Characterization of a DFG comb showing quadratic scaling of the phase noise with frequency.

We characterize an Er:fiber laser frequency comb that is passively carrier envelope phase-stabilized via difference frequency generation at a wavelength of 1550 nm. A generic method to measure the comb linewidth at different wavelengths is demonstrated. By transferring the properties of a comb line to a cw external cavity diode laser, the phase noise is subsequently measured by tracking the delayed self-heterodyne beat note. This relatively simple characterization method is suitable for a broad range of optical frequencies. Here, it is used to characterize our difference frequency generation (DFG) comb over nearly an optical octave. With repetition-rate stabilization, a radiofrequency reference oscillator limited linewidth is achieved. A lock to an optical reference shows out-of-loop linewidths of the comb at the hertz level. The phase noise measurements are in excellent agreement with the elastic tape model with a fix point at zero frequency.

Solving self-mixing equations for arbitrary feedback levels: a concise algorithm.

Self-mixing laser sensors show promise for a wide range of sensing applications, including displacement, velocimetry, and fluid flow measurements. Several techniques have been developed to simulate self-mixing signals; however, a complete and succinct process for synthesizing self-mixing signals has so far been absent in the open literature. This article provides a systematic numerical approach for the analysis of self-mixing sensors using the steady-state solution to the Lang and Kobayashi model. Examples are given to show how this method can be used to synthesize self-mixing signals for arbitrary feedback levels and for displacement, distance, and velocity measurement. We examine these applications with a deterministic stimulus and discuss the velocity measurement of a rough surface, which necessitates the inclusion of a random stimulus.

Spectral broadening caused by dynamic speckle in self-mixing velocimetry sensors.

Self-mixing laser sensors require few components and can be used to measure velocity. The self-mixing laser sensor consists of a laser emitting a beam focused onto a rough target that scatters the beam with some of the emission re-entering the laser cavity. This 'self-mixing' causes measurable interferometric modulation of the laser output power that leads to a periodic Doppler signal spectrum with a peak at a frequency proportional to the velocity of the target. Scattering of the laser emission from a rough surface also leads to a speckle effect that modulates the Doppler signal causing broadening of the signal spectrum adding uncertainty to the velocity measurement. This article analyzes the speckle effect to provide an analytic equation to predict the spectral broadening of an acquired self-mixing signal and compares the predicted broadening to experimental results. To the best of our knowledge, the model proposed in this article is the first model that has successfully predicted speckle broadening in a self-mixing velocimetry sensor in a quantitative manner. It was found that the beam spot size on the target and the target speed affect the resulting spectral broadening caused by speckle. It was also found that the broadening is only weakly dependent on target angle. The experimental broadening was consistently greater than the theoretical speckle broadening due to other effects that also contribute to the total broadening.

Maintaining maximum signal-to-noise ratio in uncooled vertical-cavity surface-emitting laser-based self-mixing sensors.

We demonstrate a method for maintaining the maximum signal-to-noise ratio (SNR) of the signal obtained from the self-mixing sensor based on a vertical-cavity surface-emitting laser (VCSEL). It was found that the locus of the maximum SNR in the current-temperature space can be well approximated by a simple analytical model related to the temperature behavior of the VCSEL threshold current. The optimum sensor performance is achieved by tuning the laser current according to the proposed model, thus enabling the sensor to operate without temperature stabilization in a wide temperature range between -20 °C and +80 °C.

Terahertz imaging through self-mixing in a quantum cascade laser.

We demonstrate terahertz (THz) frequency imaging using a single quantum cascade laser (QCL) device for both generation and sensing of THz radiation. Detection is achieved by utilizing the effect of self-mixing in the THz QCL, and, specifically, by monitoring perturbations to the voltage across the QCL, induced by light reflected from an external object back into the laser cavity. Self-mixing imaging offers high sensitivity, a potentially fast response, and a simple, compact optical design, and we show that it can be used to obtain high-resolution reflection images of exemplar structures.

Self-mixing flow sensor using a monolithic VCSEL array with parallel readout.

The self-mixing sensing technique is a compact, interferometric sensing technique that can be used for measuring fluid flows. In this work, we demonstrate a parallel readout self-mixing flow velocity sensing system based on a monolithic Vertical-Cavity Surface-Emitting Laser (VCSEL) array. The parallel sensing scheme enables high-resolution full-field imaging systems employing electronic scanning with faster acquisition rates than mechanical scanning systems. The self-mixing signal is acquired from the variation in VCSEL junction voltage, thus markedly reducing the system complexity. The system was validated by measuring velocity distribution of fluid in a custom built diverging-converging planar flow channel. The results obtained agree well with simulation and demonstrate the feasibility of high frame-rate and resolution parallel self-mixing sensors.

GaN laser self-mixing velocimeter for measuring slow flows.

The self-mixing (SM) laser sensing technique allows for a simple, self-aligned, and robust system for measuring velocity. Low-cost blue emitting GaN laser diodes have recently become available owing to the high volume requirements for Blu-ray Disc devices such as high-definition video players and gaming consoles. These GaN lasers have a significantly shorter wavelength (around 405 nm) compared with other semiconductor lasers (generally around 800 nm for SM sensors). Therefore, if used in SM flow sensors, they allow measuring of flow rates that would otherwise be too slow to measure. In this Letter we report what we believe to be the world's first SM flow measurement system based on a blue emitting semiconductor laser, demonstrating the ability to measure flow rates down to 26 microm/s.

Self-mixing imaging sensor using a monolithic VCSEL array with parallel readout.

The advent of two-dimensional arrays of Vertical-Cavity Surface-Emitting Lasers (VCSELs) opened a range of potential sensing applications for nanotechnology and life-sciences. With each laser independently addressable, there is scope for the development of high-resolution full-field imaging systems with electronic scanning. We report on the first implementation of a self-mixing imaging system with parallel readout based on a monolithic VCSEL array. A self-mixing Doppler signal was acquired from the variation in VCSEL junction voltage rather than from a conventional variation in laser power, thus markedly reducing the system complexity. The sensor was validated by imaging the velocity distribution on the surface of a rotating disc. The results obtained demonstrate that monolithic arrays of Vertical-Cavity lasers present a powerful tool for the advancement of self-mixing sensors into parallel imaging paradigms and provide a stepping stone to the implementation of a full-field self-mixing sensor systems.

Rodent scope: a user-configurable digital wireless telemetry system for freely behaving animals.

This paper describes the design and implementation of a wireless neural telemetry system that enables new experimental paradigms, such as neural recordings during rodent navigation in large outdoor environments. RoSco, short for Rodent Scope, is a small lightweight user-configurable module suitable for digital wireless recording from freely behaving small animals. Due to the digital transmission technology, RoSco has advantages over most other wireless modules of noise immunity and online user-configurable settings. RoSco digitally transmits entire neural waveforms for 14 of 16 channels at 20 kHz with 8-bit encoding which are streamed to the PC as standard USB audio packets. Up to 31 RoSco wireless modules can coexist in the same environment on non-overlapping independent channels. The design has spatial diversity reception via two antennas, which makes wireless communication resilient to fading and obstacles. In comparison with most existing wireless systems, this system has online user-selectable independent gain control of each channel in 8 factors from 500 to 32,000 times, two selectable ground references from a subset of channels, selectable channel grounding to disable noisy electrodes, and selectable bandwidth suitable for action potentials (300 Hz-3 kHz) and low frequency field potentials (4 Hz-3 kHz). Indoor and outdoor recordings taken from freely behaving rodents are shown to be comparable to a commercial wired system in sorting for neural populations. The module has low input referred noise, battery life of 1.5 hours and transmission losses of 0.1% up to a range of 10 m.