Stress and Exposure Time on von Willebrand Factor Degradation.

Despite the prevailing use of the continuous flow left ventricular assist devices (cf-LVAD), acquired von Willebrand syndrome (AvWS) associated with cf-LVAD still remains a major complication. As AvWS is known to be dependent on shear stress (τ) and exposure time (texp ), this study examined the degradation of high molecular weight multimers (HMWM) of von Willebrand factor (vWF) in terms of τ and texp . Two custom apparatus, i.e., capillary-tubing-type degrader (CTD) and Taylor-Couette-type degrader (TCD) were developed for short-term (0.033 sec ≤ texp  ≤ 1.05 s) and long-term (10 s ≤ texp  ≤ 10 min) shear exposures of vWF, respectively. Flow conditions indexed by Reynolds number (Re) for CTD were 14 ≤ Re ≤ 288 with corresponding laminar stress level of 52 ≤  τ CTD  ≤ 1042 dyne/cm2 . Flow conditions for TCD were 100 ≤ Re ≤ 2500 with corresponding rotor speed of 180 ≤ o  ≤ 4000 RPM and laminar stress level of 50 ≤  τ TCD  ≤ 1114 dyne/cm2 . Due to transitional and turbulent flows in TCD at Re > 1117, total stress (i.e., τ total  = laminar + turbulent) was also calculated using a computational fluid dynamics (CFD) solver, Converge CFD (Converge Science Inc., Madison, WI, USA). Inhibition of ADAMTS13 with different concentration of EDTA (5 mM and 10 mM) was also performed to investigate the mechanism of cleavage in terms of mechanical and enzymatic aspects. Degradation of HMWM with CTD was negligible at all given testing conditions. Although no degradation of HMWM was observed with TCD at Re < 1117 ( τ total  = 1012 dyne/cm2 ), increase in degradation of HMWM was observed beyond Re of 1117 for all given exposure times. At Re ~ 2500 ( τ total  = 3070 dyne/cm2 ) with texp  = 60 s, a severe degradation of HMWM (90.7 ± 3.8%, abnormal) was observed, and almost complete degradation of HMWM (96.1 ± 1.9%, abnormal) was observed with texp  = 600 s. The inhibition studies with 5 mM EDTA at Re ~ 2500 showed that loss of HMWM was negligible (<10%, normal) for all given exposure times except for texp  = 10 min (39.5 ± 22.3%, borderline-abnormal). With 10 mM EDTA, no degradation of HMWM was observed (11.1 ± 4.4%, normal) even for texp  = 10 min. This study investigated the effect of shear stress and exposure time on the HMWM of vWF in laminar and turbulent flows. The inhibition study by EDTA confirms that degradation of HMWM is initiated by shear-induced unfolding followed by enzymatic cleavage at given conditions. Determination of magnitude of each mechanism needs further investigation. It is also important to note that the degradation of vWF is highly dependent on turbulence regardless of the time exposed within our testing conditions.

Acquired Von Willebrand Syndrome and Blood Pump Design.

The existence of acquired von Willebrand syndrome (AVWS) in patients with continuous flow left ventricular assist devices (LVADs) is well documented and has been verified by numerous investigators. AVWS has not been observed to occur in pulsatile devices such as the SynCardia total artificial heart (TAH), the HeartMate XVE, and the Thoratec pulsatile ventricular assist device (PVAD) used as a single pump. AVWS can also occur in patients with aortic stenosis, ventricular septal defect, mitral stenosis, and patent ductus arteriosus. It has been experimentally verified that supraphysiologic shear stress that occurs under these conditions can cleave the von Willebrand molecule, but the critical magnitude of stress and duration is unclear. Limited experimental results demonstrate that shear stresses as low as 5 Pa (50 dyne/cm2 ) can cause cleavage. Stresses in current centrifugal pumps can be as high as two orders of magnitude greater than this value. Pulsatile LVADs have stresses almost two orders of magnitude less than continuous flow LVADs. In order to improve continuous flow LVADs, the challenge for designers is to first determine the magnitude and duration of stress that is causing AVWS and then, if possible, design a pump below these stresses.

Ventricular contractility and compliance measured during axial flow blood pump support: in vitro study.

End-systolic elastance and end-diastolic compliance have been used to quantify systolic and diastolic function of the left ventricle (LV). In this study, the effective end-systolic elastance, (EES )eff , end-systolic volume intercept, (V0 )eff , and end-diastolic compliance of the LV were assessed at various levels of left ventricular assist device (LVAD) support. We tested the hypothesis that (EES )eff and (V0 )eff vary as a function of LVAD speed, while compliance does not change. The Penn State in vitro cardiac simulator was used in two heart conditions (control and heart failure [HF]) with the HeartMate II axial flow LVAD. The LVAD speed was linearly increased from 6000 to 11 000 rpm, with 500-rpm increments. The end-systolic and end-diastolic pressure-volume relationships were estimated at each LVAD speed. Acute LVAD support itself showed pseudo-improvement of ventricular contractility. The (EES )eff and (V0 )eff in HF were found to be dependent on the LVAD speed. The effective compliance for both control and HF was independent of the LVAD speed. Therefore, when examining the time-course cardiac recovery induced by the LVAD support, LV performance should be measured immediately before and after LVAD support while keeping LVAD speed consistent to avoid potential overestimation of long-term cardiac recovery.

Development of the PSU Child Pump.

The Pennsylvania State University (PSU) Child Pump, a centrifugal continuous-flow ventricular assist device (cf-VAD), is being developed as a suitable long-term implantable device for pediatric heart failure patients between 10 and 35 kg, body surface area (BSA) of 0.5-1.2 m2, 1-11 years of age, and requiring a mean cardiac output of 1.0-3.5 L/min. In-vitro hydraulic and hemodynamic performances were evaluated on a custom mock circulatory loop with ovine blood. Normalized index of hemolysis (NIH) was evaluated under four conditions: 1) 8,300 rpm, 3.5 L/min, ΔP = 60 mm Hg, 2) 8,150 rpm, 5.1 L/min, ΔP = 20 mm Hg, 3) 8,400 rpm, 3.2 L/min, ΔP = 70 mm Hg, and 4) 9,850 rpm, 5.0 L/min, ΔP = 80 mm Hg, resulting in normalized index of hemolysis = 0.027 ± 0.013, 0.015 ± 0.006, 0.016 ± 0.008, and 0.026 ± 0.011 mg/dl, respectively. A mock fit study was conducted using a three-dimensional printed model of a 19 kg patient's thoracic cavity to compare the size of the PSU Child Pump to the HeartMate3 and the HVAD. Results indicate the PSU Child Pump will be a safer, appropriately sized device capable of providing the given patient cohort proper support while minimizing the risks of blood trauma as they wait for a transplant.

Kinetic and Dynamic Effects on Degradation of von Willebrand Factor.

The loss of high molecular weight multimers (HMWM) of von Willebrand factor (vWF) in aortic stenosis (AS) and continuous-flow left ventricular assist devices (cf-LVADs) is believed to be associated with high turbulent blood shear. The objective of this study is to understand the degradation mechanism of HMWM in terms of exposure time (kinetic) and flow regime (dynamics) within clinically relevant pathophysiologic conditions. A custom high-shear rotary device capable of creating fully controlled exposure times and flows was used. The system was set so that human platelet-poor plasma flowed through at 1.75 ml/sec, 0.76 ml/sec, or 0.38 ml/sec resulting in the exposure time ( texp ) of 22, 50, or 100 ms, respectively. The flow was characterized by the Reynolds number (Re). The device was run under laminar (Re = 1,500), transitional (Re = 3,000; Re = 3,500), and turbulent (Re = 4,500) conditions at a given texp followed by multimer analysis. No degradation was observed at laminar flow at all given texp . Degradation of HMWM at a given texp increases with the Re. Re ( p < 0.0001) and texp ( p = 0.0034) are significant factors in the degradation of HMWM. Interaction between Re and texp , however, is not always significant ( p = 0.73).

In Vivo Evaluation of a Physiologic Control System for Rotary Blood Pumps Based on the Left Ventricular Pressure-Volume Loop.

Current generation continuous flow assist devices to operate at a fixed speed, which limits preload response and exercise capacity in left ventricular assist device (LVAD) patients. A feedback control system was developed to automatically adjust pump speed based on direct measurements of ventricular loading using a custom cannula tip with an integrated pressure sensor and volume-sensing conductance electrodes. The input to the control system is the integral of the left ventricular (LV) pressure versus conductance loop (PGA) over each cardiac cycle. The feedback control system adjusts pump speed based on the difference between the measured PGA and the desired PGA. The control system and cannula tip were tested in acute ovine studies (n = 5) using the HeartMate II LVAD. The preload response of the control system was evaluated by partially occluding and releasing the inferior vena cava using a vessel loop snare. The cannula tip was integrated onto a custom centrifugal flow LVAD and tested in a 14-day bovine study. The control system adjusted pump support to maintain constant ventricular loading: pump speed increased (decreased) following an increase (decrease) in preload. This study demonstrated in vivo the Starling-like response of an automatic pump control system based on direct measurements of LV loading.

Finite element modeling of the pulmonary autograft at systemic pressure before remodeling.

BACKGROUND AND AIM OF THE STUDY: Pulmonary autograft dilatation requiring reoperation is an Achilles' heel of the Ross procedure, as exposure to systemic pressure increases autograft wall stress, which may in turn lead to tissue remodeling and aneurysmal pathology. However, the magnitude of autograft wall stress with the Ross procedure is unknown. The study aim was to develop a realistic finite element (FE) model of the autograft, and to perform simulations at systemic pressure to determine wall stress distribution immediately after the Ross operation. METHODS: The porcine pulmonary root geometry was generated from high-resolution microcomputed tomography (microCT) images to create a mesh composed of hexahedral elements. Previously defined constitutive equations were used to describe the regional material properties of the native porcine pulmonary root. The anterior and posterior pulmonary arteries, and each of the pulmonary sinuses, were best described by non-linear, anisotropic Fung strain energy functions, and input individually into the model. Autograft dilatation and wall stress distribution during pulmonary and systemic loading prior to remodeling were determined using explicit FE analysis in LS-DYNA. RESULTS: The autograft was highly compliant in the low-strain region, and the majority of dilation occurred with < 30 mmHg of pressurization. During pulmonic loading, a typical inflation/deflation was observed between systole and diastole, but the autograft remained almost completely dilated throughout the cardiac cycle at systemic pressure. Although the systolic blood pressure was 380% greater in the aortic than in the pulmonary position, the peak systolic diameter was increased by only 28%. The maximum principal wall stress increased approximately 10-fold during systole and 25-fold during diastole, and was greater in the sinus than the distal artery for all simulations. CONCLUSION: Under systemic loading conditions, the pulmonary autograft remained fully dilated and experienced large wall stresses concentrated in the sinus. The future correlation of this model with explanted autografts may lead to an improved understanding of tissue remodeling following the Ross procedure.

Dynamics of Blood Flows in Aortic Stenosis: Mild, Moderate, and Severe.

Supraphysiologic high shear stresses created in calcific aortic stenosis (AS) are known to cause hemostatic abnormalities, however, the relationship between the complex blood flows over the severity of AS and hemostatic abnormalities still remains unclear. This study systematically characterized the blood flow in mild, moderate, and severe AS. A series of large eddy simulations (LES) validated by particle image velocimetry were performed on physiologically representative AS models with a peak physiologic flow condition of 18 liter per minute. Time-accurate velocity fields, transvalvular pressure gradient, and laminar viscous-and turbulent (or Reynolds) shear stresses (RSSmax) were evaluated for each degree of severity. The peak velocities of mild, moderate, and severe AS were on the order of 2.0, 4.0, and 8.0 m/s, respectively. Jet velocity in severe AS was highly skewed with extremely high velocity (as high as 8 m/s) and mainly traveled through the posterior aortic wall up to the aortic arch while still carrying a relatively high velocity, that is, >4 m/s. The mean laminar viscous wall shear stresses (WSS) for mild, moderate, and severe AS were on the order of 40, 100, and 180 Pa, respectively. The RSSmax were on the order of 260, 490, and 2,500 Pa for mild, moderate, and severe AS, respectively. This study may provide a link between altered flows in AS and hemostatic abnormalities such as acquired von Willebrand syndrome and hemolysis, thus, help diagnosing and timing of the treatment.

Miniaturized Fontan Circulation Assist Device: Chronic In Vivo Evaluation.

We have miniaturized and optimized our implantable rotary blood pump developed to provide long-term mechanical right heart support for patients who have failing Fontan circulation. The objective of this study was to evaluate the miniaturized Fontan circulation assist device (mini-FCAD) during 30-day sheep studies (n = 5). A complete right heart bypass was performed and all return flow was supported by the pump. Postoperatively, unfractionated heparin was given to maintain thromboelastography R times of 2× normal. The first two studies were terminated on day 0 and day 4 due to complications. In the final three studies, the animals remained healthy and were electively terminated at 30 ± 2 days. Pump flow was between 5 and 7 lpm, left atrial pressure remained normal, and inlet pressures were between 3 and 18 mm Hg with no incidents of suction. There was no evidence of hemolysis, end organ or pulmonary dysfunction, thromboembolic events, nor thermal damage to the surrounding tissue. Explanted devices from two studies were free of thrombi and in the third study there were unattached thrombi on the SVC inlet of the rotor. The mini-FCAD was successfully tested in vivo as a right heart replacement device demonstrating adequate circulatory support and normal physiologic pulmonary and venous pressures.

A computationally efficient formal optimization of regional myocardial contractility in a sheep with left ventricular aneurysm.

A non-invasive method for estimating regional myocardial contractility in vivo would be of great value in the design and evaluation of new surgical and medical strategies to treat and/or prevent infarction-induced heart failure. As a first step towards developing such a method, an explicit finite element (FE) model-based formal optimization of regional myocardial contractility in a sheep with left ventricular (LV) aneurysm was performed using tagged magnetic resonance (MR) images and cardiac catheterization pressures. From the tagged MR images, 3-dimensional (3D) myocardial strains, LV volumes and geometry for the animal-specific 3D FE model of the LV were calculated, while the LV pressures provided physiological loading conditions. Active material parameters (T(max_B) and T(max_R)) in the non-infarcted myocardium adjacent to the aneurysm (borderzone) and in myocardium remote from the aneurysm were estimated by minimizing the errors between FE model-predicted and measured systolic strains and LV volumes using the successive response surface method for optimization. The significant depression in optimized T(max_B) relative to T(max_R) was confirmed by direct ex vivo force measurements from skinned fiber preparations. The optimized values of T(max_B) and T(max_R) were not overly sensitive to the passive material parameters specified. The computation time of less than 5 hours associated with our proposed method for estimating regional myocardial contractility in vivo makes it a potentially very useful clinical tool.

Cannula Tip With Integrated Volume Sensor for Rotary Blood Pump Control: Early-Stage Development.

The lack of direct measurement of left ventricular unloading is a significant impediment to the development of an automatic speed control system for continuous-flow left ventricular assist devices (cf-LVADs). We have developed an inlet cannula tip for cf-LVADs with integrated electrodes for volume sensing based on conductance. Four platinum-iridium ring electrodes were installed into grooves on a cannula body constructed from polyetheretherketone (PEEK). A sinusoidal current excitation waveform (250 µA pk-pk, 50 kHz) was applied across one pair of electrodes, and the conductance-dependent voltage was sensed across the second pair of electrodes. The conductance catheter was tested in an acute ovine model (n = 3) in conjunction with the HeartMate II rotary blood pump to provide circulatory support and unload the ventricle. Echocardiography was used to measure ventricular size during pump support for verification for the conductance measurements. The conductance measurements correlated linearly with the echocardiography dimension measurements more than the full range of pump support from minimum support to suction. This cannula tip will enable the development of automatic control systems to optimize pump support based on a real-time measurement of ventricular size.

Chronic In Vivo Test of a Right Heart Replacement Blood Pump for Failed Fontan Circulation.

An implantable rotary blood pump was developed to provide long-term mechanical right heart support for patients who have failing Fontan circulation. The objective of this study was to evaluate the pump in vivo in a 30 day sheep study. Pump speed was set at 3,900 rpm for the duration of the study, and pump power was between 4.3 and 4.6 W. The pump inlet pressures for the superior vena cava (SVC) and inferior vena cava (IVC) were 14 ± 15 and 11 ± 15 mm Hg, respectively, over the duration of the study. Hematocrit remained stable at 30% ± 4%. Partial thromboplastin time (PTT) steadily increased from 30 s preoperatively to a high of 59 s on postoperative day 20, while prothrombin time (PT) remained at 20 ± 2 s for the duration of the study. The implantation and postoperative recovery were successful, and the animal demonstrated normal physiologic pulmonary and venous pressures and cardiac output. On pump inspection, the IVC and SVC inlets were completely clear of any deposits, but there were small thrombi (approximately 0.5 mm diameter) between each of the three rotor blades and along 20% of the parting line of the two volute halves. A complete right heart bypass was performed, postoperative recovery was successful, and the pump demonstrated adequate circulatory support and normal physiologic pulmonary and venous pressures. This study was the first successful test of a right heart replacement device in a chronic animal study.

Characterization of mechanical behavior of a porcine pulmonary artery strip using a randomized uniaxial stretch and stretch-rate protocol.

BACKGROUND: Much of the experimental work in soft tissue mechanics has been focused on fitting approximate relations for specific tissue types from aggregate data on multiple samples of the tissue. Such relations are needed for modeling applications and have reasonable predictability - especially given the natural variance in specimens. There is, however, much theoretical and experimental work to be done in determining constitutive behaviors for particular specimens and tissues. In so doing, it may be possible to exploit the natural variation in tissue ultrastructure - so to relate ultrastructure composition to tissue behavior. Thus, this study focuses on an experimental method for determining constitutive behaviors and illustrates the method with analysis of a porcine pulmonary artery strip. The method characterizes the elastic part of the response (implicitly in terms of stretch) and the inelastic part in terms of short term stretch history (i.e., stretch-rate) Ht2, longer term stretch history Ht1, and time since the start of testing T. METHODS: A uniaxial testing protocol with a random stretch and random stretch-rate was developed. The average stress at a particular stretch was chosen as the hyperelastic stress response, and deviation from the mean at this particular stretch is chosen as the inelastic deviation. Multivariable Linear Regression Analysis (MLRA) was utilized to verify if Ht2, Ht1, and T are important factors for characterizing the inelastic deviation. For acquiring Ht2 and Ht1, an integral function type of stretch history was employed with time constants chosen from the relaxation spectrum of an identical size strip from the same tissue with the same orientation. Finally, statistical models that characterize the inelasticity were developed at various, nominal values of stretch, and their predictive capability was examined. RESULTS: Inelastic deviation from hyperelasticity was high (31%) for low stretch and declined significantly with increasing stretch to a nadir of 3.6% for a stretch of 1.7. The inelastic deviation then increased with increasing stretch at the same point in the stress-strain curve where stiffness began to increase strikingly. MLRA showed that T is a major inelastic parameter at low deformation. For moderate and high deformations, Ht2 and Ht1 were dominant. DISCUSSION: A randomized uniaxial testing protocol was applied to a strip of porcine pulmonary artery to characterize the elasticity and inelasticity of a soft tissue. We were successful in determining the elastic response and the factors that gave rise to the inelastic deviation. This investigation seeks methods to better define, phenomenologically, the elastic and inelastic behavior of soft tissues.

Determination of Reynolds Shear Stress Level for Hemolysis.

Reynolds shear stress (RSS) has served as a metric for the effect of turbulence on hemolysis. Forstrom (1969) and Sallam and Hwang (1984) determined the RSS threshold for hemolysis to be 50,000 and 4,000 dyne/cm, respectively, using a turbulent jet. Despite the order of magnitude discrepancy, the threshold by Sallam and Hwang has been frequently cited for hemolytic potential in blood pumps. We recreated a Sallam apparatus (SA) to resolve this discrepancy and provide additional data to be used in developing a more accurate hemolysis model. Hemolysis was measured over a large range of Reynolds numbers (Re) (Re = 1,000-80,000). Washed bovine red blood cells (RBCs) were injected into the free jet of phosphate buffered saline, and hemolysis was quantified using a percent hemolysis, Hp = h (100 - hematocrit [HCT])/Hb, where h (mg/dl) is free hemoglobin and Hb (mg/dl) is total hemoglobin. Reynolds shear stress was calculated using two-dimensional laser Doppler velocimetry. Reynolds shear stress of ≥30,000 dyne/cm corresponding to Re of ≥60,000 appeared to cause hemolysis (p < 0.05). This RSS is an order of magnitude greater than the RSS threshold that Sallam and Hwang suggested, and it is similar to Forstrom's RSS threshold. This study resolved a long-standing uncertainty regarding the critical values of RSS for hemolysis and may provide a foundation for a more accurate hemolysis model.

Continuous flow left ventricular pump support and its effect on regional left ventricular wall stress: finite element analysis study.

Left ventricular assist device (LVAD) support unloads left ventricular (LV) pressure and volume and decreases wall stress. This study investigated the effect of systematic LVAD unloading on the 3-dimensional myocardial wall stress by employing finite element models containing layered fiber structure, active contractility, and passive stiffness. The HeartMate II(®) (Thoratec, Inc., Pleasanton, CA) was used for LV unloading. The model geometries and hemodynamic conditions for baseline (BL) and LVAD support (LVsupport) were acquired from the Penn State mock circulatory cardiac simulator. Myocardial wall stress of BL was compared with that of LVsupport at 8,000, 9,000, 10,000 RPM, providing mean pump flow (Q(mean)) of 2.6, 3.2, and 3.7 l/min, respectively. LVAD support was more effective at unloading during diastole as compared to systole. Approximately 40, 50, and 60% of end-diastolic wall stress reduction were achieved at Q(mean) of 2.6, 3.2, and 3.7 l/min, respectively, as compared to only a 10% reduction of end-systolic wall stress at Q(mean) of 3.7 l/min. In addition, there was a stress concentration during systole at the apex due to the cannulation and reduced boundary motion. This modeling study can be used to further understand optimal unloading, pump control, patient management, and cannula design.

Effective ventricular unloading by left ventricular assist device varies with stage of heart failure: cardiac simulator study.

Although the use of left ventricular assist devices (LVADs) as a bridge-to-recovery (BTR) has shown promise, clinical success has been limited due to the lack of understanding the timing of implantation, acute/chronic device setting, and explantation. This study investigated the effective ventricular unloading at different heart conditions by using a mock circulatory system (MCS) to provide a tool for pump parameter adjustments. We tested the hypothesis that effective unloading by LVAD at a given speed varies with the stage of heart failure. By using a MCS, systematic depression of cardiac performance was obtained. Five different stages of heart failure from control were achieved by adjusting the pneumatic systolic/diastolic pressure, filling pressure, and systemic resistance. The Heart Mate II® (Thoratec Corp., Pleasanton, CA) was used for volumetric and pressure unloading at different heart conditions over a given LVAD speed. The effective unloading at a given LVAD speed was greater in more depressed heart condition. The rate of unloading over LVAD speed was also greater in more depressed heart condition. In conclusion, to get continuous and optimal cardiac recovery, timely increase in LVAD speed over a period of support is needed while avoiding the akinesis of aortic valve.

Rotary blood pump control using integrated inlet pressure sensor.

Due to improved reliability and reduced risk of thromboembolic events, continuous flow left ventricular assist devices are being used more commonly as a long term treatment for end-stage heart failure. As more and more patients with these devices are leaving the hospital, a reliable control system is needed that can adjust pump support in response to changes in physiologic demand. An inlet pressure sensor has been developed that can be integrated with existing assist devices. A control system has been designed to adjust pump speed based on peak-to-peak changes in inlet pressure. The inlet pressure sensor and control system have been tested with the HeartMate II axial flow blood pump using a mock circulatory loop and an active left ventricle model. The closed loop control system increased total systemic flow and reduced ventricular load following a change in preload as compared to fixed speed control. The increase in systemic flow occurred under all operating conditions, and maximum unloading occurred in the case of reduced ventricular contractility.

Comparison of porcine pulmonary and aortic root material properties.

BACKGROUND: The pulmonary autograft remodels when subjected to systemic pressure and subsequent dilation can lead to reoperation. Inherent material property differences between pulmonary and aortic roots may influence remodeling but are currently unknown. The objective of this study was to determine stiffness across a wide range of strain and compare nonlinear material properties of corresponding regions of native aortic and pulmonary roots. METHODS: Tissue samples from porcine aortic and pulmonary roots-sinuses and supravalvular artery distal to the sinotubular junction-were subjected to displacement-controlled equibiaxial stretch testing. Stress-strain data recorded were used to derive strain energy functions for each region. Stiffness from low to high strains at 0.15, 0.3, and 0.5 strain were determined for comparisons. RESULTS: Aortic and pulmonary roots exhibited qualitatively similar material properties; both had greater nonlinearity in the sinus than supravalvular artery. The pulmonary artery was significantly more compliant than the ascending aorta both circumferentially and longitudinally throughout the strain range (p < 0.03), except at high strain circumferentially (p = 0.06). However, no differences in stiffness were seen circumferentially or longitudinally between pulmonary and aortic sinuses (p > or = 0.3) until high strain, when the pulmonary sinuses were significantly stiffer (p < 0.05) in both directions. CONCLUSIONS: Differences in stiffness between porcine aortic and pulmonary roots are regionally specific, supravalvular artery versus sinus. These regional differences may impact the mode of remodeling to influence late autograft dilation.

Effect of adjustable passive constraint on the failing left ventricle: a finite-element model study.

BACKGROUND: Passive constraint is used to prevent left ventricular dilation and subsequent remodeling. However, there has been concern about the effect of passive constraint on diastolic left ventricular chamber stiffness and pump function. This study determined the relationship between constraint, diastolic wall stress, chamber stiffness, and pump function. We tested the hypothesis that passive constraint at 3 mm Hg reduces wall stress with minimal change in pump function. METHODS: A three-dimensional finite-element model of the globally dilated left ventricle based on left ventricular dimensions obtained in dogs that had undergone serial intracoronary microsphere injection was created. The model was adjusted to match experimentally observed end-diastolic left ventricular volume and midventricular wall thickness. The experimental results used to create the model were previously reported. A pressure of 3, 5, 7, and 9 mm Hg was applied to the epicardium. Fiber stress, end-diastolic pressure-volume relationship, end-systolic pressure-volume relationship, and the stroke volume-end-diastolic pressure (Starling) relationship were calculated. RESULTS: As epicardial constraint pressure increased, fiber stress decreased, the end-diastolic pressure-volume relationship shifted to the left, and the Starling relationship shifted down and to the right. The end-systolic pressure-volume relationship did not change. A constraining pressure of 2.3 mm Hg was associated with a 10% reduction in stroke volume, and mean end-diastolic fiber stress was reduced by 18.3% (inner wall), 15.3% (mid wall), and 14.2% (outer wall). CONCLUSIONS: Both stress and cardiac output decrease in a linear fashion as the amount of passive constraint is increased. If the reduction in cardiac output is to be less than 10%, passive constraint should not exceed 2.3 mm Hg. On the other hand, this amount of constraint may be sufficient to reverse eccentric hypertrophy after myocardial infarction.

Planar biaxial mechanical behavior of bioartificial tissues possessing prescribed fiber alignment.

Though it is widely accepted that fiber alignment has a great influence on the mechanical anisotropy of tissues, a systematic study of the influence of fiber alignment on the macroscopic mechanical behavior by native tissues is precluded due to their predefined microstructure and heterogeneity. Such a study is possible using collagen-based bioartificial tissues that allow for alignment to be prescribed during their fabrication. To generate a systemic variation of strength of fiber alignment, we made cruciform tissue constructs in Teflon molds that had arms of different aspect ratios. We implemented our anisotropic biphasic theory of tissue-equivalent mechanics to simulate the compaction by finite element analysis. Prior to tensile testing, the construct geometry was standardized by cutting test samples with a 1:1 cruciform punch after releasing constructs from the molds. Planar biaxial testing was performed on these samples, after stretching them to their in-mold dimensions to recover in-mold alignment, to observe the macroscopic mechanical response with simultaneous fiber alignment imaging using a polarimetry system. We found that the strength of fiber alignment of the samples prior to release from the molds linearly increased with anisotropy of the mold. In testing after release, modulus ratio (modulus in fiber direction/modulus in normal direction) was greater as the initial strength of fiber alignment increased, that is, as the aspect ratio increased. We also found that the fiber alignment strength and modulus ratio increased in a hyperbolic fashion with stretching for a sample of given aspect ratio.