Stepwise Curing Induced All-Stretchable Thermoelectric Generator of High Power Density.

In this study, a wearable and highly stretchable organic thermoelectric (TE) generator with a notable power density is developed. A highly stretchable and solution-processable TE/electrode pattern is realized by stepwise-curing elastomeric and conducting network. Significant advances in the TE or electrical properties are obtained for these stretchable patterns through post-activation treatment, which creates long-range charge transport pathways without degrading pre-established elastomeric networks. The TE and electrode patterns are solution-processed to a stretchable template, so that all-stretchable TE generator is realized. The fabricated TE generator maintains 90% of its maximum TE power output at 40% stretching stress and shows a stable TE power output after 200 stretching cycles. The TE generator maintains its stretchability in highly densified patterns, as the highly stretchable TE/electrode patterns enable good stretchability with little aid of the stretchable template. So, the TE generator has a high power density of 0.32 nW cm-2 K-2, one of the highest values among stretchable TE generators to date.

Novel Dithienopyrrole-Based Conjugated Copolymers: Importance of Backbone Planarity in Achieving High Electrical Conductivity and Thermoelectric Performance.

The development of conjugated polymers with structures that are suitable for efficient molecular doping and charge transport is a key challenge in the construction of high-performance conjugated polymer-based thermoelectric devices. In this study, three novel conjugated polymers based on dithienopyrrole (DTP) are synthesized and their thermoelectric properties are compared. When doped with p-dopant, a donor-acceptor type copolymer, DPP-MeDTP, exhibits higher electrical conductivity and thermoelectric power factor compared to the other donor-donor type copolymers. The high electrical conductivity of DPP-MeDTP compared to the other polymers originates from the high degree of backbone planarity and molecular order, which contributes to its high charge carrier mobility. In addition, the highly crystalline structure of DPP-MeDTP is well maintained upon doping, while the crystalline order of the other polymers decreases significantly upon doping. The findings of this work not only provide insights into the design of DTP-based conjugated polymers for thermoelectric use but also demonstrate the significance of a high degree of molecular order and structural robustness upon doping to achieve high thermoelectric performance.

π-Extended Thiazole-Containing Polymer Semiconductor for Balanced Charge-Carrier Mobilities.

A low-band gap semiconducting polymer with an acceptor-donor-acceptor architecture is newly designed and synthesized by incorporating a π-extended thiazole-vinylene-thiazole unit. The resulting thiazole-containing diketopyrrolopyrrole copolymer exhibits well-balanced ambipolar characteristics with hole mobility of up to 0.11 cm2 V-1 s-1 and electron mobility of up to 0.30 cm2 V-1 s-1 , which are suitable for applications in polymer electronics.

Studies on the concentrations of particulate matter and ammonia gas from three laying hen rearing systems during the summer season.

This study aimed to measure the concentrations of particulate matter (PM10, PM2.5) and ammonia gas (NH3) from different types of laying hen houses during summer. The treatment groups included conventional cage, floor pens, and aviary system, with tunnel ventilation system applied to all poultry houses. The PM10 concentration was highest in the aviary system from 10:00 h to 18:30 h, whereas in the cage, it remained high after 18:30 h until 7:30 h the next day. The cage showed high levels of PM2.5 from 18:30 h to 7:30 h the next day. The correlation between the three breeding systems showed an R2 < 0.2. The mean daily concentrations of PM10, PM2.5, and NH3 were highest in the cage, among all the poultry houses. On comparing the two welfare breeding systems (floor pens and aviary system), particulate matter concentrations were higher in the floor pens, while the aviary system had higher level of NH3. However, no significant differences were observed between the concentrations of PM10, PM2.5, and NH3 between the three laying hen houses in summer. This study provides basic data for improving the rearing environment in the three different types of poultry housing systems.

Electric-Field-Tunable Growth of Organic Semiconductor Crystals on Graphene.

Growth of organic semiconductor thin films on a two-dimensional template is affected by its properties and is not well understood. This growth process dictates a thin film's final morphology and crystal structure and is controlled by the interactions between ad-molecules and the template. Here, we report that the template's charge density determines the tuning of such interactions. We observe the dependence of pentacene nucleation on charge carrier density ng in graphene under an applied electric field and contact-doping and then deduce that the interaction energy EA between the ad-molecule and the graphene is related linearly to ng. This tunability of EA allows control of the pentacene crystals growth. We exploit these findings to demonstrate that graphene, in which ng is controlled, can be used to template pentacene thin films for improved optoelectronic properties, such as electrical conductivity and exciton diffusion length.

Controllable Bipolar Doping of Graphene with 2D Molecular Dopants.

The fine control of graphene doping levels over a wide energy range remains a challenging issue for the electronic applications of graphene. Here, the controllable doping of chemical vapor deposited graphene, which provides a wide range of energy levels (shifts up to ± 0.5 eV), is demonstrated through physical contact with chemically versatile graphene oxide (GO) sheets, a 2D dopant that can be solution-processed. GO sheets are a p-type dopant due to their abundance of electron-withdrawing functional groups. To expand the energy window of GO-doped graphene, the GO surface is chemically modified with electron-donating ethylene diamine molecules. The amine-functionalized GO sheets exhibit strong n-type doping behaviors. In addition, the particular physicochemical characteristics of the GO sheets, namely their sheet sizes, number of layers, and degree of oxidation and amine functionality, are systematically varied to finely tune their energy levels. Finally, the tailor-made GO sheet dopants are applied into graphene-based electronic devices, which are found to exhibit improved device performances. These results demonstrate the potential of GO sheet dopants in many graphene-based electronics applications.

Bistable Solid-State Fluorescence Switching in Photoluminescent, Infinite Coordination Polymers.

Photo-functional infinite coordinated polymers (ICPs) were synthesized that consist of the photochromic dithienylethene (DTE) and a luminescent bridging unit to give enhanced fluorescence in the solid state. We could fabricate well-ordered micropatterns of these ICPs by a soft-lithographic method, which repeatedly showed high contrast on-off fluorescence switching.

Side-Chain-Induced Rigid Backbone Organization of Polymer Semiconductors through Semifluoroalkyl Side Chains.

While high-mobility p-type conjugated polymers have been widely reported, high-mobility n-type conjugated polymers are still rare. In the present work, we designed semifluorinated alkyl side chains and introduced them into naphthalene diimide-based polymers (PNDIF-T2 and PNDIF-TVT). We found that the strong self-organization of these side chains induced a high degree of order in the attached polymer backbones by forming a superstructure composed of "backbone crystals" and "side-chain crystals". This phenomenon was shown to greatly enhance the ordering along the backbone direction, and the resulting polymers thus exhibited unipolar n-channel transport in field-effect transistors with remarkably high electron mobility values of up to 6.50 cm(2) V(-1) s(-1) and with a high on-off current ratio of 10(5).

Atomically thin epitaxial template for organic crystal growth using graphene with controlled surface wettability.

A two-dimensional epitaxial growth template for organic semiconductors was developed using a new method for transferring clean graphene sheets onto a substrate with controlled surface wettability. The introduction of a sacrificial graphene layer between a patterned polymeric supporting layer and a monolayer graphene sheet enabled the crack-free and residue-free transfer of free-standing monolayer graphene onto arbitrary substrates. The clean graphene template clearly induced the quasi-epitaxial growth of crystalline organic semiconductors with lying-down molecular orientation while maintaining the "wetting transparency", which allowed the transmission of the interaction between organic molecules and the underlying substrate. Consequently, the growth mode and corresponding morphology of the organic semiconductors on graphene templates exhibited distinctive dependence on the substrate hydrophobicity with clear transition from lateral to vertical growth mode on hydrophilic substrates, which originated from the high surface energy of the exposed crystallographic planes of the organic semiconductors on graphene. The optical properties of the pentacene layer, especially the diffusion of the exciton, also showed a strong dependency on the corresponding morphological evolution. Furthermore, the effect of pentacene-substrate interaction was systematically investigated by gradually increasing the number of graphene layers. These results suggested that the combination of a clean graphene surface and a suitable underlying substrate could serve as an atomically thin growth template to engineer the interaction between organic molecules and aromatic graphene network, thereby paving the way for effectively and conveniently tuning the semiconductor layer morphologies in devices prepared using graphene.

Variance Component Quantitative Trait Locus Analysis for Body Weight Traits in Purebred Korean Native Chicken.

Quantitative trait locus (QTL) is a particular region of the genome containing one or more genes associated with economically important quantitative traits. This study was conducted to identify QTL regions for body weight and growth traits in purebred Korean native chicken (KNC). F1 samples (n = 595) were genotyped using 127 microsatellite markers and 8 single nucleotide polymorphisms that covered 2,616.1 centi Morgan (cM) of map length for 26 autosomal linkage groups. Body weight traits were measured every 2 weeks from hatch to 20 weeks of age. Weight of half carcass was also collected together with growth rate. A multipoint variance component linkage approach was used to identify QTLs for the body weight traits. Two significant QTLs for growth were identified on chicken chromosome 3 (GGA3) for growth 16 to18 weeks (logarithm of the odds [LOD] = 3.24, Nominal p value = 0.0001) and GGA4 for growth 6 to 8 weeks (LOD = 2.88, Nominal p value = 0.0003). Additionally, one significant QTL and three suggestive QTLs were detected for body weight traits in KNC; significant QTL for body weight at 4 weeks (LOD = 2.52, nominal p value = 0.0007) and suggestive QTL for 8 weeks (LOD = 1.96, Nominal p value = 0.0027) were detected on GGA4; QTLs were also detected for two different body weight traits: body weight at 16 weeks on GGA3 and body weight at 18 weeks on GGA19. Additionally, two suggestive QTLs for carcass weight were detected at 0 and 70 cM on GGA19. In conclusion, the current study identified several significant and suggestive QTLs that affect growth related traits in a unique resource pedigree in purebred KNC. This information will contribute to improving the body weight traits in native chicken breeds, especially for the Asian native chicken breeds.

Controlling Fluorination Density of Soluble Polyimide Gate Dielectrics and its Influence on Organic Crystal Growth and Device Operational Stability.

Fluorinated polyimides (PIs) are among the most promising candidates for gate dielectric materials in organic electronic devices because of their solution processability and outstanding chemical, mechanical, and thermal stabilities. Additionally, fluorine (F) substitution improves the electrical properties of PI thin films, such as enhanced dielectric properties and reduced surface trap densities. However, the relationship between the fluorination density of PIs and crystal growth modes of vacuum-deposited conjugated molecules on PI thin films, which is directly related to the lateral charge transport along the PI-organic semiconductor interface, has not been systematically studied. Herein, five different soluble PIs with different F densities were synthesized, and the correlation between fluorination and thin-film properties was systematically investigated. Not only were their dielectric properties modulated, but the growth modes of the organic molecules deposited on the PI thin films also changed with increasing surface F density. This phenomenon was observed by both surface and crystallographic analyses, which resulted in extremely high operational stability of field-effect transistors and the successful fabrication of organic complementary circuits. We believe that the correlation between PI backbone fluorination and its thin-film properties will provide practical insights into the material design based on controlled molecular directed surface assembly on fluorinated polymer dielectrics.

One-Shot Remote Integration of Macromolecular Synaptic Elements on a Chip for Ultrathin Flexible Neural Network System.

The field of biomimetic electronics that mimic synaptic functions has expanded significantly to overcome the limitations of the von Neumann bottleneck. However, the scaling down of the technology has led to an increasingly intricate manufacturing process. To address the issue, this work presents a one-shot integrable electropolymerization (OSIEP) method with remote controllability for the deposition of synaptic elements on a chip by exploiting bipolar electrochemistry. Condensing synthesis, deposition, and patterning into a single fabrication step is achieved by combining alternating-current voltage superimposed on direct-current voltage-bipolar electropolymerization and a specially designed dual source/drain bipolar electrodes. As a result, uniform 6 × 5 arrays of poly(3,4-ethylenedioxythiophene) channels are successfully fabricated on flexible ultrathin parylene substrates in one-shot process. The channels exhibited highly uniform characteristics and are directly used as electrochemical synaptic transistor with synaptic plasticity over 100 s. The synaptic transistors have demonstrated promising performance in an artificial neural network (NN) simulation, achieving a high recognition accuracy of 95.20%. Additionally, the array of synaptic transistor is easily reconfigured to a multi-gate synaptic circuit to implement the principles of operant conditioning. These results provide a compelling fabrication strategy for realizing cost-effective and disposable NN systems with high integration density.

High-Throughput Roll-to-Roll Processed Large-Area Perovskite Solar Cells Using Rapid Radiation Annealing Technique.

The development of a stable roll-to-roll (R2R) process for flexible large-area perovskite solar cells (PSCs) and modules is a pressing challenge. In this study, we introduced a new R2R PSC manufacturing system that employs a two-step deposition method for coating perovskite and uses intensive pulsed light (IPL) for annealing. This system has successfully fabricated small-sized cells and the first-ever large-sized, R2R-processed flexible modules. A key focus of our work was to accelerate the conversion of PbI2 to perovskite. To this end, we utilized IPL annealing and incorporated additives into the PbI2 layer. With these modifications, the R2R-processed perovskite films achieved a power conversion efficiency (PCE) of 16.87%, representing the highest reported value for R2R two-step processed PSCs. However, these cells exhibited hysteresis in reverse and forward PCE measurements. To address this, we introduced a dual-annealing process consisting of IPL followed by a 2-min thermal heating step. This approach successfully reduced hysteresis, resulting in low-hysteresis, R2R-processed flexible PSCs. Moreover, we fabricated large-scale flexible modules (10 × 10 cm2) with a PCE of 11.25% using the dual-annealing system, marking a significant milestone in this field.

Free-standing two-dimensional ferro-ionic memristor.

Two-dimensional (2D) ferroelectric materials have emerged as significant platforms for multi-functional three-dimensional (3D) integrated electronic devices. Among 2D ferroelectric materials, ferro-ionic CuInP2S6 has the potential to achieve the versatile advances in neuromorphic computing systems due to its phase tunability and ferro-ionic characteristics. As CuInP2S6 exhibits a ferroelectric phase with insulating properties at room temperature, the external temperature and electrical field should be required to activate the ferro-ionic conduction. Nevertheless, such external conditions inevitably facilitate stochastic ionic conduction, which completely limits the practical applications of 2D ferro-ionic materials. Herein, free-standing 2D ferroelectric heterostructure is mechanically manipulated for nano-confined conductive filaments growth in free-standing 2D ferro-ionic memristor. The ultra-high mechanical bending is selectively facilitated at the free-standing area to spatially activate the ferro-ionic conduction, which allows the deterministic local positioning of Cu+ ion transport. According to the local flexoelectric engineering, 5.76×102-fold increased maximum current is observed within vertical shear strain 720 nN, which is theoretically supported by the 3D flexoelectric simulation. In conclusion, we envision that our universal free-standing platform can provide the extendable geometric solution for ultra-efficient self-powered system and reliable neuromorphic device.

Ultrastable 3D Heterogeneous Integration via N-Heterocyclic Carbene Self-Assembled Nanolayers.

The commercialization of 3D heterogeneous integration through hybrid bonding has accelerated, and accordingly, Cu-polymer bonding has gained significant attention as a means of overcoming the limitations of conventional Cu-SiO2 hybrid bonding, offering high compatibility with other fabrication processes. Polymers offer robust bonding strength and a low dielectric constant, enabling high-speed signal transmission with high reliability, but suffer from low thermomechanical stability. Thermomechanical stability of polymers was not achieved previously because of thermal degradation and unstable anchoring. To overcome these limitations, wafer-scale Cu-polymer bonding via N-heterocyclic carbene (NHC) nanolayers was presented for 3D heterogeneous integration, affording ultrastable packing density, crystallinity, and thermal properties. NHC nanolayers were deposited on copper electrodes via electrochemical deposition, and wafer-scale 3D heterogeneous integration was achieved by adhesive bonding at 170 °C for 1 min. Ultrastable conductivity and thermomechanical properties were observed by the spatial mapping of conductivity, work function, and force-distance curves. With regard to the characterization of NHC nanolayers, low-temperature bonding, robust corrosion inhibition, enhanced electrical conductivity, back-end-of-line process compatibility, and fabrication process reduction, NHC Cu/polymer bonding provides versatile advances in 3D heterogeneous integration, indicating that NHC Cu/polymer bonding can be utilized as a platform for future 3D vertical chip architectures.

Low-Temperature Alignment of Conjugated Polymers by Plasticizer-Aided Physical Rubbing.

Rubbing-induced alignment of conjugated polymers is systematically investigated in terms of intra- and inter-molecular interaction. Various polymer films with a broad range of polymer chain rigidity are rubbed, and the degree of polymer chain alignment is quantitatively characterized. The rubbing technique effectively aligns crystalline domains in conjugated polymer films when the temperature approaches the critical rubbing temperature ( T r c $T_{\mathrm{r}}^{\mathrm{c}}$ ), at which the rearrangement and the slip of polymer chains are possible. A polymer with significant intra-/inter-molecular interactions exhibits higher T r c $T_{\mathrm{r}}^{\mathrm{c}}$ , though quantitative analysis reveals an intermediately aligned state at temperature Tr ' lower than T r c $T_{\mathrm{r}}^{\mathrm{c}}$ . This state originates from polymer chain aggregation in an amorphous domain. The intermediately aligned state can be controlled by plasticizer, which enables low-temperature alignment of high-mobility polymer film by reducing Tr ' to near 100 °C, increases the crystallinity, and improves the alignment effect at this state comparable to that of the completely aligned state obtained at extremely high temperatures.

Disordered Phase-Assisted Growth of Organic Semiconductor Crystals on Self-Assembled Monolayer Templates.

Achieving high mobility and bias stability is a challenging obstacle in the advancement of organic thin-film transistors (OTFTs). To this end, the fabrication of high-quality organic semiconductor (OSC) thin films is critical for OTFTs. Self-assembled monolayers (SAMs) have been used as growth templates for high-crystalline OSC thin films. Despite significant research progress in the growth of OSC on SAMs, a detailed understanding of the growth mechanism of the OSC thin films on a SAM template is lacking, which has limited its use. In this study, the effects of the structure (thickness and molecular packing) of SAM on the nucleation and growth behavior of the OSC thin films were investigated. We found that disordered SAM molecules assisted in the surface diffusion of the OSC molecules and resulted in a small nucleation density and large grain size of the OSC thin films. Moreover, a thick SAM with disordered SAM molecules on the top was found to be beneficial for the high mobility and bias stability of the OTFTs.

Achieving ideal transistor characteristics in conjugated polymer semiconductors.

Organic thin-film transistors (OTFTs) with ideal behavior are highly desired, because nonideal devices may overestimate the intrinsic property and yield inferior performance in applications. In reality, most polymer OTFTs reported in the literature do not exhibit ideal characteristics. Supported by a structure-property relationship study of several low-disorder conjugated polymers, here, we present an empirical selection rule for polymer candidates for textbook-like OTFTs with high reliability factors (100% for ideal transistors). The successful candidates should have low energetic disorder along their backbones and form thin films with spatially uniform energetic landscapes. We demonstrate that these requirements are satisfied in the semicrystalline polymer PffBT4T-2DT, which exhibits a reliability factor (~100%) that is exceptionally high for polymer devices, rendering it an ideal candidate for OTFT applications. Our findings broaden the selection of polymer semiconductors with textbook-like OTFT characteristics and would shed light upon the molecular design criteria for next-generation polymer semiconductors.

Effect of Providing Environmental Enrichment into Aviary House on the Welfare of Laying Hens.

This study aimed to determine the effects of providing environmental enrichment materials­pumice stone and alfalfa hay­to laying hens in the aviary system. A total of 2196 40-week-old Hy-Line Brown laying hens were randomly allotted to three treatment groups: (1) no enrichment (control; CON), (2) enrichment with pumice stone (PS), and (3) enrichment with alfalfa hay (HAY). Each treatment comprised four replicates of 183 hens each, and four of the same materials were provided per replicate. The experiment lasted for 26 weeks. Feed and water were provided ad libitum. As a result, the PS and HAY groups demonstrated increased egg production (p < 0.001). The HAY group showed a reduced rate of mislaid eggs (p < 0.01) and produced low egg weight and pale-yellow yolk (p < 0.05). Both enrichment materials decreased blood creatinine (CRE) or lactate dehydrogenase (LDH) in the blood and resulted in a significantly lower corticosterone (CORT) level (p < 0.05). However, the feather condition scores for the laying hens were similar across all treatments (p > 0.05). In summary, although pumice stone and alfalfa hay are effective in alleviating stress and improving the production of laying hens, additional environmental improvement studies are needed to contribute to reducing pecking behaviors in poultry farming.

Fluorination-Induced Charge Trapping and Operational Instability in Conjugated-Polymer Field-Effect Transistors.

Fluorination of a conjugated polymer backbone is an effective strategy to control the microstructure and electronic structure of a conjugated polymer. Although fluorination has been widely reported to increase charge carrier mobility, its effect on the operational stability of electronic devices has not been extensively investigated. Here, the effect of fluorination of a conjugated polymer backbone on charge trapping and the operational stability of organic field-effect transistors is investigated. The results show that the device based on a fluorinated conjugated polymer exhibits relatively poor operational stability despite its greater charge carrier mobility compared with that in the device based on its nonfluorinated polymer counterpart. Experimental results reveal that the low stability originates from the greater degree of shallow trapping of charge carriers within the fluorinated polymer thin film and that the shallow trapping is closely related to the presence of minority charge carriers. A mechanism of charge trapping is proposed.