Copper Oxide Electrochemical Deposition to Create Antiviral and Antibacterial Nanocoatings.

The impact of the reaction environment on the formation of the polycrystalline layer and its biomedical (antimicrobial) applications were analyzed in detail. Copper oxide layers were synthesized using an electrodeposition technique, with varying additives influencing the morphology, thickness, and chemical composition. Scanning electron microscopy (SEM) images confirmed the successful formation of polyhedral structures. Unmodified samples (CuL) crystallized as a mixture of copper oxide (I) and (II), with a thickness of approximately 1.74 µm. The inclusion of the nonconductive polymer polyvinylpyrrolidone (PVP) during synthesis led to a regular and compact CuO-rich structure (CuL-PVP). Conversely, adding glucose resulted in forming a Cu2O-rich nanostructured layer (CuL-D(+)G). Both additives significantly reduced the sample thickness to 617 nm for CuL-PVP and 560 nm for CuL-D(+)G. The effectiveness of the synthesized copper oxide layers was demonstrated in their ability to significantly reduce the T4 phage titer by approximately 2.5-3 log. Notably, CuL-PVP and CuL-D(+)G showed a more substantial reduction in the MS2 phage titer, achieving about a 5-log decrease. In terms of antibacterial activity, CuL and CuL-PVP exhibited moderate efficacy against Escherichia coli, whereas CuL-D(+)G reduced the E. coli titer to undetectable levels. All samples induced similar reductions in Staphylococcus aureus titer. The study revealed differential susceptibilities, with Gram-negative bacteria being more vulnerable to CuL-D(+)G due to its unique composition and morphology. The antimicrobial properties were attributed to the redox cycling of Cu ions, which generate ROS, and the mechanical damage caused by nanostructured surfaces. A crucial finding was the impact of surface composition rather than surface morphology on antimicrobial efficacy. Samples with a dominant Cu2O composition exhibited potent antibacterial and antiviral properties, whereas CuO-rich materials showed predominantly enhanced antiviral activity. This research highlights the significance of phase composition in determining the antimicrobial properties of copper oxide layers synthesized through electrodeposition.

Comparative Study of Polymer-Modified Copper Oxide Electrochemical Sensors: Stability and Performance Analysis.

The effectiveness of copper oxide-modified electrochemical sensors using different polymers is being studied. The commercial powder was sonicated in an isopropyl alcohol solution and distilled water with 5 wt% polymers (chitosan, Nafion, PVP, HPC, α-terpineol). It was observed that the chitosan and Nafion caused degradation of CuO, but Nafion formed a stable mixture when diluted. The modified electrodes were drop-casted and analyzed using cyclic voltammetry in 0.1 M KCl + 3 mM [Fe(CN)6]3-/4- solution to determine the electrochemically active surface area (EASA). The results showed that α-terpineol formed agglomerates, while HPC created uneven distributions, resulting in poor stability. On the other hand, Nafion and PVP formed homogeneous layers, with PVP showing the highest EASA of 0.317 cm2. In phosphate-buffered saline (PBS), HPC and PVP demonstrated stable signals. Nafion remained the most stable in various electrolytes, making it suitable for sensing applications. Testing in 0.1 M NaOH revealed HPC instability, partial dissolution of PVP, and Cu ion reduction. The type of polymer used significantly impacts the performance of CuO sensors. Nafion and PVP show the most promise due to their stability and effective dispersion of CuO. Further optimization of polymer-CuO combinations is necessary for enhanced sensor functionality.

Unraveling the Impact of Adsorbed Molecules on Photocatalytic Processes: Advancements in Understanding Facet-Controlled Semiconductor Photocatalysts.

This work aims to demonstrate that the Fe2O3 nanocrystals' adsorptive and photocatalytic properties can be adjusted by exposing the crystal facets that are functionalized. To this end, cube- and disc-like structures were synthesized using a metal ion-mediated hydrothermal route. Thereafter, some of the samples were annealed at 500 °C for 3 h. Our paper combines the experimental part with theoretical calculations of the obtained materials' band edge positions. The results reveal that-aside from hematite-the as-synthesized discs also contain γ-FeOOH and ß-Fe2O3 phases, which transform into α-Fe2O3 during annealing. The hydrodynamic diameter, zeta potential, and adsorption kinetics measurements show that the cube-like samples exhibit the highest affinity for cationic, whereas the discs have an affinity for anionic dye. Measurements of the wall zeta potential also reveal that annealing the discs modifies their surface state and ability to adsorb molecules. Photocatalytic tests show that the as-synthesized powders have better photocatalytic performance toward methylene blue decomposition than the annealed ones. The observed small changes in the concentration of the MO during illumination result from the energy band structure of the cube-like crystal orientation.

Exploring Selenide Synthesis Pathways for Optimizing Energy Conversion.

This study investigated the structural and electrochemical characteristics of binary and quaternary systems comprising nickel, cobalt, and iron selenides. The powders were obtained via a solvothermal route. X-ray diffraction (XRD) and Raman spectroscopy revealed significant phase diversity. It was observed that increasing the proportion of d-block metals in quaternary systems enhances structural entropy, potentially leading to more homogeneous and stable structures dominated by energetically preferred components such as nickel. The electrochemical analysis indicated that the binary system exhibited a reversible redox reaction, with nickel selenide-based samples demonstrating the highest electrochemically active surface area. Quaternary systems display varying degrees of electrochemical stability. An equal contribution of nickel, cobalt, and iron appears beneficial in achieving stable electrodes. This research contributes to understanding the relationship between transition metal selenides' structural, morphological, and electrochemical properties, providing insights into their potential applications in hydrogen generation.

Voltammetric Detection of Glucose-The Electrochemical Behavior of the Copper Oxide Materials with Well-Defined Facets.

Cu2O nanomaterials with well-defined facets and uniform size were synthesized by a wet-chemical method. Regardless of the additive composition, powders crystallize mostly in cuprite form. To compare their electrochemical behavior, the obtained materials were deposited on carbon glassy electrodes. The response to glucose from the materials with different exposed facets was recorded with a delay at the anodic curve. The chronoamperometric analyses (AMP) exhibited a lower signal in contrast to the cyclic voltammetry data (CV), indicating that the number of active sites involved in glucose oxidation processes resulting from the structure of the material is insufficient. For samples with dominant (100) or (111) planes, a typical characteristic was observed, however, with an additional peak at the anodic curve. The location of the peaks is approximately the same and no significant differences from the AMP and CV analysis were observed. The sample enclosed by the (111) facets exhibited higher activity; however, as a result of the redox reaction with glucose molecules, the surface state is changing. Cu2O materials enclosed by (100) planes exhibited optimal sensitivity as well as a large detective range. Samples with differential facet exposition present various current-potential profiles, as the effect of binder-particle interaction with Nafion.

Electrochemical Characterization of Modified Glassy Carbon Electrodes for Non-Enzymatic Glucose Sensors.

The diversity of materials proposed for non-enzymatic glucose detection and the lack of standardized protocols for assessing sensor performance have caused considerable confusion in the field. Therefore, methods for pre-evaluation of working electrodes, which will enable their conscious design, are currently intensively sought. Our approach involved comprehensive morphologic and structural characterization of copper sulfides as well as drop-casted suspensions based on three different polymers-cationic chitosan, anionic Nafion, and nonionic polyvinylpyrrolidone (PVP). For this purpose, scanning electron microscopy (SEM), X-ray diffraction (XRD), and Raman spectroscopy were applied. Subsequently, comparative studies of electrochemical properties of bare glassy carbon electrode (GCE), polymer- and copper sulfides/polymer-modified GCEs were performed using electrochemical impedance spectroscopy (EIS) and voltammetry. The results from EIS provided an explanation for the enhanced analytical performance of Cu-PVP/GCE over chitosan- and Nafion-based electrodes. Moreover, it was found that the pH of the electrolyte significantly affects the electrocatalytic behavior of copper sulfides, indicating the importance of OHads in the detection mechanism. Additionally, diffusion was denoted as a limiting step in the irreversible electrooxidation process that occurs in the proposed system.

Nonenzymatic Glucose Sensors Based on Copper Sulfides: Effect of Binder-Particles Interactions in Drop-Casted Suspensions on Electrodes Electrochemical Performance.

The constant progress in novel nanomaterials synthesis has contributed to the rapid development of nonenzymatic glucose sensors. For working electrodes preparation, drop casting proved to be the most convenient and thus most widely applied method. However, appropriate interpretation of obtained electrochemical signal requires in-depth knowledge of limitations related to this technique. In this study, we prepared solutions based on commonly reported polymers for nanostructures immobilization and investigated their influence on copper sulfides distribution on the electrode. Characterization of suspensions properties and behavior of particles during droplet drying revealed that nonionic polyvinylpyrrolidone (PVP) was favorable for electrodes modification with copper sulfides in comparison with Nafion and chitosan. It ensured homogeneity of the suspension as well as the uniform coverage of the electrode surface with particles, what resulted in increased active surface area and, therefore, higher signal from glucose addition. On the other hand, when cationic chitosan was used as a binder, suspensions were agglomerated and, within dry deposits, a coffee-ring effect was observed. Appropriate adjustment of material and polymer interactions led to enhanced electrode electrochemical performance.

From Adsorbent to Photocatalyst: The Sensitization Effect of SnO2 Surface towards Dye Photodecomposition.

Semiconductor photocatalysis is considered one of the most promising technologies for water purification from toxic organic dyes. However, to reliably evaluate the possibility of using a given material as a photocatalyst, it is crucial to investigate not only the photocatalytic activity but also its affinity towards various dyes and reusability. In this work, we studied the adsorptive/photocatalytic properties of hollow-spherical raspberry-like SnO2 and its SnO2/SnS2 heterostructures that were obtained via a chemical conversion method using three different concentrations of a sulfide precursor (thioacetamide). The adsorptive/photocatalytic properties of the samples towards cationic rhodamine B (RhB) and anionic indigo carmine (IC) were analyzed using uncommon wall zeta potential measurements, hydrodynamic diameter studies, and adsorption/photodecomposition tests. Moreover, after conducting cyclic experiments, we investigated the (micro)structural changes of the reused photocatalysts by scanning electron microscopy and Fourier-transform infrared spectroscopy. The obtained results revealed that the sensitization of SnO2 resulted not only in the significantly enhanced photocatalytic performance of the heterostructures, but also completely changed their affinity towards dyes. Furthermore, despite the seemingly best photocatalytic performance, the sample with the highest SnS2 content was unstable due to its (micro)structure. This work demonstrates that dye adsorption/desorption processes may overlap the results of cyclic photodecomposition kinetics.

Transition-Metal-Based Compounds for Electrochemical Energy Conversion Processes.

The era of ever-growing worldwide energy requirements demands the development of new methods of energy conversion, where the design of novel materials and the improvement of the efficiency of existing ones are of great importance [...].

Thermoelectric Properties of Cu2Se Synthesized by Hydrothermal Method and Densified by SPS Technique.

The aim of the work was to obtain copper (I) selenide Cu2Se material with excellent thermoelectric properties, synthesized using the hydrothermal method and densified by the spark plasma sintering (SPS) method. Chemical and phase composition studies were carried out by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) methods. Measurements of thermoelectric transport properties, i.e., electrical conductivity, the Seebeck coefficient, and thermal conductivity in the temperature range from 300 to 965 K were carried out. Based on these results, the temperature dependence of the thermoelectric figure of merit ZT as a function of temperature was determined. The obtained, very high ZT parameter (ZT~1.75, T = 965 K) is one of the highest obtained so far for undoped Cu2Se.

Search for mid- and high-entropy transition-metal chalcogenides - investigating the pentlandite structure.

For the first time, transition metal-based chalcogenides conforming to the definition of high entropy materials, are synthesized, with the multicomponent occupation being utilized on both cationic and anionic sublattices. The pentlandite-structured (Co,Fe,Ni)9S8 and (Co,Fe,Ni)9(S,Se)8 compositions are obtained using a two-stage, solid-state reaction method. Room temperature structural analysis (XRD, SEM, Raman) in both cases indicates the presence of a homogeneous, single-phase, Fm3[combining macron]m structure, with a profound effect of Se addition on the lattice parameters. The obtained materials possess an excellent electrical conductivity of 105 S m-1, and slightly negative Seebeck coefficient values, resulting from their metallic character, combined with a low thermal conductivity of 2.5 W m-1 K-1, especially when compared with conventional analogues. The optical measurements reveal very promising behavior in the UV/vis range. The electrochemical sensitivity towards hydrazine and acetaminophen is also presented, making them potentially interesting for sensor devices. Based on the DFT analysis of various sub-systems, the origins of the observed transport and optical behavior are explained. Furthermore, it is shown that the application of the high-entropy principle to both sublattices simultaneously allows for extensive tailoring of the band structure, allowing these materials to be optimized with respect to the given application, including thermoelectric and photoelectrochemical devices and catalysis, e.g., the hydrogen evolution reaction.

Nanocrystalline TiO2/SnO2 heterostructures for gas sensing.

The aim of this research is to study the role of nanocrystalline TiO2/SnO2 n-n heterojunctions for hydrogen sensing. Nanopowders of pure SnO2, 90 mol % SnO2/10 mol % TiO2, 10 mol % SnO2/90 mol % TiO2 and pure TiO2 have been obtained using flame spray synthesis (FSS). The samples have been characterized by BET, XRD, SEM, HR-TEM, Mössbauer effect and impedance spectroscopy. Gas-sensing experiments have been performed for H2 concentrations of 1-3000 ppm at 200-400 °C. The nanomaterials are well-crystallized, anatase TiO2, rutile TiO2 and cassiterite SnO2 polymorphic forms are present depending on the chemical composition of the powders. The crystallite sizes from XRD peak analysis are within the range of 3-27 nm. Tin exhibits only the oxidation state 4+. The H2 detection threshold for the studied TiO2/SnO2 heterostructures is lower than 1 ppm especially in the case of SnO2-rich samples. The recovery time of SnO2-based heterostructures, despite their large responses over the whole measuring range, is much longer than that of TiO2-rich samples at higher H2 flows. TiO2/SnO2 heterostructures can be intentionally modified for the improved H2 detection within both the small (1-50 ppm) and the large (50-3000 ppm) concentration range. The temperature Tmax at which the semiconducting behavior begins to prevail upon water desorption/oxygen adsorption depends on the TiO2/SnO2 composition. The electrical resistance of sensing materials exhibits a power-law dependence on the H2 partial pressure. This allows us to draw a conclusion about the first step in the gas sensing mechanism related to the adsorption of oxygen ions at the surface of nanomaterials.

Nanostructured TiO2-based gas sensors with enhanced sensitivity to reducing gases.

2D TiO2 thin films and 3D flower-like TiO2-based nanostructures, also decorated with SnO2, were prepared by chemical and thermal oxidation of Ti substrates, respectively. The crystal structure, morphology and gas sensing properties of the TiO2-based sensing materials were investigated. 2D TiO2 thin films crystallized mainly in the form of rutile, while the flower-like 3D nanostructures as anatase. The sensor based on the 2D TiO2 showed the best performance for H2 detection, while the flower-like 3D nanostructures exhibited enhanced selectivity to CO(CH3)2 after sensitization by SnO2 nanoparticles. The sensor response time was of the order of several seconds. Their fast response, high sensitivity to selected gas species, improved selectivity and stability suggest that the SnO2-decorated flower-like 3D nanostructures are a promising material for application as an acetone sensor.

Biopolymeric hydrogels - nanostructured TiO2 hybrid materials as potential injectable scaffolds for bone regeneration.

The present work aims at development of novel hybrid materials from genipin crosslinked collagen or collagen/chitosan hydrogels containing various types of TiO2 nanoparticles characterized with different anatase/rutile ratios. Collagen and chitosan were selected as hydrogel components since they are biopolymers being, like collagen, the major compound present in extracellular matrix or exhibit structural similarity to glycosaminoglycans, like chitosan. TiO2 nanoparticles were introduced to the hydrogel matrices to improve their mechanical properties as well as bioactivity. A series of twelve novel hybrid materials were prepared and their physicochemical, mechanical and biological properties were evaluated. It was found that TiO2 nanostructures introduced to the hydrogels have significant influence on the swelling properties of the synthesized hybrids and their impact is strongly dependent on the type of matrices. The surfaces of hybrid materials were found to be more hydrophilic than these of corresponding hydrogel matrix. It was also observed that, the storage modulus values of the hybrids based on collagen-chitosan hydrogel are comparable to these for plain hydrogels what indicates that the mechanical properties of the materials obtained are satisfactory for possible biomedical application. The in vitro cell culture studies have shown that prepared materials are biocompatible as they can support mitochondrial activity of MEFs as well as MG-63 cells. In vitro experiments performed under simulated body fluid (SBF) conditions have revealed that all studied TiO2 nanoparticles present in hydrogel matrices, regardless of anatase/rutile ratio, successfully induced formation of apatite-like structures. The hybrid materials developed here are promising candidates for preparation of bioactive, injectable scaffolds for tissue engineering.