A first-cycle coulombic efficiency higher than 100% observed for a Li2MO3 (M = Mo or Ru) electrode.

The lithiation/de-lithiation behavior of a ternary oxide (Li2MO3, where M = Mo or Ru) is examined. In the first lithiation, the metal oxide (MO2) component in Li2MO3 is lithiated by a conversion reaction to generate nano-sized metal (M) particles and two equivalents of Li2O. As a result, one idling Li2O equivalent is generated from Li2MO3. In the de-lithiation period, three equivalents of Li2O react with M to generate MO3. The first-cycle Coulombic efficiency is theoretically 150% since the initial Li2MO3 takes four Li(+) ions and four electrons per formula unit, whereas the M component is oxidized to MO3 by releasing six Li(+) ions and six electrons. In practice, the first-cycle Coulombic efficiency is less than 150% owing to an irreversible charge consumption for electrolyte decomposition. The as-generated MO3 is lithiated/de-lithiated from the second cycle with excellent cycle performance and rate capability.

Multilevel Reset Dependent Set of a Biodegradable Memristor with Physically Transient.

The electronic device, with its biocompatibility, biodegradability, and ease of fabrication process, shows great potential to embed into health monitoring and hardware data security systems. Herein, polyvinylpyrrolidone (PVP) biopolymer is presented as an active layer, electrochemically active magnesium (Mg) as a metal electrode, and chitosan-based substrate (CHS) to fabricate biocompatible and biodegradable physically transient neuromorphic device (W/Mg/PVP/Mg/CHS). The I-V curve of device is non-volatile bipolar in nature and shows a unique compliance-induced multilevel RESET-dependent-SET behavior while sweeping the compliance current from a few microamperes to milliamperes. Non-volatile and stable switching properties are demonstrated with a long endurance test (100 sweeps) and retention time of over 104  s. The physically transient memristor (PTM) has remarkably high dynamic RON /ROFF (ON/OFF state resistance) ratio (106 Ω), and when placed in deionized (DI) water, the device is observed to completely dissolve within 10 min. The pulse transient measurements demonstrate the neuromorphic computation capabilities of the device in the form of excitatory post synaptic current (EPSC), potentiation, depression, and learning behavior, which resemble the biological function of neurons. The results demonstrate the potential of W/Mg/PVP/Mg/CHS device for use in future healthcare and physically transient electronics.

Exome sequencing identified five novel USH2A variants in Korean patients with retinitis pigmentosa.

BACKGROUND: Retinitis pigmentosa (RP) is an inherited disorder that causes progressive loss of vision. This study aimed to describe the possible causative variants of the USH2A gene in Korean RP families and their associated phenotypes. MATERIALS AND METHODS: We recruited 94 RP families (220 subjects, including 94 probands and 126 family members) in a Korean cohort, and analyzed USH2A gene variants through whole-exome sequencing. The pathogenicity of the variants was classified according to American College of Medical Genetics and Genomics and Association for Molecular Pathology guidelines. RESULTS: We found 14 USH2A disease-causing variants, including 5 novel variants. Disease causing variants were identified in 10 probands with RP, accounting for 10.6% (10/94) of the Korean RPs in the cohort. To visually represent the structural changes induced by novel variants, we modeled the three-dimensional structures of the wild-type and mutant proteins. CONCLUSIONS: This study expands the spectrum of USH2A variants and provides information for future therapeutic strategies for RP.

Elucidating Ion Transport Phenomena in Sulfide/Polymer Composite Electrolytes for Practical Solid-State Batteries.

Despite the enormous interest in inorganic/polymer composite solid-state electrolytes (CSEs) for solid-state batteries (SSBs), the underlying ion transport phenomena in CSEs have not yet been elucidated. Here, we address this issue by formulating a mechanistic understanding of bi-percolating ion channels formation and ion conduction across inorganic-polymer electrolyte interfaces in CSEs. A model CSE is composed of argyrodite-type Li6PS5Cl (LPSCl) and gel polymer electrolyte (GPE, including Li+-glyme complex as an ion-conducting medium). The percolation threshold of the LPSCl phase in the CSE strongly depends on the elasticity of the GPE phase. Additionally, manipulating the solvation/desolvation behavior of the Li+-glyme complex in the GPE facilitates ion conduction across the LPSCl-GPE interface. The resulting scalable CSE (area = 8 × 6 (cm × cm), thickness ~ 40 µm) can be assembled with a high-mass-loading LiNi0.7Co0.15Mn0.15O2 cathode (areal-mass-loading = 39 mg cm-2) and a graphite anode (negative (N)/positive (P) capacity ratio = 1.1) in order to fabricate an SSB full cell with bi-cell configuration. Under this constrained cell condition, the SSB full cell exhibits high volumetric energy density (480 Wh Lcell-1) and stable cyclability at 25 °C, far exceeding the values reported by previous CSE-based SSBs.

Dipole Moment- and Molecular Orbital-Engineered Phosphine Oxide-Free Host Materials for Efficient and Stable Blue Thermally Activated Delayed Fluorescence.

To utilize thermally activated delayed fluorescence (TADF) technology for future displays, it is necessary to develop host materials which harness the full potential of blue TADF emitters. However, no publication has reported such hosts yet. Although the most popular host for blue TADF, bis[2-(diphenylphosphino)phenyl]ether oxide (DPEPO) guarantees high-maximum external quantum efficiency (EQEmax ) TADF devices, they exhibit very short operational lifetimes. In contrast, long-lifespan blue TADF devices employing stable hosts such as 3',5-di(9H-carbazol-9-yl)-[1,1'-biphenyl]-3-carbonitrile (mCBP-CN) exhibit much lower EQEmax than the DPEPO-employed devices. Here, an elaborative approach for designing host molecules is suggested to achieve simultaneously stable and efficient blue TADF devices. The approach is based on engineering the molecular geometry, ground- and excited-state dipole moments of host molecules. The engineered hosts significantly enhance delayed fluorescence quantum yields of TADF emitters, as stabilizing the charge-transfer excited states of the TADF emitters and suppressing exciton quenching, and improve the charge balance. Moreover, they exhibit both photochemical and electrochemical stabilities. The best device employing one of the engineered hosts exhibits 79% increase in EQEmax compared to the mCBP-CN-employed device, together with 140% and 92-fold increases in operational lifetime compared to the respective mCBP-CN- and the DPEPO-based devices.

Silicon-Based Technologies for Flexible Photovoltaic (PV) Devices: From Basic Mechanism to Manufacturing Technologies.

Over the past few decades, silicon-based solar cells have been used in the photovoltaic (PV) industry because of the abundance of silicon material and the mature fabrication process. However, as more electrical devices with wearable and portable functions are required, silicon-based PV solar cells have been developed to create solar cells that are flexible, lightweight, and thin. Unlike flexible PV systems (inorganic and organic), the drawbacks of silicon-based solar cells are that they are difficult to fabricate as flexible solar cells. However, new technologies have emerged for flexible solar cells with silicon. In this paper, we describe the basic energy-conversion mechanism from light and introduce various silicon-based manufacturing technologies for flexible solar cells. In addition, for high energy-conversion efficiency, we deal with various technologies (process, structure, and materials).

Characteristics of Aluminum-Doped Zinc Oxide Films Grown Using Facing Target Sputtering for Transparent Electrode of Heterojunction Solar Cells.

In general sputtering, material characteristics can be degraded by high-energy particles located inside the plasma owing to the thin film surface. However, facing target sputtering (FTS) can be used to produce high-quality thin films through maximum control over substrate damage and the reduction of layer damage caused by high-energy particles impacting the substrate. Transparent conductive oxides (TCOs) are being applied to a variety of technologies, including displays and solar cells. The typical transparent electrode material is indium tin oxide (ITO), which contains rare and expensive raw materials. Aluminum-doped zinc oxide (AZO) has attracted increasing attention as a substitute to ITO because it is composed of abundantly available resources and is generally inexpensive. In this study, an AZO thin film was prepared using an FTS system for heterojunction solar cells. The effects of the deposition substrate temperature on the resulting electrical conductivity, structural properties, and optical properties of the AZO thin films were examined.

Enhancing Performance of Perovskite Solar Cells by TiCl4 Treatment on the Surface Roughness of the Titanium Dioxide Layer.

Perovskite solar cells have been attracting extensive attention because of their superior photovoltaic performances and lower costs as compared to those of prevailing photovoltaic technologies. There are four main interfaces in perovskite solar cells: flourine-doped tin oxide/electron transport layer, electron transport layer/perovskite layer, perovskite layer/hole transport layer, and hole transport layer/metal electrode. Among them, the interface between the perovskite layer (general formula RPbX3) and electron transport layer significantly affects the power conversion efficiency. In this study, a layer of TiO2, which is the most popular metal oxides used for perovskite solar cells applications, was deposited as the electron transport layer. To enhance the perovskite solar cells performance, surface treatment was performed with TiCl4 (80 mM). To investigate the effect of TiCl4 treatment, ultraviolet-visible spectroscopy was performed on the perovskite film. Atomic force microscopy, X-ray diffraction, scanning electron microscopy and performance of perovskite solar cells have been also evaluated in this paper. The results indicated that the TiCl4 treatment significantly improved the perovskite solar cells performance.

Particle Size Effect of Lanthanum-Modified Bismuth Titanate Ceramics on Ferroelectric Effect for Energy Harvesting.

Piezoelectric nanogenerators (PNGs) have been studied as renewable energy sources. PNGs consisting of organic piezoelectric materials such as poly(vinylidene fluoride) (PVDF) containing oxide complex powder have attracted much attention for their stretchable and high-performance energy conversion. In this study, we prepared a PNG combined with PVDF and lanthanum-modified bismuth titanate (Bi4-XLaXTi3O12, BLT) ceramics as representative ferroelectric materials. The inserted BLT powder was treated by high-speed ball milling and its particle size reduced to the nanoscale. We also investigated the effect of particle size on the energy-harvesting performance of PNG without polling. As a result, nano-sized powder has a much larger surface area than micro-sized powder and is uniformly distributed inside the PNG. Moreover, nano-sized powder-mixed PNG generated higher power energy (> 4 times) than the PNG inserted micro-sized powder.

Reduced Defects and Enhanced Performance of (FAPbI3)0.97(MAPbBr3)0.03-Based Perovskite Solar Cells by Trimesic Acid Additives.

A high-quality organolead trihalide perovskite film with large-sized crystalline grains and smooth surfaces is required to obtain efficient perovskite solar cells (PSCs). Herein, high-quality (FAPbI3)0.97(MAPbBr3)0.03 perovskite films were fabricated using trimesic acid (TMA) additives in a halide perovskite precursor solution to obtain efficient PSCs. The X-ray diffraction analysis and scanning electron microscopy of the films revealed that the TMA had a significant effect on the roughness of the films by acting as a surface link, thus reducing the surface defects and recombination at the grain boundaries. In addition, with the addition of the TMA additive, a smooth perovskite film with a flat surface and no pinholes was obtained. The perovskite film was used to fabricate a PSC device, and the device exhibited a high power conversion efficiency of 17.26%, which was higher than that of the control device (15.15%) under the same conditions. This study demonstrates a facile method to passivate defects on the perovskite layer via surface modification.

Facile Synthesis of Spherical TiO2 Hollow Nanospheres with a Diameter of 150 nm for High-Performance Mesoporous Perovskite Solar Cells.

The electron transport layer (ETL) of organic-inorganic perovskite solar cells plays an important role in their power conversion efficiency (PCE). In this study, TiO2 hollow nanospheres with a diameter of 150 nm were prepared by a facile synthesis method. The synthesized TiO2 hollow nanospheres had a highly porous structure with a surface area of 85.23 m2 g-1, which is significantly higher than commercial TiO2 (P25) (54.32 m2 g-1), indicating that they can form an ideal mesoporous layer for Formamidinium iodide-based perovskite solar cells (PSCs). In addition, the nanospheres achieved a remarkable perovskite performance, and the average PCE increased from 12.87% to 14.27% with a short circuit current density of 22.36 mAcm-2, an open voltage of 0.95 V, and a fill factor of 0.65. The scanning electron microscopy images revealed that the enhanced PCE could be due to the improved carrier collection and transport properties of the nanosphere, which enabled efficient filtration of perovskite into the TiO2 mesoporous ETL. The TiO2 hollow nanospheres fabricated in this study show high potential as a high-quality ETL material for efficient (FAPbI3)0.97(MAPbBr3)0.03-based PSCs.

Practical Demonstration of Deep-Ultraviolet Detection with Wearable and Self-Powered Halide Perovskite-Based Photodetector.

Flexible and self-powered photodetectors (PDs) have become one of the most popular topics, attracting researchers in the field of optoelectronic applications. In this study, for the first time, we demonstrate partial discharge detection in a practical environment with a prepared flexible device. Poly(vinylidene fluoride) (PVDF) is utilized as a highly transparent material in the UVC region, to create a flexible substrate with the antihumidity property. A detector that uses a mixed-halide perovskite (FAPbI3)1-x(MAPbBr3)x as the photoactive material is constructed in a vertical structure on the as-prepared hydrophobic PVDF substrate. The fabricated device exhibits good performance with a fast response speed (trise = 82 ms, tfall = 64 ms) and a high detectivity of 7.21 × 1010 Jones at zero bias under 254 nm UV illumination, along with superior mechanical flexibility at various bending angles. Additionally, the air-exposure stability and reproducibility of the as-prepared device exhibit almost the original performance after 6 weeks of storage. For practical applications, we demonstrate a facile and sensitive detection for UVC leakage from a germicidal lamp and simulated a partial discharge system using our PD without energy consumption. These results indicate that this new approach may be useful and convenient for the detection of the partial discharge as well as for several practical applications.

Characteristics of Perovskite Solar Cells (PSCs) with Various Metal Electrode Deposited Using Thermal Evaporators.

Organic material-based solar cell devices such as perovskite solar cells (PSCs) have attracted attention as renewable energy resources with low production cost, lightweight, wearable device applications, and large-area processability. To enhance device performance, many research groups have attempted to develop new materials and structures. Metal electrode materials play an important role in solar energy conversion in PSCs, owing to the ohmic contact and contact resistance between metal negative electrodes and photoactive layers. Until recently, conventional metal sources such as Ag, Au, or Cu have been used as electrodes. In this study, PSCs were employed in various metal negative electrodes using a thermal evaporator. The authors investigated the effect of metal negative electrodes on PSCs.

Template Engineering of Metal-to-Insulator Transitions in Epitaxial Bilayer Nickelate Thin Films.

Understanding metal-to-insulator phase transitions in solids has been a keystone not only for discovering novel physical phenomena in condensed matter physics but also for achieving scientific breakthroughs in materials science. In this work, we demonstrate that the transport properties (i.e., resistivity and transition temperature) in the metal-to-insulator transitions of perovskite nickelates are tunable via the epitaxial heterojunctions of LaNiO3 and NdNiO3 thin films. A mismatch in the oxygen coordination environment and interfacial octahedral coupling at the oxide heterointerface allows us to realize an exotic phase that is unattainable in the parent compound. With oxygen vacancy formation for strain accommodation, the topmost LaNiO3 layer in LaNiO3/NdNiO3 bilayer thin films is structurally engineered and it electrically undergoes a metal-to-insulator transition that does not appear in metallic LaNiO3. Modification of the NdNiO3 template layer thickness provides an additional knob for tailoring the tilting angles of corner-connected NiO6 octahedra and the linked transport characteristics further. Our approaches can be harnessed to tune physical properties in complex oxides and to realize exotic physical phenomena through oxide thin-film heterostructuring.

Change of Phase Transition Temperature in Band Engineered Ferroelectric Lanthanum-Modified Bismuth Titanates.

The ferroelectric material chosen for a solar cell has to absorb as much of the solar spectrum as possible, therefore a low band gap is desirable, but it is rarely known for phase transition temperature on the bandgap engineered ferroelectric materials. The phase transition temperature of a ferroelectric material can be determined by monitoring its dielectric constant with increasing temperature, as the dielectric constant changes abruptly at the phase transition temperature. Here, we inform the measurement of the phase transition temperature of the ferroelectric complex oxide Bi3.25La0.75Ti3O12 as well as cobalt and iron doped Bi3.25La0.75Ti3O12 bulk ceramics for photovoltaic cells based on dielectric monitoring with changing temperature. We synthesized lanthanum-modified bismuth-titanate-based ceramics with various doping concentrations transition metal to Ti. X-ray diffraction analysis revealed that all the compounds crystallized in an orthorhombic structure. Their morphologies and size distributions were observed using scanning electron microscopy. From the ultraviolet-visible spectroscopy absorption spectra of the synthesized powder, bandgaps were checked. An inductance-capacitance-resistance meter was used to obtain the relationship between dielectric responses and the temperature of the targets in a tube furnace. We observed that the dielectric constant increases gradually with increasing temperature, until the transition temperature and subsequently decreases, and we were able to determine the phase transition temperatures of the tested materials. Furthermore, the results revealed that all the doped bismuth titanates keep their phase transition temperatures, which were sufficiently high, to maintain their ferroelectric properties above room temperature.

Transcriptome Profiling Associated with Carcass Quality of Loin Muscles in Crossbred Pigs.

Carcass quality traits, such as lean depth and loin depth, are of extreme economic importance for the swine industry. This study aimed to identify the gene expression pattern related to carcass quality in crossbred pigs ((Landrace × Yorkshire) × Duroc). In total, 20 crossbred pigs were used in this study and they were divided into two groups (class I grade, n = 10; class II grade, n = 10) based on the carcass grades. Total RNA samples extracted from the loin muscles of both groups were submitted for RNA-seq. The quality assessment of the sequencing reads resulted in 25,458 unigenes and found 12,795 candidate coding unigenes with homology to other species after annotation. Differentially expressed gene (DEG) analysis of the two groups revealed 282 up-regulated and 189 down-regulated genes (p ≤ 0.01), linked to tissue development, striated muscle tissue development, tissue morphogenesis, and lipid metabolic process gene ontology (GO) terms. Kyoto Encyclopedia of Genes and Genomes (KEGG) enrichment analysis highlighted genes related to the calcium signaling pathway, melanogenesis, the sphingolipid signaling pathway, the apelin signaling pathway, and the mTOR signaling pathway. We constructed an expressed gene profile, which may serve as a resource for genomic studies focused on uncovering the molecular mechanisms underlying carcass quality in crossbred pigs.

Characteristics of Perovskites ReNiO3 (Re = La and Nd) Prepared by Solid State Reaction in the Ambient of Oxygen.

In the proposed method, we could complete the synthesis with only 3 h of thermal treatment, which is relatively fast in comparison to the previously reported procedure, without an expensive gascontrolled chamber system. The compound comprises Re2O3 and NiO3 powders that were mixed thoroughly in a stoichiometric ratio in a ball mill for 24 h and then dried in an oven at a 100 °C. The powder mixture was quickly calcined at various temperature for at least 3 h in an oxygen gas flow compared to conventional annealing method. After calcination at 1100 °C, the detected XRD peaks matched well with peaks of the standard ABO3 perovskite structure. Moreover, EDX and FT-IR spectral analysis results confirmed that the mixture had formed stoichiometry ReNiO3. All prepared samples comprised plate-like grains with a random orientation, and their average particle size was in the range of 1 to 3 µm calculated from FE-SEM images.

Characterization of Perovskite Solar Cell with Fe3+ Doped TiO2 Layer.

Recently, single-crystal silicon solar cells have achieved efficiencies of 25%. However, their production is energy-demanding and relatively expensive. Therefore, photovoltaic cells based on organic- inorganic hybrid perovskites have attracted considerable attention owing to their high conversion efficiencies, simple preparation, and potentially low production costs. In this study, we investigated the effect of Fe3+ doped into a compact and mesoporous layer of TiO2 on the efficiency of the resultant perovskite solar cell (PSC). The efficiencies achieved for PSCs with Fe3+/TiO2 were higher than those for cells with pure TiO2 nanoparticles. The samples were characterized by X-ray diffraction, scanning electron microscopy, ultraviolet-visible spectroscopy, and current-voltage measurements. The photoelectrode PSC exhibited a high light-to-electric-energy conversion efficiency under a simulated solar light irradiation of 100 mW/cm² (AM 1.5). Our results suggest that Fe3+ nanoparticles in the TiO2 layer may contribute to the performance improvement of the PSC.

Surface Energy Change of Atomic-Scale Metal Oxide Thin Films by Phase Transformation.

Fine-tuning of the surface free energy (SFE) of a solid material facilitates its use in a wide range of applications requiring precise control of the ubiquitous presence of liquid on the surface. In this study, we found that the SFE of rare-earth oxide (REO) thin films deposited by atomic layer deposition (ALD) gradually decreased with increasing film thickness; however, these changes could not be understood by classical interaction models. Herein, the mechanism underlying the aforesaid decrease was systematically studied by measuring contact angles, surface potential, adhesion force, crystalline structures, chemical compositions, and morphologies of the REO films. A growth mode of the REO films was observed: layer-by-layer growth at the initial stage with an amorphous phase and subsequent crystalline island growth, accompanied by a change in the crystalline structure and orientation that affects the SFE. The portion of the surface crystalline facets terminated with (222) and (440) planes evolved with an increase in ALD cycles and film thickness, as an amorphous phase was transformed. Based on this information, we demonstrated an SFE-tuned liquid tweezer with selectivity to target liquid droplets. We believe that the results of this fundamental and practical study, with excellent selectivity to liquids, will have significant impacts on coating technology.

A novel approach for the direct conversion of alkylsulfonyl derivatives into alkylcarbonyl derivatives via tin-free radical carbonylation.

A novel radical approach for the direct conversion of RSO(2)X into RCOX in a single step is devised; the present approach is very simple, highly efficient, and minimizes formation of by-product.