Copper Adsorption on Lignin for the Removal of Hydrogen Sulfide.

Lignin is currently an underutilized part of biomass; thus, further research into lignin could benefit both scientific and commercial endeavors. The present study investigated the potential of kraft lignin as a support material for the removal of hydrogen sulfide (H2S) from gaseous streams, such as biogas. The removal of H2S was enabled by copper ions that were previously adsorbed on kraft lignin. Copper adsorption was based on two different strategies: either directly on lignin particles or by precipitating lignin from a solution in the presence of copper. The H2S concentration after the adsorption column was studied using proton-transfer-reaction mass spectrometry, while the mechanisms involved in the H2S adsorption were studied with X-ray photoelectron spectroscopy. It was determined that elemental sulfur was obtained during the H2S adsorption in the presence of kraft lignin and the differences relative to the adsorption on porous silica as a control are discussed. For kraft lignin, only a relatively low removal capacity of 2 mg of H2S per gram was identified, but certain possibilities to increase the removal capacity are discussed.

Antifouling properties of layer by layer DNA coatings.

Fouling is a major concern for solid/liquid interfaces of materials used in different applications. One approach of fouling control is the use of hydrophilic polymer coatings made from poly-anions and poly-cations using the layer-by-layer (LBL) method. The authors hypothesized that the poly-anionic properties and the poly-phosphate backbone of DNA would provide anti-biofouling and anti-scaling properties. To this end, poly(ethyleneimine)/DNA LBL coatings against microbial and inorganic fouling were developed, characterized and evaluated. DNA LBL coatings reduced inorganic fouling from tap water by 90% when incubated statically or under flow conditions mimicking surfaces in heat exchangers. The coatings also impaired biofilm formation by 93% on stainless steel from tap water, and resulted in a 97% lower adhesion force and reduced initial attachment of the human pathogens Staphylococcus aureus, Staphylococcus epidermidis and Pseudomonas aeruginosa on glass. This study demonstrates a proof of concept that LBL coatings with poly-anions harboring phosphate groups can address fouling in several applications.

Automated coating procedures to produce poly(ethylene glycol) brushes in fused-silica capillaries.

Many bioanalytical methods rely on electrophoretic separation of structurally labile and surface active biomolecules such as proteins and peptides. Often poor separation efficiency is due to surface adsorption processes leading to protein denaturation and surface fouling in the separation channel. Flexible and reliable approaches for preventing unwanted protein adsorption in separation science are thus in high demand. We therefore present new coating approaches based on an automated in-capillary surface-initiated atom transfer radical polymerization process (covalent coating) as well as by electrostatically adsorbing a presynthesized polymer leading to functionalized molecular brushes. The electroosmotic flow was measured following each step of the covalent coating procedure providing a detailed characterization and quality control. Both approaches resulted in good fouling resistance against the four model proteins cytochrome c, myoglobin, ovalbumin, and human serum albumin in the pH range 3.4-8.4. Further, even samples containing 10% v/v plasma derived from human blood did not show signs of adsorbing to the coated capillaries. The covalent as well as the electrostatically adsorbed coating were both found to be stable and provided almost complete suppression of the electroosmotic flow in the pH range 3.4-8.4. The coating procedures may easily be integrated in fully automated capillary electrophoresis methodologies.

On electrogenerated acid-facilitated electrografting of aryltriazenes to create well-defined aryl-tethered films.

The mechanism of electrogenerated acid-facilitated electrografting (EGAFE) of the aryltriazene, 4-(3,3-dimethyltriaz-1-enyl)benzyl-1-ferrocene carboxylate, was studied in detail using electrochemical quartz crystal microbalance (EQCM) and cyclic voltammetry. The measurements support the previously suggested mechanism that electrochemical oxidation of the EGA agent (i.e., N,N'-diphenylhydrazine) occurs on the forward oxidative sweep to generate protons, which in turn protonate the aryltriazene to form the corresponding aryldiazonium salt close to the electrode surface. On the reverse sweep, the electrochemical reduction of the aryldiazonium salt takes place, resulting in the electrografting of aryl groups. The EGAFE-generated film consists of a densely packed layer of ferrocenyl groups with nearly ideal electrochemical properties. The uncharged grafted film contains no solvent and electrolyte, but counterions and solvent can easily enter and be accommodated in the film upon charging. It is shown that all ferrocene moieties present in the multilayered film are electrochemically active, suggesting that the carbon skeleton possesses a sufficiently high flexibility to allow the occurrence of fast electron transfers between the randomly located redox stations. In comparison, EQCM measurements on aryldiazonium-grafted films reveal that they have a substantially smaller electrolyte uptake during charging and that they contain only 50% electroactive ferrocenyl groups relative to weight. Hence, half of these films consist of entrapped supporting electrolyte/solvent and/or simply electrochemically inactive material due to solvent inaccessibility.

Elucidation of the mechanism of redox grafting of diazotated anthraquinone.

Redox grafting of aryldiazonium salts containing redox units may be used to form exceptionally thick covalently attached conducting films, even in the micrometers range, in a controlled manner on glassy carbon and gold substrates. With the objective to investigate the mechanism of this process in detail, 1-anthraquinone (AQ) redox units were immobilized on these substrates by electroreduction of 9,10-dioxo-9,10-dihydroanthracene-1-diazonium tetrafluoroborate. Electrochemical quartz crystal microbalance was employed to follow the grafting process during a cyclic voltammetric sweep by recording the frequency change. The redox grafting is shown to have two mass gain regions/phases: an irreversible one due to the addition of AQ units to the substrate/film and a reversible one due to the association of cations from the supporting electrolyte with the AQ radical anions formed during the sweeping process. Scanning electrochemical microscopy was used to study the relationship between the conductivity of the film and the charging level of the AQ redox units in the grafted film. For that purpose, approach curves were recorded at a platinum ultramicroelectrode for AQ-containing films on gold and glassy carbon surfaces using the ferro/ferricyanide redox system as redox probe. It is concluded that the film growth has its origin in electron transfer processes occurring through the layer mediated by the redox moieties embedded in the organic film.

On surface-initiated atom transfer radical polymerization using diazonium chemistry to introduce the initiator layer.

This work features the controllability of surface-initiated atom transfer radical polymerization (SI-ATRP) of methyl methacrylate, initiated by a multilayered 2-bromoisobutyryl moiety formed via diazonium chemistry. The thickness as a function of polymerization time has been studied by varying different parameters such as the bromine content of the initiator layer, polarity of reaction medium, ligand type (L), and the ratio of activator (Cu(I)) to deactivator (Cu(II)) in order to ascertain the controllability of the SI-ATRP process. The variation of thickness versus surface concentration of bromine shows a gradual transition from mushroom to brush-type conformation of the surface anchored chains in both polar and nonpolar reaction medium. Interestingly, it is revealed that very thick polymer brushes, on the order of 1 µm, can be obtained at high bromine content of the initiator layer in toluene. The initial polymerization rate and the overall final thickness are higher in the case of nonpolar solvent (toluene) compared to polar medium (acetonitrile or N,N-dimethylformamide). The ligand affects the initial rate of polymerization, which correlates with the redox potentials of the pertinent Cu(II)/Cu(I) complexes (L = Me(6)TREN, PMDETA, and BIPY). It is also observed that the ability of polymer brushes to reinitiate depends on the initial thickness and the solvent used for generating it.

Nitrophenyl groups in diazonium-generated multilayered films: which are electrochemically responsive?

Various nitrophenyl-containing organic layers have been electrografted to glassy carbon surfaces using diazonium chemistry to elucidate the extent by which the layer structure influences the solvent (i.e., acetonitrile) accessibility, electroactivity, and chemical reactivity of the films. For most of these films, cyclic voltammetric and impedance spectroscopy measurements show that the electron-transfer process at the electrode is facile and independent of film thickness and structure. This is consistent with the occurrence of self-mediated electron transfers throughout the film with nitrophenyl groups serving as redox stations. Importantly, this behavior is seen only after the first potential sweep, the effect of which is to increase the porosity of the layer by inducing an irreversible desorption of nonchemisorbed material along with a reorganization of the film structure. From a kinetic point of view, the radical anions of surface-attached nitrophenyl groups are reactive toward the residual water present in acetonitrile. Thin layers (thickness of 1 to 2 nm) containing redox-active groups only in the outer part of the layer are protonated two to three times as fast as groups located in a more hydrophobic but still solvent-accessible inner layer. Hence, kinetic measurements can detect small differences in the layer environment. Finally, a deconvolution of the cyclic voltammetric response of an electrode grafted from 4-nitrobenzenediazonium discloses that roughly 25% of the overall signal can be attributed to the presence of 4-azonitrophenyl moieties introduced during the electrografting process.

General approach for monolayer formation of covalently attached aryl groups through electrografting of arylhydrazines.

An electrochemical approach is presented for carrying out controlled modification of carbon and metal surfaces with aryl groups through mild anodic oxidation of arylhydrazines. Electrochemical, PM-IRRAS, and ellipsometrical measurements reveal that monolayers are formed, the thickness of which is essentially independent of the substituent, pH, and grafting time and potential. This feature makes the approach very tolerant toward variations in the experimental conditions. Hence, this method should be considered as a strong option if the aim is to form thin, well-defined, and covalently assembled aryl layers on surfaces.

Soluble complexes in aqueous mixtures of low charge density comb polyelectrolyte and oppositely charged surfactant probed by scattering and NMR.

A low charge density polyelectrolyte with a high graft density of 45 units long poly(ethylene oxide) side-chains has been synthesized. In this comb polymer, denoted PEO(45)MEMA:METAC-2, 2 mol% of the repeating methacrylate units in the polymer backbone carry a permanent positive charge and the remaining 98 mol% a 45 unit long PEO side-chain. Here we describe the solution conformation of this polymer and its association with an anionic surfactant, sodium dodecylsulfate, SDS. It will be shown that the polymer can be viewed as a stiff rod with a cross-section radius of gyration of 29 A. The cross section of the rod contracts with increasing temperature due to decreased solvency of the PEO side-chains. The anionic surfactant associates to a significant degree with PEO(45)MEMA:METAC-2 to form soluble complexes at all stoichiometries. A cooperative association is observed as the free SDS concentration approaches 7 mM. At saturation the number of SDS molecules associated with the polymer amounts to 10 for each PEO side-chain. Two distinct populations of associated surfactants are observed, one is suggested to be molecularly distributed over the comb polymer and the other constitutes small micellar-like structures at the periphery of the aggregate. These conclusions are reached based on results from small-angle neutron scattering, static light scattering, NMR, and surface tension measurements.

Hydrophilic Polymer Brush Layers on Stainless Steel Using Multilayered ATRP Initiator Layer.

Thin polymer coatings (in tens of nanometers to a micron thick) are desired on industrial surfaces such as stainless steel. In this thickness range coatings are difficult to produce using conventional methods. In this context, surface-initiated controlled polymerization method can offer a promising tool to produce thin polymer coatings via bottom-up approach. Furthermore, the industrial surfaces are chemically heterogeneous and exhibit surface features in the form of grain boundaries and grain surfaces. Therefore, the thin coatings must be equally effective on both the grain surfaces and the grain boundary regions. This study illustrates a novel "periodic rejuvenation of surface initiation" process using surface-initiated ATRP technique to amplify the graft density of poly(oligoethylene glycol)methacrylate (POEGMA) brush layers on stainless steel 316L surface. The optimized conditions demonstrate a controlled, macroscopically homogeneous, and stable POEGMA brush layer covering both the grain surface and the grain boundary region. Various relevant parameters-surface cleaning methods, controllability of thickness, graft density, homogeneity and stability-were studied using techniques such as ellipsometer, X-ray photoelectron spectroscopy, scanning electron microscopy-energy-dispersive X-ray, surface zeta potential, and infrared reflection-adsorption spectroscopy.

Superhydrophilic polyelectrolyte brush layers with imparted anti-icing properties: effect of counter ions.

This work demonstrates the feasibility of superhydrophilic polyelectrolyte brush coatings for anti-icing applications. Five different types of ionic and nonionic polymer brush coatings of 25-100 nm thickness were formed on glass substrates using silane chemistry for surface premodification followed by polymerization via the SI-ATRP route. The cationic [2-(methacryloyloxy)ethyl]trimethylammonium chloride] and the anionic [poly(3-sulfopropyl methacrylate), poly(sodium methacrylate)] polyelectrolyte brushes were further exchanged with H+, Li+, Na+, K+, Ag+, Ca2+, La3+, C16N+, F-, Cl-, BF4-, SO4(2-), and C12SO3- ions. By consecutive measurements of the strength of ice adhesion toward ion-incorporated polymer brushes on glass it was found that Li+ ions reduce ice adhesion by 40% at -18 °C and 70% at -10 °C. Ag+ ions reduce ice adhesion by 80% at -10 °C relative to unmodified glass. In general, superhydrophilic polyelectrolyte brushes exhibit better anti-icing property at -10 °C compared to partially hydrophobic brushes such as poly(methyl methacrylate) and surfactant exchanged polyelectrolyte brushes. The data are interpreted using the concept of a quasi liquid layer (QLL) that is enhanced in the presence of highly hydrated ions at the interface. It is suggested that the ability of ions to coordinate water is directly related to the efficiency of a given anti-icing coating based on the polyelectrolyte brush concept.

Surface grafted glycopolymer brushes to enhance selective adhesion of HepG2 cells.

This work demonstrates the application of carbohydrate based methacrylate polymer brush, poly(2-lactobionamidoethyl methacrylate), for the purpose of cell adhesion studies. The first part of the work illustrates the effects of the structure of the aminosilane based ATRP initiator layer on the polymerization kinetics of 2-lactobionamidoethyl methacrylate) (LAMA) monomer on thermally oxidized silicon wafer. Both monolayer and multilayered aminosilane precursor layers have been prepared followed by reaction with 2-bromoisobutyrylbromide to form the ATRP initiator layer. It is inferred from the kinetic studies that the rate of termination is low on a multilayered initiator layer compared to a disordered monolayer structure. However both initiator types results in similar graft densities. Furthermore, it is shown that thick comb-like poly(LAMA) brushes can be constructed by initiating a second ATRP process on a previously formed poly(LAMA) brushes. The morphology of human hepatocellular carcinoma cancer cells (HepG2) on the comb-like poly(LAMA) brush layer has been studied. The fluorescent images of the HepG2 cells on the glycopolymer brush surface display distinct protrusions that extend outside of the cell periphery. On the other hand the cells on bare glass substrate display spheroid morphology. Further analysis using ToF-SIMS imaging shows that the HepG2 cells on glycopolymer surfaces is enriched with protein fragment along the cell periphery which is absent in the case of cells on bare glass substrate. It is suggested that the interaction of the galactose units of the polymer brush with the asialoglycoprotein receptor (ASGPR) of HepG2 cells has resulted in the protein enrichment along the cell periphery.

Attractive double-layer forces and charge regulation upon interaction between electrografted amine layers and silica.

Amine functionalities have been introduced on glassy carbon surfaces through electrografting of 4-(2-aminoethyl)benzenediazonium tetrafluoroborate. The grafted layers were characterized by ellipsometry and by nanomechanical mapping in air and aqueous solutions using the atomic force microscopy PeakForce QNM mode. The layer was found to be 2.5 nm thick with low roughness, comparable to that of the glassy carbon substrate. However, small semi-spherical features were observed in the topographical image, indicating a clustering of the grafted amine compound. The nanomechanical mapping also demonstrated some swelling of the layer in water and pointed toward an important contribution of electrostatic interactions for the tip-surface adhesion. The forces between an aminated glassy carbon surface and a µm-sized silica particle in aqueous solutions were measured at different ionic strength and pH-values. The results demonstrate that an attractive double-layer force predominates at large separations, and that the surface charge densities increase as the separation between the surfaces decreases. The degree of charge regulation on the aminated glassy carbon is significant. The relatively low surface charge density of the aminated glassy carbon is attributed to significant incorporation of counterions in the water-rich grafted layer.

Effect of polymer architecture on the adsorption properties of a nonionic polymer.

The adsorption of a linear- and bottle-brush poly(ethylene oxide (PEO))-based polymer, having comparable molecular weights, was studied by means of quartz crystal microbalance with dissipation monitoring ability (QCM-D) and AFM colloidal probe force measurements. The energy dissipation change monitored by QCM-D and the range of the steric forces obtained from force measurements demonstrated that linear PEO forms a more extended adsorption layer than the bottle-brush polymer, despite that the adsorbed mass is higher for the latter. Competitive adsorption studies revealed that linear PEO is readily displaced from the interface by the bottle-brush polymer. This was attributed to the higher surface affinity of the latter, which is governed by the number of contact points between the polymers and the interface, and the smaller loss of conformational entropy.

Adsorption characteristics of bottle-brush polymers on silica: effect of side chain and charge density.

The adsorption behavior of bottle-brush polymers with different charge/PEO ratio on silica was studied using optical reflectometry and QCM-D. The results obtained under different solution conditions clearly demonstrate the existence of two distinct adsorption mechanisms depending on the ratio of charge/PEO. In the case of low-charge density brush polymers (0-10 mol %), the adsorption occurs predominantly through the PEO side chains. However, the presence of a small amount of charge along the backbone (as low as 2 mol %) increases the adsorption significantly above that of the uncharged bottle-brush polymer in pure water. As the charge density of the brush polymers is increased to 25 mol % or larger the adsorption occurs predominantly through electrostatic interactions. The adsorbed layer structure was studied by measuring the layer dissipation using QCM-D. The adsorbed layer formed by the uncharged brush polymer dissipates only a small amount of energy that indicates that the brush lie along the surface, the scenario in which the maximum number of PEO side chains interact with the surface. The adsorbed layers formed by the low-charge density brush polymers (2-10 mol %) in water are more extended, which results in large energy dissipation, whereas those formed by the high-charge density brush polymers (50-100 mol %) have their backbone relatively flat on the surface and the energy dissipation is again low.

Surface properties of bottle-brush polyelectrolytes on mica: effects of side chain and charge densities.

Surface properties of a series of cationic bottle-brush polyelectrolytes with 45-unit-long poly(ethylene oxide) side chains were investigated by phase modulated ellipsometry and surface force measurements. The evaluation of the adsorbed mass of polymer on mica by means of ellipsometry is complex due to the transparency of mica and its birefringence and low dielectric constant. We therefore employed a new method to overcome these difficulties. The charge and the poly(ethylene oxide) side chain density of the bottle-brush polymers were varied from zero charge density and one side chain per segment to one charge per segment and no side chains, thus spanning the realm from a neutral bottle-brush polymer, via a partly charged brush polyelectrolyte, to a linear fully charged polyelectrolyte. The adsorption properties depend crucially on the polymer architecture. A minimum charge density of the polymer is required to facilitate adsorption to the oppositely charged surface. The maximum adsorbed amount and the maximum side chain density at the surface are obtained for the polymer with 50% charged segments and the remaining 50% of the segments carrying poly(ethylene oxide) side chains. It is found that brushlike layers are formed when 25-50% of the segments carry poly(ethylene oxide) side chains. In this paper, we argue that the repulsion between the side chains results in an adsorbed layer that is non-homogeneous on the molecular level. As a result, not all side chains will contribute equally to the steric repulsion but some will be stretched along the surface rather than perpendicular to it. By comparison with linear polyelectrolytes, it will be shown that the presence of the side chains counteracts adsorption. This is due to the entropic penalty of confining the side chains to the surface region.