10/2011 and real foods like milk, cream and olive oil (20 °C, 40 °C). The extent of polymer swelling was characterized gravimetrically and visual changes of the test specimens after migration contact were recorded. Isooctane and 95% ethanol caused strong swelling and visual changes of HIPS, overestimating real migration into foods especially at high temperatures; GPPS was affected by isooctane only at 60 °C. With 50% ethanol, after 10 days contact at 60 °C or 40 °C both polymers were slightly swollen. Contrary, most of the real foods analyzed caused no detectable swelling or visual changes of the investigated polymers. This study demonstrates that the recommendations provided by EU regulations are not always in agreement with the physicochemical properties of styrenic polymers. The critical point remains the selection of adequate food simulants/testing conditions, since the high overestimation of aggressive media can lead to non-compliance of polystyrene materials even if the migration into real food would be of no concern.
RESUMO
In view of the fact that a specific migration limit (SML) is to be established in the near future for styrene monomer in plastic food contact materials (FCMs), data on the dietary exposure of the European population, as well as sensitive and reliable analytical methodologies to implement compliance testing, are needed. The properties of the substance styrene as well as those of styrenic polymers pose challenges for analysts and their design of experimental migration tests. The aim of this study was to assess the level of styrene in polystyrene (PS)-packed dairy products from supermarkets and compare these values with the results from simulated migration testing. In addition to the conventional food simulant and test conditions described in Regulation (EU) No 10/2011 for refrigerated dairy products (50% ethanol for 10 days at 40 °C), milder simulants and test conditions (10% ethanol and 20% ethanol for 10 days at 40 °C and 20 °C) were investigated. Styrene levels in the investigated foods ranged from 2.8 µg/kg to 22.4 µg/kg. The use of 50% ethanol causes interactions with PS (swelling) that do not occur with dairy products and leads to highly exaggerated migration results. In contrast, testing PS for 10 days at 40 °C with 10% and 20% ethanol leads to higher styrene migration levels than found in real food, which are still conservative but far less extreme. Testing PS for 10 days at 20 °C leads to styrene migration levels that are more comparable to, but still overestimate, those found in real food products stored under refrigerated conditions.
RESUMO
The European Food Safety Authority is re-evaluating styrene for assessing the safety of food contact materials (FCM) such as polystyrene (PS) and started a systematic review of the data on migration levels in food. A restriction for styrene is expected in the near future. The main food contact application of PS is dairy packaging, mainly at refrigerated storage. In this study, seventeen dairy products packed in PS taken from the Italian and German markets were investigated. Styrene concentrations in the refrigerated dairy products (yogurt, cream) ranged from 5 to 30 µg/kg at the best before date, while in single serving portions of coffee creamer, which were stored at room temperature until the best before date of approx. 190 days, 401 µg/kg were measured. Among several parameters, the ratio between the surface contact area of the package and the quantity of the food packed, the time/temperature conditions of production/filling and storage of the products were identified as the main factors influencing styrene migration into food under realistic conditions. Yogurts fermented in the pots for approximately 8 h at 40-50 °C showed higher styrene levels than those fermented in an incubator and filled at 20 °C. The fat content might influence the styrene level but the effect, if any, was too small in relation to the variability of other parameters. Levels of styrene migrating into 50% ethanol food simulant under standardized condition (10 days/40 °C) were found to be much higher than levels in refrigerated foods. This raises the question as to whether compliance testing for PS plastics should be adapted taking into consideration the correlation between migration testing by laboratory simulations and migration into real food.
RESUMO
Polyethylene terephthalate (PET) bottles are widely used as packaging material for natural mineral water. However, trace levels of acetaldehyde can migrate into natural mineral water during the shelf life and might influence the taste of the PET bottled water. 2-Aminobenzamide is widely used during PET bottle production as a scavenging agent for acetaldehyde. The aim of this study was the determination of the migration kinetics of 2-aminobenzamide into natural mineral water as well as into 20% ethanol. From the migration kinetics, the diffusion coefficients of 2-aminobenzamide in PET at 23 and 40°C were determined to be 4.2 × 10(-)(16) and 4.2 × 10(-)(15) cm(2) s(-1), respectively. The diffusion coefficient for 20% ethanol at 40°C was determined to be 7.7 × 10(-)(15) cm(2) s(-1), which indicates that 20% ethanol is causing swelling of the PET polymer. From a comparison of migration values between 23 and 40°C, acceleration factors of 9.7 when using water as contact medium and 18.1 for 20% ethanol as simulant can be derived for definition of appropriate accelerated test conditions at 40°C. The European Union regulatory acceleration test based on 80 kJ mol(-1) as conservative activation energy overestimates the experimentally determined acceleration rates by a factor of 1.6 and 3.1, respectively.