Tree-Inspired Aerogel Comprising Nonoxidized Graphene Flakes and Cellulose as Solar Absorber for Efficient Water Generation.

As global freshwater shortages worsen, solar steam generation (SSG) emerges as a promising, eco-friendly, and cost-effective solution for water purification. However, widespread SSG implementation requires efficient photothermal materials and solar evaporators that integrate enhanced light-to-heat conversion, rapid water transportation, and optimal thermal management. This study investigates using nonoxidized graphene flakes (NOGF) with negligible defects as photothermal materials capable of absorbing over 98% of sunlight. By combining NOGF with cellulose nanofibers (CNF) through bidirectional freeze casting, we created a vertically and radially aligned solar evaporator. The hybrid aerogel exhibited exceptional solar absorption, efficient solar-to-thermal conversion, and improved surface wettability. Inspired by tree structures, our design ensures rapid water supply while minimizing heat loss. With low NOGF content (∼10.0%), the NOGF/CNF aerogel achieves a solar steam generation rate of 2.39 kg m-2 h-1 with an energy conversion efficiency of 93.7% under 1-sun illumination, promising applications in seawater desalination and wastewater purification.

Metal Nanocomposites Reinforced by Ceramic Nanoarchitecture: Exploiting Extrinsic Size Effects for High Mechanical Strength.

The pursuit of harnessing superior mechanical properties achieved through the size effect on a macroscopic scale has been a prominent focus in engineering, as size-induced strengthening is enabled only in the nanoscale regime. This study presents a metal/ceramic/metal (MCM) nanocomposite reinforced by ceramic nanoarchitectures. Through proximity-field nanopatterning, the inch-scale production of nanoarchitecture films is enabled in a single fabrication step. The developed three-dimensional (3D) Ni/Al2O3/Ni nanocomposite film exhibits significantly high compressive strength, corresponding to an increase of approximately 30% compared with that calculated using the upper limits of the conventional rule of mixtures. The exceptional strength of the 3D MCM nanocomposite can be attributed to the extrinsic size effect of the ceramic nanoarchitectures. By combining size-induced strengthening of ceramics with the strengthening law for composites, a new type of strengthening model is derived and experimentally validated using the 3D MCM nanocomposite.

All-Graphene Quantum Dot-Derived Battery: Regulating Redox Activity Through Localized Subdomains.

In the quest for materials sustainability for grid-scale applications, graphene quantum dot (GQD), prepared via eco-efficient processes, is one of the promising graphitic-organic matters that have the potential to provide greener solutions for replacing metal-based battery electrodes. However, the utilization of GQDs as electroactive materials has been limited; their redox behaviors associated with the electronic bandgap property from the sp2 carbon subdomains, surrounded by functional groups, are yet to be understood. Here, the experimental realization of a subdomained GQD-based anode with stable cyclability over 1000 cycles, combined with theoretical calculations, enables a better understanding of the decisive impact of controlled redox site distributions on battery performance. The GQDs are further employed in cathode as a platform for full utilization of inherent electrochemical activity of bio-inspired redox-active organic motifs, phenoxazine. Using the GQD-derived anode and cathode, an all-GQD battery achieves a high energy density of 290 Wh kgcathode -1 (160 Wh kgcathode+anode -1 ), demonstrating an effective way to improve reaction reversibility and energy density of sustainable, metal-free batteries.

Hierarchically porous Au nanostructures with interconnected channels for efficient mass transport in electrocatalytic CO2 reduction.

Electrocatalytic CO2 reduction is a promising way to provide renewable energy from gaseous CO2 The development of nanostructures improves energy efficiency and selectivity for value-added chemicals, but complex nanostructures limit the CO2 conversion rates due to poor mass transport during vigorous electrolysis. Herein, we propose a three-dimensional (3D) hierarchically porous Au comprising interconnected macroporous channels (200-300 nm) and nanopores (∼10 nm) fabricated via proximity-field nanopatterning. The interconnected macropores and nanopores enable efficient mass transport and large active areas, respectively. The roles of each pore network are investigated using reliable 3D nanostructures possessing controlled pore distribution and size. The hierarchical nanostructured electrodes show a high CO selectivity of 85.8% at a low overpotential of 0.264 V and efficient mass activity that is maximum 3.96 times higher than that of dealloyed nanoporous Au. Hence, the systematic model study shows the proposed hierarchical nanostructures have important value in increasing the efficiency of expensive Au.

Improved Crystallinity of Graphene Grown on Cu/Ni (111) through Sequential Mobile Hot-Wire Heat Treatment.

Over the past few years, many efforts have been devoted to growing single-crystal graphene due to its great potential in future applications. However, a number of issues remain for single-crystal graphene growth, such as control of nanoscale defects and the substrate-dependent nonuniformity of graphene quality. In this work, we demonstrate a possible route toward single-crystal graphene by combining aligned nucleation of graphene nanograins on Cu/Ni (111) and sequential heat treatment over pregrown graphene grains. By use of a mobile hot-wire CVD system, prealigned grains were stitched into one continuous film with up to ∼97% single-crystal domains, compared to graphene grown on polycrystalline Cu, which was predominantly high-angle tilt boundary (HATB) domains. The single-crystal-like graphene showed remarkably high thermal conductivity and carrier mobility of ∼1349 W/mK at 350 K and ∼33 600 (38 400) cm2 V-1 s-1 for electrons (holes), respectively, which indicates that the crystallinity is high due to suppression of HATB domains.

Two-Dimensional WO3 Nanosheets Chemically Converted from Layered WS2 for High-Performance Electrochromic Devices.

Two-dimensional (2D) transitional metal oxides (TMOs) are an attractive class of materials due to the combined advantages of high active surface area, enhanced electrochemical properties, and stability. Among the 2D TMOs, 2D tungsten oxide (WO3) nanosheets possess great potential in electrochemical applications, particularly in electrochromic (EC) devices. However, feasible production of 2D WO3 nanosheets is challenging due to the innate 3D crystallographic structure of WO3. Here we report a novel solution-phase synthesis of 2D WO3 nanosheets through simple oxidation from 2D tungsten disulfide (WS2) nanosheets exfoliated from bulk WS2 powder. The complete conversion from WS2 into WO3 was confirmed through crystallographic and elemental analyses, followed by validation of the 2D WO3 nanosheets applied in the EC device. The EC device showed color modulation of 62.57% at 700 nm wavelength, which is 3.43 times higher than the value of the conventional device using bulk WO3 powder, while also showing enhancement of ∼46.62% and ∼62.71% in switching response-time (coloration and bleaching). The mechanism of enhancement was rationalized through comparative analysis based on the thickness of the WO3 components. In the future, 2D WO3 nanosheets could also be used for other promising applications such as sensors, catalysis, thermoelectric, and energy conversion.

Emergence of New Density-Strength Scaling Law in 3D Hollow Ceramic Nanoarchitectures.

Density-strength tradeoff appears to be an inherent limitation for most materials and therefore design of cell topology that mitigates strength decrease with density reduction has been a long-lasting engineering pursue for porous materials. Continuum-mechanics-based analyses of mechanical responses of conventional porous materials with bending-dominated structures often give the density-strength scaling law following the power-law relationship with an exponent of 1.5 or higher, which consequentially determines the upper bound of the specific strength for a material to reach. In this work, a new design criterion capable of significantly abating strength degradation in lightweight materials is presented, by successfully combining the size-induced strengthening effect in nanomaterials with the architectural design of cellular porous materials. Hollow-tube-based 3D ceramic nanoarchitectures satisfying such criterion are fabricated in large area using proximity field nano-patterning and atomic layer deposition. Experimental data from micropillar compression confirm that the strengths of these nanoarchitectural materials scale with relative densities with a power-law exponent of 0.93, a hardly observable value in conventional bending-dominated porous materials. This discovery of a new density-strength scaling law in nanoarchitectured materials will contribute to creating new lightweight structural materials attaining unprecedented specific strengths overcoming the conventional limit.

Fast P3HT Exciton Dissociation and Absorption Enhancement of Organic Solar Cells by PEG-Functionalized Graphene Quantum Dots.

PEG-functionalized graphene quantum dots (GQDs) are shown to promote fast exciton dissociation in organic solar cells. Short-chain PEG promotes the most favorable interaction with other organic layers, and the overall efficiency is improved by 36% when compared to the reference devices. The mechanism of enhancement is shown to be increased absorption due to fewer charges remain-ing in the bound state.

Scalable exfoliation process for highly soluble boron nitride nanoplatelets by hydroxide-assisted ball milling.

The scalable preparation of two-dimensional hexagonal boron nitride (h-BN) is essential for practical applications. Despite intense research in this area, high-yield production of two-dimensional h-BN with large-size and high solubility remains a key challenge. In the present work, we propose a scalable exfoliation process for hydroxyl-functionalized BN nanoplatelets (OH-BNNPs) by a simple ball milling of BN powders in the presence of sodium hydroxide via the synergetic effect of chemical peeling and mechanical shear forces. The hydroxide-assisted ball milling process results in relatively large flakes with an average size of 1.5 µm with little damage to the in-plane structure of the OH-BNNP and high yields of 18%. The resultant OH-BNNP samples can be redispersed in various solvents and form stable dispersions that can be used for multiple purposes. The incorporation of the BNNPs into the polyethylene matrix effectively enhanced the barrier properties of the polyethylene due to increased tortuosity of the diffusion path of the gas molecules. Hydroxide-assisted ball milling process can thus provide simple and efficient approaches to scalable preparation of large-size and highly soluble BNNPs. Moreover, this exfoliation process is not only easily scalable but also applicable to other layered materials.

Moisture Barrier Composites Made of Non-Oxidized Graphene Flakes.

Graphene flakes (GFs) with minimized defects and oxidation ratios are incorporated into polyethylene (PE) to enhance the moisture barrier. GFs produced involving solvothermal intercalation show extremely low oxidation rates (3.17%), and are noncovalently functionalized in situ, inducing strong hydrophobicity. The fabricated composite possesses the best moisture barrier performance reported for a polymer-graphene composite.

Amplification of hot electron flow by the surface plasmon effect on metal-insulator-metal nanodiodes.

Au-TiO2-Ti nanodiodes with a metal-insulator-metal structure were used to probe hot electron flows generated upon photon absorption. Hot electrons, generated when light is absorbed in the Au electrode of the nanodiode, can travel across the TiO2, leading to a photocurrent. Here, we demonstrate amplification of the hot electron flow by (1) localized surface plasmon resonance on plasmonic nanostructures fabricated by annealing the Au-TiO2-Ti nanodiodes, and (2) reducing the thickness of the TiO2. We show a correlation between changes in the morphology of the Au electrodes caused by annealing and amplification of the photocurrent. Based on the exponential dependence of the photocurrent on TiO2 thickness, the transport mechanism for the hot electrons across the nanodiodes is proposed.

High-angle tilt boundary graphene domain recrystallized from mobile hot-wire-assisted chemical vapor deposition system.

Crystallization of materials has attracted research interest for a long time, and its mechanisms in three-dimensional materials have been well studied. However, crystallization of two-dimensional (2D) materials is yet to be challenged. Clarifying the dynamics underlying growth of 2D materials will provide the insight for the potential route to synthesize large and highly crystallized 2D domains with low defects. Here, we present the growth dynamics and recrystallization of 2D material graphene under a mobile hot-wire assisted chemical vapor deposition (MHW-CVD) system. Under local but sequential heating by MHW-CVD system, the initial nucleation of nanocrystalline graphenes, which was not extended into the growth stage due to the insufficient thermal energy, took a recrystallization and converted into a grand single crystal domain. During this process, the stitching-like healing of graphene was also observed. The local but sequential endowing thermal energy to nanocrystalline graphenes enabled us to simultaneously reveal the recrystallization and healing dynamics in graphene growth, which suggests an alternative route to synthesize a highly crystalline and large domain size graphene. Also, this recrystallization and healing of 2D nanocrystalline graphenes offers an interesting insight on the growth mechanism of 2D materials.

Identification of metalloporphyrins with high sensitivity using graphene-enhanced resonance Raman scattering.

Graphene-enhanced resonance Raman scattering (GERRS) was performed for the detection of three different metallo-octaethylporphyrins (M-OEPs; M = 2H, FeCl, and Pt) homogeneously thermal vapor deposited on a graphene surface. GERRS of M-OEPs were measured using three different excitation wavelengths, λ(ex) = 405, 532, and 633 nm, and characterized detail vibrational bands for the identification of M-OEPs. The GERRS spectra of Pt-OEP at λ(ex) = 532 nm showed ~29 and ~162 times signal enhancement ratio on graphene and on graphene with Ag nanoclusters, respectively, compared to the spectra from bare SiO2 substrate. This enhancement ratio, however, was varied with M-OEPs and excitation wavelengths. The characteristic peaks and band shapes of GERRS for each M-OEP were measured with high sensitivity (100 pmol of thermal vapor deposited Pt-OEP), and these facilitate the selectively recognition of molecules. Also, the peaks shift and broadening provide the evidence of the interaction between graphene and M-OEPs through the charge transfer and π-orbital interaction. The increase of graphene layer induced the decrease of signal intensity and GERRS effect was almost not observed on the thick graphite flakes. Further experiments with various substrates demonstrated that the interaction of single layer of graphene with molecule is the origin of the Raman signal enhancement of M-OEPs. In this experiment, we proved the graphene is a good alternative substrate of Raman spectroscopy for the selective detection of various metalloporphyrins with high sensitivity.

Ion-exchange mechanism of layered transition-metal oxides: case study of LiNi(0.5)Mn(0.5)O2.

An ion-exchange process can be an effective route to synthesize new quasi-equilibrium phases with a desired crystal structure. Important layered-type battery materials, such as LiMnO2 and LiNi(0.5)Mn(0.5)O2, can be obtained through this method from a sodium-containing parent structure, and they often show electrochemical properties remarkably distinct from those of their solid-state synthesized equivalents. However, while ion exchange is generally believed to occur via a simple topotactic reaction, the detailed phase transformation mechanism during the process is not yet fully understood. For the case of layered LiNi(0.5)Mn(0.5)O2, we show through ex situ X-ray diffraction (XRD) that the ion-exchange process consists of several sequential phase transformations. By a study of the intermediate phase, it is shown that the residual sodium ions in the final structure may greatly affect the electrochemical (de)lithiation mechanism.

Bifunctional composite catalysts using Co3O4 nanofibers immobilized on nonoxidized graphene nanoflakes for high-capacity and long-cycle Li-O2 batteries.

Designing a highly efficient catalyst is essential to improve the electrochemical performance of Li-O2 batteries for long-term cycling. Furthermore, these batteries often show significant capacity fading due to the irreversible reaction characteristics of the Li2O2 product. To overcome these limitations, we propose a bifunctional composite catalyst composed of electrospun one-dimensional (1D) Co3O4 nanofibers (NFs) immobilized on both sides of the 2D nonoxidized graphene nanoflakes (GNFs) for an oxygen electrode in Li-O2 batteries. Highly conductive GNFs with noncovalent functionalization can facilitate a homogeneous dispersion in solution, thereby enabling simple and uniform attachment of 1D Co3O4 NFs on GNFs without restacking. High first discharge capacity of 10 500 mAh/g and superior cyclability for 80 cycles with a limited capacity of 1000 mAh/g were achieved by (i) improved catalytic activity of 1D Co3O4 NFs with large surface area, (ii) facile electron transport via interconnected GNFs functionalized by Co3O4 NFs, and (iii) fast O2 diffusion through the ultrathin GNF layer and porous Co3O4 NF networks.

Wearable textile battery rechargeable by solar energy.

Wearable electronics represent a significant paradigm shift in consumer electronics since they eliminate the necessity for separate carriage of devices. In particular, integration of flexible electronic devices with clothes, glasses, watches, and skin will bring new opportunities beyond what can be imagined by current inflexible counterparts. Although considerable progresses have been seen for wearable electronics, lithium rechargeable batteries, the power sources of the devices, do not keep pace with such progresses due to tenuous mechanical stabilities, causing them to remain as the limiting elements in the entire technology. Herein, we revisit the key components of the battery (current collector, binder, and separator) and replace them with the materials that support robust mechanical endurance of the battery. The final full-cells in the forms of clothes and watchstraps exhibited comparable electrochemical performance to those of conventional metal foil-based cells even under severe folding-unfolding motions simulating actual wearing conditions. Furthermore, the wearable textile battery was integrated with flexible and lightweight solar cells on the battery pouch to enable convenient solar-charging capabilities.

High-Color-Rendition White QLEDs by Balancing Red, Green and Blue Centres in Eco-Friendly ZnCuGaS:In@ZnS Quantum Dots.

White light-emitting diodes (WLEDs) are the key components in the next-generation lighting and display devices. The inherent toxicity of Cd/Pb-based quantum dots (QDs) limits the further application in WLEDs. Recently, more attention is focused on eco-friendly QDs and their WLEDs, especially the phosphor-free WLEDs based on mono-component, which profits from bias-insensitive color stability. However, the imbalanced carrier distribution between red-green-blue luminescent centers, even the absence of a certain luminescent center, hinders their balanced and stable photoluminescence/electroluminescence (PL/EL). Here, an In3+-doped strategy in Zn-Cu-Ga-S@ZnS QDs is first proposed, and the balanced carrier distribution is realized by non-equivalent substitution and In3+ doping concentration modulation. The alleviation of the green emitter by the In3+-related red emitter and the compensation of blue emitter by the Zn-related electronic states contribute to the balanced red-green-blue emitting with high PL quantum yield (PLQY) of 95.3% and long lifetime (T90) of over 1100 h in atmospheric conditions. Thus, the In3+-doped WLEDs can achieve exceedingly slight proportional variations between red-green-blue EL intensity over time (∆CIE = (0.007, 0.009)), and high champion CRI of 94.9. This study proposes a single-component QD with balanced and stable red-green-blue PL/EL spectrum, meeting the requirements of lighting and display.

High figure-of-merit for ZnO nanostructures by interfacing lowly-oxidized graphene quantum dots.

Thermoelectric technology has potential for converting waste heat into electricity. Although traditional thermoelectric materials exhibit extremely high thermoelectric performances, their scarcity and toxicity limit their applications. Zinc oxide (ZnO) emerges as a promising alternative owing to its high thermal stability and relatively high Seebeck coefficient, while also being earth-abundant and nontoxic. However, its high thermal conductivity (>40 W m-1K-1) remains a challenge. In this study, we use a multi-step strategy to achieve a significantly high dimensionless figure-of-merit (zT) value of approximately 0.486 at 580 K (estimated value) by interfacing graphene quantum dots with 3D nanostructured ZnO. Here, we show the fabrication of graphene quantum dots interfaced 3D ZnO, yielding the highest zT value ever reported for ZnO counterparts; specifically, our experimental results indicate that the fabricated 3D GQD@ZnO exhibited a significantly low thermal conductivity of 0.785 W m-1K-1 (estimated value) and a remarkably high Seebeck coefficient of - 556 µV K-1 at 580 K.

Compression-sensitive smart windows: inclined pores for dynamic transparency changes.

Smart windows, capable of tailoring light transmission, can significantly reduce energy consumption in building services. While mechano-responsive windows activated by strains are promising candidates, they face long-lasting challenges in which the space for the light scatterer's operation has to be enlarged along with the window size, undermining the practicality. Recent attempts to tackle this challenge inevitably generate side effects with compromised performance in light modulation. Here, we introduce a cuttlefish-inspired design to enable the closing and opening of pores within the 3D porous structure by through-thickness compression, offering opacity and transparency upon release and compression. By changing the activation mode from the conventional in-plane to through-thickness direction, the space requirement is intrinsically decoupled from the lateral size of the scatterer. Central to our design is the asymmetry of pore orientation in the 3D porous structure. These inclined pores against the normal direction increase the opaqueness upon release and improve light modulation sensitivity to compression, enabling transmittance regulation upon compression by an infinitesimal displacement of 50 µm. This work establishes a milestone for smart window technologies and will drive advancements in the development of opto-electric devices.

Enhanced mechanical properties of epoxy nanocomposites by mixing noncovalently functionalized boron nitride nanoflakes.

The influence of surface modifications on the mechanical properties of epoxy-hexagonal boron nitride nanoflake (BNNF) nanocomposites is investigated. Homogeneous distributions of boron nitride nanoflakes in a polymer matrix, preserving intrinsic material properties of boron nitride nanoflakes, is the key to successful composite applications. Here, a method is suggested to obtain noncovalently functionalized BNNFs with 1-pyrenebutyric acid (PBA) molecules and to synthesize epoxy-BNNF nanocomposites with enhanced mechanical properties. The incorporation of noncovalently functionalized BNNFs into epoxy resin yields an elastic modulus of 3.34 GPa, and 71.9 MPa ultimate tensile strength at 0.3 wt%. The toughening enhancement is as high as 107% compared to the value of neat epoxy. The creep strain and the creep compliance of the noncovalently functionalized BNNF nanocomposite is significantly less than the neat epoxy and the nonfunctionalized BNNF nanocomposite. Noncovalent functionalization of BNNFs is effective to increase mechanical properties by strong affinity between the fillers and the matrix.