Janus Graphene Liquid Crystalline Fiber with Tunable Properties Enabled by Ultrafast Flash Reduction.

Flash photothermal treatment via Xenon lamp with a broad wavelength spectrum can effectively remove oxygen functionalities and restore sp2 domains at graphitic carbon materials. The chemical composition and relevant structure formation of flash reduced graphene oxide liquid crystal (GOLC) fibers are investigated in accordance with flash irradiation conditions. Owing to the spatial controllability of reduction level via anisotropic flash irradiation, the mechanical properties and electrical conductivity of graphene fibers can be delicately counterbalanced to attain desired properties. High sensitivity humidity sensors can be fabricated from the flash reduced fibers demonstrating notably higher sensitivity over the thermally reduced counterparts. This ultrafast flash reduction holds great promise for multidimensional macroscopic GO based structures, enabling a wide range of potential applications, including textile electronics and wearable sensors.

Simultaneous emulation of synaptic and intrinsic plasticity using a memristive synapse.

Neuromorphic computing targets the hardware embodiment of neural network, and device implementation of individual neuron and synapse has attracted considerable attention. The emulation of synaptic plasticity has shown promising results after the advent of memristors. However, neuronal intrinsic plasticity, which involves in learning process through interactions with synaptic plasticity, has been rarely demonstrated. Synaptic and intrinsic plasticity occur concomitantly in learning process, suggesting the need of the simultaneous implementation. Here, we report a neurosynaptic device that mimics synaptic and intrinsic plasticity concomitantly in a single cell. Threshold switch and phase change memory are merged in threshold switch-phase change memory device. Neuronal intrinsic plasticity is demonstrated based on bottom threshold switch layer, which resembles the modulation of firing frequency in biological neuron. Synaptic plasticity is also introduced through the nonvolatile switching of top phase change layer. Intrinsic and synaptic plasticity are simultaneously emulated in a single cell to establish the positive feedback between them. A positive feedback learning loop which mimics the retraining process in biological system is implemented in threshold switch-phase change memory array for accelerated training.

Biomimetic and flexible piezoelectric mobile acoustic sensors with multiresonant ultrathin structures for machine learning biometrics.

Flexible resonant acoustic sensors have attracted substantial attention as an essential component for intuitive human-machine interaction (HMI) in the future voice user interface (VUI). Several researches have been reported by mimicking the basilar membrane but still have dimensional drawback due to limitation of controlling a multifrequency band and broadening resonant spectrum for full-cover phonetic frequencies. Here, highly sensitive piezoelectric mobile acoustic sensor (PMAS) is demonstrated by exploiting an ultrathin membrane for biomimetic frequency band control. Simulation results prove that resonant bandwidth of a piezoelectric film can be broadened by adopting a lead-zirconate-titanate (PZT) membrane on the ultrathin polymer to cover the entire voice spectrum. Machine learning-based biometric authentication is demonstrated by the integrated acoustic sensor module with an algorithm processor and customized Android app. Last, exceptional error rate reduction in speaker identification is achieved by a PMAS module with a small amount of training data, compared to a conventional microelectromechanical system microphone.

A Flash-Induced Robust Cu Electrode on Glass Substrates and Its Application for Thin-Film µLEDs.

A robust Cu conductor on a glass substrate for thin-film µLEDs using the flash-induced chemical/physical interlocking between Cu and glass is reported. During millisecond light irradiation, CuO nanoparticles (NPs) on the display substrate are transformed into a conductive Cu film by reduction and sintering. At the same time, intensive heating at the boundary of CuO NPs and glass chemically induces the formation of an ultrathin Cu2 O interlayer within the Cu/glass interface for strong adhesion. Cu nanointerlocking occurs by transient glass softening and interface fluctuation to increase the contact area. Owing to these flash-induced interfacial interactions, the flash-activated Cu electrode exhibits an adhesion energy of 10 J m-2 , which is five times higher than that of vacuum-deposited Cu. An AlGaInP thin-film vertical µLED (VLED) forms an electrical interconnection with the flash-induced Cu electrode via an ACF bonding process, resulting in a high optical power density of 41 mW mm-2 . The Cu conductor enables reliable VLED operation regardless of harsh thermal stress and moisture infiltration under a high-temperature storage test, temperature humidity test, and thermal shock test. 50 × 50 VLED arrays transferred onto the flash-induced robust Cu electrode show high illumination yield and uniform distribution of forward voltage, peak wavelength, and device temperature.

Flash-Induced Stretchable Cu Conductor via Multiscale-Interfacial Couplings.

Herein, a novel stretchable Cu conductor with excellent conductivity and stretchability is reported via the flash-induced multiscale tuning of Cu and an elastomer interface. Microscale randomly wrinkled Cu (amplitude of ≈5 µm and wavelength of ≈45 µm) is formed on a polymer substrate through a single pulse of a millisecond flash light, enabling the elongation of Cu to exceed 20% regardless of the stretching direction. The nanoscale interlocked interface between the Cu nanoparticles (NPs) and the elastomer increases the adhesion force of Cu, which contributes to a significant improvement of the Cu stability and stretchability under harsh yielding stress. Simultaneously, the flash-induced photoreduction of CuO NPs and subsequent Cu NP welding lead to outstanding conductivity (≈37 kS cm-1) of the buckled elastic electrode. The 3D structure of randomly wrinkled Cu is modeled by finite element analysis simulations to show that the flash-activated stretchable Cu conductors can endure strain over 20% in all directions. Finally, the wrinkled Cu is utilized for wireless near-field communication on the skin of human wrist.

Laser-Material Interactions for Flexible Applications.

The use of lasers for industrial, scientific, and medical applications has received an enormous amount of attention due to the advantageous ability of precise parameter control for heat transfer. Laser-beam-induced photothermal heating and reactions can modify nanomaterials such as nanoparticles, nanowires, and two-dimensional materials including graphene, in a controlled manner. There have been numerous efforts to incorporate lasers into advanced electronic processing, especially for inorganic-based flexible electronics. In order to resolve temperature issues with plastic substrates, laser-material processing has been adopted for various applications in flexible electronics including energy devices, processors, displays, and other peripheral electronic components. Here, recent advances in laser-material interactions for inorganic-based flexible applications with regard to both materials and processes are presented.