Chloride binding and mobility in sodium carbonate-activated slag pastes and mortars.

This study evaluates the chloride binding capacity and the migration of chloride in sodium carbonate-activated slag cements and mortars. The effect on chloride mobility and binding of adding a calcined layered double hydroxide (CLDH) to the binder mix was also assessed. Significantly improved durability characteristics can be achieved for sodium carbonate-activated slag mortars by the addition of small fractions of CLDH, as a consequence of a higher degree of reaction, higher chloride binding capacity, and the refined pore structures present in these modified materials, in comparison with alkali-activated cements produced without CLDH. The addition of CLDH enables the production of sodium carbonate-activated slag cements with notably reduced chloride ingress compared to silicate activated slag cements.

Biomass Bottom Ash as Supplementary Cementitious Material: The Effect of Mechanochemical Pre-Treatment and Mineral Carbonation.

The need to mitigate the CO2 emissions deriving from the cement industry becomes imperative as the climate crisis advances. An effective strategy to achieve this is increasing the replacement level of cement clinkers by waste-derived supplementary cementitious materials (SCMs). In this study, the use of mechanochemically activated biomass ash for high-volume (up to 40%) substitution of cement is investigated. The effect of mineral carbonation treatment on the performance of the mechanochemically treated biomass ash as SCM was also examined. The results showed that the mechanochemically treated biomass ash was the most effective SCM, with the respective samples at 40% cement replacement reaching 63% of the strength at 28 days as compared to samples with 100% Portland cement, while only 17% of the strength was achieved in samples with 40% untreated biomass ash. As suggested by the isothermal calorimetry, XRD, FTIR, and TG analysis, the mechanochemical treatment enhanced the reactivity and the filler effect of the biomass ash, leading to improved mechanical performances of these mortars compared to those containing untreated biomass ash. Mineral carbonation reduced the reactivity of the mechanochemically treated biomass ash but still led to better strength performances in comparison to the untreated biomass ash.

Thermodynamic properties of sodium aluminosilicate hydrate (N-A-S-H).

This study presents for the first time a systematic investigation of the thermodynamic properties of sodium aluminosilicate hydrate (N-A-S-H), through dissolution of pure synthetic N-A-S-H gels. Changes to the chemical composition and gel structure of N-A-S-H were determined via characterisation of the solid phase before and after dissolution by multinuclear solid state nuclear magnetic resonance spectroscopy, scanning electron microscopy coupled with energy dispersive X-ray spectroscopy, and X-ray diffraction measurements. The correlations between the bulk Si/Al ratio of the N-A-S-H phase and its thermodynamic properties were studied by characterisation of the aqueous phase and calculation of solubility constants. The solubility of synthetic N-A-S-H was compared with the solubility of metakaolin-based geopolymers with similar bulk Si/Al ratios. The solubility (log10 Ksp) of both the synthetic N-A-S-H gels and metakaolin-based geopolymers showed a close to linear correlation with the bulk Si/Al ratio of the phase. Lower solubility was observed for N-A-S-H gels and geopolymers with a higher bulk Si/Al ratio. This new insight is fundamental to understanding the physiochemical properties of geopolymers, and provides essential information for predicting their long-term stability and durability.

Micro-fabricated electrochemical chloride ion sensors: From the present to the future.

The real-time detection and monitoring of chloride ion concentrations play important roles in broad industrial applications, including wearable health care device, environmental pollutant control and infrastructure corrosion monitoring. The development of all-solid-state micro-fabricated electrochemical sensors has enabled the miniaturisation of these testing devices. This study reviewed the micro-fabricated electrochemical chloride sensors developed since 1970s, together with a brief summary regarding the progression of miniaturised electrochemical sensors in the past half century. Three major types of electrochemical chloride sensors with specific ion-selectivity have been discussed, the potentiometric sensors (including both ion-selective electrodes and chemical FETs), the chronopotentiometric sensors and the voltammetric sensors. In addition, colorimetric sensors, an emerging low-cost, portable, fast diagnose sensor technique has been included in this review. Four critical sensor performances have been reviewed and compared systematically, the sensibility (chloride concentration range), selectivity, lifetime and applicable pH ranges. The future perspectives for engineering applications proposed in this review will benefit the further development of integrated multi-functional sensors, as well as new instrumental testing methods.

Incorporation of strontium and calcium in geopolymer gels.

Radioactive waste streams containing 90Sr, from nuclear power generation and environmental cleanup operations, are often immobilised in cements to limit radionuclide leaching. Due to poor compatibility of certain wastes with Portland cement, alternatives such as alkali aluminosilicate 'geopolymers' are being investigated. Here, we show that the disordered geopolymers ((N,K)-A-S-H gels) formed by alkali-activation of metakaolin can readily accommodate the alkaline earth cations Sr2+ and Ca2+ into their aluminosilicate framework structure. The main reaction product identified in gels cured at both 20 °C and 80 °C is a fully polymerised Al-rich (N,K)-A-S-H gel comprising Al and Si in tetrahedral coordination, with Si in Q4(4Al) and Q4(3Al) sites, and Na+ and K+ balancing the negative charge resulting from Al3+ in tetrahedral coordination. Faujasite-Na and partially Sr-substituted zeolite Na-A form within the gels cured at 80 °C. Incorporation of Sr2+ or Ca2+ displaces some Na+ and K+ from the charge-balancing sites, with a slight decrease in the Si/Al ratio of the (N,K)-A-S-H gel. Ca2+ and Sr2+ induce essentially the same structural changes in the gels. This is important for understanding the mechanism of incorporation of Sr2+ and Ca2+ in geopolymer cements, and suggests that geopolymer gels are excellent candidates for immobilisation of radioactive waste containing 90Sr.

Alkali aluminosilicate geopolymers as binders to encapsulate strontium-selective titanate ion-exchangers.

Alkali-activated metakaolin geopolymers are attracting interest in the conditioning of nuclear wastes, especially for their ability to immobilise cationic species. However, there is limited understanding of the chemical interactions between the encapsulated spent ion-exchangers, used for decontaminating waste water, and the host aluminosilicate matrix. The lack of such understanding makes it difficult to predict the long-term stability of the waste form. In this study, the suitability of using metakaolin based geopolymer as a matrix for encapsulation of titanate-type ion-exchangers loaded with non-radioactive Sr was investigated for the first time, via spectroscopic and microstructural inspection of the encapsulated ion-exchangers and the aluminosilicate gel matrix. The microstructural and chemical properties of metakaolin geopolymers remained stable after encapsulating titanate type spent ion-exchangers, performed desirably as host materials for conditioning of Sr-loaded titanate ion-exchangers.