Diffusion-driven fed-batch fermentation in perforated ring flasks.

PURPOSE: Simultaneous membrane-based feeding and monitoring of the oxygen transfer rate shall be introduced to the newly established perforated ring flask, which consists of a cylindrical glass flask with an additional perforated inner glass ring, for rapid bioprocess development. METHODS: A 3D-printed adapter was constructed to enable monitoring of the oxygen transfer rate in the perforated ring flasks. Escherichia coli experiments in batch were performed to validate the adapter. Fed-batch experiments with different diffusion rates and feed solutions were performed. RESULTS: The adapter and the performed experiments allowed a direct comparison of the perforated ring flasks with Erlenmeyer flasks. In batch cultivations, maximum oxygen transfer capacities of 80 mmol L-1 h-1 were reached with perforated ring flasks, corresponding to a 3.5 times higher capacity than in Erlenmeyer flasks. Fed-batch experiments with a feed reservoir concentration of 500 g glucose L-1 were successfully conducted. Based on the oxygen transfer rate, an ammonium limitation could be observed. By adding 40 g ammonium sulfate L-1 to the feed reservoir, the limitation could be prevented. CONCLUSION: The membrane-based feeding, an online monitoring technique, and the perforated ring flask were successfully combined and offer a new and promising tool for screening and process development in biotechnology.

In situ formation of a MoS2 -based inorganic-organic nanocomposite by directed thermal decomposition.

Nanocomposites based on molybdenum disulfide (MoS2 ) and different carbon modifications are intensively investigated in several areas of applications due to their intriguing optical and electrical properties. Addition of a third element may enhance the functionality and application areas of such nanocomposites. Herein, we present a facile synthetic approach based on directed thermal decomposition of (Ph4 P)2 MoS4 generating MoS2 nanocomposites containing carbon and phosphorous. Decomposition at 250 °C yields a composite material with significantly enlarged MoS2 interlayer distances caused by in situ formation of Ph3 PS bonded to the MoS2 slabs through MoS bonds and (Ph4 P)2 S molecules in the van der Waals gap, as was evidenced by (31) P solid-state NMR spectroscopy. Visible-light-driven hydrogen generation demonstrates a high catalytic performance of the materials.

Validation of computational fluid dynamics of shake flask experiments at moderate viscosity by liquid distributions and volumetric power inputs.

Computational fluid dynamics (CFD) has recently become a pivotal tool in the design and scale-up of bioprocesses. While CFD has been extensively utilized for stirred tank reactors (STRs), there exists a relatively limited body of literature focusing on CFD applications for shake flasks, almost exclusively concentrated on fluids at waterlike viscosity. The importance of CFD model validation cannot be overstated. While techniques to elucidate the internal flow field are necessary for model validation in STRs, the liquid distribution, caused by the orbital shaking motion of shake flasks, can be exploited for model validation. An OpenFOAM CFD model for shake flasks has been established. Calculated liquid distributions were compared to suitable, previously published experimental data. Across a broad range of shaking conditions, at waterlike and moderate viscosity (16.7 mPa∙s), the CFD model's liquid distributions align excellently with the experimental data, in terms of overall shape and position of the liquid relative to the direction of the centrifugal force. Additionally, the CFD model was used to calculate the volumetric power input, based on the energy dissipation. Depending on the shaking conditions, the computed volumetric power inputs range from 0.1 to 7 kW/m3 and differed on average by 0.01 kW/m3 from measured literature data.

Synthesis, characterization and reactivity of group 4 metallocene bis(diphenylphosphino)acetylene complexes-a reactivity and bonding study.

A study of the coordination chemistry of bis(diphenylphosphino)acetylene, Ph2P-C≡C-PPh2, with selected group 4 metallocenes is presented. By substitution of the alkyne in complexes of the type Cp'2M(L)(η(2)-Me3SiC2SiMe3) (M = Ti, no L; M = Zr, L = pyridine; Cp' = substituted or unsubstituted bridged or unbridged η(5)-cyclopentadienyl), the expected mononuclear complexes Cp*2Ti(η(2)-Ph2PC2PPh2) (4Ti), (rac-ebthi)Ti(η(2)-Ph2PC2PPh2) (5Ti), and (rac-ebthi)Zr(η(2)-Ph2PC2PPh2) (5Zr) [ebthi = ethylenebis(tetrahydroindenyl)] were obtained. When [Cp2Zr] was used in the reaction of Cp2Zr(py)(η(2)-Me3SiC2SiMe3) with Ph2P-C≡C-PPh2, the dinuclear complex [Cp2Zr(η(2)-Ph2PC2PPh2)]2 (6) was formed and isolated in the solid state. In solution, this complex is in equilibrium with the very spectacular structure of complex 7b as the first example of such a highly strained four-membered heterometallacycle of a group 4 metal, involving the rare R2PCCR' fragment in the cyclic unit. Both the stability and reactivity of heterodisubstituted alkynes X-C≡C-X (X = NR2, PR2, SR, SiR3, etc.) themselves and also of their complexes are of general interest. Complex 6 did not react with a second [Cp2Zr] fragment to form a homobimetallic complex. In contrast, for (rac-ebthi)Zr(η(2)-Ph2PC2PPh2) (5Zr) this reaction occurs. In the reaction of complex 4Ti with the Ni(0) complex (Cy3P)2Ni(η(2)-C2H4) (Cy = cyclohexyl), C-P bond cleavage of the alkyne ligand resulted in the formation of the isolated complex [(Cy3P)Ni(µ-PPh2)]2 (11). The structure and bonding of the complexes were investigated by DFT analysis to compare the different possible coordination modes of the R2P-C≡C-PR2 ligand. For compound 7b, a flip-flop coordination of the phosphorus atoms was proposed. Complexes 4Ti, 5Ti, 5Zr, 6, and 11 were characterized by X-ray crystallography.

Synthesis and structures of ansa-titanocene complexes with diatomic bridging units for overall water splitting.

The synthesis of a series of ansa-titanocene dichlorides [Cp'2TiCl2] (Cp' = bridged η(5)-tetramethylcyclopentadienyl) and the corresponding titanocene bis(trimethylsilyl)acetylene complexes [Cp'2Ti(η(2)-Me3SiC2SiMe3)] is described. The ethanediyl-bridged complexes [C2H4(C5Me4)2TiCl2] (2-Cl2) and [C2H4(C5Me4)2Ti(η(2)-Me3SiC2SiMe3)] (2-btmsa; btmsa = η(2)-Me3SiC2SiMe3) can be obtained from the hitherto unknown calcocenophane complex [C2H4(C5Me4)2Ca(THF)2] (1). Furthermore, a heterodiatomic bridging unit containing both, a dimethylsilyl and a methylene group was introduced to yield the ansa-titanocene dichloride [Me2SiCH2(C5Me4)2TiCl2] (3-Cl2) and the bis(trimethylsilyl)acetylene complex [Me2SiCH2(C5Me4)2Ti(η(2)-Me3SiC2SiMe3)] (3-btmsa). Besides, tetramethyldisilyl- and dimethylsilyl-bridged metallocene complexes (structural motif 4 and 5, respectively) were prepared. All ansa-titanocene alkyne complexes were reacted with stoichiometric amounts of water; the hydrolysis products were isolated as model complexes for the investigation of the elemental steps of overall water splitting. Compounds 1, 2-btmsa, 2-(OH)2, 3-Cl2, 3-btmsa, 4-(OH)2, 3-alkenyl and 5-alkenyl were characterised by X-ray diffraction analysis.

Highly strained heterometallacycles of Group†4 metallocenes with bis(diphenylphosphino)methanide ligands.

A study of the coordination chemistry of different bis(diphenylphosphino)methanide ligands [Ph2PC(X)PPh2] (X = H, SiMe3) with Group 4 metallocenes is presented. The paramagnetic complexes [Cp2Ti{κ(2)-P,P-Ph2PC(X)PPh2}] (X = H (3 a), X = SiMe3 (3 b)) have been prepared by the reactions of [(Cp2TiCl)2] with [Li{C(X)PPh2}2(thf)3]. Complex 3 b could also be synthesized by reaction of the known titanocene alkyne complex [Cp2Ti(η(2)-Me3SiC2SiMe3)] with Ph2PC(H)(SiMe3)PPh2 (2 b). The heterometallacyclic complex [Cp2Zr(H){κ(2)-P,P-Ph2PC(H)PPh2}] (4 aH) has been prepared by reaction of the Schwartz reagent with [Li{C(H)PPh2}2(thf)3]. Reactions of [Cp2HfCl2] with [Li{C(X)PPh2}2(thf)3] gave the highly strained corresponding metallacycles [Cp2M(Cl){κ(2)-P,P-Ph2PC(X)PPh2}] (5 aCl and 5 bCl) in very good yields. Complexes 3 a, 4 aH, and 5 aCl have been characterized by X-ray crystallography. Complex 3 a has also been characterized by EPR spectroscopy. The structure and bonding of the complexes has been investigated by DFT analysis. Reactions of complexes 4 aH, 5 aCl, and 5 bCl did not give the corresponding more unsaturated heterometallacyclobuta-2,3-dienes.

{N,N-Bis[bis-(2,2,2-tri-fluoro-eth-oxy)phosphan-yl]methyl-amine-κ(2) P,P'}bis-(η(5)-cyclo-penta-dien-yl)titanium(II).

The title compound, [Ti(C5H5)2(C9H11F12NO4P2)], is a four-membered titanacycle obtained from the reaction of Cp2Ti(η(2)-Me3SiC2SiMe3) and CH3N[P(OCH2CF3)2]2 {N,N-bis-[bis-(tri-fluoro-eth-oxy)phosphan-yl]methyl-amine, tfepma}. The Ti(II) atom is coordinated by two cyclo-penta-dienyl (Cp) ligands and the chelating tfepma ligand in a strongly distorted tetra-hedral geometry. The mol-ecule is located on a mirror plane.

Highly strained heterometallacycles of Group†4 metallocenes with bis(diphenylphosphino)amide ligands.

A study regarding coordination chemistry of the bis(diphenylphosphino)amide ligand Ph(2) P-N-PPh(2) at Group 4 metallocenes is presented herein. Coordination of N,N-bis(diphenylphosphino)amine (1) to [(Cp(2) TiCl)(2) ] (Cp=η(5) -cyclopentadienyl) generated [Cp(2) Ti(Cl)P(Ph(2) )N(H)PPh(2) ] (2). The heterometallacyclic complex [Cp(2) Ti(κ(2) -P,P-Ph(2) P-N-PPh(2) )] (3 Ti) can be prepared by reaction of 2 with n-butyllithium as well as from the reaction of the known titanocene-alkyne complex [Cp(2) Ti(η(2) -Me(3) SiC(2) SiMe(3) )] with the amine 1. Reactions of the lithium amide [(thf)(3) Li{N(PPh(2) )(2) }] with [Cp(2) MCl(2) ] (M=Zr, Hf) yielded the corresponding zirconocene and hafnocene complexes [Cp(2) M(Cl){κ(2) -N,P-N(PPh(2) )(2) }] (4 Zr and 4 Hf). Reduction of 4 Zr with magnesium gave the highly strained heterometallacycle [Cp(2) Zr(κ(2) -P,P-Ph(2) P-N-PPh(2) )] (3 Zr). Complexes 2, 3 Ti, 4 Hf, and 3 Zr were characterized by X-ray crystallography. The structures and bondings of all complexes were investigated by DFT calculations.

Molecular vibration spectroscopy studies on novel trinuclear rhodium-7-hydride complexes of the general type {[Rh(PP*)X]3(µ(2-X)3(µ3-X)}(BF4)2 (X = H, D).

Novel trinuclear rhodium-hydride complexes with diphosphine ligands Tangphos, t-Bu-BisP*, and Me-DuPHOS which contain bridging µ(2)- and µ(3)-hydrides as well as terminal hydrides in one molecule have been reported recently. In this work, these different rhodium-hydride bonds are characterized by Raman spectroscopy and the results are compared with those obtained by means of the more commonly applied IR spectroscopy. Density functional theory (DFT) calculations have been carried out to support the experimental findings. The structure of the Rh(3)H(7) core is described in the context of their vibrational stretching modes.

Implementation of Perforated Concentric Ring Walls Considerably Improves Gas-Liquid Mass Transfer of Shaken Bioreactors.

Since their first use in the 1930s, shake flasks have been a widely used bioreactor type for screening and process development due to a number of advantages. However, the limited gas-liquid mass transfer capacities-resulting from practical operation limits regarding shaking frequency and filling volumes-are a major drawback. The common way to increase the gas-liquid mass transfer in shake flasks with the implementation of baffles is generally not recommended as it comes along with several severe disadvantages. Thus, a new design principle for shaken bioreactors that aims for improving the gas-liquid mass transfer without losing the positive characteristics of unbaffled shake flasks is introduced. The flasks consist of cylindrical glass vessels with implemented perforated concentric ring walls. The ring walls improve the gas-liquid mass transfer via the formation of additional liquid films on both of its sides, whereas the perforations allow for mixing between the compartments. Sulfite oxidation experiments revealed over 200% higher maximum oxygen transfer capacities (OTRmax) compared to conventional shake flasks. In batch cultivations of Escherichia coli BL21 in mineral media, unlimited growth until glucose depletion and oxygen transfer rates (OTR) of up to 138 mmol/L/h instead of an oxygen limitation at 57 mmol/L/h as in normal shake flasks under comparable conditions could be achieved. Even overflow metabolism could be prevented due to sufficient oxygen supply without the use of unconventional shaking conditions or oxygen enrichment. Therefore, we believe that the new perforated ring flask principle has a high potential to considerably improve biotechnological screening and process development steps.

Potential errors in conventional DOT measurement techniques in shake flasks and verification using a rotating flexitube optical sensor.

BACKGROUND: Dissolved oxygen tension (DOT) is an important parameter for evaluating a bioprocess. Conventional means to measure DOT in shake flasks using fixed Clark-type electrodes immersed in the bulk liquid are problematic, because they inherently alter the hydrodynamics of the systems. Other approaches to measure DOT that apply fluorescing sensor spots fixed at the inside wall of a shake flask are also suboptimal. At low filling volumes for cultivating microorganisms with a high oxygen demand, the measured DOT signal may be erroneous. Here, the sensor spot is sometimes exposed to gas in the head space of the flask. Merely repositioning the sensor spot elsewhere in the flask does not address this problem, since there is no location in the shake flask that is always covered by the rotating bulk liquid. Thus, the aim of this prospective study is first, to verify the systemic error of Clark-type electrodes for measuring DOT in shake flasks. The second principle aim is to use the newly built "flexitube optical sensor" to verify potential errors in conventional optical DOT measurements based on fixed sensor spots. RESULTS: With the Clark-type electrode, the maximum oxygen transfer capacity in shake flasks rose compared to that of an analogous system without an electrode. This proves changed hydrodynamics in the system with the Clark-type electrode. Furthermore, regarding the sensor spot experiments under oxygen-limited conditions where the DOT value ought to approach zero, the acquired signals were clearly above zero. This implies that the sensor spot is influenced by oxygen present in the headspace and not only by oxygen in the bulk liquid. CONCLUSIONS: The Clark-type electrode is unsuitable for measuring DOT. Moreover, the newly built rotating flexitube optical sensor is useful to verify potential errors of conventional optical DOT measurement techniques applying fixed sensor spots.

A New Three-Component Photo-Initiating System for Visible Light Recording of Volume Holograms with Single-Pulsed Laser.

Versatile substituted electron-deficient trichloromethylarenes can easily be synthesized and combined with a Safranine O/triarylalkylborate salt to form a highly efficient three-component photo-initiation system that starts free radical polymerization to finally form holographic gratings with a single-pulsed laser. The mechanism of this photo-initiation most likely relies on an electron transfer from the borate salt into the semi-occupied HOMO of the excited dye molecule Safranine O, which after fragmentation generates an initiating alkyl radical and longer-lived dye radical species. This dye radical is most probably oxidized by the newly introduced trichloromethylarene derivative as an electron acceptor. The two generated radicals from one absorbed photon initiate the photopolymerization and form index gratings in a suitable holographic recording material. This process is purely photonic and does not require further non-photonic post treatments.

Si-H bond activation of alkynylsilanes by group 4 metallocene complexes.

The reactivity of variously substituted alkynylsilanes toward selected group 4 metallocene complexes was investigated. Reactions of the alkynylsilanes R(1)C(2)SiR(2)(2)H (R(1) = SiMe(3), R(2) = Me, 1; R(1) = SiMe(3), R(2) = Ph, 2; R(1) = SiMe(2)H, R(2) = Me, 5) with Cp(2)TiMe(2) (Cp = eta(5)-cyclopentadienyl) resulted, upon methyl group transfer to the silyl group, in the previously described titanocene alkyne complexes Cp(2)Ti(R(1)C(2)SiR(2)(2)R(3)) (R(1) = Me(3)Si, R(2) = R(3) = Me, 3; R(1) = HMe(2)Si, R(2) = R(3) = Me, 6) or the unreported complex 4 (R(1) = Me(3)Si, R(2) = Ph, R(3) = Me). The Cp(2)TiCl(2)/n-BuLi system yielded alkyne complexes 6 and 7 (R(1) = HMe(2)Si, R(2) = Me, R(3) = H); no alkyl group transfer was detected. On the other hand, reactions utilizing the Cp(2)ZrCl(2)/n-BuLi system afforded inseparable mixtures; however, complexes of the type Cp(2)Zr[R(1)C(2)SiMe(2)(n-Bu)] (R(1) = Me(3)Si, 8; R(1) = HMe(2)Si, 9) were detected. Cp(2)Hf(n-Bu)(2) reacted with the alkynylsilanes in a diverse way, depending on the substituents of the alkyne substrate. The reaction with an excess of alkyne 1 (R(1) = Me(3)Si, R(2) = Me) afforded only an intractable mixture, which contained Me(3)SiC(2)SiMe(2)(n-Bu) (10). Hafnacyclopentadienes 13-15 as precedented product types were obtained when alkyne 12 (R(1) = Ph, R(2) = Me) was used. In sharp contrast, the symmetrically substituted alkynes 5 (R(1) = HMe(2)Si, R(2) = Me) and H(2)PhSiC(2)SiPhH(2) (18) yielded the hitherto unknown Si-containing metallacycles 16 and 19. A reaction mechanism leading to these products was proposed and subsequently supported by DFT calculations. In addition, the reduction of Cp(2)HfCl(2) with magnesium in THF in the presence of alkynylsilanes was shown to be an alternative route to compounds 14-16 and 19. Presumably due to steric reasons, alkyne 1 could not form any of the product types described above. Nevertheless, it was utilized for the preparation of the PMe(3)-stabilized hafnocene alkyne complex 11.

Formation of a 1-zircona-2,5-disilacyclopent-3-yne: coordination of 1,4-disilabutatriene to zirconocene?

Alkyne under stress: a novel metallacycle containing one Zr atom, two Si atoms, and a C≡C bond has been prepared and its structure elucidated (Zr green, Si blue, C gray). According to X-ray data, spectral properties, and DFT calculations, the bonding situation in this compound is characterized as a 1-metalla-2,5-disilacyclopent-3-yne with a weak metal-triple-bond interaction.

Heart rate variability as a measure of autonomic regulation of cardiac activity for assessing stress and welfare in farm animals -- a review.

Measurement of heart rate variability (HRV) is a non-invasive technique that can be used to investigate the functioning of the autonomic nervous system, especially the balance between sympathetic and vagal activity. It has been proven to be very useful in humans for both research and clinical studies concerned with cardiovascular diseases, diabetic autonomic dysfunction, hypertension and psychiatric and psychological disorders. Over the past decade, HRV has been used increasingly in animal research to analyse changes in sympathovagal balance related to diseases, psychological and environmental stressors or individual characteristics such as temperament and coping strategies. This paper discusses current and past HRV research in farm animals. First, it describes how cardiac activity is regulated and the relationships between HRV, sympathovagal balance and stress and animal welfare. Then it proceeds to outline the types of equipment and methodological approaches that have been adapted and developed to measure inter-beats intervals (IBI) and estimate HRV in farm animals. Finally, it discusses experiments and conclusions derived from the measurement of HRV in pigs, cattle, horses, sheep, goats and poultry. Emphasis has been placed on deriving recommendations for future research investigating HRV, including approaches for measuring and analysing IBI data. Data from earlier research demonstrate that HRV is a promising approach for evaluating stress and emotional states in animals. It has the potential to contribute much to our understanding and assessment of the underlying neurophysiological processes of stress responses and different welfare states in farm animals.

John Brown's system of medicine and its introduction in Denmark around 1800.

At the end of the eighteenth century a scientific basis for medicine was called for. The Scottish physician John Brown proposed an all-comprising medical system in 1780. A surplus or lack of stimulating factors, the prime movers of life according to Brown, was supposed to explain all diseases and indicate their treatment. Individuals only subjected to a small degree of stimulation became affected by "asthenic diseases" which were the most frequent diseases. They should be treated with abundant food and wine, supplemented with camphor, opium, or other drugs considered to be stimulating. Conversely, individuals with "sthenic diseases" should reduce their intake of food and beverage. Brown's system was received with transient approval by some Danish physicians from the late 1790s. But it soon proved to be of no value in medical practice, and its success dwindled within academic medicine around 1814. On the other hand, it seemed to generate new ideas. It became linked with the German Romantic Movement and "Naturphilosophie." The widespread use of camphor and opium in both academic and folk medicine, continued throughout the nine- teenth century and into the twentieth century.

["The Society for letters and natural science" The young Ole H. Mynster and the chemical revolution around 1800]. / "Det Litteraire og Naturforskende Selskab". Den unge Ole H. Mynster og den kemiske revolution omkring 1800.

Ole H. Mynster (1772-1818) was a stepson of the leading physician at the Royal Frederik Hospital in Copenhagen. At an early age he became fond of zoology and mineralogy. He created "societies" in Enlightenment-style for boys and young people with lectures and collections. Later on a circle of talented young students, scientists and poets met in his small room at the hospital. Some of them with Ole Mynster as the head set up a modern scientific journal, Physicalsk, oeconomisk og medicochirurgisk Bibliotek for Danmark og Norge which encouraged the introduction of antiphlogistic chemistry. Ole Mynster became physician at the Royal Frederik Hospital and lecturer in clinical pharmacology. He wrote the first book in Danish on pharmacology based upon chemistry. In their memoirs, prominent members of his circle have told about him, and his son F.L. Mynster has written a draft for a biography. An overview of the activities within natural science and medicine of the young Ole Hieronymus Mynster is presented.

[A case of Yellow fever in 1887]. / Et tilfælde af gul feber i 1887.

A young Danish sailor died from yellow fever in Barbados in 1887. The Shipmaster's letter to the family with a description of the course of the disease, which has been preserved, is presented here together with a photo of the sailor and a painting of the Danish sailing-ship.

[A birth with fatal outcome in 1866]. / En fatalt forløbende fødsel i 1866. En kasuistik med illustrationer.

A birth with fatal outcome for both the mother and the foetus was reported in the Danish medical journal, Bibliothek for Læger in 1868. Here, the article with its two illustrations is summarised because of the vivid description of the course together with the therapeutic considerations expressed by the obstetrician. Due to an earlier osteomyelitis the pregnant woman's spine was deformed and her pelvis was narrowed. The birth came to a standstill, and it became necessary to reduce the circumference of the foetus' cranium by perforation, after which the dead foetus could be delivered. The woman died of infection some days later. Afterwards her deformed lumbar spine and pelvis was removed, preserved and depicted in two lithographs. The preserved pelvis is still extant in the Saxtorphian obstetric collection in Medical Museion, Copenhagen.

[A reading of Foucault's "The Birth of the Clinic"]. / En læsning af Michel Foucaults "Klinikkens fødsel".

The starting point for Foucault's book was his wide reading of French medical literature from late 18th and early 19th centuries. He showed how the concept of disease changed profoundly during that period of great societal changes. Foucault's protagonists in the book were the French doctors Pinel, Bichat, Laënnec and Broussais. Here, short biographies and summaries of their works will be presented in the medical and historical context and together with extracts of Foucault's text.