A Novel Closed-Loop Electrical Brain Stimulation Device Featuring Wireless Low-Energy Ultrasound Power and Communication.

OBJECTIVES: This study aimed to indicate the feasibility of a prototype electrical neuromodulation system using a closed-loop energy-efficient ultrasound-based mechanism for communication, data transmission, and recharging. MATERIALS AND METHODS: Closed-loop deep brain stimulation (DBS) prototypes were designed and fabricated with ultrasonic wideband (UsWB) communication technology and miniaturized custom electronics. Two devices were implanted short term in anesthetized Göttingen minipigs (N = 2). Targeting was performed using preoperative magnetic resonance imaging, and locations were confirmed postoperatively by computerized tomography. DBS systems were tested over a wide range of stimulation settings to mimic minimal, typical, and/or aggressive clinical settings, and evaluated for their ability to transmit data through scalp tissue and to recharge the DBS system using UsWB. RESULTS: Stimulation, communication, reprogramming, and recharging protocols were successfully achieved in both subjects for amplitude (1V-6V), frequency (50-250 Hz), and pulse width (60-200 µs) settings and maintained for ≥six hours. The precision of pulse settings was verified with <5% error. Communication rates of 64 kbit/s with an error rate of 0.05% were shown, with no meaningful throughput degradation observed. Time to recharge to 80% capacity was <9 minutes. Two DBS systems also were implanted in the second test animal, and independent bilateral stimulation was successfully shown. CONCLUSIONS: The system performed at clinically relevant implant depths and settings. Independent bilateral stimulation for the duration of the study with a 4F energy storage and full rapid recharge were achieved. Continuous function extrapolates to six days of continuous stimulation in future design iterations implementing application specific integrated circuit level efficiency and 15F storage capacitance. UsWB increases energy efficiency, reducing storage requirements and thereby enabling device miniaturization. The device can enable intelligent closed-loop stimulation, remote system monitoring, and optimization and can serve as a power/data gateway to interconnect the intrabody network with the Internet of Medical Things.

High shear induces platelet dysfunction leading to enhanced thrombotic propensity and diminished hemostatic capacity.

Thrombosis and bleeding are devastating adverse events in patients supported with blood-contacting medical devices (BCMDs). In this study, we delineated that high non-physiological shear stress (NPSS) caused platelet dysfunction that may contribute to both thrombosis and bleeding. Human blood was subjected to NPSS with short exposure time. Levels of platelet surface GPIbα and GPVI receptors as well as activation level of GPIIb/IIIa in NPSS-sheared blood were examined with flow cytometry. Adhesion of sheared platelets on fibrinogen, von Willibrand factor (VWF), and collagen was quantified with fluorescent microscopy. Ristocetin- and collagen-induced platelet aggregation was characterized by aggregometry. NPSS activated platelets in a shear and exposure time-dependent manner. The number of activated platelets increased with increasing levels of NPSS and exposure time, which corresponded well with increased adhesion of sheared platelets on fibrinogen. Concurrently, NPSS caused shedding of GPIbα and GPVI in a manner dependent on shear and exposure time. The loss of intact GPIbα and GPVI increased with increasing levels of NPSS and exposure time. The number of platelets adhered on VWF and collagen decreased with increasing levels of NPSS and exposure time, respectively. The decrease in the number of platelets adhered on VWF and collagen corresponded well with the loss in GPIbα and GPVI on platelet surface. Both ristocetin- and collagen-induced platelet aggregation in sheared blood decreased with increasing levels of NPSS and exposure time. The study clearly demonstrated that high NPSS causes simultaneous platelet activation and receptor shedding, resulting in a paradoxical effect on platelet function via two distinct mechanisms. The results from the study suggested that the NPSS could induce the concurrent propensity for both thrombosis and bleeding in patients.

Mechanistic insight of platelet apoptosis leading to non-surgical bleeding among heart failure patients supported by continuous-flow left ventricular assist devices.

Non-surgical bleeding (NSB) is the most common clinical complication in heart failure (HF) patients supported by continuous-flow left ventricular assist devices (CF-LVADs). In this study, oxidative stress and alteration of signal pathways leading to platelet apoptosis were investigated. Thirty-one HF patients supported by CF-LVADs were divided into bleeder (n = 12) and non-bleeder (n = 19) groups. Multiple blood samples were collected at pre-implant (baseline) and weekly up to 1-month post-implant. A single blood sample was collected from healthy subjects (reference). Production of reactive oxygen species (ROS) in platelets, total antioxidant capacity (TAC), oxidized low-density lipoproteins (oxLDL), expression of Bcl-2 and Bcl-xL, Bax and release of cytochrome c (Cyt.c), platelet mitochondrial membrane potential (Δψ m), activation of caspases, gelsolin cleavage and platelet apoptosis were examined. Significantly elevated ROS, oxLDL and depleted TAC were evident in the bleeder group compared to non-bleeder group (p < 0.05). Platelet pro-survival proteins (Bcl-2, Bcl-xL) were significantly reduced in the bleeder group in comparison to the non-bleeder group (p < 0.05). Translocation of Bax into platelet mitochondria membrane and subsequent release of Cyt.c were more prevalent in the bleeder group. Platelet mitochondrial damage, activation of caspases, gelsolin cleavage, and ultimate platelet apoptosis in the bleeder group were observed. Oxidative stress and activation of both intrinsic and extrinsic pathways of platelet apoptosis may be linked to NSB in CF-LVAD patients. Additionally, biomarkers of oxidative stress, examination of pro-survivals and pro-apoptotic proteins in platelets, mitochondrial damage, caspase activation, and platelet apoptosis may be used to help identify HF patients at high risk of NSB post-implant.

Electron Doping of Ultrathin Black Phosphorus with Cu Adatoms.

Few-layer black phosphorus is a monatomic two-dimensional crystal with a direct band gap that has high carrier mobility for both holes and electrons. Similarly to other layered atomic crystals, like graphene or layered transition metal dichalcogenides, the transport behavior of few-layer black phosphorus is sensitive to surface impurities, adsorbates, and adatoms. Here we study the effect of Cu adatoms onto few-layer black phosphorus by characterizing few-layer black phosphorus field effect devices and by performing first-principles calculations. We find that the addition of Cu adatoms can be used to controllably n-dope few layer black phosphorus, thereby lowering the threshold voltage for n-type conduction without degrading the transport properties. We demonstrate a scalable 2D material-based complementary inverter which utilizes a boron nitride gate dielectric, a graphite gate, and a single bP crystal for both the p- and n-channels. The inverter operates at matched input and output voltages, exhibits a gain of 46, and does not require different contact metals or local electrostatic gating.

Paradoxical Effect of Nonphysiological Shear Stress on Platelets and von Willebrand Factor.

Blood can become hypercoagulable by shear-induced platelet activation and generation of microparticles. It has been reported that nonphysiological shear stress (NPSS) could induce shedding of platelet receptor glycoprotein (GP) Ibα, which may result in an opposite effect to hemostasis. The aim of this study was to investigate the influence of the NPSS on platelets and von Willebrand factor (vWF). Human blood was exposed to two levels of NPSS (25 Pa, 125 Pa) with an exposure time of 0.5 s, generated by using a novel blood-shearing device. Platelet activation (P-selectin expression, GPIIb/IIIa activation and generation of microparticles) and shedding of three platelet receptors (GPIbα, GPVI, GPIIb/IIIa) in sheared blood were quantified using flow cytometry. Aggregation capacity of sheared blood induced by ristocetin and collagen was evaluated using an aggregometer. Shear-induced vWF damage was characterized with Western blotting. Consistent with the published data, the NPSS caused significantly more platelets to become activated with increasing NPSS level. Meanwhile, the NPSS induced the shedding of platelet receptors. The loss of the platelet receptors increased with increasing NPSS level. The aggregation capacity of sheared blood induced by ristocetin and collagen decreased. There was a loss of high molecular weight multimers (HMWMs) of vWF in sheared blood. These results suggest that the NPSS induced a paradoxical effect. More activated platelets increase the risk of thrombosis, while the reduction in platelet receptors and the loss of HMWM-vWF increased the propensity of bleeding. The finding might provide a new perspective to understand thrombosis and acquired bleeding disorder in patients supported with blood contacting medical devices.

Systemic Inflammatory Response Syndrome in End-Stage Heart Failure Patients Following Continuous-Flow Left Ventricular Assist Device Implantation: Differences in Plasma Redox Status and Leukocyte Activation.

The role of oxidative stress and leukocyte activation has not been elucidated in developing systemic inflammatory response syndrome (SIRS) in heart failure (HF) patients after continuous-flow left ventricular assist device (CF-LVAD) implantation. The objective of this study was to investigate the change of plasma redox status and leukocyte activation in CF-LVAD implanted HF patients with or without SIRS. We recruited 31 CF-LVAD implanted HF patients (16 SIRS and 15 non-SIRS) and 11 healthy volunteers as the control. Pre- and postimplant blood samples were collected from the HF patients. Plasma levels of oxidized low-density lipoprotein (oxLDL), malondialdehyde (MDA), total antioxidant capacity (TAC), superoxide dismutase (SOD) in erythrocyte, myeloperoxidase (MPO), and polymorphonuclear elastase (PMN-elastase) were measured. The HF patients had a preexisting condition of oxidative stress than healthy controls as evident from the higher oxLDL and MDA levels as well as depleted SOD and TAC. Leukocyte activation in terms of higher plasma MPO and PMN-elastase was also prominent in HF patients than controls. Persistent oxidative stress and reduced antioxidant status were found to be more belligerent in HF patients with SIRS after the implantation of CF-LVAD when compared with non-SIRS patients. Similar to oxidative stress, the activation of blood leukocyte was significantly highlighted in SIRS patients after implantation compared with non-SIRS. We identified that the plasma redox status and leukocyte activation became more prominent in CF-LVAD implanted HF patients who developed SIRS. Our findings suggest that plasma biomarkers of oxidative stress and leukocyte activation may be associated with the development of SIRS after CF-LVAD implant surgery.

Activation and shedding of platelet glycoprotein IIb/IIIa under non-physiological shear stress.

The purpose of this study was to investigate the influence of non-physiological high shear stress on activation and shedding of platelet GP IIb/IIIa receptors. The healthy donor blood was exposed to three levels of high shear stresses (25, 75, 125 Pa) from the physiological to non-physiological status with three short exposure time (0.05, 0.5, 1.5 s), created by a specific blood shearing system. The activation and shedding of the platelet GPIIb/IIIa were analyzed using flow cytometry and enzyme-linked immunosorbent assay. In addition, platelet P-selectin expression of sheared blood, which is a marker for activated platelets, was also analyzed. The results from the present study showed that the number of activated platelets, as indicated by the surface GPIIb/IIIa activation and P-selectin expression, increased with increasing the shear stress level and exposure time. However, the mean fluorescence of GPIIb/IIIa on the platelet surface, decreased with increasing the shear stress level and exposure time. The reduction of GPIIb/IIIa on the platelet surface was further proved by the reduction of further activated platelet GPIIb/IIIa surface expression induced by ADP and the increase in GPIIb/IIIa concentration in microparticle-free plasma with increasing the applied shear stress and exposure time. It is clear that non-physiological shear stress induce a paradoxical phenomenon, in which both activation and shedding of the GPIIb/IIIa on the platelet surface occur simultaneously. This study may offer a new perspective to explain the reason of both increased thrombosis and bleeding events in patients implanted with high shear blood-contacting medical devices.

Nanometer thick elastic graphene engine.

Significant progress has been made in the construction and theoretical understanding of molecular motors because of their potential use. Here, we have demonstrated fabrication of a simple but powerful 1 nm thick graphene engine. The engine comprises a high elastic membrane-piston made of graphene and weakly chemisorbed ClF3 molecules as the high power volume changeable actuator, while a 532 nm LASER acts as the ignition plug. Rapid volume expansion of the ClF3 molecules leads to graphene blisters. The size of the blister is controllable by changing the ignition parameters. The estimated internal pressure per expansion cycle of the engine is about ∼10(6) Pa. The graphene engine presented here shows exceptional reliability, showing no degradation after 10,000 cycles.

H2S protects against pressure overload-induced heart failure via upregulation of endothelial nitric oxide synthase.

BACKGROUND: Cystathionine γ-lyase (CSE) produces H2S via enzymatic conversion of L-cysteine and plays a critical role in cardiovascular homeostasis. We investigated the effects of genetic modulation of CSE and exogenous H2S therapy in the setting of pressure overload-induced heart failure. METHODS AND RESULTS: Transverse aortic constriction was performed in wild-type, CSE knockout, and cardiac-specific CSE transgenic mice. In addition, C57BL/6J or CSE knockout mice received a novel H2S donor (SG-1002). Mice were followed up for 12 weeks with echocardiography. We observed a >60% reduction in myocardial and circulating H2S levels after transverse aortic constriction. CSE knockout mice exhibited significantly greater cardiac dilatation and dysfunction than wild-type mice after transverse aortic constriction, and cardiac-specific CSE transgenic mice maintained cardiac structure and function after transverse aortic constriction. H2S therapy with SG-1002 resulted in cardioprotection during transverse aortic constriction via upregulation of the vascular endothelial growth factor-Akt-endothelial nitric oxide synthase-nitric oxide-cGMP pathway with preserved mitochondrial function, attenuated oxidative stress, and increased myocardial vascular density. CONCLUSIONS: Our results demonstrate that H2S levels are decreased in mice in the setting of heart failure. Moreover, CSE plays a critical role in the preservation of cardiac function in heart failure, and oral H2S therapy prevents the transition from compensated to decompensated heart failure in part via upregulation of endothelial nitric oxide synthase and increased nitric oxide bioavailability.

Anatomical and Hemodynamic Characterization of Totally Artificial Hearts.

We characterize the anatomy and function of never before studied total artificial hearts (TAHs) using established methods for testing mechanical circulatory support (MCS) devices. A historical review of TAHs is also presented to aid in benchmarking performance metrics. Six TAHs, ranging from spooky Halloween beating hearts to a cute colorful plush heart, were imaged, instrumented (mock flow loops) to measure their pressure, volume, and flow, and qualitatively evaluated by 3rd party cardiac surgeons for anatomical accuracy and surgical considerations. Imaging of Claw, Beating, and Frankenstein TAHs revealed internal motors, circuit boards, and speakers. Gummy TAH was ranked favorite TAH for tactile realism, while Frankenstein TAH had the most favorable audible/visual indicators, including an illuminated Jacob's Ladder. Beating TAH demonstrated superior pulsatile hemodynamic performance compared to Claw TAH (16mL vs 1.3mL stroke volume). Light Up TAH and Gummy TAH functioned only as passive compliance chambers. Cute TAH rapidly exsanguinated due to its porosity (-3.0 L/min flow). These TAHs demonstrated a wide range of anatomical accuracy, surgeon appeal, unique features, and hemodynamic performance. While Claw TAH and Beating TAH successfully generated a modicum of pulsatility, we recommend the clinical community continue to support pre-clinical development of emerging or use of clinically-approved TAHs.

Feasibility Testing of the Bionet Sonar Ultrasound Transcutaneous Energy Transmission (UTET) System for Wireless Power and Communication of a LVAD.

PURPOSE: To address the clinical need for totally implantable mechanical circulatory support devices, Bionet Sonar is developing a novel Ultrasonic Transcutaneous Energy Transmission (UTET) system that is designed to eliminate external power and/or data communication drivelines. METHODS: UTET systems were designed, fabricated, and pre-clinically tested using a non-clinical HeartWare HVAD in static and dynamic mock flow loop and acute animal models over a range of pump speeds (1800, 2400, 3000 RPM) and tissue analogue thicknesses (5, 10, 15 mm). RESULTS: The prototypes demonstrated feasibility as evidenced by meeting/exceeding function, operation, and performance metrics with no system failures, including achieving receiver (harvested) power exceeding HVAD power requirements and data communication rates of 10kB/s and pump speed control (> 95% sensitivity and specificity) for all experimental test conditions, and within healthy tissue temperature range with no acute tissue damage. CONCLUSION: During early-stage development and testing, engineering challenges for UTET size reduction and stable and safe operation were identified, with solutions and plans to address the limitations in future design iterations also presented.

Early-stage Development of the CoRISMA Mechanical Circulatory Support (CMCS) System for Heart Failure Therapy.

PURPOSE: CoRISMA MCS Systems Inc (Hamden CT) is developing an innovative mechanical circulatory support system (CMCS) as a durable therapeutic option for heart failure (HF) patients. The CMCS system is comprised of an axial flow pump, non-contacting hydrodynamic bearings, and integrated DC motor designed to be fully implantable in a left atrial (LA) to aortic (Ao) configuration; this unloading strategy may be particularly beneficial for HF patients with preserved ejection fraction (HFpEF). The small (5.5 cm3), lightweight (20 g), and low power (5-7 W) device design should allow for a less invasive off-pump implant. We present early-stage engineering development and testing of the prototype CoRISMA pumps. METHODS: Computational fluid dynamics (CFD) modeling was performed to evaluate flow and shear in two impeller (3 blades, 0.5 mm thickness, 8.9 mm diameter, 0.15 mm gap, polished titanium) and diffusor (5 blades, polished titanium) candidate designs. Test apparatuses were custom built to expedite development of the impeller/diffuser designs and iteratively refine the CFD models. Two candidate impeller/diffusor designs were fabricated and tested in each of the two test apparatuses (n = 4 impeller/diffuser + test fixture configurations) in static mock flow loops (hydrodynamic H-Q curves, 3.5 cP glycerol solution at 37 °C), and in dynamic mock flow loops (hemodynamics, 3.5 cP glycerol solution at 37 °C) tuned to HF conditions (mean aortic pressure 50 mmHg, central venous pressure 15 mmHg, aortic flow 3.0 L/min, and heart rate 80 bpm). RESULTS: CFD predicted flows of 4.56 L/min and 4.82 L/min at 100 mmHg for impellers/diffusers 1 and 2, respectively. Impeller 2 required less torque to generate a 6% increase in fluidic flow, and the diffuser had a larger area of high pressure, indicative of lower friction, which likely contributed to the increased efficiency. Experimental testing for all four configurations in the static and dynamic mock loops met performance metrics as evidenced by generating 4.0-4.5 L/min flow against 70-76 mmHg pressure at 25,000 rpm and restoring hemodynamics in the dynamic mock flow loop (MAP = 80 mmHg, CVP = 0 mmHg, total flow = 5.5 L/min) from baseline simulated HF test conditions. CONCLUSION: These results demonstrate proof-of-concept of the early engineering design and performance of the prototype CoRISMA pumps. Engineering specifications, challenges observed, and proposed solutions for the next design iteration were identified for the continued development of an effective, reliable, and safe LA-to-Ao CMCS system for HF patients. Current design plans are underway for incorporating a wireless energy transfer system for communication and power, eliminating the need for and complications associated with an external driveline, to achieve a fully-implantable system.

APPaRENT 3: Asthma Patients' and Physicians' Perspectives on the Burden and Management of Asthma in Seven Countries.

INTRODUCTION: Asthma management is strongly dependent on physician and patient beliefs and perceptions about the disease and its long-term treatment. The APPaRENT 3 study was conducted to explore factors influencing treatment choice and to understand patients' and physicians' attitudes and perspectives on the use of controller inhalers in regular versus flexible dosing for asthma management. METHODS: This cross-sectional survey of patients with asthma and treating physicians was conducted in seven countries: Indonesia, Malaysia, Philippines, Thailand, Vietnam (patient survey only), Saudi Arabia, and the United Arab Emirates. Assessment was carried out through an online/face-to-face questionnaire, where patients' viewpoints were focused on their attitudes and beliefs about asthma and treatment adherence, whereas physicians' viewpoints were gathered on their attitudes and beliefs about asthma management, knowledge of and adherence to asthma treatment guidelines, and asthma treatment regimens. RESULTS: Overall, 1400 patients (mean age, 34 years) and 599 physicians (mean age, 43 years) were included in the survey. Physicians similarly prioritised symptom control (39%) and exacerbation reduction (40%) in moderate asthma, whereas patients prioritised symptom control (41%) over exacerbation reduction (22%). Although both groups (physicians, 86%; patients, 84%) perceived asthma as well-controlled, poor management was evident based on Asthma Control Test (ACT) scores (mean, 15.7; standard deviation, 4.14; 82% had an ACT score < 20) and high symptom burden (39% reported nighttime awakenings or early mornings ≥ 2 nights/week). Most patients (76%) with moderate asthma were prescribed regular dosing, with the most common treatment being inhaled corticosteroid (ICS)/long-acting ß2-agonist (LABA) with as-needed inhaled short-acting ß2-agonist (SABA; 20%). Among patients on maintenance and reliever therapy, 93% of patients received a separate inhaled reliever. CONCLUSIONS: Despite high symptom burden, patients overestimated their level of asthma control. Physicians prioritised controlling symptoms and reducing exacerbations as treatment goals for moderate asthma, often prescribing regular dosing with ICS/LABA with as-needed inhaled SABA.

Managing asthma depends a lot on what doctors and patients think about the illness and its long-term treatment. This study looked into what influences treatment decisions and what patients and doctors think about using inhalers regularly or on an as-needed basis to manage asthma across seven countries (Indonesia, Malaysia, Philippines, Thailand, Vietnam [patient survey only], Saudi Arabia, and the United Arab Emirates). In this study, patients with asthma and doctors managing asthma completed an online/face-to-face questionnaire. The study aimed to understand what patients think about asthma and their treatment plan. Meanwhile, the doctors were asked what they think about managing asthma and how much they apply clinical guidelines for treating patients with asthma. Doctors believed it is equally important to control symptoms and prevent worsening of symptoms in patients with moderate asthma, while patients cared more about controlling symptoms than preventing worsening of symptoms. While doctors and patients both regarded asthma as well-controlled, many patients had low Asthma Control Test scores and experienced a lot of symptoms, suggesting that they are poor perceivers of asthma control. Most patients with moderate asthma were given regular treatment, usually with inhaled corticosteroid combined with long-acting ß₂-agonist along with as-needed short-acting ß₂-agonist as a reliever. Most patients who were prescribed the same inhaler for regular use and as a reliever also had a separate inhaler for quick relief of symptoms. This study shows the need for patients and doctors to have better conversations about asthma, its treatments, and what to expect from them.

Integrating molecular and clinical variables to predict myocardial recovery.

Mechanical unloading and circulatory support with left ventricular assist devices (LVADs) mediate significant myocardial improvement in a subset of advanced heart failure (HF) patients. The clinical and biological phenomena associated with cardiac recovery are under intensive investigation. Left ventricular (LV) apical tissue, alongside clinical data, were collected from HF patients at the time of LVAD implantation (n=208). RNA was isolated and mRNA transcripts were identified through RNA sequencing and confirmed with RT-qPCR. To our knowledge this is the first study to combine transcriptomic and clinical data to derive predictors of myocardial recovery. We used a bioinformatic approach to integrate 59 clinical variables and 22,373 mRNA transcripts at the time of LVAD implantation for the prediction of post-LVAD myocardial recovery defined as LV ejection fraction (LVEF) ≥40% and LV end-diastolic diameter (LVEDD) ≤5.9cm, as well as functional and structural LV improvement independently by using LVEF and LVEDD as continuous variables, respectively. To substantiate the predicted variables, we used a multi-model approach with logistic and linear regressions. Combining RNA and clinical data resulted in a gradient boosted model with 80 features achieving an AUC of 0.731±0.15 for predicting myocardial recovery. Variables associated with myocardial recovery from a clinical standpoint included HF duration, pre-LVAD LVEF, LVEDD, and HF pharmacologic therapy, and LRRN4CL (ligand binding and programmed cell death) from a biological standpoint. Our findings could have diagnostic, prognostic, and therapeutic implications for advanced HF patients, and inform the care of the broader HF population.

Extracorporeal membrane oxygenation versus counterpulsatile, pulsatile, and continuous left ventricular unloading for pediatric mechanical circulatory support.

OBJECTIVES: Despite progress with adult ventricular assist devices, limited options exist to support pediatric patients with life-threatening heart disease. Extracorporeal membrane oxygenation remains the clinical standard. To characterize (patho)physiologic responses to different modes of mechanical unloading of the failing pediatric heart, extracorporeal membrane oxygenation was compared to intra-aortic balloon pump, pulsatile-flow ventricular assist device, or continuous-flow ventricular assist device support in a pediatric heart failure model. DESIGN: Experimental. SETTING: Large animal laboratory operating room. SUBJECTS: Yorkshire piglets (n = 47; 11.7 ± 2.6 kg). INTERVENTIONS: In piglets with coronary ligation-induced cardiac dysfunction, mechanical circulatory support devices were implanted and studied during maximum support. MEASUREMENTS AND MAIN RESULTS: Left ventricular, right ventricular, coronary, carotid, systemic arterial, and pulmonary arterial hemodynamics were measured with pressure and flow transducers. Myocardial oxygen consumption and total-body oxygen consumption were calculated from arterial, venous, and coronary sinus blood sampling. Blood flow was measured in 17 organs with microspheres. Paired Student t tests compared baseline and heart failure conditions. One-way repeated-measures analysis of variance compared heart failure, device support mode(s), and extracorporeal membrane oxygenation. Statistically significant (p < 0.05) findings included 1) an improved left ventricular blood supply/demand ratio during pulsatile-flow ventricular assist device, continuous-flow ventricular assist device, and extracorporeal membrane oxygenation but not intra-aortic balloon pump support, 2) an improved global myocardial blood supply/demand ratio during pulsatile-flow ventricular assist device and continuous-flow ventricular assist device but not intra-aortic balloon pump or extracorporeal membrane oxygenation support, and 3) diminished pulsatility during extracorporeal membrane oxygenation and continuous-flow ventricular assist device but not intra-aortic balloon pump and pulsatile-flow ventricular assist device support. A profile of systems-based responses was established for each type of support. CONCLUSIONS: Each type of pediatric ventricular assist device provided hemodynamic support by unloading the heart with a different mechanism that created a unique profile of physiological changes. These data contribute novel, clinically relevant insight into pediatric mechanical circulatory support and establish an important resource for pediatric device development and patient selection.

Bovine model of chronic ischemic cardiomyopathy: implications for ventricular assist device research.

Ventricular assist devices (VADs) have emerged as a successful treatment option for advanced heart failure. The objective of this study was to develop a clinically relevant model of chronic ischemic cardiomyopathy to investigate functional, histological, and molecular changes during mechanical circulatory support. In calves (n = 17, 94 ± 7 kg), 90 µm microspheres were injected percutaneously into the left coronary artery. Serial echocardiography was performed weekly to evaluate cardiac function. Sixty days after coronary microembolization, a terminal study was performed via thoracotomy to measure hemodynamics. Regional myocardial and end-organ blood flows were quantified with 15-µm fluorescent-labeled microspheres. Myocardial fibrosis, myocyte size, and myocardial apoptosis were quantified with histological stains. Eleven animals survived coronary microembolization and exhibited clinical and statistically significant echocardiographic and hemodynamic signs of severe systolic dysfunction. Statistically significant decreases in regional myocardial blood flow and increases in myocardial fibrosis, myocyte size, total myocardial apoptosis, and cardiac myocyte-specific apoptosis were observed. End-organ hypoperfusion was observed. Coronary microembolization induced stable and reproducible chronic left ventricular failure in calves. The anatomical size and physiology of the bovine heart and thorax are appropriate to study novel interventions for the clinical management of heart failure. This model is an appropriate physiological substrate in which to test VAD and adjunctive biological therapies.

Ultrathin oxide films by atomic layer deposition on graphene.

In this paper, a method is presented to create and characterize mechanically robust, free-standing, ultrathin, oxide films with controlled, nanometer-scale thickness using atomic layer deposition (ALD) on graphene. Aluminum oxide films were deposited onto suspended graphene membranes using ALD. Subsequent etching of the graphene left pure aluminum oxide films only a few atoms in thickness. A pressurized blister test was used to determine that these ultrathin films have a Young's modulus of 154 ± 13 GPa. This Young's modulus is comparable to much thicker alumina ALD films. This behavior indicates that these ultrathin two-dimensional films have excellent mechanical integrity. The films are also impermeable to standard gases suggesting they are pinhole-free. These continuous ultrathin films are expected to enable new applications in fields such as thin film coatings, membranes, and flexible electronics.

Feasibility Testing of the RT Cardiac Systems Percutaneous Mechanical Circulatory Support Device.

RT Cardiac Systems (RTCS, Raleigh, NC) is developing an intravascular percutaneous mechanical circulatory support (pMCS) device drive system for use during high-risk percutaneous coronary intervention and emergent cardiogenic shock. The proprietary pMCS device (US patent 10,780,206) consists of a miniaturized axial flow pump with an integrated motor connected via a short flexible drive system. This novel flexible drive system creates a flexible pump that is advantageous for percutaneous placement and conforming to anatomy. This design also has the benefit of not requiring a continuous external lubrication source. In this article, we present engineering development and feasibility testing of the prototype pMCS system. Computational fluid dynamics (CFD) modeling was performed to evaluate candidate blade set designs (impeller leading and trailing edges, diffuser) and predict hydrodynamic performance and hemolysis risk. Bench testing of candidate lip seal designs (radial interference, durometer, and seal angle) was evaluated for leak rate. Two 16Fr prototype devices were then fabricated and tested in a static mock flow loop. Experimental testing demonstrated 3 L/min flow against 110 mmHg and 4 L/min flow against 80 mmHg, which matched the CFD-predicted hydrodynamic performance. These results demonstrate feasibility of the engineering design and performance of the prototype devices.