Electrochemical Assessment of Indigo Carmine Dye in Lithium Metal Polymer Technology.

Lithium metal batteries are inspiring renewed interest in the battery community because the most advanced designs of Li-ion batteries could be on the verge of reaching their theoretical specific energy density values. Among the investigated alternative technologies for electrochemical storage, the all-solid-state Li battery concept based on the implementation of dry solid polymer electrolytes appears as a mature technology not only to power full electric vehicles but also to provide solutions for stationary storage applications. With an effective marketing started in 2011, BlueSolutions keeps developing further the so-called lithium metal polymer batteries based on this technology. The present study reports the electrochemical performance of such Li metal batteries involving indigo carmine, a cheap and renewable electroactive non-soluble organic salt, at the positive electrode. Our results demonstrate that this active material was able to reversibly insert two Li at an average potential of ≈2.4 V vs. Li+/Li with however, a relatively poor stability upon cycling. Post-mortem analyses revealed the poisoning of the Li electrode by Na upon ion exchange reaction between the Na countercations of indigo carmine and the conducting salt. The use of thinner positive electrodes led to much better capacity retention while enabling the identification of two successive one-electron plateaus.

From Solid-Solution Electrodes and the Rocking-Chair Concept to Today's Batteries.

Lithium-ion batteries (LIBs) have become ubiquitous power sources for small electronic devices, electric vehicles, and stationary energy storage systems. Despite the success of LIBs which is acknowledged by their increasing commodity market, the historical evolution of the chemistry behind the LIB technologies is laden with obstacles and yet to be unambiguously documented. This Viewpoint outlines chronologically the most essential findings related to today's LIBs, including commercial electrode and electrolyte materials, but furthermore also depicts how the today popular and widely emerging solid-state batteries were instrumental at very early stages in the development of LIBs.

Nanoscale Chemical Evolution of Silicon Negative Electrodes Characterized by Low-Loss STEM-EELS.

Continuous solid electrolyte interface (SEI) formation remains the limiting factor of the lifetime of silicon nanoparticles (SiNPs) based negative electrodes. Methods that could provide clear diagnosis of the electrode degradation are of utmost necessity to streamline further developments. We demonstrate that electron energy-loss spectroscopy (EELS) in a scanning transmission electron microscope (STEM can be used to quickly map SEI components and quantify LixSi alloys from single experiments with resolutions down to 5 nm. Exploiting the low-loss part of the EEL spectrum allowed us to circumvent the degradation phenomena that have so far crippled the application of this technique on such beam-sensitive compounds. Our results provide unprecedented insight into silicon aging mechanisms in full cell configuration. We observe the morphology of the SEI to be extremely heterogeneous at the particle scale but with clear chemical evolutions with extended cycling coming from both SEI accumulation and a transition from lithium-rich carbonate-like compounds to lithium-poor ones. Thanks to the retrieval of several results from a single data set we were able to correlate local discrepancies in lithiation to the initial crystallinity of silicon as well as to the local SEI chemistry and morphology. This study emphasizes how initial heterogeneities in the percolating electronic network and the porosity affect SiNPs aggregates along cycling. These findings pinpoint the crucial role of an optimized formulation in silicon-based thick electrodes.

Lithium n-Doped Polyaniline as a High-Performance Electroactive Material for Rechargeable Batteries.

The discovery of conducting lithium-doped polyaniline with reversible redox chemistry allows simultaneous unprecedented capacity and stability in a non-aqueous Li battery. This compound (lithium emeraldinate) was synthesized by lithium-proton exchange on the emeraldine base in an anhydrous lithium-based electrolyte. A combination of UV/Vis-NIR spectroelectrochemistry, XPS, FTIR, and EQCM characterization allowed a unified description of the chemical and electrochemical behavior, showing facile charge delocalization of the doped states and the reversibility of the redox processes in this form of polyaniline. From a practical point of view, lithium emeraldinate behaves as a high-capacity organic active material (230 mAh g-1 ) that enables preparation of relatively thick composite electrodes with a low amount of carbon additives and high energy density (460 Wh kg-1 ). Concomitantly, at 1C rate, 400 cycles were achieved without significant capacity loss, while the coulombic efficiency is greater than 99 %.

Suspensions of carbon nanofibers in organic medium: rheo-electrical properties.

The nonaqueous suspensions of carbon nanofibers (CNFs) in 1 M lithium bis(trifluoromethanesulfonaimide) in propylene carbonate electrolyte reveal unique structural evolution and shear-induced transition due to the high aspect ratio. The rheo-electrical behavior elucidates a microstructural transition from entangled-to-aggregated networks above a distinct percolation threshold. Under shear flow, both networks show a three-regime flow curve and an inverted-bell-like conductivity curve as a consequence of shear-induced alignment (entangled network) and shear-induced breaking up (aggregated network). The different particle morphology of carbon nanofibers (anisometric) and carbon black (CB; isometric) causes different aggregation mechanisms (aggregate vs. particulate) and then varied microstructure for their suspensions in the same electrolyte. This fact explains the higher rigidity and lower electric conductivity of CNFs than CB suspensions. Interestingly, the suspension of hybrid carbons at the optimum mixing ratio merges the advantages of both carbons to operate efficiently as precursors in the formulation of electrodes for energy storage systems.

Elucidation of the Na(2/3)FePO4 and Li(2/3)FePO4 intermediate superstructure revealing a pseudouniform ordering in 2D.

Based on TEM, synchrotron X-ray diffraction, DFT calculations, and Mössbauer spectroscopy, a unified understanding of the Na and Li intercalation process in FePO4 is proposed. The key to this lies in solving the highly sought-after intermediate A(2/3)FePO4 (A = Na, Li) superstructures that are characterized by alkali ions as well as Fe(II)/Fe(III) charge orderings in a monoclinic three-fold supercell. Formation energies and electrochemical potential calculations confirm that Na(2/3)FePO4 and Li(2/3)FePO4 are stable and metastable, respectively, and that they yield insertion potentials in fair agreement with experimental values. The 2/3 Na(Li) and 1/3 vacancy sublattice of the intermediate phases forms a dense (101)(Pnma) plane in which the atom/vacancy ordering is very similar to that predicted for the most uniform distribution of 1/3 of vacancies in a 2D square lattice. Structural analysis strongly suggests that the key role of this dense plane is to constrain the intercalation in the diffusion channels to operate by cooperative filling of (bc)(Pnma). From a practical point of view, this generalized mechanism highlights the fact that an interesting strategy for obtaining high-rate FePO4 materials would consist in designing grains with an enhanced (101) surface area, thereby offering potential for substantial improvements with respect to the performance of rechargeable Li and Na batteries.

Interphase evolution at two promising electrode materials for Li-ion batteries: LiFePO4 and LiNi1/2 Mn1/2O2.

The present review reports the characterization and control of interfacial processes occurring on olivine LiFePO(4) and layered LiNi(1/2) Mn(1/2)O(2), standing here as model compounds, during storage and electrochemical cycling. The formation and evolution of the interphase created by decomposition of the electrolyte is investigated by using spectroscopic tools such as magic-angle-spinning nuclear magnetic resonance ((7)Li,(19)F and (31)P) and electron energy loss spectroscopy, in parallel to X-ray photoelectron spectroscopy, to quantitatively describe the interphase and unravel its architecture. The influence of the pristine surface chemistry of the active material is carefully examined. The importance of the chemical history of the surface of the electrode material before any electrochemical cycling and the strong correlation between interface phenomena, the formation/evolution of an interphase, and the electrochemical behavior appear clearly from the use of these combined characterization probes. This approach allows identifying interface aging and failure mechanisms. Different types of surface modifications are then investigated, such as intrinsic modifications upon aging in air or methods based on the use of additives in the electrolyte or carbon coatings on the surface of the active materials. In each case, the species detected on the surface of the materials during storage and cycling are correlated with the electrochemical performance of the modified positive electrodes.

Numerical and experimental study of suspensions containing carbon blacks used as conductive additives in composite electrodes for lithium batteries.

Suspensions of carbon blacks and spherical carbon particles are studied experimentally and numerically to understand the role of the particle shape on the tendency to percolation. Two commercial carbon blacks and one lab-synthesized spherical carbon are used. The percolation thresholds in suspensions are experimentally determined by two complementary methods: impedance spectroscopy and rheology. Brownian dynamics simulations are performed to explain the experimental results taking into account the fractal shape of the aggregates in the carbon blacks. The results of Brownian dynamics simulations are in good agreement with the experimental results and allow one to explain the experimental behavior of suspensions.

Synergistic effect in carbon coated LiFePO4 for high yield spontaneous grafting of diazonium salt. Structural examination at the grain agglomerate scale.

Molecular grafting of p-nitrobenzene diazonium salt at the surface of (Li)FePO4-based materials was thoroughly investigated. The grafting yields obtained by FTIR, XPS, and elemental analysis for core shell LiFePO4-C are found to be much higher than the sum of those associated with either the LiFePO4 core or the carbon shell alone, thereby revealing a synergistic effect. Electrochemical, XRD, and EELS experiments demonstrate that this effect stems from the strong participation of the LiFePO4 core that delivers large amounts of electrons to the carbon substrate at a constant energy, above the Fermi level of the diazonium salt. Correspondingly large multilayer anisotropic structures that are associated with outstanding grafting yields could be observed from TEM experiments. Results therefore constitute strong evidence of a grafting mechanism where homolytic cleavage of the N2(+) species occurs together with the formation and grafting of radical nitro-aryl intermediates. Although the oxidation and concomitant Li deintercalation of LiFePO4 grains constitute the main driving force of the functionalization reaction, EFTEM EELS mapping shows a striking lack of spatial correlation between grafted grains and oxidized ones.

Non-aqueous carbon black suspensions for lithium-based redox flow batteries: rheology and simultaneous rheo-electrical behavior.

We report on the rheological and electrical properties of non-aqueous carbon black (CB) suspensions at equilibrium and under steady shear flow. The smaller the primary particle size of carbon black is, the higher the magnitude of rheological parameters and the conductivity are. The electrical percolation threshold ranges seem to coincide with the strong gel rather than the weak gel rheological threshold ones. The simultaneous measurements of electrical properties under shear flow reveal the well-known breaking-and-reforming mechanism that characterises such complex fluids. The small shear rate breaks up the network into smaller agglomerates, which in turn transform into anisometric eroded ones at very high shear rates, recovering the network conductivity. The type of carbon black, its concentration range and the flow rate range are now precisely identified for optimizing the performance of a redox flow battery. A preliminary electrochemical study for a composite anolyte (CB/Li4Ti5O12) at different charge-discharge rates and thicknesses is shown.

Residual Li2O degrades PVdF during the preparation of NMC811 slurries for Li-ion batteries.

7Li MAS NMR quantification of lithiated species at the surface of aged NMC811 industrial powders and slurries shows that the electrode preparation process exacerbates Li extraction. A combination of 7Li MAS NMR and XPS suggest a new reaction for the PVdF binder degradation, involving in fact Li2O as the reagent and the formation of LiF.

Brownian dynamics simulations of colloidal suspensions containing polymers as precursors of composite electrodes for lithium batteries.

Dilute aqueous suspensions of silicon nanoparticles and sodium carboxymethylcellulose salt (CMC) are studied experimentally and numerically by brownian dynamics simulations. The study focuses on the adsorption of CMC on silicon and on the aggregation state as a function of the suspension composition. To perform simulations, a coarse-grained model has first been developed for the CMC molecules. Then, this model has been applied to study numerically the behavior of suspensions of silicon and CMC. Simulation parameters have been fixed on the basis of experimental characterizations. Results of brownian dynamics simulations performed with our model are found in qualitative good agreement with experiments and allow a good description of the main features of the experimental behavior.

Pristine Surface of Ni-Rich Layered Transition Metal Oxides as a Premise of Surface Reactivity.

The surface reactivity of Ni-rich layered transition metal oxides is instrumental to the performance of batteries based on these positive electrode materials. Most often, strong surface modifications are detailed with respect to a supposed ideal initial state. Here, we study the LiNi0.8Mn0.1Co0.1O2 (NMC811) cathode material in its pristine state, hence before any contact with electrolyte or cycling, thanks to advanced microscopy and spectroscopy techniques to fully characterize its surface down to the nanometer scale. Scanning transmission electron microscopy-electron energy loss spectroscopy (STEM-EELS), solid-state nuclear magnetic resonance (SS-NMR), and X-ray photoelectron spectroscopy (XPS) are combined and correlated in an innovative manner. The results demonstrate that in usual storage conditions after synthesis, the extreme surface is already chemically different from the nominal values. In particular, nickel is found in a reduced state compared to the bulk value, and a Mn enrichment is determined in the first few nanometers of primary particles. Further exposition to humid air allows for quantifying the formed lithiated species per gram of active material, identifying their repartition and proposing a reaction path in relation with the instability of the surface.

Understanding the Capacity Decay of Si/NMC622 Li-Ion Batteries Cycled in Superconcentrated Ionic Liquid Electrolytes: A New Perspective.

Silicon-containing Li-ion batteries have been the focus of many energy storage research efforts because of the promise of high energy density. Depending on the system, silicon generally demonstrates stable performance in half-cells, which is often attributed to the unlimited lithium supply from the lithium (Li) metal counter electrode. Here, the electrochemical performance of silicon with a high voltage NMC622 cathode was investigated in superconcentrated phosphonium-based ionic liquid (IL) electrolytes. As a matter of fact, there is very limited work and understanding of the full cell cycling of silicon in such a new class of electrolytes. The electrochemical behavior of silicon in the various IL electrolytes shows a gradual and steeper capacity decay, compared to what we previously reported in half-cells. This behavior is linked to a different evolution of the silicon morphology upon cycling, and the characterization of cycled electrodes points toward mechanical reasons, complete disconnection of part of the electrode, or internal mechanical stress, due to silicon and Li metal volume variation upon cycling, to explain the progressive capacity fading in full cell configuration. An extremely stable solid electrolyte interphase (SEI) in the full Li-ion cells can be seen from a combination of qualitative and quantitative information from transmission electron microscopy, X-ray photoelectron spectroscopy, electrochemical impedance spectroscopy, and magic angle spinning nuclear magnetic resonance. Our findings provide a new perspective to full cell interpretation regarding capacity fading, which is oftentimes linked almost exclusively to the loss of Li inventory but also more broadly, and provide new insights into the impact of the evolution of silicon morphology on the electrochemical behavior.

Influence of the Polyacrylic Acid Binder Neutralization Degree on the Initial Electrochemical Behavior of a Silicon/Graphite Electrode.

The role of the physicochemical properties of the water-soluble polyacrylic acid (PAA) binder in the electrochemical performance of highly loaded silicon/graphite 50/50 wt % negative electrodes has been examined as a function of the neutralization degree x in PAAH1-xLix at the initial cycle in an electrolyte not containing ethylene carbonate. Electrode processing in the acidic PAAH binder at pH 2.5 leads to a deep copper corrosion, resulting in a significant electrode cohesion and adhesion to the current collector surface, but the strong binder rigidity may explain the big cracks occurring on the electrode surface at the first cycle. The nonuniform binder coating on the material surface leads to an important degradation of the electrolyte, explaining the lowest initial Coulombic efficiency and the lowest reversible capacity among the studied electrodes. When processed in neutral pH, the PAAH0.22Li0.78 binder forms a conformal artificial solid electrolyte interphase layer on the material surface, which minimizes the electrolyte reduction at the first cycle and then maximizes the initial Coulombic efficiency. However, the low mechanical resistance of the electrode and its strong cracking explain its low reversible capacity. Electrodes prepared at intermediate pH 4 combine the positive assets of electrodes prepared at acidic and neutral pH. They lead to the best initial performance with a notable areal capacity of 7.2 mA h cm-2 and the highest initial Coulombic efficiency of around 90%, a value much larger than the usual range reported for silicon/graphite anodes. All data obtained with complementary characterization techniques were discussed as a function of the PAA polymeric chain molecular conformation, microstructure, and surface adsorption or grafting, emphasizing the tremendous role of the binder in the electrode initial performance.

Tuning the Formation and Structure of the Silicon Electrode/Ionic Liquid Electrolyte Interphase in Superconcentrated Ionic Liquids.

The latest advances in the stabilization of Li/Na metal battery and Li-ion battery cycling have highlighted the importance of electrode/electrolyte interface [solid electrolyte interphase (SEI)] and its direct link to cycling behavior. To understand the structure and properties of the SEI, we used combined experimental and computational studies to unveil how the ionic liquid (IL) cation nature and salt concentration impact the silicon/IL electrolyte interfacial structure and the formed SEI. The nature of the IL cation is found to be important to control the electrolyte reductive decomposition that influences the SEI composition and properties and the reversibility of the Li-Si alloying process. Also, increasing the Li salt concentration changes the interface structure for a favorable and less resistive SEI. The most promising interface for the Si-based battery was found to be in P1222FSI with 3.2 m LiFSI, which leads to an optimal SEI after 100 cycles in which LiF and trapped LiFSI are the only distinguishable lithiated and fluorinated products detected. This study shows a clear link between the nanostructure of the IL electrolyte near the electrode surface, the resulting SEI, and the Si negative electrode cycling performance. More importantly, this work will aid the rational design of Si-based Li-ion batteries using IL electrolytes in an area that has so far been neglected, reinforcing the benefits of superconcentrated electrolyte systems.

Valence electron energy-loss spectroscopy of silicon negative electrodes for lithium batteries.

All compounds present in the lithium-silicon binary phase diagram were synthesized and analyzed by electron energy-loss spectroscopy. In order to limit beam damage, and to develop a fast and local method of characterizing silicon negative electrodes, the valence energy-loss spectrum region was investigated, in particular the very intense plasmon peak in these alloys. Experimental spectra are in strong agreement with theoretical ones obtained from density functional theory. These results constitute a database for Li(x)Si alloys' plasmon energies. The method is applied to the study of the first discharge of a silicon electrode, thus identifying a Li(2.9+/-0.3)Si phase in equilibrium with Si on the voltage plateau. A nucleation process of this phase in the pristine Si is revealed, as well as a possible over-lithiation beyond the end of discharge Li(15)Si(4) crystalline phase.

Structural changes in surface and bulk LiNi0.5Mn0.5O2 during electrochemical reaction on epitaxial thin-film electrodes characterized by in situ X-ray scattering.

Surface and bulk structural changes of LiNi(0.5)Mn(0.5)O(2) were investigated during electrochemical reaction using synchrotron X-ray scattering and a restricted reaction plane consisting of two-dimensional epitaxial-film electrodes. The changes in bulk structure confirmed lithium diffusion through the (110) surface, which was perpendicular to the two-dimensional (2D) edges of the layered structure. No (de)intercalation reaction was observed through the (003) surface at voltages of 3.0-5.0 V. However, intercalation did proceed through the (003) plane below 3.0 V, indicating unusual three-dimensional (3D) lithium diffusion in the over-lithiated 2D structure. During the electrochemical process, the surface of the electrode showed different structure changes from those of the bulk structure. The reaction mechanism of the intercalation electrodes for lithium batteries is discussed on the basis of surface and bulk structural changes.

Thermomechanical Polymer Binder Reactivity with Positive Active Materials for Li Metal Polymer and Li-Ion Batteries: An XPS and XPS Imaging Study.

The lithium and lithium-ion battery electrode chemical stability in the pristine state has rarely been considered as a function of the binder choice and the electrode processing. In this work, X-ray photoelectron spectroscopy (XPS) and XPS imaging analyses associated with complementary Mössbauer spectroscopy are used in order to study the chemical stability of two pristine positive electrodes: (i) an extruded LiFePO4-based electrode formulated with different polymer matrices [polyethylene oxide and a polyvinylidene difluoride (PVdF)] and processed at different temperatures (90 and 130 °C, respectively) and (ii) a Li[Ni0.5Mn0.3Co0.2]O2 (NMC)-based electrode processed by tape-casting, followed by a mild or heavy calendering treatment. These analyses have allowed the identification of reactivity mechanisms at the interface of the active material and the polymer in the case of PVdF-based electrodes.

Raising the redox potential in carboxyphenolate-based positive organic materials via cation substitution.

Meeting the ever-growing demand for electrical storage devices requires both superior and "greener" battery technologies. Nearly 40 years after the discovery of conductive polymers, long cycling stability in lithium organic batteries has now been achieved. However, the synthesis of high-voltage lithiated organic cathode materials is rather challenging, so very few examples of all-organic lithium-ion cells currently exist. Herein, we present an inventive chemical approach leading to a significant increase of the redox potential of lithiated organic electrode materials. This is achieved by tuning the electronic effects in the redox-active organic skeleton thanks to the permanent presence of a spectator cation in the host structure exhibiting a high ionic potential (or electronegativity). Thus, substituting magnesium (2,5-dilithium-oxy)-terephthalate for lithium (2,5-dilithium-oxy)-terephthalate enables a voltage gain of nearly +800 mV. This compound being also able to act as negative electrode via the carboxylate functional groups, an all-organic symmetric lithium-ion cell exhibiting an output voltage of 2.5 V is demonstrated.