First-Principles Simulation and Materials Screening for Spin-Orbit Torque in 2D van der Waals Heterostructures.

Recent advancements in spin-orbit torque (SOT) technology in two-dimensional van der Waals (2D vdW) materials have not only pushed spintronic devices to their atomic limits but have also unveiled unconventional torques and novel spin-switching mechanisms. The vast diversity of SOT observed in numerous 2D vdW materials necessitates a screening strategy to identify optimal materials for torque device performance. However, such a strategy has yet to be established. To address this critical issue, a combination of density functional theory and non-equilibrium Green's function is employed to calculate the SOT in various 2D vdW bilayer heterostructures. This leads to the discovery of three high SOT systems: WTe2/CrSe2, MoTe2/VS2, and NbSe2/CrSe2. Furthermore, a figure of merit that allows for rapid and efficient estimation of SOT is proposed, enabling high-throughput screening of optimal materials and devices for SOT applications in the future.

WSe2 Homojunction Devices: Electrostatically Configurable as Diodes, MOSFETs, and Tunnel FETs for Reconfigurable Computing.

In this paper, electrostatically configurable 2D tungsten diselenide (WSe2 ) electronic devices are demonstrated. Utilizing a novel triple-gate design, a WSe2 device is able to operate as a tunneling field-effect transistor (TFET), a metal-oxide-semiconductor field-effect transistor (MOSFET) as well as a diode, by electrostatically tuning the channel doping to the desired profile. The implementation of scaled gate dielectric and gate electrode spacing enables higher band-to-band tunneling transmission with the best observed subthreshold swing (SS) among all reported homojunction TFETs on 2D materials. Self-consistent full-band atomistic quantum transport simulations quantitatively agree with electrical measurements of both the MOSFET and TFET and suggest that scaling gate oxide below 3 nm is necessary to achieve sub-60 mV dec-1 SS, while further improvement can be obtained by optimizing the spacers. Diode operation is also demonstrated with the best ideality factor of 1.5, owing to the enhanced electrostatic control compared to previous reports. This research sheds light on the potential of utilizing electrostatic doping scheme for low-power electronics and opens a path toward novel designs of field programmable mixed analog/digital circuitry for reconfigurable computing.

Electrically Tunable Bandgaps in Bilayer MoS2.

Artificial semiconductors with manufactured band structures have opened up many new applications in the field of optoelectronics. The emerging two-dimensional (2D) semiconductor materials, transition metal dichalcogenides (TMDs), cover a large range of bandgaps and have shown potential in high performance device applications. Interestingly, the ultrathin body and anisotropic material properties of the layered TMDs allow a wide range modification of their band structures by electric field, which is obviously desirable for many nanoelectronic and nanophotonic applications. Here, we demonstrate a continuous bandgap tuning in bilayer MoS2 using a dual-gated field-effect transistor (FET) and photoluminescence (PL) spectroscopy. Density functional theory (DFT) is employed to calculate the field dependent band structures, attributing the widely tunable bandgap to an interlayer direct bandgap transition. This unique electric field controlled spontaneous bandgap modulation approaching the limit of semiconductor-to-metal transition can open up a new field of not yet existing applications.

A tight-binding study of single-atom transistors.

A detailed theoretical study of the electronic and transport properties of a single atom transistor, where a single phosphorus atom is embedded within a single crystal transistor architecture, is presented. Using a recently reported deterministic single-atom transistor as a reference, the electronic structure of the device is represented atomistically with a tight-binding model, and the channel modulation is simulated self-consistently with a Thomas-Fermi method. The multi-scale modeling approach used allows confirmation of the charging energy of the one-electron donor charge state and explains how the electrostatic environments of the device electrodes affects the donor confinement potential and hence extent in gate voltage of the two-electron charge state. Importantly, whilst devices are relatively insensitive to dopant ordering in the highly doped leads, a ∼1% variation of the charging energy is observed when a dopant is moved just one lattice spacing within the device. The multi-scale modeling method presented here lays a strong foundation for the understanding of single-atom device structures: essential for both classical and quantum information processing.

Limits to metallic conduction in atomic-scale quasi-one-dimensional silicon wires.

The recent observation of ultralow resistivity in highly doped, atomic-scale silicon wires has sparked interest in what limits conduction in these quasi-1D systems. Here we present electron transport measurements of gated Si:P wires of widths 4.6 and 1.5 nm. At 4.6 nm we find an electron mobility, µ(el)≃60 cm²/V s, in excellent agreement with that of macroscopic Hall bars. Metallic conduction persists to millikelvin temperatures where we observe Gaussian conductance fluctuations of order δG∼e²/h. In thinner wires (1.5 nm), metallic conduction breaks down at G≲e²/h, where localization of carriers leads to Coulomb blockade. Metallic behavior is explained by the large carrier densities in Si:P δ-doped systems, allowing the occupation of all six valleys of the silicon conduction band, enhancing the number of 1D channels and hence the localization length.

Spin-lattice relaxation times of single donors and donor clusters in silicon.

An atomistic method of calculating the spin-lattice relaxation times (T1) is presented for donors in silicon nanostructures comprising of millions of atoms. The method takes into account the full band structure of silicon including the spin-orbit interaction. The electron-phonon Hamiltonian, and hence, the deformation potential, is directly evaluated from the strain-dependent tight-binding Hamiltonian. The technique is applied to single donors and donor clusters in silicon, and explains the variation of T1 with the number of donors and electrons, as well as donor locations. Without any adjustable parameters, the relaxation rates in a magnetic field for both systems are found to vary as B5, in excellent quantitative agreement with experimental measurements. The results also show that by engineering electronic wave functions in nanostructures, T1 times can be varied by orders of magnitude.

Coherent control of a single ²9Si nuclear spin qubit.

Magnetic fluctuations caused by the nuclear spins of a host crystal are often the leading source of decoherence for many types of solid-state spin qubit. In group-IV semiconductor materials, the spin-bearing nuclei are sufficiently rare that it is possible to identify and control individual host nuclear spins. This Letter presents the first experimental detection and manipulation of a single ²9Si nuclear spin. The quantum nondemolition single-shot readout of the spin is demonstrated, and a Hahn echo measurement reveals a coherence time of T2=6.3(7) ms­in excellent agreement with bulk experiments. Atomistic modeling combined with extracted experimental parameters provides possible lattice sites for the ²9Si atom under investigation. These results demonstrate that single ²9Si nuclear spins could serve as a valuable resource in a silicon spin-based quantum computer.

Utilizing the unique properties of nanowire MOSFETs for RF applications.

Nanostructures have attracted a great deal of attention because of their potential usefulness for high density applications. More importantly, they offer excellent avenues for improved scaling beyond conventional approaches. Less attention has been paid to their intrinsic potential for distinct circuit applications. Here we discuss how a combination of 1-D transport, operation in the quantum capacitance limit, and ballistic transport can be utilized for certain RF applications. In particular this work explores how the above transport properties can provide a high degree of transconductance linearity at the device level. The article also discusses how device characteristics can be interpreted and analyzed in terms of device linearity if the above conditions are not ideally fulfilled. Using aggressively scaled silicon nanowire field-effect transistors as an example device in this work provides new insights toward the proper choice of channel material to improve linearity through the above-mentioned transport conditions. According to this study, a high degree of linearity occurs feasible while operating at low supply voltages making low-dimensional systems, and here in particular nanowires, an interesting candidate for portable RF applications.

Noninvasive spatial metrology of single-atom devices.

The exact location of a single dopant atom in a nanostructure can influence or fully determine the functionality of highly scaled transistors or spin-based devices. We demonstrate here a noninvasive spatial metrology technique, based on the microscopic modeling of three electrical measurements on a single-atom (phosphorus in silicon) spin qubit device: hyperfine coupling, ground state energy, and capacitive coupling to nearby gates. This technique allows us to locate the qubit atom with a precision of ±2.5 nm in two directions and ±15 nm in the third direction, which represents a 1500-fold improvement with respect to the prefabrication statistics obtainable from the ion implantation parameters.

Probing scattering mechanisms with symmetric quantum cascade lasers.

A characteristic feature of quantum cascade lasers is their unipolar carrier transport. We exploit this feature and realize nominally symmetric active regions for terahertz quantum cascade lasers, which should yield equal performance with either bias polarity. However, symmetric devices exhibit a strongly bias polarity dependent performance due to growth direction asymmetries, making them an ideal tool to study the related scattering mechanisms. In the case of an InGaAs/GaAsSb heterostructure, the pronounced interface asymmetry leads to a significantly better performance with negative bias polarity and can even lead to unidirectionally working devices, although the nominal band structure is symmetric. The results are a direct experimental proof that interface roughness scattering has a major impact on transport/lasing performance.

Observation of 1D behavior in Si nanowires: toward high-performance TFETs.

This article provides experimental evidence of one-dimensional behavior of silicon (Si) nanowires (NWs) at low-temperature through both transfer (I(d)-V(G)) and capacitance-voltage characteristics. For the first time, operation of Si NWs in the quantum capacitance limit (QCL) is experimentally demonstrated and quantitatively analyzed. This is of relevance since working in the QCL may allow, e.g., tunneling field-effect transistors (TFETs) to achieve higher on-state currents (I(on)) and larger on-/off-state current ratios (I(on)/I(off)), thus addressing one of the most severe limitations of TFETs. Comparison of the experimental data with simulations finds excellent agreement using a simple capacitor model.

Indirectly pumped 3.7 THz InGaAs/InAlAs quantum-cascade lasers grown by metal-organic vapor-phase epitaxy.

Device-performances of 3.7 THz indirect-pumping quantum-cascade lasers are demonstrated in an InGaAs/InAlAs material system grown by metal-organic vapor-phase epitaxy. The lasers show a low threshold-current-density of ~420 A/cm2 and a peak output power of ~8 mW at 7 K, no sign of parasitic currents with recourse to well-designed coupled-well injectors in the indirect pump scheme, and a maximum operating temperature of Tmax ~100 K. The observed roll-over of output intensities in current ranges below maximum currents and limitation of Tmax are discussed with a model for electron-gas heating in injectors. Possible ways toward elevation of Tmax are suggested.

The polarization response in InAs quantum dots: theoretical correlation between composition and electronic properties.

III-V growth and surface conditions strongly influence the physical structure and resulting optical properties of self-assembled quantum dots (QDs). Beyond the design of a desired active optical wavelength, the polarization response of QDs is of particular interest for optical communications and quantum information science. Previous theoretical studies based on a pure InAs QD model failed to reproduce experimentally observed polarization properties. In this work, multi-million atom simulations are performed in an effort to understand the correlation between chemical composition and polarization properties of QDs. A systematic analysis of QD structural parameters leads us to propose a two-layer composition model, mimicking In segregation and In-Ga intermixing effects. This model, consistent with mostly accepted compositional findings, allows us to accurately fit the experimental PL spectra. The detailed study of QD morphology parameters presented here serves as a tool for using growth dynamics to engineer the strain field inside and around the QD structures, allowing tuning of the polarization response.

Stark tuning of the charge states of a two-donor molecule in silicon.

A singly ionized two-donor molecule in silicon is an interesting test-bed system for implementing a quantum bit using charge degrees of freedom at the atomic limit of device fabrication. The operating principles of such a device are based on wavefunction symmetries defined by charge localizations and energy gaps in the spectrum. The Stark-shifted electronic structure of a two-donor phosphorus molecule is investigated using a multi-million-atom tight-binding framework. The effects of surface (S) and barrier (B) gates are analyzed for various voltage regimes. It is found that gate control is smooth for any donor separation, although at certain donor orientations the S and B gates may alter in functionality. Effects such as interface ionization, saturation of the lowest energy gap, and sensitivity to donor and gate placements are also investigated. Excited molecular states of P(2) + are found to impose limits on the allowed donor separations and operating gate voltages for coherent operation. This work therefore outlines and analyzes the various issues that are of importance in the design and control of such donor molecular systems.

Quantitative excited state spectroscopy of a single InGaAs quantum dot molecule through multi-million-atom electronic structure calculations.

Atomistic electronic structure calculations are performed to study the coherent inter-dot couplings of the electronic states in a single InGaAs quantum dot molecule. The experimentally observed excitonic spectrum by Krenner et al (2005) Phys. Rev. Lett. 94 057402 is quantitatively reproduced, and the correct energy states are identified based on a previously validated atomistic tight binding model. The extended devices are represented explicitly in space with 15-million-atom structures. An excited state spectroscopy technique is applied where the externally applied electric field is swept to probe the ladder of the electronic energy levels (electron or hole) of one quantum dot through anti-crossings with the energy levels of the other quantum dot in a two-quantum-dot molecule. This technique can be used to estimate the spatial electron-hole spacing inside the quantum dot molecule as well as to reverse engineer quantum dot geometry parameters such as the quantum dot separation. Crystal-deformation-induced piezoelectric effects have been discussed in the literature as minor perturbations lifting degeneracies of the electron excited (P and D) states, thus affecting polarization alignment of wavefunction lobes for III-V heterostructures such as single InAs/GaAs quantum dots. In contrast, this work demonstrates the crucial importance of piezoelectricity to resolve the symmetries and energies of the excited states through matching the experimentally measured spectrum in an InGaAs quantum dot molecule under the influence of an electric field. Both linear and quadratic piezoelectric effects are studied for the first time for a quantum dot molecule and demonstrated to be indeed important. The net piezoelectric contribution is found to be critical in determining the correct energy spectrum, which is in contrast to recent studies reporting vanishing net piezoelectric contributions.

MoS2 for Enhanced Electrical Performance of Ultrathin Copper Films.

Copper nanowires are widely used as on-chip interconnects due to their superior conductivity. However, with aggressive Cu interconnect scaling, surface scattering of electrons drastically increases the electrical resistivity. In this work, we have studied the electrical performance of Cu thin films deposited on different materials. By comparing the thickness dependence of Cu films' resistivity on MoS2 and SiO2, we have demonstrated that MoS2 can be used to enhance the electrical performance of ultrathin Cu films due to improved specular surface scattering by up to 40%. By fitting the experimental data with the theoretical Fuchs-Sondheimer (FS) model, we have determined the specularity parameter at the Cu/MoS2 interface to be p ≈ 0.4 at room temperature. Furthermore, first principle calculations based on density functional theory (DFT) indicate that the localized density of states (LDOS) at the Cu/amorphous SiO2 interface is larger than the LDOS at the Cu/MoS2 interface, which is believed to be responsible for the higher resistivity in the Cu thin films that are deposited on SiO2 substrates. Our results suggest that MoS2 may serve as a performance enhancer for future generations of Cu interconnects.

Complementary Black Phosphorus Tunneling Field-Effect Transistors.

Band-to-band tunneling field-effect transistors (TFETs) have emerged as promising candidates for low-power integration circuits beyond conventional metal-oxide-semiconductor field-effect transistors (MOSFETs) and have been demonstrated to overcome the thermionic limit, which results intrinsically in sub-threshold swings of at least 60 mV/dec at room temperature. Here, we demonstrate complementary TFETs based on few-layer black phosphorus, in which multiple top gates create electrostatic doping in the source and drain regions. By electrically tuning the doping types and levels in the source and drain regions, the device can be reconfigured to allow for TFET or MOSFET operation and can be tuned to be n-type or p-type. Owing to the proper choice of materials and careful engineering of device structures, record-high current densities have been achieved in 2D TFETs. Full-band atomistic quantum transport simulations of the fabricated devices agree quantitatively with the current-voltage measurements, which gives credibility to the promising simulation results of ultrascaled phosphorene TFETs. Using atomistic simulations, we project substantial improvements in the performance of the fabricated TFETs when channel thicknesses and oxide thicknesses are scaled down.

Theoretical study of strain-dependent optical absorption in a doped self-assembled InAs/InGaAs/GaAs/AlGaAs quantum dot.

A detailed theoretical study of the optical absorption in doped self-assembled quantum dots is presented. A rigorous atomistic strain model as well as a sophisticated 20-band tight-binding model are used to ensure accurate prediction of the single particle states in these devices. We also show that for doped quantum dots, many-particle configuration interaction is also critical to accurately capture the optical transitions of the system. The sophisticated models presented in this work reproduce the experimental results for both undoped and doped quantum dot systems. The effects of alloy mole fraction of the strain controlling layer and quantum dot dimensions are discussed. Increasing the mole fraction of the strain controlling layer leads to a lower energy gap and a larger absorption wavelength. Surprisingly, the absorption wavelength is highly sensitive to the changes in the diameter, but almost insensitive to the changes in dot height. This behavior is explained by a detailed sensitivity analysis of different factors affecting the optical transition energy.

Low-temperature thermal transport and thermopower of monolayer transition metal dichalcogenide semiconductors.

We study the low temperature thermal conductivity of single-layer transition metal dichalcogenides (TMDCs). In the low temperature regime where heat is carried primarily through transport of electrons, thermal conductivity is linked to electrical conductivity through the Wiedemann-Franz law (WFL). Using a k.p Hamiltonian that describes the [Formula: see text] and [Formula: see text] valley edges, we compute the zero-frequency electric (Drude) conductivity using the Kubo formula to obtain a numerical estimate for the thermal conductivity. The impurity scattering determined transit time of electrons which enters the Drude expression is evaluated within the self-consistent Born approximation. The analytic expressions derived show that low temperature thermal conductivity (1) is determined by the band gap at the valley edges in monolayer TMDCs and (2) in presence of disorder which can give rise to the variable range hopping regime, there is a distinct reduction. Additionally, we compute the Mott thermopower and demonstrate that under a high frequency light beam, a valley-resolved thermopower can be obtained. A closing summary reviews the implications of results followed by a brief discussion on applicability of the WFL and its breakdown in context of the presented calculations.

Silicon quantum processor with robust long-distance qubit couplings.

Practical quantum computers require a large network of highly coherent qubits, interconnected in a design robust against errors. Donor spins in silicon provide state-of-the-art coherence and quantum gate fidelities, in a platform adapted from industrial semiconductor processing. Here we present a scalable design for a silicon quantum processor that does not require precise donor placement and leaves ample space for the routing of interconnects and readout devices. We introduce the flip-flop qubit, a combination of the electron-nuclear spin states of a phosphorus donor that can be controlled by microwave electric fields. Two-qubit gates exploit a second-order electric dipole-dipole interaction, allowing selective coupling beyond the nearest-neighbor, at separations of hundreds of nanometers, while microwave resonators can extend the entanglement to macroscopic distances. We predict gate fidelities within fault-tolerance thresholds using realistic noise models. This design provides a realizable blueprint for scalable spin-based quantum computers in silicon.Quantum computers will require a large network of coherent qubits, connected in a noise-resilient way. Tosi et al. present a design for a quantum processor based on electron-nuclear spins in silicon, with electrical control and coupling schemes that simplify qubit fabrication and operation.