Effects of treatment processes on AOC removal and changes of bacterial diversity in a water treatment plant.

The effectiveness of different treatment processes on assimilable organic carbon (AOC) removal and bacterial diversity variations was evaluated in a water treatment plant. The van der Kooij technique was applied for AOC analysis and responses of bacterial communities were characterized by the metagenomics assay. Results show that the AOC concentrations were about 93, 148, 43, 51, 37, and 38 µg acetate-C/L in effluents of raw water basin, preozonation, rapid sand filtration (RSF), ozonation, biofiltration [biological activated carbon (BAC) filtration], and chlorination (clear water), respectively. Increased AOC concentrations were observed after preozonation, ozonation, and chlorination units due to the production of biodegradable organic matters after the oxidation processes. Results indicate that the oxidation processes were the main causes of AOC formation, which resulted in significant increases in AOC concentrations (18-59% increment). The AOC removal efficiencies were 47, 28, and 60% in the RSF, biofiltration, and the whole system, respectively. RSF and biofiltration were responsible for the AOC treatment and both processes played key roles in AOC removal. Thus, both RSF and biofiltration processes would contribute to AOC treatment after oxidation. Sediments from the raw water basin and filter samples from RSF and BAC units were collected and analyzed for bacterial communities. Results from scanning electron microscope analysis indicate that bacterial colonization was observed in filter materials. This indicates that the surfaces of the filter materials were beneficial to bacterial growth and AOC removal via the adsorption and biodegradation mechanisms. Next generation sequencing analyses demonstrate that water treatment processes resulted in the changes of bacterial diversity and community profiles in filters of RSF and BAC. According to the findings of bacterial composition and interactions, the dominant bacterial phyla were Proteobacteria (41% in RSF and 56% in BAC) followed by Planctomycetes and Acidobacteria in RSF and BAC systems, which might affect the AOC biodegradation efficiency. Results would be useful in developing AOC treatment and management processes in water treatment plants.

Aerobic Biodegradation of OCDD by P. Mendocina NSYSU: Effectiveness and Gene Inducement Studies.

The goals of this study were to assess the effectiveness of (1) enhancing octachlorinated dibenzo-p-dioxin (OCDD) biodegradation under aerobic conditions by Pseudomonas mendocina NSYSU (P. Mendocina NSYSU) with the addition of lecithin, and (2) inducing OCDD ring-cleavage genes by pentachlorophenol (PCP) and OCDD addition. P. Mendocina NSYSU could biodegrade OCDD via aerobic cometabolism and lecithin was used as a primary substrate. Approximately 74 and 67% of OCDD biodegradation was observed after 60 days of incubation with lecithin and glucose supplement, respectively. Lecithin was also used as the solubilization additive resulting in OCDD solubilization and enhanced bioavailability of OCDD to P. Mendocina NSYSU. Two intradiol and extradiol ring-cleavage dioxygenase genes (Pmen_0474 and Pmen_2526) were identified from gene analyses. Gene concentration was significantly enhanced after the inducement by PCP and OCDD. Higher gene inducement efficiency was obtained using PCP as the inducer, and Pmen_2526 played a more important role in OCDD biodegradation.

Developing an Integrated Modeling Tool for River Water Quality Index Assessment.

The goal of this study was to establish a modeling tool for river water quality with a direct linkage to the water quality index (WQI5) calculation and the river water quality model, the Water Quality Analysis Simulation Program (WASP), for pollutant transport modeling. The integrated WASP and WQI5 tool was field-tested to assess pollutant loadings and their impacts on river environment. Suspended solid (SS) and electric conductivity (EC) correlation equations and the WQI5 calculation tool were included in the water quality model and direct WQI5 calculation. The SS concentration, which was influenced by river flows, had crucial effects on river water quality and WQI5 values. EC value was controlled by dissolution of soil minerals, which was affected by the watershed drainage area and surface runoff. The integrated system could establish a direct correlation for river water quality, river flow, and WQI5.

Biodegradation of Polychlorinated Dibenzo--Dioxins by Strain NSYSU.

The dioxin-degrading bacterium strain NSYSU (NSYSU strain) has been isolated from dioxin-contaminated soil by selective enrichment techniques. In the present study, the NSYSU strain was investigated for its capability to biodegrade polychlorinated dibenzo--dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) under aerobic and anaerobic conditions. High-resolution gas chromatography-mass spectrometry and a chemically activated luciferase gene expression bioassay were performed to determine the presence of dioxin compounds. The results indicate that the NSYSU strain could degrade PCDDs and PCDFs under anaerobic conditions in liquid cultures. The main intermediates of the dechlorination process were identified. The results of the bioreactor test indicate that the NSYSU strain could also degrade PCDDs and PCDFs effectively in soil slurries under aerobic conditions. Results from the bioreactor experiment show that approximately 98 and 97% of octachlorodibenzofuran and OCDD were degraded, respectively. The dioxin concentrations in soil slurry decreased from 5823 to 1198 pg toxic equivalency g, resulting in total dioxin removal of 79%. These first findings suggest that the NSYSU strain has the potential to be an effective tool for the bioremediation of soils contaminated with highly recalcitrant organic compounds.

Control of trichloroethylene plume migration using a biobarrier system: a field-scale study.

The objective of this field-scale study was to evaluate the effectiveness of controlling trichloroethylene (TCE) plume migration using the polycolloid substrate (PS) biobarrier. The developed PS (containing soybean oil, lactate and surfactants) could release substrate to enhance the TCE dechlorination. In this study, a biobarrier comprising PS injection wells was installed. Injection wells were installed at 5-m intervals, and approximately 15 L of PS was injected into each well. Results show that TCE concentrations in the injection wells dropped from an average of 87 µg/L to below 1 µg/L after 35 days of PS injection. The total organic carbon concentrations in the injection wells increased from an average of 2.1-543 mg/L after 30 days of PS injection. The dissolved oxygen (DO) concentrations and oxidation-reduction potential (ORP) values dropped from an average of 1.6 mg/L to below 0.1 mg/L and from 124 mv to -14 mv after 20 days of injection, respectively. The DO and ORP remained in anaerobic conditions during the remaining 100 days of the operational period. TCE degradation by-products were observed in groundwater samples during the operational period. This reveals that the addition of PS could effectively enhance the reductive dechlorinating of TCE.

Development of a PET/EPRI combined imaging system for assessing tumor hypoxia.

Precise quantitative delineation of tumor hypoxia is essential in radiation therapy treatment planning to improve the treatment efficacy by targeting hypoxic sub-volumes. We developed a combined imaging system of positron emission tomography (PET) and electron para-magnetic resonance imaging (EPRI) of molecular oxygen to investigate the accuracy of PET imaging in assessing tumor hypoxia. The PET/EPRI combined imaging system aims to use EPRI to precisely measure the oxygen partial pressure in tissues. This will evaluate the validity of PET hypoxic tumor imaging by (near) simultaneously acquired EPRI as ground truth. The combined imaging system was constructed by integrating a small animal PET scanner (inner ring diameter 62 mm and axial field of view 25.6 mm) and an EPRI subsystem (field strength 25 mT and resonant frequency 700 MHz). The compatibility between the PET and EPRI subsystems were tested with both phantom and animal imaging. Hypoxic imaging on a tumor mouse model using 18F-fluoromisonidazole radio-tracer was conducted with the developed PET/EPRI system. We report the development and initial imaging results obtained from the PET/EPRI combined imaging system.

Developing nonpoint-source suspended solids control strategies using multimedia watershed management modeling.

Kaoping River Basin is the largest and most intensively used river basin in Taiwan. In this study, 14 types of land-use patterns in the basin are classified with the aid of the Erdas Imagine process (Erdas, Inc., Atlanta, Georgia) and ArcView geographic information system (GIS) (ESRI, Redlands, California). Results from GIS identification and field verification indicate that orchard gardens, rice paddies, and sugarcane fields dominate the farmland areas in the basin. Investigation results indicate that nonpoint-source (NPS) pollution has significant contributions to the suspended solids load to the Kaoping River during the wet season. The average suspended solids concentrations increased from below 64 mg/ L in dry seasons to more than 1700 mg/L in wet seasons. The Integrated Watershed Management Model (Systech Engineering, Inc., San Ramon, California) was applied to simulate the water quality and evaluate the NPS suspended solids load to the river. Modeling results show that forestation and land-use management are feasible best management practices for NPS suspended solids reduction.

Preliminary identification of watershed management strategies for the Houjing river in Taiwan.

The Houjing River watershed is one of the three major river watersheds in the Kaohsiung City, Taiwan. Based on the recent water quality analysis, the Houjing River is heavily polluted. Both point and non-point source (NPS) pollutants are the major causes of the poor water quality in the Houjing River. Investigation results demonstrate that the main point pollution sources included municipal, agricultural, and industrial wastewaters. In this study, land use identification in the Houjing River watershed was performed by integrating the skills of geographic information system (GIS) and global positioning system (GPS). Results show that the major land-use patterns in the upper catchment of the Houjing River watershed were farmlands, and land-use patterns in the mid to lower catchment were residential and industrial areas. An integrated watershed management model (IWMM) and Enhanced Stream Water Quality Model (QUAL2K) were applied for the hydrology and water quality modeling, watershed management, and carrying capacity calculation. Modeling results show that the calculated NH3-N carrying capacity of the Houjing River was only 31 kg/day. Thus, more than 10,518 kg/day of NH3-N needs to be reduced to meet the proposed water quality standard (0.3 mg/L). To improve the river water quality, the following remedial strategies have been developed to minimize the impacts of NPS and point source pollution on the river water quality: (1) application of BMPs [e.g. source (fertilizer) reduction, construction of grassy buffer zone, and land use management] for NPS pollution control; (2) application of river management scenarios (e.g. construction of the intercepting and sewer systems) for point source pollution control; (3) institutional control (enforcement of the industrial wastewater discharge standards), and (4) application of on-site wastewater treatment systems for the polishment of treated wastewater for water reuse.

Using a constructed wetland for non-point source pollution control and river water quality purification: a case study in Taiwan.

The Kaoping River Rail Bridge Constructed Wetland, which was commissioned in 2004, is one of the largest constructed wetlands in Taiwan. This multi-function wetland has been designed for the purposes of non-point source (NPS) pollutant removal, wastewater treatment, wildlife habitat, recreation, and education. The major influents of this wetland came from the local drainage trench containing domestic, agricultural, and industrial wastewaters, and effluents from the wastewater treatment plant of a paper mill. Based on the quarterly investigation results from 2007 to 2009, more than 96% of total coliforms (TC), 48% of biochemical oxygen demand (BOD), and 40% of nutrients (e.g. total nitrogen, total phosphorus) were removed via the constructed wetland system. Thus, the wetland system has a significant effect on water quality improvement and is capable of removing most of the pollutants from the local drainage system before they are discharged into the downgradient water body. Other accomplishments of this constructed wetland system include the following: providing more green areas along the riversides, offering more water assessable eco-ponds and eco-gardens for the public, and rehabilitating the natural ecosystem. The Kaoping River Rail Bridge Constructed Wetland has become one of the most successful multi-function constructed wetlands in Taiwan. The experience obtained from this study will be helpful in designing similar natural treatment systems for river water quality improvement and wastewater treatment.

Constructed wetland for water quality improvement: a case study from Taiwan.

In Taiwan, more than 20% of the major rivers are mildly to heavily polluted by domestic, industrial, and agricultural wastewaters due to the low percentage of sewers connected to wastewater treatment plants. Thus, constructed or engineered wetlands have been adopted as the major alternatives to clean up polluted rivers. Constructed wetlands are also applied as the tertiary wastewater treatment systems for the wastewater polishment to meet water reuse standards with lower operational costs. The studied Kaoping River Rail Bridge Constructed Wetland (KRRBCW) is the largest constructed wetland in Taiwan. It is a multi-function wetland and is used for polluted creek water purification and secondary wastewater polishment before it is discharged into the Kaoping River. Although constructed wetlands are feasible for contaminated water treatment, wetland sediments are usually the sinks for organics and metals. In this study, water and sediment samples were collected from the major wetland basins in KRRBCW. The investigation results show that more than 97% of total coliforms (TC), 55% of biochemical oxygen demand (BOD), and 30% of nutrients [e.g. total nitrogen (TN), total phosphorus (TP)] were removed via the constructed wetland system. However, results from the sediment analyses show that wetland sediments contained high concentrations of metals (e.g. Cu, Fe, Zn, Cr, and Mn), organic contents (sediment oxygen demand = 1.7 to 7.6 g O(2)/m(2) d), and nutrients (up to 18.7 g/kg of TN and 1.22 g/kg of TN). Thus, sediments should be excavated periodically to prevent the release the pollutants into the wetland system and causing the deterioration of wetland water quality. Results of polymerase chain reaction (PCR), denaturing gradient gel electrophoresis (DGGE), and nucleotide sequence analysis reveal that a variation in microbial diversity in the wetland systems was observed. Results from the DGGE analysis indicate that all sediment samples contained significant amounts of microbial ribospecies, which might contribute to the carbon degradation and nitrogen removal. Gradual disappearance of E. coli was also observed along the flow courses through natural attenuation mechanisms.

Design, evaluation and initial imaging results of a PET insert based on strip-line readout for simultaneous PET/MRI.

We present the development of a PET insert system for potential simultaneous PET/MR imaging using a 9.4 T small animal MRI scanner to test our system. The detectors of the system adopt a strip-line based multiplexing readout method for SiPM signals. In this readout, multiple SiPM outputs in a row share a common strip-line. The position information about a hit SiPM is encoded in the propagation time difference of the signals arriving at the two ends of the strip-line. The use of strip-lines allows us to place the data acquisition electronics remotely from the detector module to greatly simplify the design of the detector module and minimize the mutual electromagnetic interference. The prototype is comprised of 14 detector modules, each of which consists of an 8x4 LYSO scintillator array (each LYSO crystal is 3x3x10 mm3) coupled to two units of Hamamatsu MPPC arrays (4x4, 3.2 mm pitch) that are mounted on a strip-line board. On the strip-line board, outputs of the 32 SiPMs are routed to 2 strip-lines so that 16 SiPM signals share a strip-line. The detector modules are installed inside a plastic cylindrical supporting structure with an inner and outer diameter of 60 mm and 115 mm, respectively, to fit inside a Bruker BioSpec 9.4 Tesla MR scanner. The axial field of view of the prototype is 25.4 mm. The strip-lines were extended by using 5-meter cables to a sampling data acquisition (DAQ) board placed outside the magnet. The detectors were not shielded in the interest of investigating how they may affect and be affected by the MRI. Experimental tests were conducted to evaluate detection performance, and phantom and animal imaging were carried out to assess the spatial resolution and the MR compatibility of the PET insert. Initial results are encouraging and demonstrate that the prototype insert PET can potentially be used for PET/MR imaging if appropriate shielding will be implemented for minimizing the mutual interference between the PET and MRI systems.

Engineered biosynthesis of a complete macrolactone in a heterologous host.

Macrocyclic polyketides have been subjects of great interest in synthetic and biosynthetic chemistry because of their structural complexity and medicinal activities. With expression of the entire 6-deoxyerythronolide B synthase (DEBS) (10,283 amino acids) in a heterologous host, substantial quantities of 6-deoxyerythronolide B (6dEB), the aglycone of the macrolide antibiotic erythromycin, and 8,8a-deoxyoleandolide, a 14-membered lactone ring identical to 6dEB except for a methyl group side chain in place of an ethyl unit, were synthesized in Streptomyces coelicolor. The biosynthetic strategy utilizes a genetic approach that facilitates rapid structural manipulation of DEBS or other modular polyketide synthases (PKSs), including those found in actinomycetes with poorly developed genetic methods. From a technological viewpoint, this approach should allow the rational design of biosynthetic products and may eventually lead to the generation of diverse polyketide libraries by means of combinatorial cloning of naturally occurring and mutant PKS modules.

Application of surfactant enhanced permanganate oxidation and bidegradation of trichloroethylene in groundwater.

The industrial solvent trichloroethylene (TCE) is among the most ubiquitous chlorinated solvents found in groundwater contamination. The main objectives of this study were to evaluate the feasibility of using non-ionic surfactant Simple Green (SG) to enhance the oxidative dechlorination of TCE by potassium permanganate (KMnO4) employing a continuous stir batch reactor system (CSBR) and column experiments. The effect of using surfactant SG to enhance the biodegradation of TCE via aerobic cometabolism was also examined. Results from CSBR experiments revealed that combination of KMnO4 with surfactant SG significantly enhanced contaminant removal, particularly when the surfactant SG concentrated at its CMC. TCE degradation rates ranged from 74.1% to 85.7% without addition of surfactant SG while TCE degradation rates increased to ranging from 83.8% to 96.3% with presence of 0.1wt% SG. Furthermore, results from column experiments showed that TCE was degraded from 38.1microM to 6.2microM in equivalent to 83.7% of TCE oxidation during first 560min reaction. This study has also demonstrated that the addition of surfactant SG is a feasible method to enhance bioremediation efficiency for TCE contaminated groundwater. The complete TCE degradation was detected after 75 days of incubation with both 0.01 and 0.1wt% of surfactant SG addition. Results revealed that surfactant enhanced chemical oxidation and bioremediation technology is one of feasible approaches to clean up TCE contaminated groundwater.

Methyl tert-butyl ether (MTBE) degradation by ferrous ion-activated persulfate oxidation: feasibility and kinetics studies.

The objective of this study was to evaluate the feasibility of using ferrous ion-activated persulfate oxidation to remediate groundwater contaminated with methyl tert-butyl ether (MTBE). In this study, batch experiments were conducted to evaluate the effects of various factors on the efficiency of MTBE degradation including persulfate concentrations, ferrous ion concentrations, and persulfate coupled with hydrogen peroxide. Results show that ferrous ion-activated persulfate oxidation was capable of degrading MTBE efficiently. Persulfate and ferrous ion concentrations correlated with MTBE degradation rates. However, excess addition of ferrous ion resulted in decreased MTBE degrading rates most likely because of competition for sulfate free radicals between ferrous ion and MTBE. Two main byproducts of MTBE degradation, tert-butyl formate and tert-butyl alcohol, were detected in the experiments; both were, however, subsequently degraded. Results of sulfate analysis show that proper addition of ferrous ion could prevent unnecessary persulfate decomposition.

Evaluation of biological stability and corrosion potential in drinking water distribution systems: a case study.

The appearance of assimilable organic carbon (AOC), microbial regrowth, disinfection by-products (DBPs), and pipe corrosion in drinking water distribution systems are among those major safe drinking water issues in many countries. The water distribution system of Cheng-Ching Lake Water Treatment Plant (CCLWTP) was selected in this study to evaluate the: (1) fate and transport of AOC, DBPs [e.g., trihalomethanes (THMs), haloacetic acids (HAAs)], and other organic carbon indicators in the selected distribution system, (2) correlations between AOC (or DBPs) and major water quality parameters [e.g. dissolved oxygen (DO), free residual chlorine, and bacteria, and (3) causes and significance of corrosion problems of the water pipes in this system. In this study, seasonal water samples were collected from 13 representative locations in the distribution system for analyses of AOC, DBPs, and other water quality indicators. Results indicate that residual free chlorine concentrations in the distribution system met the drinking water standards (0.2 to 1 mg l(-1)) established by Taiwan Environmental Protection Administration (TEPA). Results show that AOC measurements correlated positively with total organic carbon (TOC) and UV-254 (an organic indicator) values in this system. Moreover, AOC concentrations at some locations were higher than the 50 microg acetate-C l(-1) standard established by Taiwan Water Company. This indicates that the microbial regrowth might be a potential water quality problem in this system. Higher DO measurements (>5.7 mg l(-1)) might cause the aerobic biodegradation of THMs and HAAs in the system, and thus, low THMs (<0.035 mg l(-1)) and HAAs (<0.019 mg l(-1)) concentrations were observed at all sampling locations. Results from the observed negative Langelier Saturation Index (LSI) values, higher Ryznar Stability Index (RSI) values, and high Fe3+ concentrations at some pipe-end locations indicate that highly oxidative and corrosive conditions occurred. This reveals that pipe replacement should be considered at these locations. These findings would be helpful in managing the water distribution system for maintaining a safe drinking water quality.

Application of integrated GIS and multimedia modeling on NPS pollution evaluation.

In Taiwan, nonpoint source (NPS) pollution is one of the major causes of the impairment of surface waters. I-Liao Creek, located in southern Taiwan, flows approximately 90 km and drains toward the Kaoping River. Field investigation results indicate that NPS pollution from agricultural activities is one of the main water pollution sources in the I-Liao Creek Basin. Assessing the potential of NPS pollution to assist in the planning of best management practice (BMP) is significant for improving pollution prevention and control in the I-Liao Creek Basin. In this study, land use identification in the I-Liao Creek Basin was performed by properly integrating the skills of geographic information system (GIS) and global positioning system (GPS). In this analysis, 35 types of land use patterns in the watershed area of the basin are classified with the aid of Erdas Imagine process system and ArcView GIS system. Results indicate that betel palm farms, orchard farms, and tea gardens dominate the farmland areas in the basin, and are scattered around on both sides of the river corridor. An integrated watershed management model (IWMM) was applied for simulating the water quality and evaluating NPS pollutant loads to the I-Liao Creek. The model was calibrated and verified with collected water quality and soil data, and was used to investigate potential NPS pollution management plans. Simulated results indicate that NPS pollution has significant contributions to the nutrient loads to the I-Liao Creek during the wet season. Results also reveal that NPS pollution plays an important role in the deterioration of downstream water quality and caused significant increase in nutrient loads into the basin's water bodies. Simulated results show that source control, land use management, and grassy buffer strip are applicable and feasible BMPs for NPS nutrient loads reduction. GIS system is an important method for land use identification and waste load estimation in the basin. Linking the information of land utilization with the NPS pollution simulation model may further provide essential information of potential NPS pollution for all subregions in the river basin. Results and experience obtained from this study will be helpful in designing the watershed management and NPS pollution control strategies for other similar river basins.

Application of γ-PGA as the primary carbon source to bioremediate a TCE-polluted aquifer: A pilot-scale study.

The effectiveness of using gamma poly-glutamic acid (γ-PGA) as the primary carbon and nitrogen sources to bioremediate trichloroethene (TCE)-contaminated groundwater was studied in this pilot-scale study. γ-PGA (40 L) solution was injected into the aquifer via the injection well (IW) for substrate supplement. Groundwater samples were collected from monitor wells and IW and analyzed for TCE and its byproducts, geochemical indicators, dechlorinating bacteria, and microbial diversity periodically. Injected γ-PGA resulted in an increase in total organic carbon (TOC) (up to 9820 mg/L in IW), and the TOC biodegradation caused the formation of anaerobic conditions. Increased ammonia concentration (because of amine release from γ-PGA) resulted in the neutral condition in groundwater, which benefited the growth of Dehalococcoides. The negative zeta potential and micro-scale diameter of γ-PGA allowed its globule to distribute evenly within soil pores. Up to 93% of TCE removal was observed (TCE dropped from 0.14 to 0.01 mg/L) after 59 days of γ-PGA injection, and TCE dechlorination byproducts were also biodegraded subsequently. Next generation sequence (NGS) analyses were applied to determine the dominant bacterial communities. γ-PGA supplement developed reductive dechlorinating conditions and caused variations in microbial diversity and dominant bacterial species. The dominant four groups of bacterial communities including dechlorinating bacteria, vinyl chloride degrading bacteria, hydrogen producing bacteria, and carbon biodegrading bacteria.

Application of an emulsified polycolloid substrate biobarrier to remediate petroleum-hydrocarbon contaminated groundwater.

Emulsified polycolloid substrate (EPS) was developed and applied in situ to form a biobarrier for the containment and enhanced bioremediation of a petroleum-hydrocarbon plume. EPS had a negative zeta potential (-35.7 mv), which promoted its even distribution after injection. Batch and column experiments were performed to evaluate the effectiveness of EPS on toluene containment and biodegradation. The EPS-to-water partition coefficient for toluene (target compound) was 943. Thus, toluene had a significant sorption affinity to EPS, which caused reduced toluene concentration in water phase in the EPS/water system. Groundwater containing toluene (18 mg/L) was pumped into the three-column system at a flow rate of 0.28 mL/min, while EPS was injected into the second column to form a biobarrier. A significant reduction of toluene concentration to 0.1 mg/L was observed immediately after EPS injection. This indicates that EPS could effectively contain toluene plume and prevent its further migration to farther downgradient zone. Approximately 99% of toluene was removed after 296 PVs of operation via sorption, natural attenuation, and EPS-enhanced biodegradation. Increase in total organic carbon and bacteria were also observed after EPS supplement. Supplement of EPS resulted in a growth of petroleum-hydrocarbon degrading bacteria, which enhanced the toluene biodegradation.

Emulsified polycolloid substrate biobarrier for benzene and petroleum-hydrocarbon plume containment and migration control - A field-scale study.

The objective of this field-scale study was to assess the effectiveness of applying an emulsified polycolloid substrate (EPS; containing cane molasses, soybean oil, and surfactants) biobarrier in the control and remediation of a petroleum-hydrocarbon plume in natural waters. An abandoned petrochemical manufacturing facility site was contaminated by benzene and other petroleum products due to a leakage from a storage tank. Because benzene is a petroleum hydrocarbon with a high migration ability, it was used as the target compound in the field-scale study. Batch partition and sorption experiment results indicated that the EPS to water partition coefficient for benzene was 232 mg/mg at 25 °C. This suggests that benzene had a higher sorption affinity to EPS, which decreased the benzene concentrations in groundwater. The EPS solution was pressure-injected into three remediation wells (RWs; 150 L EPS in 800 L groundwater). Groundwater samples were collected from an upgradient background well, two downgradient monitor wells (MWs), and the three RWs for analyses. EPS injection increased total organic carbon (TOC) concentrations (up to 786 mg/L) in groundwater, which also resulted in the formation of anaerobic conditions. An abrupt drop in benzene concentration (from 6.9 to below 0.04 mg/L) was observed after EPS supplementation in the RWs due to both sorption and biodegradation mechanisms. Results show that the EPS supplement increased total viable bacteria and enhanced bioremediation efficiency, which accounted for the observed decrease in benzene concentration. The first-order decay rate in RW1 increased from 0.003 to 0.023 d-1 after EPS application. Injection of EPS resulted in significant growth of indigenous bacteria, and 23 petroleum-hydrocarbon-degrading bacterial species were detected, which enhanced the in situ benzene biodegradation efficiency. Results demonstrate that the EPS biobarrier can effectively contain a petroleum-hydrocarbon plume and prevent its migration to downgradient areas, which reduces the immediate risk presented to downgradient receptors.

Spontaneous amplification of the actinorhodin gene cluster in Streptomyces coelicolor involving native insertion sequence IS466.

We observed a spontaneous amplification of the Streptomyces coelicolor chromosome, including genes encoding biosynthetic enzymes of the antibiotic actinorhodin. A new junction of two tandem segments has, inserted within it, a third copy of a transposable element existing in two places elsewhere in the chromosome, suggesting its involvement in the amplification mechanism.