Acylated Inulin as a Potential Shale Hydration Inhibitor in Water Based Drilling Fluids for Wellbore Stabilization.

Shale hydration dispersion and swelling are primary causes of wellbore instability in oil and gas reservoir exploration. In this study, inulin, a fructo-oligosaccharide extracted from Jerusalem artichoke roots, was modified by acylation with three acyl chlorides, and the products (C10-, C12-, and C14-inulin) were investigated for their use as novel shale hydration inhibitors. The inhibition properties were evaluated through the shale cuttings hot-rolling dispersion test, the sodium-based bentonite hydration test, and capillary suction. The three acylated inulins exhibited superb hydration-inhibiting performance at low concentrations, compared to the commonly used inhibitors of KCl and poly (ester amine). An inhibition mechanism was proposed based on surface tension measurements, contact angle measurements, Fourier-transform infrared analysis, and scanning electron microscopy. The acylated inulin reduced the water surface tension significantly, thus, retarding the invasion of water into the shale formation. Then, the acylated inulin was adsorbed onto the shale surface by hydrogen bonding to form a compact, sealed, hydrophobic membrane. Furthermore, the acylated inulins are non-toxic and biodegradable, which meet the increasingly stringent environmental regulations in this field. This method might provide a new avenue for developing high-performance and ecofriendly shale hydration inhibitors.

Effect of Chemical Composition of Metal-Organic Crosslinker on the Properties of Fracturing Fluid in High-Temperature Reservoir.

To investigate the effect of the chemical composition of a metal-organic crosslinker on the performances of fracturing fluid in high-temperature conditions, four zirconium (Zr) crosslinkers and one aluminum-zirconium (Al-Zr) crosslinker with a polyacrylamide were used. The crosslinkers possessed the same Zr concentration, but they differed in component amounts and the order of the addition of the crosslinker components, leading to different chemical compositions in the crosslinkers. The fracturing fluids prepared by different tested crosslinkers were compared in terms of properties of rheological behavior, sand-carrying ability, microstructure, and gel breaking characteristics. The results showed that the fracturing fluids prepared by zirconium lactic acid, ethanediamine, and sorbitol crosslinkers offered the slowest viscosity development and highest final viscosity compared to the zirconium lactic acid crosslinker and the zirconium lactic acid and ethanediamine crosslinker. The zirconium sorbitol, lactic acid, and ethanediamine crosslinker exhibited a faster crosslinking rate and a higher final viscosity than the zirconium lactic acid, ethanediamine, and sorbitol crosslinker; the crosslinker showed crosslinking density and crosslinking reactivity, resulting in more crosslinking sites and a higher strength in the fracturing fluid. The Al-Zr-based crosslinker possessed better properties in temperature and shear resistance, viscoelasticity, shear recovery, and sand-carrying ability than the Zr-based crosslinker due to the synergistic crosslinking effect of aluminum and zirconium ions. The tertiary release gelation mechanism of the Al-Zr-based fracturing fluid achieved a temperature resistance performance in the form of continuous crosslinking, avoiding the excessive crosslinking dehydration and reducing viscosity loss caused by early shear damage. These results indicated that the chemical compositions of metal-organic crosslinkers were important factors in determining the properties of fracturing fluids. Therefore, the appropriate type of crosslinker could save costs without adding the additional components required for high-temperature reservoirs.

Fracturing Fluid Polymer Thickener with Superior Temperature, Salt and Shear Resistance Properties from the Synergistic Effect of Double-Tail Hydrophobic Monomer and Nonionic Polymerizable Surfactant.

To develop high-salinity, high-temperature reservoirs, two hydrophobically associating polymers as fracturing fluid thickener were respectively synthesized through aqueous solution polymerization with acrylamide (AM), acrylic acid (AA), 2-acrylamido-2-methylpropanesulfonic acid (AMPS), nonionic polymerizable surfactant (NPS) and double-tail hydrophobic monomer (DHM). The thickener ASDM (AM/AA/AMPS/NPS/DHM) and thickener ASD (AM/AA/AMPS/DHM) were compared in terms of properties of water dissolution, thickening ability, rheological behavior and sand-carrying. The results showed that ASDM could be quickly diluted in water within 6 min, 66.7% less than that of ASD. ASDM exhibited salt-thickening performance, and the apparent viscosity of 0.5 wt% ASDM reached 175.9 mPa·s in 100,000 mg/L brine, 100.6% higher than that of ASD. The viscosity of 0.5 wt% ASDM was 85.9 mPa·s after shearing for 120 min at 120 °C and at 170 s-1, 46.6% higher than that of ASD. ASDM exhibited better performance in thickening ability, viscoelasticity, shear recovery, thixotropy and sand-carrying than ASD. The synergistic effect of hydrophobic association and linear entanglement greatly enhancing the performance of ASDM and the compactness of the spatial network structure of the ASDM was enhanced. In general, ASDM exhibited great potential for application in extreme environmental conditions with high salt and high temperatures.

Clinical efficacy and safety of robotic distal gastrectomy for gastric cancer: a systematic review and meta-analysis.

BACKGROUND: Robotic distal gastrectomy (RDG) is a new technique that is rapidly gaining popularity and may help overcome the limitations of laparoscopic distal gastrectomy (LDG); however, its safety and therapeutic efficacy remain controversial. Therefore, this meta-analysis was performed to evaluate the safety and efficacy of RDG. METHODS: We searched PubMed, EMBASE, the Cochrane Library, and Web of Science for studies that compared RDG and LDG and were published between the time of database inception and May 2021. We assessed the bias risk of the observational studies using ROBIN-I, and a random effect model was always applied. RESULTS: The meta-analysis included 22 studies involving 5386 patients. Compared with LDG, RDG was associated with longer operating time (Mean Difference [MD] = 43.88, 95% CI = 35.17-52.60), less intraoperative blood loss (MD = - 24.84, 95% CI = - 41.26 to - 8.43), a higher number of retrieved lymph nodes (MD = 2.41, 95% CI = 0.77-4.05), shorter time to first flatus (MD = - 0.09, 95% CI = - 0.15 to - 0.03), shorter postoperative hospital stay (MD = - 0.68, 95% CI = - 1.27 to - 0.08), and lower incidence of pancreatic fistula (OR = 0.23, 95% CI = 0.07-0.79). Mean proximal and distal resection margin distances, time to start liquid and soft diets, and other complications were not significantly different between RDG and LDG groups. However, in the propensity-score-matched meta-analysis, the differences in time to first flatus and postoperative hospital stay between the two groups lost significance. CONCLUSIONS: Based on the available evidence, RDG appears feasible and safe, shows better surgical and oncological outcomes than LDG and, comparable postoperative recovery and postoperative complication outcomes.

Assessment of a novel aminated magnetic adsorbent with excellent adsorption capacity for dyes and drugs.

Dyes and drugs with high toxicity and low biodegradability pose risk to human health and ecological security, and should be purified efficiently from effluents before discharge. Traditional adsorbents are limited by the insufficient active adsorption sites and low stability. In this study, a novel aminated magnetic adsorbent (MCTs) was fabricated via two cross-linking steps using chitosan and triethylenetetramine to fill the gaps between current adsorbent and performance requirements. The morphological and physicochemical characteristics of the as-prepared MCTs were determined and identified with the aid of several characterization techniques. The adsorption performance of dyes and drugs was also investigated and represented by their adsorption capacities. In particular, the adsorption capacities of Congo Red, Chicago Sky Blue, Reactive Brilliant Red, and Ibuprofen were 583.11, 465.01, 403.12, and 291.71 mg/g, respectively. They also remained at around 80% after four reuse cycles. MCTs were adsorbed via a monolayer spontaneous chemical reaction, and hydrogen bonding and electrostatic interaction were the dominant adsorption mechanisms. These results demonstrated that the preparation of MCTs via two cross-linking steps enhanced the adsorbents' adsorption capacity, reusability, and stability. They provided a new perspective for the preparation of high-efficient adsorbents and the purification of dye- and drug-polluted wastewater.

A fluorometric optical fiber nanoprobe for copper(II) by using AgInZnS quantum dots.

An optical fiber nanoprobe is presented for fluorometric determination of copper(II). The method based on the use of water-dispersible AgInZnS quantum dots (QDs) deposited at the end of an optical fiber in a poly(vinyl alcohol) matrix. The fluorescnece of the QDs, best measured at excitation/emisssion wavelengths of 365/570 nm, is quenched by Cu(II) due to both static and electron transfer from the QDs to Cu(II). This is experimentally confirmed by photoluminescence and UV-vis absorption spectra, and measurement of luminescence lifetimes. The probe is highly selective and possesses a linear detection range that extends from 2.5 to 800 nM. Graphical abstractSchematic representation of an optical fiber nanoprobe based on hydrophilic AgInZnS quantum dots for fluorometric determination of copper(II). The fluorescence is quenched by Cu(II) due to static quenching and dynamic quenching. It has a detection range of 2.5-800 nM.

Distributed vibration measurement based on a coherent multi-slope-assisted BOTDA with a large dynamic range.

We propose a novel technique to enhance the dynamic range of a coherent slope-assisted Brillouin optical time domain analysis. A multi-tone probe and a reference wave are launched into the fiber under test (FUT); after interacting with the pump pulse, the Brillouin gain, as well as the Brillouin phase shift of each tone, can be demodulated simultaneously. In light of this, the strain information can be determined by the Brillouin phase-gain ratio of each tone. In the experiment, a three-tone probe with a 60 MHz interval is used; effective measurement frequency span larger than 180 MHz is verified in a ∼2 km single-mode fiber with 2.5 m spatial resolution and 1.5 kHz sampling rate to strain. A vibration signal with 41 Hz frequency and 2546 µÎµ amplitude is successfully demodulated.

Nitrogen doped graphene quantum dots as a fluorescent probe for mercury(II) ions.

A highly selective fluorescent probe for Hg2+ is reported. It consists of nitrogen doped graphene quantum dots (NGQDs) that are nearly spherical in shape, have an average diameter of 2.7 nm and excitation-independent emission. The blue fluorescence of the NGQDs (with maximum excitation/emission at 378/447 nm) is quenched by Hg2+ due to both dynamic and static quenching. The probe has a wide detection range (2.5 µM - 800 µM) and a limit of detection of 2.5 µM. The dynamic and static quenching constants are 417 M-1 and 63500 M-1, respectively. The probe was used to quantfy Hg2+ in spiked real water samples with satisfactory results. Graphical abstract ᅟ.

The pomegranate (Punica granatum L.) genome provides insights into fruit quality and ovule developmental biology.

Pomegranate (Punica granatum L.) has an ancient cultivation history and has become an emerging profitable fruit crop due to its attractive features such as the bright red appearance and the high abundance of medicinally valuable ellagitannin-based compounds in its peel and aril. However, the limited genomic resources have restricted further elucidation of genetics and evolution of these interesting traits. Here, we report a 274-Mb high-quality draft pomegranate genome sequence, which covers approximately 81.5% of the estimated 336-Mb genome, consists of 2177 scaffolds with an N50 size of 1.7 Mb and contains 30 903 genes. Phylogenomic analysis supported that pomegranate belongs to the Lythraceae family rather than the monogeneric Punicaceae family, and comparative analyses showed that pomegranate and Eucalyptus grandis share the paleotetraploidy event. Integrated genomic and transcriptomic analyses provided insights into the molecular mechanisms underlying the biosynthesis of ellagitannin-based compounds, the colour formation in both peels and arils during pomegranate fruit development, and the unique ovule development processes that are characteristic of pomegranate. This genome sequence provides an important resource to expand our understanding of some unique biological processes and to facilitate both comparative biology studies and crop breeding.

Polarization independent fast BOTDA based on pump frequency modulation and cyclic coding.

We propose and experimentally demonstrate a scheme of polarization independent fast Brillouin optical time domain analysis (F-BOTDA) based on pump frequency modulation and cyclic coding. The Brillouin gain spectrum (BGS) is reconstructed by fast scanning frequency of the pump using an arbitrary waveform generator (AWG). To realize long range distributed dynamic strain sensing, polarization diversity technique and cyclic coding are employed to eliminate polarization fading and enhance the signal-to-noise ratio (SNR). Based on this configuration, the need of trace averaging is avoided, sensing speed of 440 Hz is achieved over ~2 km single mode fiber with 50 scanning frequencies and a spatial resolution of 1.5 m. Vibration events up to 40 Hz are successfully identified.

An in Vitro Study on the Effect of Combined Treatment with Photodynamic and Chemical Therapies on Candida albicans.

Candida albicans is the most commonly encountered human fungal pathogen, and it is traditionally treated with antimicrobial chemical agents. The antimicrobial effect of these agents is largely weakened by drug resistance and biofilm-associated virulence. Enhancement of the antimicrobial activity of existing agents is needed for effective candidiasis treatment. Our aim was to develop a therapy that combined biofilm disruption with existing antimicrobial agents. Photodynamic therapy (PDT) utilizing curcumin and blue light was tested as an independent therapy and in combination with fluconazole treatment. Viability assays and morphology analysis were used to assess the effectiveness of C. albicans treatment. Results showed that fluconazole treatment decreased the viability of planktonic C. albicans, but the decrease was not as pronounced in adherent C. albicans because its biofilm form was markedly more resistant to the antimicrobiotic. PDT effectively eradicated C. albicans biofilms, and when combined with fluconazole, PDT significantly inhibited C. albicans to a greater extent. This study suggests that the addition of PDT to fluconazole to treat C. albicans infection enhances its effectiveness and can potentially be used clinically.

Tens of hertz narrow-linewidth laser based on stimulated Brillouin and Rayleigh scattering.

We proposed and demonstrated a linewidth compression method of a laser based on stimulated Brillouin scattering (SBS) and a Rayleigh backscattering structure (RBS). The relationship between the output SBS laser linewidth and the input pump linewidth was studied theoretically and experimentally. It is shown that the narrower linewidth of the pump laser leads to the narrower bandwidth of the SBS gain and, finally, the bandwidth of the SBS will tend to its intrinsic value as the linewidth of a pump laser narrower than 10 kHz; then the linewidth of an SBS fiber ring laser would tend to 200 Hz. In order to further reduce its linewidth with low cost, RBS and a simple dual-cavity feedback structure were added and, finally, a ∼75 Hz narrow-linewidth laser with a side-mode suppression ratio of 70 dB was obtained.

Property of Modified Bovine Bone Glue as an Environmental Additive in Water-Based Drilling Fluids.

At present, animal bone glue (BG) is being widely used in many fields, but there are no studies reported on oilfield chemistry. In this paper, an environmental water-based drilling fluids additive named bromoethane-modified bone glue (BG) was developed by using bovine bone glue and bromoethane as raw materials, anhydrous ethanol as solvent, sodium hydroxide as alkaline hydrolysis agent, and sodium carbonate as a system pH regulator. The inhibition, filtration performance, and temperature resistance of BG were evaluated. Performance study results show that the linear swelling rate of sodium bentonite (Na-MMT) was decreased from 50.2% (in tap water) to 38.2% (in 4 wt % BG solutions), and filtration loss was reduced from 30 mL (in tap water) to 12 mL (in 5 wt % BG). Hot-rolling experiments show that the BG solution still exhibits good performance even after 16 h × 130 °C. The reasons for BG to achieve excellent performance were analyzed through scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), ζ potential, thermogravimetric analysis (TGA), and microstructure. The results of SEM and FT-IR show that BG can fully dissolve in water and adsorb on the surface of clay particles by relying on its own adsorption functional groups such as -OH and -COOH. When 4% BG was added, ζ potential analysis revealed that the clay particle size declined by 0.502 µm, which indicated that BG can inhibit clay hydration swelling dispersion.

Preparation and Performance Evaluation of Ionic Liquid Copolymer Shale Inhibitor for Drilling Fluid Gel System.

An inhibitor that can effectively inhibit shale hydration is necessary for the safe and efficient development of shale gas. In this study, a novel ionic liquid copolymer shale inhibitor (PIL) was prepared by polymerizing the ionic liquid monomers 1-vinyl-3-aminopropylimidazolium bromide, acrylamide, and methacryloyloxyethyl trimethyl ammonium chloride. The chemical structure was characterized using fourier transform infrared spectroscopy (FT-IR) and hydrogen-nuclear magnetic resonance (H-NMR), and the inhibition performance was evaluated using the inhibition of slurrying test, bentonite flocculation test, linear expansion test, and rolling recovery test. The experimental results showed that bentonite had a linear expansion of 27.9% in 1 wt% PIL solution, 18% lower than that in the polyether amine inhibitor. The recovery rate of shale in 1 wt% PIL was 87.4%. The ionic liquid copolymer could work synergistically with the filtrate reducer, reducing filtration loss to 7.2 mL with the addition of 1%. Mechanism analysis showed that PIL adsorbed negatively charged clay particles through cationic groups, which reduced the electrostatic repulsion between particles. Thus, the stability of the bentonite gel systems was destroyed, and the hydration dispersion and expansion of bentonite were inhibited. PIL formed a hydrophobic film on the surface of clay and prevented water from entering into the interlayer of clay. In addition, PIL lowered the surface tension of water, which prevented the water from intruding into the rock under the action of capillary force. These are also the reasons for the superior suppression performance of PIL.

Development of a Low-Molecular-Weight Filtrate Reducer with High-Temperature Resistance for Drilling Fluid Gel System.

Currently, conventional polymeric filtrate reducers with high-temperature resistance for use in drilling fluids have high molecular weights, which greatly affects the rheological properties. Therefore, to address the challenges in regulating the rheology and filtration performance of high-density drilling fluids at high temperatures, it is essential to develop low-molecular-weight filtrate reducers with high-temperature resistance. In this study, a low-molecular-weight filtrate reducer with high-temperature resistance (LMF) was prepared via free radical polymerization from acrylamide and 2-acrylamido-2-methyl-1-propanesulfonic acid as monomers, tertiary dodecyl mercaptan as a chain transfer agent, and ammonium persulfate as the initiator. LMF was then characterized by infrared spectroscopy, thermogravimetric analysis, and gel permeation chromatography. The obtained filtrate reducer exhibits a weight-average molecular weight (Mw) of 3819 and an initial thermal decomposition temperature of 300.7 °C, indicating good thermal stability. The effects of LMF dosage, temperature, and NaCl dosage on the rheology and filtration performance of mud samples were also investigated, and the mechanism of action was revealed by zeta potential, particle size distribution, scanning electron microscopy, and adsorption measurements. The results reveal that LMF increases the mud sample viscosity and reduces its filtration. For example, the filtration of the mud sample with 2 wt% LMF was 7.2 mL, a reduction of 70% compared to that of a blank mud sample. Further, after aging at 210 °C for 16 h, the filtration of the same sample was 11.6 mL, and that of a mud sample with 2 wt% LMF and 35 wt% NaCl after aging at 180 °C for 16 h was 22 mL. Overall, we have reported a scheme to prepare a low-molecular-weight filtrate reducer with high-temperature resistance and superior filtrate-reducing effects, laying the foundation for the investigation and development of low-molecular-weight filtrate reducers.

Transformation of tetracycline by multipurpose Fe-Mn-Cu nano-composite oxide: Dual-synergies and dual-mechanisms.

The interaction between tetracycline (TTC) and mixed metallic oxides remains unclear, and even complexation usually is ignored. This study firstly distinguished the triple functions of adsorption, transformation and complexation in presence of Fe-Mn-Cu nano-composite metallic oxide (FMC) on TTC. Rapid adsorption and faint complexation initiated the transformation that dominated the entire reactions at 180 min, which completed TTC removal (up to 99.04%) synergistically within 48 h. Environmental factors (dosage, pH and coexisting ions) had small influence on TTC removal, which primarily depended on the stable transformation characteristics of FMC. Kinetic models incorporating pseudo-second-order kinetics and transformation reaction kinetics demonstrated that the surface sites of FMC promoted electron transfer process through chemical adsorption and electrostatic attraction. ProtoFit program coupled with characterization methods concluded that Cu-OH was the main reaction site of FMC where the protonated surface favored to generate·O2-. Meanwhile, three metal ions developed simultaneous mediated transformation reactions on TTC in liquid phase, and·O2- induced the production of·OH. The transformed products were subjected to toxicity assessment, which had lost antimicrobial properties toward Escherichia coli. Insights gained from this study can refine the dual mechanisms of multipurpose FMC in solid and liquid phases underlying TTC transformation.

Effect of Low Gravity Solids on Weak Gel Structure and the Performance of Oil-Based Drilling Fluids.

Drilling cuttings from the rock formation generated during the drilling process are generally smashed to fine particles through hydraulic cutting and grinding using a drilling tool, and then are mixed with the drilling fluid during circulation. However, some of these particles are too small and light to be effectively removed from the drilling fluid via solids-control equipment. These small and light solids are referred to as low gravity solids (LGSs). This work aimed to investigate the effect of LGSs on the performance of oil-based drilling fluid (OBDF), such as the rheological properties, high-temperature and high-pressure filtration loss, emulsion stability, and filter cake quality. The results show that when the content of LGSs reached or even exceeded the solid capacity limit of the OBDF, the rheological parameters including the plastic viscosity, gel strength, and thixotropy of OBDF increased significantly. Furthermore, the filtration of OBDF increases, the filter cake becomes thicker, the friction resistance becomes larger, and the stability of emulsion of OBDF also decreases significantly when the concentration of LGSs reached the solid capacity limit of OBDF (6-9 wt% commonly). It was also found that LGSs with a smaller particle size had a more pronounced negative impact on the drilling fluid performance. This work provides guidance for understanding the impact mechanism of LGSs on drilling fluid performance and regulating the performance of OBDF.

Styrene-Lauryl Acrylate Rubber Nanogels as a Plugging Agent for Oil-Based Drilling Fluids with the Function of Improving Emulsion Stability.

With the exploration and development of unconventional oil and gas, the use frequency of oil-based drilling fluid (ODF) is increasing gradually. During the use of ODFs, wellbore instability caused by invasion of drilling fluid into formation is a major challenge. To improve the plugging property of ODFs, nano-sized poly(styrene-lauryl acrylate) (PSL) rubber nanogels were synthesized using styrene and lauryl acrylate through soap-free emulsion polymerization method and were characterized using FTIR, NMR, SEM, TEM, particle size analysis and TGA. The results show that, due to good dispersion stability and oil-absorbing expansion ability, the PSL rubber nanogels have a wide range of adaptations for nano-scale pores to deposit a layer of dense filter cake on the surface of filter paper with various pore diameters, reducing the filtration of mineral oil and W/O emulsion significantly. Due to the unique wettability, the PSL rubber nanogels can be adsorbed stably at the oil-water interface and form a dense granular film to prevent droplets coalescing, which improves the emulsification stability of W/O emulsion. Furthermore, the PSL rubber nanogels are soap-free and compatible with ODFs without foaming problems. The PSL rubber nanogels can increase the hole-cleaning performance of ODFs by raising viscosity and yield point. The PSL rubber nanogels outperformed hydrophobic modified nano silica and polystyrene nanospheres in plugging and filtration reduction. Therefore, the PSL rubber nanogels are expected to be used as a new plugging agent in oil-based drilling fluid. This research provide important insights for the use of organic nanogels in ODFs and the optimization of plugging conditions.

A Thermal-Responsive Zwitterionic Polymer Gel as a Filtrate Reducer for Water-Based Drilling Fluids.

It is crucial to address the performance deterioration of water-based drilling fluids (WDFs) in situations of excessive salinity and high temperature while extracting deep oil and gas deposits. The focus of research in the area of drilling fluid has always been on filter reducers that are temperature and salt resistant. In this study, a copolymer gel (PAND) was synthesized using acrylamide, N-isopropyl acrylamide, and 3-dimethyl (methacryloyloxyethyl) ammonium propane sulfonate through free-radical polymerization. The copolymer gel was then studied using FTIR, NMR, TGA, and element analysis. The PAND solution demonstrated temperature and salt stimulus response characteristics on rheology because of the hydrophobic association effect of temperature-sensitive monomers and the anti-polyelectrolyte action of zwitterionic monomers. Even in conditions with high temperatures (180 °C) and high salinities (30 wt% NaCl solution), the water-based drilling fluid with 1 wt% PAND displayed exceptional rheological and filtration properties. Zeta potential and scanning electron microscopy (SEM) were used to investigate the mechanism of filtration reduction. The results indicated that PAND could enhance bentonite particle colloidal stability, prevent bentonite particle aggregation, and form a compact mud cake, all of which are crucial for reducing the filtration volume of water-based drilling fluid. The PAND exhibit excellent potential for application in deep and ultra-deep drilling engineering, and this research may offer new thoughts on the use of zwitterionic polymer gel in the development of smart water-based drilling fluid.

Molecular Simulation of Interactions between High-Molecular-Polymer Flocculation Gel for Oil-Based Drilling Fluid and Clay Minerals.

China has abundant shale gas resources with great potential, which may serve as a significant support for the development of a "low-carbon economy". Domestic shale gas resources are buried deeply and difficult to exploit due to some prevalent issues, such as long horizontal sections, severe development of reservoir fractures, strong sensitivity to water, borehole instability, etc. Compared to water-based drilling fluids, oil-based drilling fluid exhibits better inhibition and good lubricity and is thus broadly used in shale gas drilling, but it is confronted with the challenge of removing the harmful solid phase. Selective chemical flocculation is one of the most effective methods of removing the harmful solid phase in oil-based drilling fluid. In this study, interactions between the flocculation gel for oil-based drilling fluid and clay minerals were investigated by molecular simulation, which revealed the molecular-scale selectivity of the flocculation gel for rock cuttings with negative charges. Calculations showed that the flocculation gel is highly effective for the flocculation of negatively charged cuttings, but it is ineffective for flocculating neutral cuttings. The flocculation gel is not very effective for cuttings with high hydrophilicity, and it is totally ineffective for flocculating cuttings with poor hydrophilicity. Within a limited concentration range, the flocculation effect can be enhanced by increasing the flocculation gel concentration. The performance of the flocculation gel declined at elevated temperatures.