Magnetic resonance spectroscopy of the breast at 3T: pre- and post-contrast evaluation for breast lesion characterization.

PURPOSE: To determine whether in vivo proton magnetic resonance spectroscopy at 3T can provide accurate breast lesion characterization, and to determine the effect of gadolinium on the resonance of tCho. METHODS: Twenty-four positive-mammogram patients were examined on a 3T MR scanner. 1H-MRS was performed before and after gadolinium administration. tCho peak was qualitatively evaluated before and after contrast injection. RESULTS: Fourteen out of 27 lesions proved to be malignant after histopathological diagnosis. Using 1H-MRS, before contrast injection, 6/14 confirmed malignancies and 11/13 benign lesions were correctly classified; while, after contrast injection, 11/14 confirmed malignancies and 12/13 benign processes were correctly classified. Post gadolinium 1H-MRS proved useful in picking up tCho signal, improving the overall accuracy, sensitivity, and specificity by 35%, 83%, and 9%, respectively. CONCLUSION: 1H-MRS overall accuracy, sensitivity, and specificity in detecting breast lesion's malignancy were increased after gadolinium administration. It is prudent to perform 1H-MRS before contrast injection in large breast lesions to avoid choline underestimation. In cases of small or non-mass lesions, it is recommended to perform 1H-MRS after contrast injection for better voxel prescription to enable a reliable preoperative diagnosis.

Spectroscopic evaluation of glioma grading at 3T: the combined role of short and long TE.

PURPOSE: To evaluate the diagnostic value of 3T (1)H-MRS in grading cerebral gliomas using short and long echo times. METHODS: 1H-MRS was performed on 71 patients with untreated cerebral gliomas. Metabolite ratios of NAA/Cr, Cho/Cr, Cho/NAA, and mI/Cr were calculated for short and long TE and compared between low and high grade gliomas. Lipids were qualitatively evaluated. ROC analysis was performed to obtain the cut-off values for the metabolic ratios presenting statistical difference between the two glioma grades. RESULTS: Intratumoral Cho/Cr at both TEs and long TE Cho/NAA were significantly different between low and high grade gliomas. Peritumoral NAA/Cr of both TEs, as well as long TE Cho/Cr and Cho/NAA ratios, significantly differentiated the two tumor grades. Diagnostic sensitivity of peritumoral short TE NAA/Cr proved to be superior over the other metabolic ratios, whereas intratumoral short TE Cho/Cr reached the highest levels of specificity and accuracy. Overall, short TE 1H-MRS reached higher total sensitivity in predicting glioma grade, over long TE. CONCLUSION: An advantage was found in using short TE over long TE 1H-MRS in the discrimination of low versus high grade gliomas. Moreover, the results suggested that the peritumoral area of gliomas may be more valuable in predicting glioma grade than using only the intratumoral area.

A modification of flattening filter free linac for IMRT.

PURPOSE: This study investigates the benefits of a modified flattening filter free (FFF) linac over the standard (STD) linac equipped with the flattening filter. Energy and angular spread of the electron beam of the FFF linac were modified. Modification of FFF beam parameters is explored to maximize the monitor unit efficiency and to minimize the head scatter in IMRT delivery for large target volumes or targets lying away from the central axis. METHODS: The EGSnrc code is used to model FFF and STD linacs and study basic beam properties for both linac types in various beam configurations. Increasing energy of FFF linac results in similar beam attenuation properties and maximized dose rate compared to STD linac. Matching beam attenuation properties allows a more direct exploration of beam flatness of FFF linac in regard to IMRT delivery, especially away from the central axis where the effective dose rate is considerably smaller than the one at the central axis. Flatness of open beam dose profile of FFF linac is improved by increasing the angular spread of the electron beam. The resulting dose rate within the treatment field and outside of the field (peripheral dose) are characterized and compared to the unmodified FFF and STD linacs, RESULTS: In order to match beam penetration properties, the energy of FFF is adjusted from 6.5 to 8.0 MeV for small to medium field sizes and from 6.5 to 8.5 MeV for larger ones. Dose rate of FFF vs STD linac increased by a factor of 1.9 (6.5 MeV) and 3.4-4.1 (8.0-8.5 MeV). Adjusting the mean angular spread of the electron beam from 0 degrees to 5 degrees-10 degrees resulted in complete flattening of photon beam for field sizes between 10 x 10 cm2 and 15 x 15 cm2 and partial flattening for field sizes from 15 x 15 cm2 to 30 x 30 cm2. Values of angular spread > or =14 degrees are not recommended as they exceed the opening of the primary collimator, affecting the area at the edges of the field. FFF fields of sizes smaller than 6 x 6 cm2 are already flat and beam flattening is not necessary. Overall, the angular spread of 5 degrees-10 degrees is sufficient and can satisfactorily flatten open beam dose profiles even for larger field sizes. Increasing the electron beam angular spread amounts to a slight decrease of dose rate of FFF linac. However, for angular spread, 5 degrees-10 degrees dose rate factor of FFF vs STD is still about 1.6-2.6, depending on the field size (and the adjusted energy). Similarly, in case of peripheral dose, a moderate increase in dose can be observed for angular spread of 5 degrees-10 degrees and for field sizes 10 x 10 cm2 to 30 x 30 cm2. Lastly, beam flatness of not modified FFF linac can be conveniently described by an analytical function representing a ratio of STD vs FFF doses: 1 + b|r|(n). CONCLUSIONS: A modified FFF beamline with increased energy and electron beam angular spread results in satisfactory flattened beam and high dose rate within the field. Peripheral dose remaining at similar (or smaller) level than that of STD linac for the same delivered dose within the treatment field.

EXTREMELY LOW FREQUENCY ELECTROMAGNETIC EXPOSURE ASSESSMENT IN SCHOOLS: A STATISTICAL ANALYSIS OF URBAN AND SEMI-URBAN AREAS.

The aim of this research paper is to estimate the mean value of extremely low frequency (ELF) exposure in schools in Greece. Detailed ELF measurements were conducted and analyzed by the Weighted Peak Method (WPM), which estimates the overall contribution of electromagnetic waves from 1 Hz to 400 kHz, including their phases. A sample of 243 schools was sampled to calculate. The mean value of ELF magnetic fields (MFs) measured in these two groups comprising 243 schools was the principal focus of interest. ELF MF measurements taken in schools situated both far from and near ELF sources had mean and maximum values well below the current International Commission on Non-Ionizing Radiation Protection (ICNIRP) standard. The mean value of ELF MFs from all sources within the sampled schools in Greece was 0.21 µΤ. A statically significant difference between the mean MFs measured in the two groups of schools was found, but the MFs in both groups were much lower than the ICNIRP standard.

Urethrographic examinations: Patient and staff exposures and associated radiobiological risks.

Medical exposure of the general population due to radiological investigations is the foremost source of all artificial ionising radiation. Here, we focus on a particular diagnostic radiological procedure, as only limited data are published with regard to radiation measurements during urethrograpic imaging. Specifically, this work seeks to estimate patient and occupational effective doses during urethrographic procedures at three radiology hospitals. Both staff and patient X-ray exposure levels were calculated in terms of entrance surface air kerma (ESAK), obtained by means of lithium fluoride thermoluminescent dosimeters (TLD-100(LiF:Mg:Cu.P)) for 243 urethrographic examinations. Patient radiation effective doses per procedure were estimated using conversion factors obtained from the use of Public Health England computer software. In units of mGy, the median and range of ESAK per examination were found to be 10.8 (3.6-26.2), 7.0 (0.2-32.3), and 24.3 (9.0-32.0) in Hospitals A, B, and C, respectively. The overall mean and range of staff doses (in µGy) were found to be 310 (4.0-1750) per procedure. With the exception of hospital C, the present evaluations of radiation dose have been found to be similar to those of previously published research. The wide range of patient and staff doses illustrate the need for radiation dose optimisation.

Occupational exposure and radiobiological risk from thyroid radioiodine therapy in Saudi Arabia.

Worldwide, thyroid cancer accounts for some 10% of total cancer incidence, most markedly for females. Thyroid cancer radiotherapy, typically using 131I (T1/2 8.02 days; ß- max energy 606 keV, branching ratio 89.9%), is widely adopted as an adjunct to surgery or to treat inoperable cancer and hyperthyroidism. With staff potentially receiving significant doses during source preparation and administration, radiation protection and safety assessment are required in ensuring practice complies with international guidelines. The present study, concerning a total of 206 patient radioiodine therapies carried out at King Faisal Specialist Hospital and Research Center over a 6-month period, seeks to evaluate patient and occupational exposures during hospitalization, measuring ambient doses and estimating radiation risk. Using calibrated survey meters, patient exposure dose-rate estimates were obtained at a distance of 30-, 100- and 300 cm from the neck region of each patient. Occupational and ambient doses were measured using calibrated thermoluminescent dosimeters. The mean and range of administered activity (AA, in MBq) for the thyroid cancer and hyperthyroidism treatment groups were 4244 ± 2021 (1669-8066), 1507.9 ± 324.1 (977.9-1836.9), respectively. The mean annual occupational doses were 1.2 mSv, that for ambient doses outside of the isolation room corridors were found to be 0.2 mSv, while ambient doses at the nursing station were below the lower limit of detection. Exposures to staff from patients being treated for thyroid cancer were less compared to hyperthyroidism patients. With a well-defined protocol, also complying with international safety requirements, occupational exposures were found to be relatively high, greater than most reported in previous studies.

Radiation dose to patients and staff during angiography of the lower limbs. Derivation of local dose reference levels.

BACKGROUND: The Euratom directive 97/43 recommends the use of patient dose surveys in diagnostic radiology and the establishment of reference dose levels (DRLs). PURPOSE: To perform measurements of the dose delivered during diagnostic angiography of the lower limbs using thermoluminescence dosimeters (TLDs), extraction of DRLs and estimation of the effective dose and radiation risk for this particular examination. METHODS: Dose measurement was performed on 30 patients by using TLD sachets attached in 5 different positions not only on the patient, but also to the radiologist. All the appropriate factors were recorded. Measurement of the ESD was performed after each examination. RESULTS: The mean entrance skin dose (ESD) was calculated to be 70.8, 67.7, 24.3, 18.4, 9.7 mGy at the level of aorta bifurcation, pelvis, femur, knees, and at feet, respectively. The average effective dose is 9.8 mSv with the radiation risks for fatal cancer to be 5.4 x 10(-4). The effective dose of the radiologist was calculated to be 0.023 mSv per procedure. CONCLUSION: Radiation dose variation depends on the physical characteristics of the patient, on the procedure preferences by radiologists and the difficulties in conducting procedures. The main reason for the increased patient dose, compared to other studies, is the number of frames rather than the duration of fluoroscopy. For DSA of the lower limbs, the DRL was chosen to be an entrance skin dose of 96.4 mGy in the pelvic region. The dose to the radiologist is negligible.

PET Counting Response Variability Depending on Tumor Location, Activity, and Patient Obesity: A Feasibility Study of Solitary Pulmonary Nodule Using Monte Carlo.

We aim to investigate the counting response variations of positron emission tomography (PET) scanners with different detector configurations in the presence of solitary pulmonary nodule (SPN). Using experimentally validated Monte Carlo simulations, the counting performance of four different scanner models with varying tumor activity, location, and patient obesity is represented using a noise equivalent count rate (NECR). NECR is a well-established quantitative metric which has positive correlation with clinically perceived image quality. The combined effect of tumor displacement and increased activity shows a linear ascending trend for NECR with slope ranges of (12.5-18.2)*10-3 (kBq/cm3)-1 for three-ring (3R) scanners and (15.3-21.5)*10-3 (kBq/cm3)-1 for four-ring (4R). The trend for the combined effect of tumor displacement and patient obesity is exponential decay with 3R configurations weakly dependent on the patient obesity if the tumor is located at the center of the field of view with exponent's range of (6.6-33.8)*10-2cm-1. The dependence is stronger for 4R scanners (9.6-38.5)*10-2cm-1. The analysis indicates that quantitative PET data from the same SPN patient possibly examined in different time points (e.g., during staging or for the evaluation of treatment response) are affected by the different detector configurations and need to be normalized with patient weight, activity, and tumor location to reduce unwanted bias of the diagnosis. This paper provides also with a proof of concept for the ability of properly tuned simulations to provide additional insights into the counting response variability especially in tumor types where often borderline decisions have to be made regarding their characterization.

Imaging biomarker analysis of advanced multiparametric MRI for glioma grading.

AIMS AND OBJECTIVES: To investigate the value of advanced multiparametric MR imaging biomarker analysis based on radiomic features and machine learning classification, in the non-invasive evaluation of tumor heterogeneity towards the differentiation of Low Grade vs. High Grade Gliomas. METHODS AND MATERIALS: Forty histologically confirmed glioma patients (20 LGG and 20 HGG) who underwent a standard 3T-MRI tumor protocol with conventional (T1 pre/post-contrast, T2-FSE, T2-FLAIR) and advanced techniques (Diffusion Tensor and Perfusion Imaging, 1H-MR Spectroscopy), were included. A semi-automated segmentation technique, based on T1W-C and DTI, was used for tumor core delineation in all available parametric maps. 3D Texture analysis considered 12 Histogram, 11 Co-Occurrence Matrix (GLCM) and 5 Run Length Matrix (GLRLM) features, derived from p, q, MD, FA, T1W-C, T2W-FSE, T2W-FLAIR and raw DSCE data. Along with 1H-MRS metabolic ratios and mean rCBV values, a total of 581 attributes for each subject were obtained. A Support Vector Machine - Recursive Feature Elimination (SVM-RFE) algorithm and SVM classifier were utilized for feature selection and classification, respectively. RESULTS: Three different SVM classifiers were evaluated with consecutively SVM-RFE feature subsets. Linear SMO classifier demonstrated the highest performance for determining the optimal feature subset. Finally, 21 SVM-RFE top-ranked features were adopted, for training and testing the SMO classifier with leave-one-out cross-validation, achieving 95.5% Accuracy, 95% Sensitivity, 96% Specificity and 95.5% Area Under ROC Curve. CONCLUSION: Results demonstrate that quantitative analysis of phenotypic characteristics, based on advanced multiparametric MR neuroimaging data and texture features, utilizing state-of-the-art radiomic analysis methods, can significantly contribute to the pre-treatment glioma grade differentiation.

Radiation dose optimisation and risk estimation to patients and staff during hysterosalpingography.

Hysterosalpingography (HSG) is an efficient radiological examination for the evaluation of the female reproductive tract. However, it involves unavoidable irradiation to the ovaries of women in childbearing age. Therefore, radiation dose optimisation is required in order to reduce the probability of the associated risks. This study attempts to: measure patient and staff doses, estimate the effective dose and radiation risk for HSG using digital fluoroscopic images. Thirty-seven patients with infertility were examined using two digital X-ray machines. Thermoluminescence dosimeters (TLD) were used to measure entrance surface dose (ESD) for patients and staff during the procedure. The mean ESD and thyroid surface dose of the patient were 3.60 and 0.17 mGy, respectively, while the mean ESD for the staff was 0.18 mGy per procedure. The patient overall risk for cancer and hereditary effects is 24 x 10(-6), while the risk for the staff is negligible. HSG with fluoroscopic technique demonstrate improved dose characteristics, compared to the conventional radiographic-based technique, reducing the surface dose by a factor of 3, without compromising the diagnostic findings.

Estimation of effective dose and radiation risk in pediatric barium studies procedures.

The objectives of this study are to assess pediatric radiation exposure in certain barium studies and to quantify the organ and effective doses and radiation risk resultant from patients' irradiation. A total of 69 pediatric barium studies for upper and lower gastrointestinal tract. Patients' radiation dose was quantified in terms of Entrance surface air kerma (ESAKs) using exposure parameters and DosCal software. Organ and effective doses (E) were extrapolated using national Radiological Protection Board software (NRPB-R279). The mean ± (SD) and the range of patient doses per procedure were 3.7 ± 0.4 (1.0-13.0)mGy, 7.4 ± 1.7(5.5-8.0)mGy and 1.4 ± 0.9 (0.5-3.6)mGy for barium meal, swallow and enema, respectively. The mean effective doses were 0.3 ± 0.03 (0.08-1.1)mSv, 0.2 ± 1.6 (0.44-0.7)mSv and 0.3 ± 0.9 (0.1-0.8)mSv at the same order. The radiation dose were higher compared to previous studies. Therefore, pediatrics are exposed to avoidable radiation exposure. Certain optimization measures are recommended along with establishing national diagnostic reference level (DRL) to reduce the radiation risk.

Occupational exposure to electromagnetic fields. The situation in Greece.

PURPOSE: The management of the occupational exposure to electromagnetic fields (EMF), an Occupational Health and Safety (OHS) issue of great scientific, social and economic significance, was under intense negotiations at European level over the last twenty years; the Directive 2013/35/EU is the new legislative tool. The presented study deals with the practical aspects of the Directive's implementation. METHODS: The appropriate, extensive measurements and the overall EMF exposure assessments (i.e. exposure mapping, identification of hot spots, proposition of solutions) were conducted in specific workplaces, including power production, railway, broadcasting, clinical Magnetic Resonance Imaging (MRI) systems, industrial and research sites, as well as common office workplaces. RESULTS: The vast majority of the performed EMF assessments did not reveal occupational overexposures; moreover in most of the cases, even the general public exposure limits (in the above occupational areas) were not exceeded. The very few localized overexposures detected, were manageable on the basis of the technical and organizational OHS principles. On the contrary, the maintenance procedures of the EMF emitting equipment, as recorded in this survey, presented overexposures revealing a challenging field. CONCLUSIONS: This study lays a firm basis for the clarification of the occupational EMF environment, where potential exposures might be high. The proper risk assessment demands precise exposure identification and deep understanding of the EMF nature and hazards. Misconceptions range from the common exposure overestimation to the rarer case of the maintenance hazards underestimation, while attention is needed concerning the proper application of the complex limiting system of the Directive.

Assessing the difference between planned and delivered intensity-modulated radiotherapy dose distributions based on radiobiological measures.

AIMS: Because of the highly conformal distributions that can be obtained with intensity-modulated radiotherapy (IMRT), any discrepancy between the intended and delivered distributions would probably affect the clinical outcome. Consequently, there is a need for a measure that would quantify those differences in terms of a change in the expected clinical outcome. MATERIALS AND METHODS: To evaluate such a measure, cancer of the cervix was used, where the bladder and rectum are proximal and partially overlapping with the internal target volume. A solid phantom simulating the pelvic anatomy was fabricated and a treatment plan was developed to deliver the prescribed dose to the phantom. The phantom was then irradiated with films positioned in several transverse planes. The racetrack microtron at 50 MV was used in the treatment planning and delivery processes. The dose distribution delivered was analysed based on the film measurements and compared against the treatment plan. The differences in the measurements were evaluated using both physical and biological criteria. Whereas the physical comparison of dose distributions can assess the geometric accuracy of delivery, it does not reflect the clinical effect of any measured dose discrepancies. RESULTS: It is shown how small inaccuracies in delivered dose can affect the treatment outcome in terms of complication-free tumour cure. CONCLUSIONS: With highly conformal IMRT, the accuracy of the patient set-up and treatment delivery are critical for the success of the treatment. A method is proposed to evaluate the precision of the delivered plan based on changes in complication and control rates as they relate to uncertainties in dose delivery.

Artificial Optical Radiation photobiological hazards in arc welding.

Occupational Health and Safety (OHS) is associated with crucial social, economic, cultural and technical issues. A highly specialized OHS sector deals with the photobiological hazards from artificial optical radiation (AOR), which is divided into visible light, UV and IR emitted during various activities and which is legally covered by European Directive 2006/25/EC. Among the enormous amount of sources emitting AOR, the most important non-coherent ones to consider for health effects to the whole optical range, are arcs created during metal welding. This survey presents the effort to assess the complicated exposure limits of the Directive in the controlled environment of a welding laboratory. Sensors covering the UV and blue light range were set to measure typical welding procedures reproduced in the laboratory. Initial results, apart from apparently justifying the use of Personal Protective Equipment (PPE) due to even subsecond overexposures measured, also set the basis to evaluate PPE's properties and support an integrated risk assessment of the complex welding environment. These results can also improve workers' and employer's information and training about radiation hazards, which is a crucial OHS demand.

Occupational Electromagnetic Fields exposure in Magnetic Resonance Imaging systems - Preliminary results for the RF harmonic content.

PURPOSE: European legislation concerning the protection of workers from exposure to Electromagnetic Fields (EMF) was recently (26.6.2013) completed by Directive 2013/35/ΕU. This Directive is a specific one of the framework Directive 89/391/EEC and part of the overall legislation for Occupational Health and Safety (OHS). Magnetic Resonance Imaging (MRI) systems have played a key role, both in the postponement of the former 2004/40 EMF Directive and in the formation of the latest limits adopted by the new Directive. On the other hand, MRI systems are associated with the exposure of personnel to EMF of various frequencies and modulations, arousing peculiar safety issues. Therefore, we will try to acquire the highly important knowledge of the exact occupational exposure levels, in all working scenarios and practices. METHODS: Different MRI systems (1.5 and 3 T) have been chosen for a variety of measurements in order to assess occupational exposure compared to the limits (ALs) of the Directive and to the main OHS principles. Gradient function of MRI systems results in low frequency exposure, while high frequency exposure comes from the application of the RF excitation frequency. RESULTS: In most of the cases the RMS and peak value measurements do not exceed the corresponding ALs, apart from a few specific hot spots, manageable through OHS principles. DISCUSSION: Complete occupational exposure results can form the basis for dealing with multiple exposures present in MRI systems. Peculiar RF harmonic components, of no safety concern, were detected. Their origin is under examination.

Quality control of inhomogeneity correction algorithms used in treatment planning systems.

PURPOSE: This quality control program has been carried out under the auspices of S.F.P.H. (Socíete Francaise des Physiciens d'Hôpital), to evaluate the performances of radiotherapy treatment planning systems (RTPS) used by different institutions. The aim of this Quality Assurance Programme was: (a) to set up a methodology to assess globally the capability of a given system to perform inhomogeneity corrections in the irradiated medium with external photon beams; (b) to analyze the limitations of the algorithms presently used and especially the two-dimensional (2D) dose calculation possibilities; (c) to check, on a number of systems in clinical use, the validity of the method and the variation of the results as compared to measurements used as reference. METHODS AND MATERIALS: Phantom (lung equivalent material placed into polystyrene) measurements, using cobalt-60 radiation, were carried out by the authors. The phantoms were circulated among the participating institutes to be scanned, and used as input to the treatment planning computer. RESULTS: Ten systems were tested in this study, using seven different inhomogeneity correction algorithms implemented in nine different TPS; four of these algorithms are used in a pixel by pixel basis and five of them in a contour basis. Significant discrepancies or inconsistencies have been observed even for sophisticated models supposed to be mostly accurate. CONCLUSION: The proposed tests and the experimental data provided are very useful as part of a quality-control program. They should be included in the initial extensive validation of TPS before starting clinical use, and should be repeated at regular intervals and at each updating of the program. They have the merit of including the whole procedure, from patient data acquisition to dose distribution printout.

A new non-invasive and relocatable immobilization frame for fractionated stereotactic radiotherapy.

PURPOSE: A newly developed non-invasive immobilization frame for stereotactic radiotherapy is presented, which is intended to be used for both imaging (computed tomography (CT) and angiography) and radiotherapeutic procedures. MATERIALS AND METHODS: The frame is made of duraluminium so as to be stable and light and it has an elliptical shape. The immobilization is achieved using three stable locations on the patient's head, i.e. the upper dentition, the nose and the back of the neck. The fixation on the three locations ensures complete immobilization in all directions. RESULTS: The immobilization frame can be fitted as many times as is needed to most heads. In order to assess the accuracy of relocation, repeated fittings on two volunteers and on 22 patients undergoing stereotactic treatment were performed (more than 200 mountings in total), which showed maximum anterior-posterior, inferior-superior and lateral reproducibility in positioning of less than 1 mm in all cases. CONCLUSIONS AND DISCUSSION: The in-house-constructed stereotactic frame is simple to use, easily made, non-invasive, relocatable and well tolerated by the patients, providing the possibility of multiple fractions. The major advantage of using such a non-invasive stereotactic frame is the flexibility in timing the different diagnostic procedures (CT and angiography) as well as providing the possibility to extend the use to large brain lesions (treatment without an additional collimator) where a high precision is also required. It also offers significant labour and cost saving over the invasive frames and the majority of the non-invasive frames. To date, 22 patients with ages varying between 12 and 70 years have been treated using this method.

A simple method for 3D lesion reconstruction from two projected angiographic images: implementation to a stereotactic radiotherapy treatment planning system.

INTRODUCTION: The most used imaging modality for diagnosis and localisation of arteriovenous malformations (AVMs) treated with stereotactic radiotherapy is angiography. The fact that the angiographic images are projected images imposes the need of the 3D reconstruction of the lesion. This, together with the 3D head anatomy from CT images could provide all the necessary information for stereotactic treatment planning. We have developed a method to combine the complementary information provided by angiography and 2D computerized tomography, matching the reconstructed AVM structure with the reconstructed head of the patient. MATERIALS AND METHODS: The ISIS treatment planning system, developed at Institute Curie, has been used for image acquisition, stereotactic localisation and 3D visualisation. A series of CT slices are introduced in the system as well as two orthogonal angiographic projected images of the lesion. A simple computer program has been developed for the 3D reconstruction of the lesion and for the superposition of the target contour on the CT slices of the head. RESULTS AND CONCLUSIONS: In our approach we consider that the reconstruction can be made if the AVM is approximated with a number of adjacent ellipses. We assessed the method comparing the values of the reconstructed and the actual volumes of the target using linear regression analysis. For treatment planning purposes we overlapped the reconstructed AVM on the CT slices of the head. The above feature is to our knowledge a feature that the majority of the commercial stereotactic radiotherapy treatment planning system could not provide. The implementation of the method into ISIS TPS shows that we can reliably approximate and visualize the target volume.

On-axis and off-axis primary dose component in high energy photon beams.

The depth dose of the primary dose component, on axis and off axis of six different x-ray beams, has been determined from transmission measurements in narrow beam geometry with and without flattening filter using a Perspex column of a cross section large enough to ensure electronic equilibrium. In order to derive the primary photon fluence, a correction for the scatter from the column has been applied according to the following method: A number of spectra taken from the literature have been used for computing a scatter coefficient Sc at different depths by convolution of dose spread arrays. Using the relationship between Sc and the single attenuation coefficient mu i to represent each entire spectrum, it has been possible to correct the experimental transmission curves iteratively, until the corresponding values of mu were stabilized and representative of the primary. The measured attenuation coefficients were found to have a linear increase as a function of the distance from the central axis for all the energies and types of linear accelerators. For the same nominal energy, this increase is different from one accelerator to another. The same phenomenon was observed for the attenuation coefficients obtained without the flattening filter in the same experimental conditions. The results are tentatively interpreted considering the angular variation of bremsstrahlung energy spectra with and without a flattening filter as calculated by a Monte Carlo method and they are consistent and useful to take accurately into account the softening of the beam as the off-axis distance increases.

A method for measuring the ionization fraction due to the chamber wall (alpha) and assessing its characteristics.

To calibrate a megavoltage therapy beam using an ionization chamber, it is necessary to know the fraction of the ionization arising in the chamber wall when this is made of a material different than the medium. A method for measuring the ionization fraction produced by electrons arising in the chamber wall (alpha) is presented here. The method uses three measurements at the same point in a medium in order to calculate alpha. These measurements are made using the examined chamber with and without a buildup cap and one reference chamber of wall material equivalent to the medium (i.e., in our case, A1 and A-150 were used as wall materials for the examined and the reference chamber, respectively). Using this method, it is possible to calculate alpha in the medium for a series of irradiation conditions and assess its characteristics. Two main conclusions came out of this assessment. The first one is the independence of alpha from the wall material, even if this is aluminum (alpha is only dependent on wall thickness expressed in g cm-2). The second one is that alpha depends on the irradiation conditions; it increases with field size and depth.