RESUMO
We deposit Pt particles electrochemically on an electrode covered with a Nafion membrane. Platinum ions travel through the hydrophilic channels of the membrane, and platinum deposits are formed at the place where the channels make contact with the planar electrode. This procedure deposits the catalyst only at the end of the hydrophilic channels that cross the membrane; no catalyst is placed under the hydrophobic domains, where it would not be in contact with the electrolyte. By performing a series of cyclic voltammograms with this system, we show that deposition of the platinum through the membrane achieves better platinum utilization than deposition of platinum on the naked electrode followed by the placement of the membrane on top.
RESUMO
Several compositions of Pt-WO3 catalysts were synthesized and characterized for the electro-oxidation of methanol and CO. The surface morphologies of the catalysts were found to be dependent on the composition. X-ray energy dispersive spectroscopy and X-ray photoelectron spectroscopy results suggest a surface enrichment of WO3 in the codeposited Pt-WO3 catalysts. Cyclic voltammetry and chronoamperometry in methanol show an improvement in catalytic activity for the Pt-WO3 catalysts. A significant improvement in the poison tolerance toward CO and other organic intermediates was observed in the mixed metal-metal oxide catalyst. The catalytic performance of the different compositions was directly compared by normalization of the current to active sites. CO-stripping voltammetry suggests the involvement of WO3 in the catalytic process as opposed to a mere physical effect as suggested by previous work. A possible mechanism for this improvement is proposed based on the electrochemical data.
RESUMO
One key component in the assembly of nanoparticles is their precise positioning to enable the creation of new complex nano-objects. Controlling the nanoscale interactions is crucial for the prediction and understanding of the behaviour of nanoparticles (NPs) during their assembly. In the present work, we have manipulated bare and functionalized gold nanoparticles on flat and patterned silicon and silicon coated substrates with dynamic atomic force microscopy (AFM). Under ambient conditions, the particles adhere to silicon until a critical drive amplitude is reached by oscillations of the probing tip. Beyond that threshold, the particles start to follow different directions, depending on their geometry, size and adhesion to the substrate. Higher and respectively, lower mobility was observed when the gold particles were coated with methyl (-CH(3)) and hydroxyl (-OH) terminated thiol groups. This major result suggests that the adhesion of the particles to the substrate is strongly reduced by the presence of hydrophobic interfaces. The influence of critical parameters on the manipulation was investigated and discussed viz. the shape, size and grafting of the NPs, as well as the surface chemistry and the patterning of the substrate, and finally the operating conditions (temperature, humidity and scan velocity). Whereas the operating conditions and substrate structure are shown to have a strong effect on the mobility of the particles, we did not find any differences when manipulating ordered vs random distributed particles.
RESUMO
The influence of a surface potential gradient on the location and extent of electrochemical reactions was examined using a scanning electrochemical microscope. A linear potential gradient was imposed on the surface of a platinum-coated indium tin oxide electrode by applying two different potential values at the edges of the electrode. The applied potentials were used to control the location and extent of several electrochemical reactions, including the oxidation of Ru(NH3)6(2+), the oxidation of H2, and the oxidation of H2 in the presence of adsorbed CO. Scanning electrochemical mapping of these reactions was achieved by probing the feedback current associated with the oxidation products. The oxidation of Ru(NH3)6(2+) occurred at locations where the applied potential was positive of the formal potential of the Ru(NH3)6(2+/3+) redox couple. The position of this reaction on the surface could be spatially translated by manipulating the terminal potentials. The rate of hydrogen oxidation on the platinum-coated electrode varied spatially in the presence of a potential gradient and correlated with the nature of the electrode surface. High oxidation rates occurred at low potentials, with decreasing rates observed as the potential increased to values where platinum oxides formed. The extent of oxide formation versus position was confirmed with in-situ ellipsometry mapping. In the presence of adsorbed carbon monoxide, a potential gradient created a localized region of high activity for hydrogen oxidation at potentials between where carbon monoxide was adsorbed and platinum oxides formed. The position of this localized region of activity could be readily translated along the surface by changing the terminal potential values. The ability to manipulate electrochemical reactions spatially on a surface has potential application in microscale analytical devices as well as in the discovery and analysis of electrocatalytic systems.