Microcavity induced by a few-layer GaSe crystal on a silicon photonic crystal waveguide for efficient optical frequency conversion.

We demonstrate the post-induction of high-quality microcavities on a silicon photonic crystal (PC) waveguide by integrating a few-layer GaSe crystal, which promises efficient on-chip optical frequency conversions. The integration of GaSe shifts the dispersion bands of the PC waveguide mode into the bandgap, resulting in localized modes confined by the bare PC waveguides. Thanks to the small contrast of refractive index at the boundaries of the microcavity, it is reliable to obtain quality factors exceeding 104. With the enhanced light-GaSe interaction by the microcavity modes and GaSe's high second-order nonlinearity, remarkable second-harmonic generation (SHG) and sum-frequency generation (SFG) are achieved with continuous-wave (CW) lasers.

Compact and high-reliability fiber-optic open-loop gyroscope enabled by an in-fiber polarizer.

The performance of an open-loop fiber-optic gyroscope is strongly dependent on the optical characteristics of its polarizer. Here we report the implementation of an in-house fabricated 45° tilted-fiber-grating-based polarizer, for the first time on an ultra-fine diameter polarization-maintaining fiber platform in an open-loop fiber-optic gyroscope. This special in-line polarizer is proven to have the merits of high extinction ratio, broad spectrum, bendability, stretchability, temperature insensitivity, and high reliability, all of which make it a perfect match for practical fiber optic gyros that need to be packaged compactly without affecting performance. Our prototype fiber optic gyroscope has a compact volume of only ϕ35 × 20 mm2, achieving a bias instability of less than 0.1 °/h, full temperature bias stability of less than 1 °/h, and scale factor linearity of better than 200 ppm. This compact and high-performance fiber gyro enabled by TFG polarizer may promise great potential in the field of automation and control.

Tilted fiber grating polarizer in a 40-µm polarization-maintaining fiber.

The optical polarizer is a crucial component widely used in many optical systems and applications. Fiber-optic polarizers have the merits of excellent compatibility and ease of integration with other fiber components. We report an in-line polarizer enabled by a 45° tilted fiber grating inscribed into a specialty fiber for the next generation fiber-optic gyroscope, i.e., a 40-µm ultra-fine-diameter tiger-type polarization-maintaining fiber with which the size of fiber-optic sensors can be miniaturized. The results show that a 40-mm-long polarizer operates at a center wavelength of around 830 nm with high-performance characteristics, such as a polarization extinction ratio exceeding 30 dB, a low insertion loss of less than 1.5 dB, and a large 3-dB optical bandwidth more than 60 nm. This kind of fiber-optic polarizer may have a broad scope across applications and systems such as fiber lasers and sensors, especially high-precision fiber-optic gyroscopes.

Digital Control and Demodulation Algorithm for Compact Open-Loop Fiber-Optic Gyroscope.

With the advantages of small size, low cost, and moderate accuracy, an open-loop fiber-optic gyroscope (FOG) has a wide range of applications around control and automation. For the most cost-sensitive applications, a simple and stable digital algorithm with a reduced control-circuit volume and cost is highly desirable to realize high-precision control of a FOG. In this work, a new algorithm for an open-loop FOG is proposed based on the discrete multi-point demodulation in the sinusoidal modulation period. Utilizing this algorithm, stable control and angular velocity calculation of a gyro are realized with effectively suppressed gyro error. The use of this algorithm greatly reduces the requirements for processing power and simplifies the gyro circuit. Based on this algorithm, a digital FOG with a volume of only 25 × 20 × 40 mm3 achieves a bias instability of less than 0.15°/h, an angle random walk (ARW) of less than 0.015°/√h, a start-up time of less than 1 s, and a 3 dB bandwidth beyond 160 Hz. This low-cost, compact, and high-performance gyro is sufficient to satisfy the requirements of applications in the navigation and control fields such as unmanned driving.

Strong cladding mode excitation in ultrathin fiber inscribed Bragg grating with ultraviolet photosensitivity.

Strong UV-written Bragg gratings written in 50 µm-diameter cladding single mode fibers compatible with conventional fiber couple core guided light to dozens of cladding modes distributed across 140 nm in the 1400-1600 nm region, without the need for complex symmetry breaking mechanisms such as tilted, laterally offset, or localized gratings. The extent of the coupling to high order modes and the smaller cladding diameter both contribute to increasing the sensitivity to surrounding refractive index changes by more than one order of magnitude, and to an increased spacing between mode resonances to facilitate unambiguous measurements of larger index changes between 1.3 and 1.44. These improvements are confirmed by theoretical and experimental studies that also cover the temperature and strain differential sensitivities of the cladding mode resonances for complete multiparameter sensing capability.

Suspended-core fiber with embedded GaSe nanosheets for second harmonic generation.

We report an all-fiber scheme for the second harmonic generation (SHG) by embedding gallium selenide (GaSe) nanosheets into a suspended-core fiber (SCF). Based on modes analysis and theoretical calculations, the phase-matching modes from multiple optional modes in the SHG process and the optimal SCF length are determined by calculating the effective refractive index and balancing the SHG growth and transmission loss. Due to the long-distance interaction between pumped fundamental mode and GaSe nanosheets around the suspended core, an SHG signal is observed under a milliwatt-level pump light, and exhibits a quadratic growth with the increased pump power. The SHG process is also realized in a broad wavelength range by varying the pump in the range of 1420∼1700 nm. The SCF with the large air cladding and suspended core as an excellent platform can therefore be employed to integrate low-dimensional nonlinear materials, which holds great promise for the applications of all-fiber structures in new light source generating, signal processing and fiber sensing.

Dynamic strain measurement based on ultrafast Brillouin collision in the correlation domain.

The Brillouin collision rate in a Brillouin optical correlation domain analysis fiber sensor is ultimately limited by the sensing fiber length, which restricts the single point sampling rate in dynamic strain measurement. Here, a time-gated long-phase-sequence-coded pump method is proposed to overcome this limitation. The Brillouin collision rate is limited only by the phonon lifetime, since it governs the building and decaying time of the acoustic wave. For a sensing fiber length of ∼1km, a Brillouin collision rate as high as 1 MHz is experimentally realized. This further results in a single-point sampling rate of 1 kHz for dynamic strain sensing with a spatial resolution of ∼2cm and a measurement uncertainty of <33.5µÎµ.

Phase fluctuation cancellation for coherent-detection BOTDA fiber sensors based on optical subcarrier multiplexing.

The employment of coherent detection in a Brillouin optical time domain analysis (BOTDA) fiber sensor brings benefits, including signal-to-noise ratio enhancement, non-local effect reduction, and sensing speed improvement. Recently, it was found that the performance of a coherent-detection BOTDA fiber sensor suffers from phase fluctuations introduced by the fiber group delay jitter. Here, we propose a phase fluctuation cancellation approach based on optical subcarrier multiplexing. In a proof-of-concept experiment, the phase stability for in-phase/quadrature demodulation reaches a standard deviation value of as small as 0.4 mrad. The variations in the Brillouin gain and phase spectra caused by the phase fluctuation are then effectively alleviated, resulting in an enhancement of the Brillouin frequency shift measurement certainty along the whole sensing fiber.

Continuous-wave pumped frequency upconversions in an InSe-integrated microfiber.

We report the achievement of continuous-wave (CW)-pumped second-harmonic generation (SHG) and sum frequency generation (SFG) in a layered indium selenide (InSe)-integrated microfiber. As a result of the strong interaction between the InSe nanosheets and the evanescent field, the second-order nonlinear processes are greatly enhanced in the InSe-integrated microfiber pumped by a few milliwatt CW lasers. The experimental results reveal that the intensities of SHG and SFG are quadratic and linear dependencies with the incident pump power, respectively, which is consistent with theoretical predictions. Additionally, the SHG intensity is strongly polarization-dependent on the nonaxisymmetrical distribution of the InSe nanosheets around the microfiber, providing the possibility of the SHG-polarized manipulation. The proposed device has the potential to be integrable into all-fiber systems for nonlinear applications.

Temperature-compensated fiber directional-bend sensor based on a sandwiched MMF-PMPCF structure.

An optical fiber directional-bend sensor based on an inline Mach-Zehnder interferometer is proposed and demonstrated. The device consists of a piece of a multimode fiber (MMF) splicing with a polarization-maintaining photonic crystal fiber (PMPCF) and sandwiched by lead in/out single-mode fibers (SMFs). Owing to the larger diameter of the MMF, some high-order modes in fiber are efficiently coupled and transmitted through the PMPCF, and finally interfere with each other in the output SMFs. The experimental results show that a well-defined interference fringe envelope can be obtained in the transmitted spectrum and, when the fiber is bent, both the intensity and the fringe visibility of the interference pattern are changed with the bending curvature. Meanwhile, the bend sensitivities are varied with different bending directions, and the maximum sensitivity is achieved up to -8.33dB/m-1 within the bend range from 0 to 1.7m-1. The proposed device also demonstrates a very low-intensity cross-talk of environment temperature.

Co-located angularly offset fiber Bragg grating pair for temperature-compensated unambiguous 3D shape sensing.

A 10 mm-long three-dimensional shape sensor in a single-mode fiber is described and demonstrated experimentally. The sensor is based on a pair of fiber Bragg gratings inscribed at the same location along the fiber axis but offset along different radial directions away from the fiber center. Each offset grating generates cladding mode resonances over a ${\sim}{20}\;{\rm{nm}}$-wide spectral bandwidth, and the two gratings are also offset in period so that their transmission spectra are separated by 40 nm, and thus non-overlapping and fully distinguishable. Directional bending sensitivity results from the differential amplitude response of the cladding mode resonances from the two gratings, depending on the relative orientation of the bend with the azimuthal direction of the grating offsets. It is further demonstrated that both axial deformation and temperature have no influence on the shape measurement as they both only cause a global wavelength shift of the spectra without amplitude change. The experimental results demonstrate that the shape orientation of an object can be unambiguously determined for bend directions covering the full 360° range around the fiber axis with sensitivities of the order of ${{1}}\;{\rm{dB/}}{{\rm{m}}^{- 1}}$ and small curvatures between 0 and ${{1}}\;{{\rm{m}}^{- 1}}$.

Symmetry selective cladding modes coupling in ultrafast-written fiber Bragg gratings in two-mode fiber.

The lower order cladding mode resonances of a fiber Bragg grating (FBG) are sensitive to fiber bending but their spectral density makes their response to bending very complex. In this work we present a simple method to reduce and control the number of low order cladding mode resonances via FBGs written in a two-mode fiber (TMF) with an ultrafast laser. Owing to the larger core size of the TMF, a slight break of the cylindrical asymmetry of the grating patterns can be induced when using femtosecond side-irradiation with a small change in the writing condition. This allows us to control the mode families coupled by the grating, and in particular to those modes that have positive or negative bending responses along certain bend directions. Experimental results demonstrate that several lower-order neighboring-cladding mode pairs coupled by the asymmetric TMFBG have antagonistic loss responses (by several dB) for different bending directions, thus allowing full 2D bending measurements with many applications in shape sensing. Finally, this device has similar advantages as tilted FBGs, i.e. temperature de-correlation and the possibility of increasing the signal to noise ratio by averaging simultaneous measurements on several pairs of resonances.

Simultaneous measurement of refractive index and temperature with high sensitivity based on a multipath fiber Mach-Zehnder interferometer.

We present and experimentally demonstrate a highly sensitive sensor for simultaneously measuring the refractive index (RI) and temperature based on a multipath fiber Mach-Zehnder interferometer. The sensor is fabricated by sandwiching a segment of weak-coupling seven-core fiber (SCF) with two short multimode fibers, and then splicing it with lead-in and lead-out single-mode fibers, respectively. Six outer cores of the SCF are half-etched chemically for enhancing the interaction between light and matter. A high-quality transmission spectrum with 23 dB fringe visibility is obtained. Due to the strong interaction between the outer core modes and cladding modes with the surrounding medium, the proposed fiber structure exhibits not only an extremely high RI sensitivity of -1802.26 nm/RI unit from 1.427 to 1.442, but also a superior temperature sensitivity of 82 pm/°C from 10°C to 90°C. Moreover, RI and temperature can be discriminated simultaneously by measuring the central wavelength shifts of two transmission notches. This sensor has outstanding advantages of high sensitivity, easy fabrication, simple structure, and low cost, and may find applications in multiparameter highly sensitive sensing.

All-fiber radially/azimuthally polarized lasers based on mode coupling of tapered fibers.

We demonstrate a mode converter with an insertion loss of 0.36 dB based on mode coupling of tapered single-mode and two-mode fibers, and realize all-fiber flexible cylindrical vector lasers at 1550 nm. Attributing to the continuous distribution of a tangential electric field at taper boundaries, the laser is switchable between the radially and azimuthally polarized states by adjusting the input polarization. In the temporal domain, the operation is controllable among continuous-wave, Q-switched, and mode-locked statuses by changing the saturable absorber or pump strength. The duration of Q-switched radially/azimuthally polarized laser spans from 10.4/10.8 to 6/6.4 µs at the pump range of 38 to 58 mW, while that of the mode-locked pulse varies from 39.2/31.9 to 5.6/5.2 ps by controlling the laser bandwidth. The proposed laser combines the features of a cylindrical vector beam, a fiber laser, and an ultrafast pulse, providing a special and cost-effective source for practical applications.

Simultaneous directional curvature and temperature sensor based on a tilted few-mode fiber Bragg grating.

We demonstrate a directional curvature sensor based on tilted few-mode fiber Bragg gratings (FM-FBGs) inscribed by a UV laser. The eigenmodes of LP01 and LP11 mode groups are simulated along with the fiber bending. The directional curvature sensor is based on the LP11 mode resonance in the tilted FM-FBG. For curvature from 4.883 to 7.625 m-1, the curvature sensitivities at direction of 0° and 90° are measured to be -2.67 and 0.128 dB/m-1, respectively. The temperature variation barely affects the resonance depth of LP11 mode. The proposed curvature sensor clearly demonstrates the potential to simultaneous directional curvature and temperature measurement with the resolutions of 9.15×10-4 m-1 and 0.952°C, respectively.

Temperature-calibrated high-precision refractometer using a tilted fiber Bragg grating.

We present a refractometer with main- and vernier-scale to measure the refractive index (RI) of liquids with high precision by using the fine spectrum structure of a tilted fiber Bragg grating (TFBG). The absolute RI values are determined by the accurate wavelength of cut-off mode resonances. The main- and vernier-scale are calibrated by measuring large groups of fine spectra at different cut-off mode resonances in a small RI range, and the use of vernier-scale certainly reduces the RI measurement uncertainty resulted from the discrete cladding mode resonances. The performance of the TFBG-based vernier refractometer is experimentally verified by exploring the temperature dependence of RI of anhydrous ethanol in a near infrared region, showing an enhanced accuracy to the order of 10-4, high repeatability and temperature self-calibration capability.

Multi-channel mode converter based on a modal interferometer in a two-mode fiber.

In this Letter, we propose a multi-channel mode converter with the concept of a modal interferometer in a two-mode fiber (TMF). Two lateral stress points in a TMF function as in-line fiber mode couplers to construct the modal interferometer, and both transmission spectra and near-field patterns confirm that the LP01 mode is successfully converted into an LP11 mode at the multiple channels. The measured mode conversion efficiency almost completely follows the theoretical tendency. Finally, the mode conversion is realized at 20 channels in the C+L wavelength band with conversion efficiency up to 99.5% and insertion loss as low as 0.6 dB. Furthermore, the channel spacing can be freely tailored by adjusting the distance between two stress points.

Optical vortex generation with wavelength tunability based on an acoustically-induced fiber grating.

We presented a method to actualize the optical vortex generation with wavelength tunability via an acoustically-induced fiber grating (AIFG) driven by a radio frequency source. The circular polarization fundamental mode could be converted to the first-order optical vortex through the AIFG, and its topological charges were verified by the spiral pattern of coaxial interference between the first-order optical vortex and a Gaussian-reference beam. A spectral tuning range from 1540 nm to 1560 nm was demonstrated with a wavelength tunability slope of 4.65 nm/kHz. The mode conversion efficiency was 95% within the whole tuning spectral range.

Cylindrical vector beam generation in fiber with mode selectivity and wavelength tunability over broadband by acoustic flexural wave.

Theoretical analysis and experimental demonstration are presented for the generation of cylindrical vector beams (CVBs) via mode conversion in fiber from HE11 mode to TM01 and TE01 modes, which have radial and azimuthal polarizations, respectively. Intermodal coupling is caused by an acoustic flexural wave applied on the fiber, whereas polarization control is necessary for the mode conversion, i.e. HE11x→TM01 and HE11y→TE01 for acoustic vibration along the x-axis. The frequency of the RF driving signal for actuating the acoustic wave is determined by the phase matching condition that the period of acoustic wave equals the beatlength of two coupled modes. With phase matching condition tunability, this approach can be used to generate different types of CVBs at the same wavelength over a broadband. Experimental demonstration was done in the visible and communication bands.

Graphene-induced unique polarization tuning properties of excessively tilted fiber grating.

By exploiting the polarization-sensitive coupling effect of graphene with the optical mode, we investigate the polarization modulation properties of a hybrid waveguide of graphene-integrated excessively tilted fiber grating (Ex-TFG). The theoretical analysis and experimental results demonstrate that the real and imaginary parts of complex refractive index of few-layer graphene exhibit different effects on transverse electric (TE) and transverse magnetic (TM) cladding modes of the Ex-TFG, enabling stronger absorption in the TE mode and more wavelength shift in the TM mode. Furthermore, the surrounding refractive index can modulate the complex optical constant of graphene and then the polarization properties of the hybrid waveguide, such as resonant wavelength and peak intensity. Therefore, the unique polarization tuning property induced by the integration of the graphene layer with Ex-TFG may endow potential applications in all-in-one fiber modulators, fiber lasers, and biochemical sensors.