Modeling and design of solar + storage-powered community resilience hubs across California.

Distributed clean, reliable energy resources like solar plus battery storage (solar + storage) can reduce harmful emissions while supporting resilience. Solar + storage-powered resilience hubs provide energy for critical services during disasters while increasing human adaptive capacity year round. We studied where utility rates, local climate, and historical injustice make solar + storage resilience hubs more valuable and more challenging. We modeled the economic and climate impacts of outfitting candidate hub sites across California with solar + storage for everyday operations and identified designs and costs required to withstand a range of outages considering weather impacts on energy needs and availability. We integrated sociodemographic data to prioritize the siting of resilience hubs, to focus potential policy and funding priorities on regions where solar + storage for resilience hubs is hard or expensive, and where populations are most in need. We identified almost 20,000 candidate buildings with more than 8 GW of total rooftop solar potential capable of reducing CO2 emissions by 5 million tons per year while providing energy for community resilience. Hub capacity for one of the most challenging missions-providing emergency shelter during a power outage and smoke event-could have a statewide average lifetime cost of less than $2000 per seat. We identified regional challenges including insufficient rooftop solar capacity in cities, low sunlight in northern coastal California, and high costs driven by utility rate structures in Sacramento and the Imperial Valley. Results show that rates and net metering rules that incentivize solar + storage during everyday operations decrease resilience costs.

Mechanical loading influences the effects of bisphosphonates on human periodontal ligament fibroblasts.

OBJECTIVES: There is increasing evidence that bisphosphonates affect orthodontic tooth movement. The object of the study was to investigate the changes produced by tensile strain on human periodontal ligament fibroblasts (HPdLFs) treated with clodronate or zoledronate. MATERIALS AND METHODS: HPdLF were cultured with 5 and 50 µM clodronate or zoledronate for 48 h and applied to tensile strain (TS) (5 and 10 %) for 12 h in vitro. Viability was verified by MTT assay and apoptosis rate via caspase 3/7 assay. Gene expression of receptor activator of nuclear factor kappa-B ligand (RANKL) and osteoprotegerin (OPG) was investigated using real-time PCR. OPG was also analyzed by ELISA and RANKL by immunocytochemical staining. RESULTS: Zoledronate (50 µM) reduced the viability of HPdLF (76 vs 100 %) and combined with 5 % TS to 53 %. TS of 10 % and clodronate reduced viability to 79 % with increased caspase 3/7 activity. Clodronate (5 µM) led to a slight increase of OPG gene expression, zoledronate (5 µM) to a slight decrease. Combined with 5 % TS, both increased OPG gene expression (2-3-fold) and OPG synthesis. Zoledronate increased gene expression of RANKL (4-fold). Combined with 5 % of TS, this increase was abolished. TS of 10 % in combination amplified increase of RANKL ending up with a 9-fold gene expression by clodronate and high RANKL protein synthesis. CONCLUSIONS: This study shows for the first time that mechanical loading alters the effects of bisphosphonates on viability, apoptosis rate, and OPG/RANKL system of HPdLF dependent on the applied strength. Low forces and bisphosphonates increase factors for bone apposition, whereas high forces combined with bisphosphonates stimulate osteoclastogenesis. CLINICAL RELEVANCE: Mechanical loading of periodontal ligament with high strengths should be avoided during bisphosphonate therapy.

Induction of IL-6 and MMP-8 in human periodontal fibroblasts by static tensile strain.

OBJECTIVES: Mechanical loading is a potential activator of inflammation and able to stimulate factors for periodontal and alveolar bone destruction. Aim of this study was to investigate the inflammatory response and synthesis of proteinases by human periodontal ligament fibroblast (HPdLF) dependent on different strengths of static tensile strain (STS). MATERIALS AND METHODS: HPdLFs were loaded with different STS strengths (1, 5, and 10 %) in vitro. Gene expressions of cyclooxygenase (COX)-2 and interleukin (IL)-6 were analyzed by quantitative real-time polymerase chain reaction. Production of IL-6, prostaglandin E2 (PGE2), matrix metalloproteinase (MMP)-8, and tissue inhibitors of matrix metalloproteinase (TIMP)-1 were measured by enzyme-linked immunosorbent assay. Receptor activator of nuclear factor-kappa ligand (RANKL) synthesis was detected by immunocytochemical staining. RESULTS: Ten percent STS led to an increased gene expression of IL-6 and COX-2 (34.4-fold) in HPdLF, and 1 and 5 % STS slightly reduced the gene expression of IL-6. Synthesis of IL-6 was significantly reduced by 1 % STS and stimulated by 10 % STS. Ten percent STS significantly induced PGE2 production. RANKL was not detectable at any strength of STS. MMP-8 synthesis showed significantly higher values only at 10 % STS, but TIMP-1 was stimulated by 5 and 10 % STS, resulting into highest TIMP-1/MMP-8 ratio at 5 % STS. CONCLUSIONS: High-strength STS is a potent inducer of periodontal inflammation and MMP-8, whereas low-strength STS shows an anti-inflammatory effect. Moderate-strength STS causes the highest TIMP-1/MMP-8 ratio, leading to appropriate conditions for reformation of the extracellular matrix. CLINICAL RELEVANCE: Furthermore, this study points out that the strength of force plays a pivotal role to achieve orthodontic tooth movement without inducing periodontal inflammation and to activate extracellular matrix regeneration.

An environmental justice analysis of air pollution emissions in the United States from 1970 to 2010.

Over the last decades, air pollution emissions have decreased substantially; however, inequities in air pollution persist. We evaluate county-level racial/ethnic and socioeconomic disparities in emissions changes from six air pollution source sectors (industry [SO2], energy [SO2, NOx], agriculture [NH3], commercial [NOx], residential [particulate organic carbon], and on-road transportation [NOx]) in the contiguous United States during the 40 years following the Clean Air Act (CAA) enactment (1970-2010). We calculate relative emission changes and examine the differential changes given county demographics using hierarchical nested models. The results show racial/ethnic disparities, particularly in the industry and energy generation source sectors. We also find that median family income is a driver of variation in relative emissions changes in all sectors-counties with median family income >$75 K vs. less generally experience larger relative declines in industry, energy, transportation, residential, and commercial-related emissions. Emissions from most air pollution source sectors have, on a national level, decreased following the United States CAA. In this work, we show that the relative reductions in emissions varied across racial/ethnic and socioeconomic groups.

Interradicular trabecular bone density of the lateral maxilla for temporary anchorage devices--a histomorphometric study.

OBJECTIVE: To analyze the interradicular trabecular bone density of the lateral maxilla regarding the insertion of temporary anchorage devices (TADs). MATERIAL AND METHODS: The material consisted of tissue blocks of autopsy material from 20 subjects (17 male, 3 female, 16 - 63y). The specimens comprised the dentated alveolar bone of the lateral maxilla. The interradicular areas (IRA) from canine to distally of the second molar (IRA 3-4, 4-5, 5-6, 6-7, 7d) were histomorphometrically measured with respect to the hard tissue fraction of the trabecular bone (HTFTB, %) and statistically analyzed. RESULTS: Histomorphometric measurements showed the following results: Mean HTFTB of IRA 3-4 was 44.08%, of IRA 4-5 31.07%, of IRA 5-6 33.96%, of IRA 6-7 36.33% and of IRA 7d 25.40%. Only the difference between the HTFTB of IRA 3-4 and the other IRAs was statistically significant (p < 0.05). Regarding the minimum and maximum HTFTB value of each IRA, there was a great amount of difference, especially for IRA 3-4: minimum HTFTB was 17.20% and maximum 67.03%. CONCLUSION: Apart from the IRA between canine and first premolar, the HTFTB in the IRAs of the lateral maxilla have to be classified as low or even moderate. IRA 3-4 should also be considered cautious regarding its minimum values. Thus, it seems that the interradicular trabecular bone density of the lateral maxilla is unfavorable to achieve a good primary stability of TADs.

One palatal implant for skeletal anchorage--frequency and range of indications.

OBJECTIVE: Aim of this investigation was to analyze the frequency and range of indications of orthodontic treatments using one palatal implant for skeletal anchorage, in a time frame of four years. MATERIAL AND METHODS: A sample was comprised by viewing retrospectively the patient collective of a specialized university clinic who started orthodontic treatment in the time frame 01/09-12/12. Inclusion criterion was the first application of a superstructure within the investigated period after successful insertion of a palatal implant (Ortho-System®, Straumann, Basel, Switzerland). Frequency and range of indications of the conducted skeletally anchored tooth movement were determined by analyzing the individual patient documentation such as medical records, radiographs and casts. RESULTS: From a total of 1350 patients who started orthodontic treatment in this period met 56 (=4.2%) the inclusion criterion. In 85.7% of this sample was sagittal orthodontic tooth movement conducted, most frequently mesialization of ≥1 tooth (44.6%). Vertical tooth movement was in 57.1% of the sample performed, mostly extrusion of ≥1 tooth (34%). In 33.9% of the sample was ≥1 displaced tooth orthodontically relocated. One or two upper incisors were in 16.1% of the sample permanently replaced by the superstructure, all but one even after orthodontic treatment. In 66.1% of all cases were multi-functional anchorage challenges performed. CONCLUSION: 4.2 % of all treated patients within the investigated period required orthodontic treatment with skeletal anchorage (palatal implant), mainly for performing sagittal tooth movement (mesialization). The palatal implant was primarily used for multi-functional anchorage purposes, including skeletally anchored treatment in the mandible.

Age-related changes of fibroblast density in the human periodontal ligament.

OBJECTIVE: Recently, research has focused intensely on age-related tissue changes, not only in the field of dermatology but also in dental sciences. Although many new insights into age-related morphological, ultrastructural and biochemical changes in the periodontal ligament tissue have been gained, the basic question of whether there is a quantitative change in cell number remains unanswered or, at least to date, unpublished. Thus, the aim of this study was to detect age-related changes of the periodontal ligament regarding fibroblast density. MATERIAL AND METHODS: 33 lateral tooth-bearing segments of the maxilla were obtained from deceased human individuals of different age, ranging from 7 to 63 years. The buccal segment of the periodontal ligament of the mesiobuccal root of the first maxillary molar was evaluated histomorphometrically to obtain the fibroblast density. RESULTS: The results clearly indicate a steady and statistically significant decline of fibroblast number with age. CONCLUSION: It may be concluded that fibroblast density in the physiological human periodontal ligament tissue decreases with age, thus causing an initial delay in physiological, pathological or externally induced processes that require remodeling of the periodontal ligament, e.g. traumatic occlusion or orthodontic tooth movement. It may be assumed that an orthodontic tooth movement in elderly patients requires more time in the initial treatment phase and should be done with lighter forces.

Current state of orthodontic patients under bisphosphonate therapy.

BACKGROUND: Bisphosphonates are a common medication for the prevention and therapy of osteoporosis, but are also applied for tumor diseases. They affect bone metabolism, and therefore also orthodontic treatments, but how it does has yet not been definitively clarified. Therefore, the aim of this research was to evaluate and demonstrate the reported effects and the current state of scientific research regarding orthodontic treatment and bisphosphonate medication exclusively in humans. MATERIAL AND METHODS: A systematic research of the literature for selected keywords in the Medline database (Pubmed) as well as a manual search was conducted. The following search terms were used: 'Bisphosphonate' in combination with: orthodontic, orthodontic treatment, tooth movement. FINDINGS: To date, only nine reported patients (case reports/series) and one original article (retrospective cohort study) regarding orthodontic treatment under bisphosphonate medication in humans have been published. Decelerated tooth movement with increased side effects (especially in high-risk patients) and longer treatment duration was reported in some articles. Patients with initial spacing or extraction cases had a higher risk of incomplete space closure and poor root parallelism. CONCLUSIONS: Orthodontic tooth movement under bisphosphonate medication is possible, especially in low-risk patients (low dose and short period of intake). But the treatment is still not predictable, especially in high-risk patients. Therefore, the altered bone metabolism and higher extent of side effects should be considered in treatment planning, especially in extraction cases or high-risk patients. Regardless, longer treatment duration, decelerated tooth movement, and more side effects, e.g., incomplete space closure and poor root parallelism, should be expected, especially in extraction cases or space closure.

[Orthodontic treatment of patients medicated with bisphosphonates-a clinical case report].

INTRODUCTION: Bisphosphonates (BP) are an established medication, e.g., for the prevention/therapy of osteoporosis. The effects of the changed bone metabolism for orthodontic treatments are unknown. CASE REPORT: A 66-year-old woman underwent a total oral rehabilitation. The therapy included (1) tooth extractions, (2) periodontal treatment, (3) insertion of dental implants, (4) provisional implant restorations, (5) orthodontic treatment, and (6) definite implant restorations. The orthodontic tooth movements were in- and retrusion of the upper frontal teeth, intrusion of the lower front teeth, using the dental implants as skeletal anchorage. After implant insertion and one month before beginning the orthodontic treatment, osteoporosis was diagnosed in this patient and, without notification to our facility, BP treatment was initiated by her general practitioner (alendronate oral, 70 mg/week), with an overall duration of intake of 7 months. After 13 months, the orthodontic treatment was successfully accomplished; however enlarged periodontal gaps, sclerotic bone areas, and mild apical root resorptions of the upper frontal teeth were found in this patient. CONCLUSION: Currently, there are no recommendations for orthodontic patients undergoing BP therapy. Orthodontic tooth movement in this low-risk patient with a short duration of intake and a low-dose BP medication was possible. Because of the reduced bone metabolism and the higher amount of side effects, the treatment should be performed with extremely light forces and frequent monitoring.

Apical root resorption during orthodontic treatment with aligners? A retrospective radiometric study.

INTRODUCTION: Objective of this study was to investigate the incidence and severity of apical root resorptions (ARR) during orthodontic treatment with aligners. MATERIALS AND METHODS: The sample comprised 100 patients (17-75 years of age) with a class I occlusion and anterior crowding before treatment, treated exclusively with aligners (Invisalign®, Align Technologies, Santa Clara, CA, USA). The following teeth were assessed: upper and lower anterior teeth and first molars. Root and crown lengths of a total of 1600 teeth were measured twice in pre- and post-treatment panoramic radiographs. Afterwards, relative changes of the root length during treatment were calculated by a root-crown-ratio taking pre- and post-treatment root and crown lengths into consideration. A reduction of this ratio was considered as a shortening of the initial root length. Additionally, tooth movements of the front teeth were assessed by lateral cephalograms and the 3-dimensonal set up of each patient. RESULTS: All patients had a reduction of the pre-treatment root length with a minimum of two teeth. On average 7.36 teeth per patient were affected. 54% of 1600 measured teeth showed no measurable root reduction. A reduction of >0%-10% of the pre-treatment root length was found in 27.75%, a distinct reduction of >10%-20% in 11.94%. 6.31% of all teeth were affected with a considerable reduction of >20%. We found no statistically significant correlation between relative root length changes and the individual tooth, gender, age or sagittal and vertical orthodontic tooth movement; except for extrusion of upper front teeth, which was considered as not clinical relevant due to the small amount of mean 4% ARR. CONCLUSIONS: The present study is the first analyzing ARR in patients with a fully implemented orthodontic treatment with aligners (i.e. resolving anterior crowding). The variety was high and no clinical relevant influence factor could be detected. A minimum of two teeth with a root length reduction was found in every patient. On average, 7.36 teeth per patient were affected.

A combined prosthodontic and orthodontic treatment approach in a case of growth inhibition induced by dental implants: a case report.

Functional and esthetic results can improve significantly when a combined prosthodontic-orthodontic treatment approach is employed in cases requiring extensive oral rehabilitation. The patient presented in this case report was treated in his late teens with dental implants as a replacement for his maxillary incisors. Ten years later, the entire maxillary anterior segment was in infraocclusion compared to the rest of the dentition and lip line. Since prosthodontic follow-up treatment alone could not achieve an optimal functional and esthetic outcome, the patient was treated orthodontically prior to renewing the restoration. A fixed appliance was used to intrude the mandibular anterior teeth as well as vertically align the infrapositioned maxillary lateral incisors.

Dental compensation for moderate Class III with vertical growth pattern by extraction of the lower second molars.

OBJECTIVES: Analysis of the effects and side effects of treatment of patients with moderate skeletal Class III and vertical growth pattern by means of extraction of the second molars in the lower jaw. PATIENTS AND METHODS: A total of 20 patients with a mean age of 12.9 years were examined retrospectively. Inclusion criteria consisted of a Wits value of 0 to -5, a posterior growth pattern of the mandible (Hasund analysis), an overjet of -2 to 1 mm, and an overbite of 0 to -3 mm. Treatment was performed using a straight-wire appliance. As part of the treatment, the lower second molars were extracted and Class III elastics attached. Cephalograms and orthopantomograms taken before and after treatment were used for evaluation. RESULTS: Treatment resulted in a significant change in the mean overjet from 0.5 mm to 2.1 mm and the attainment of a positive mean overbite of -1.0 mm to 0.9 mm. The occlusal plane rotated anteriorly from 18.8° to 13.7°. The skeletal parameters showed a change in the Wits value from -3.3 mm to -1.4 mm and an anterior mandibular rotation (ML-NSL 35.5° vs. 32.0°). The soft tissues revealed an increase in the distance between the lower lip and the "esthetic line" to the posterior (-2.0 mm vs. -3.9 mm). CONCLUSION: Dental compensation of moderate skeletal Class III with a tendency to an anterior open bite with vertical growth pattern by extracting the lower second molars, combined with Class III elastics, resulted in an anterior rotation of the occlusal plane and mandible. Eighteen of 20 patients achieved a physiological overjet and positive overbite. A prerequisite for this therapy is the presence of lower wisdom teeth; a potential side effect is elongation of the upper second molars.

Invisalign® treatment in the anterior region: were the predicted tooth movements achieved?

OBJECTIVE: Based on our previous pilot study, the objective of this extended study was to compare (a) casts to their corresponding digital ClinCheck® models at baseline and (b) the tooth movement achieved at the end of aligner therapy (Invisalign®) to the predicted movement in the anterior region. MATERIALS AND METHODS: Pre- and post-treatment casts as well as initial and final ClinChecks® models of 50 patients (15-63 years of age) were analyzed. All patients were treated with Invisalign® (Align Technology, Santa Clara, CA, USA). Evaluated parameters were: upper/lower anterior arch length and intercanine distance, overjet, overbite, dental midline shift, and the irregularity index according to Little. The comparison achieved/predicted tooth movement was tested for equivalence [adjusted 98.57% confidence interval (- 1.00; + 1.00)]. RESULTS: Before treatment the anterior crowding, according to Little, was on average 5.39 mm (minimum 1.50 mm, maximum 14.50 mm) in the upper dentition and 5.96 mm (minimum 2.00 mm, maximum 11.50 mm) in the lower dentition. After treatment the values were reduced to 1.57 mm (minimum 0 mm, maximum 4.5 mm) in the maxilla and 0.82 mm (minimum 0 mm, maximum 2.50 mm) in the mandible. We found slight deviations between pretreatment casts and initialClinCheck® ranging on average from -0.08 mm (SD ± 0.29) for the overjet and up to -0.28 mm (SD ± 0.46) for the upper anterior arch length. The difference between achieved/predicted tooth movements ranged on average from 0.01 mm (SD ± 0.48) for the lower anterior arch length, up to 0.7 mm (SD ± 0.87) for the overbite. All parameters were significantly equivalent except for the overbite (-1.02; -0.39). CONCLUSION: Performed with aligners (Invisalign®), the resolvement of the partly severe anterior crowding was successfully accomplished. Resolving lower anterior crowding by protrusion of the anterior teeth (i.e., enlargement of the anterior arch length) seems well predictable. The initial ClinCheck® models provided high accuracy compared to the initial casts. The achieved tooth movement was in concordance with the predicted movement for all parameters, except for the overbite.

Accuracy of Invisalign® treatments in the anterior tooth region. First results.

AIM: To analyse (a) to what extent the pretreatment model at the beginning of the treatment corresponds to the initial position in the ClinCheck® and (b) to what extent the predicted treatment result corresponds to the actual result of the therapy at the end of the treatment. MATERIAL AND METHODS: Pre- and posttreatment models as well as the initial and final position of the ClinCheck with a total of 35 patients aged between 15 and 59 were measured; all of whom were treated by using the Invisalign® technology (Invisalign®, Align Technology, S.C., Calif., USA). The measurement of the initial and final models was conducted by using an electronic digital calliper rule, i.e. that of ClinCheck® using the measurement tool ToothMeasure® of Invisalign® Software. The following parameters in the anterior region were measured: Overjet, Overbite, dental midline shift. RESULTS: Pretreament models and the initial ClinChecks® revealed slight deviations in the parameters overjet 0.08 mm (standard deviation (SD) 0.3), overbite 0.3 mm (SD 0.4) and dental midline deviation 0.1mm (SD 0.4). The final model and the final ClinCheck® revealed larger deviations: the differences for the Overjet were on average 0.4 mm (SD 0.7), Overbite 0.9 mm (SD 0.9) and dental midline shift 0.4 mm (SD 0.5). CONCLUSIONS: The IT-based transmission of mal-aligned teeth into the ClinCheck® presentation provides sufficiently good accuracy. Tooth corrections in the vertical plane were more difficult to realize. A vertical overcorrection in the final ClinCheck®, a case refinement at the end of the treatment or additional measures (e.g. horizontal beveled attachments or vertical elastics) seems useful to achieve the individually intended therapeutic goal.

Abordagem de tratamento protética e ortodôntica combinada no caso de inibição do crescimento induzida por implantes dentários: relato de caso clínico / A combined prosthodontic and orthodontic treatment approach in a case of growth inhibition induced by dental implants: a case report

Resultados estéticos e funcionais podem ser melhorados significativamente quando uma abordagem de tratamento protética e ortodôntica combinada é usada em casos que necessitam de reabilitação oral extensa. Este paciente apresentado neste relato de caso foi tratado no final de sua adolescência com implantes dentários para reposição dos incisivos superiores. Dez anos depois, todo o segmento anterior da maxila estava em infraoclusão comparado ao resto da dentição e da linha labial. Já que o acompanhamento protético em si não poderia alcançar um resultado funcional e estético adequado, a paciente foi tratada ortodonticamente antes de trocar a restauração. Um aparelho fixo foi usado para intruir os dentes anteriores inferiores e alinhar verticalmente os incisivos laterais superiores que estavam em infraposição