High-Performance and Stable Colloidal Quantum Dots Imager via Energy Band Engineering.

Solution-processed colloidal quantum dot (CQD) photodiodes are compatible for monolithic integration with silicon-based readout circuitry, enabling ultrahigh resolution and ultralow cost infrared imagers. However, top-illuminated CQD photodiodes for longer infrared imaging suffer from mismatched energy band alignment between narrow-bandgap CQDs and the electron transport layer. In this work, we designed a new top-illuminated structure by replacing the sputtered ZnO layer with a SnO2 layer by atomic layer deposition. Benefiting from matched energy band alignment and improved heterogeneous interface, our top-illuminated CQD photodiodes achieve a broad-band response up to 1650 nm. At 220 K, these SnO2-based devices exhibit an ultralow dark current density of 3.5 nA cm-2 at -10 mV, reaching the noise limit for passive night vision. The detectivity is 4.1 × 1012 Jones at 1530 nm. These SnO2-based devices also demonstrate exceptional operation stability. By integrating with silicon-based readout circuitry, our CQD imager realizes water/oil discrimination and see-through smoke imaging.

Ligand-Engineered HgTe Colloidal Quantum Dot Solids for Infrared Photodetectors.

HgTe colloidal quantum dots (CQDs) are promising absorber systems for infrared detection due to their widely tunable photoresponse in all infrared regions. Up to now, the best-performing HgTe CQD photodetectors have relied on using aggregated CQDs, limiting the device design, uniformity and performance. Herein, we report a ligand-engineered approach that produces well-separated HgTe CQDs. The present strategy first employs strong-binding alkyl thioalcohol ligands to enable the synthesis of well-dispersed HgTe cores, followed by a second growth process and a final postligand modification step enhancing their colloidal stability. We demonstrate highly monodisperse HgTe CQDs in a wide size range, from 4.2 to 15.0 nm with sharp excitonic absorption fully covering short- and midwave infrared regions, together with a record electron mobility of up to 18.4 cm2 V-1 s-1. The photodetectors show a room-temperature detectivity of 3.9 × 1011 jones at a 1.7 µm cutoff absorption edge.

Phase-Transfer Exchange Lead Chalcogenide Colloidal Quantum Dots: Ink Preparation, Film Assembly, and Solar Cell Construction.

Solution-processed colloidal quantum dots (CQDs) are promising candidates for the third-generation photovoltaics due to their low cost and spectral tunability. The development of CQD solar cells mainly relies on high-quality CQD ink, smooth and dense film, and charge-extraction-favored device architectures. In particular, advances in the processing of CQDs are essential for high-quality QD solids. The phase transfer exchange (PTE), in contrast with traditional solid-state ligand exchange, has demonstrated to be the most promising approach for high-quality QD solids in terms of charge transport and defect passivation. As a result, the efficiencies of Pb chalcogenide CQD solar cells have been rapidly improved to 14.0%. In this review, the development of the PTE method is briefly reviewed for lead chalcogenide CQD ink preparation, film assembly, and device construction. Particularly, the key roles of lead halides and additional additives are emphasized for defect passivation and charge transport improvement. In the end, several potential directions for future research are proposed.

Matching Charge Extraction Contact for Infrared PbS Colloidal Quantum Dot Solar Cells.

Infrared solar cells (IRSCs) can supplement silicon or perovskite SCs to broaden the utilization of the solar spectrum. As an ideal infrared photovoltaic material, PbS colloidal quantum dots (CQDs) with tunable bandgaps can make good use of solar energy, especially the infrared region. However, as the QD size increases, the energy level shrinking and surface facet evolution makes us reconsider the matching charge extraction contacts and the QD passivation strategy. Herein, different to the traditional sol-gel ZnO layer, energy-level aligned ZnO thin film from a magnetron sputtering method is adopted for electron extraction. In addition, a modified hybrid ligand recipe is developed for the facet passivation of large size QDs. As a result, the champion IRSC delivers an open circuit voltage of 0.49 V and a power conversion efficiency (PCE) of 10.47% under AM1.5 full-spectrum illumination, and the certified PCE is over 10%. Especially the 1100 nm filtered efficiency achieves 1.23%. The obtained devices also show high storage stability. The present matched electron extraction and QD passivation strategies are expected to highly booster the IR conversion yield and promote the fast development of new conception QD optoelectronics.

Cation-Exchange Enables In Situ Preparation of PbSe Quantum Dot Ink for High Performance Solar Cells.

Lead selenide (PbSe) colloidal quantum dots (CQDs) are promising candidates for optoelectronic applications. To date, PbSe CQDs capped by halide ligands exhibit improved stability and solar cells using these CQDs as active layers have reported a remarkable power conversion efficiency (PCE) up to 10%. However, PbSe CQDs are more prone to oxidation, requiring delicate control over their processability and compromising their applications. Herein, an efficient strategy that addresses this issue by an in situ cation-exchange process is reported. This is achieved by a two-phase ligand exchange process where PbI2 serves as both a passivating ligand and cation-source inducing transformation of CdSe to PbSe. The defect density and carrier lifetime of PbSe CQD films are improved to 1.05 × 1016  cm-3 and 12.2 ns, whereas the traditional PbSe CQD films possess 1.9 × 1016  cm-3 defect density and 10.2 ns carrier lifetime. These improvements are translated into an enhancement of photovoltaic performance of PbSe solar cells, with a PCE of up to 11.6%, ≈10% higher than the previous record. Notably, the approach enables greatly improved stability and a two-month stability is successfully demonstrated. This strategy is expected to promote the fast development of PbSe CQD applications in low-cost and high-performance optoelectronic devices.

Quantum dot solids showing state-resolved band-like transport.

Improving charge mobility in quantum dot (QD) films is important for the performance of photodetectors, solar cells and light-emitting diodes. However, these applications also require preservation of well defined QD electronic states and optical transitions. Here, we present HgTe QD films that show high mobility for charges transported through discrete QD states. A hybrid surface passivation process efficiently eliminates surface states, provides tunable air-stable n and p doping and enables hysteresis-free filling of QD states evidenced by strong conductance modulation. QD films dried at room temperature without any post-treatments exhibit mobility up to µ ~ 8 cm2 V-1 s-1 at a low carrier density of less than one electron per QD, band-like behaviour down to 77 K, and similar drift and Hall mobilities at all temperatures. This unprecedented set of electronic properties raises important questions about the delocalization and hopping mechanisms for transport in QD solids, and introduces opportunities for improving QD technologies.

Hybrid organic-inorganic inks flatten the energy landscape in colloidal quantum dot solids.

Bandtail states in disordered semiconductor materials result in losses in open-circuit voltage (Voc) and inhibit carrier transport in photovoltaics. For colloidal quantum dot (CQD) films that promise low-cost, large-area, air-stable photovoltaics, bandtails are determined by CQD synthetic polydispersity and inhomogeneous aggregation during the ligand-exchange process. Here we introduce a new method for the synthesis of solution-phase ligand-exchanged CQD inks that enable a flat energy landscape and an advantageously high packing density. In the solid state, these materials exhibit a sharper bandtail and reduced energy funnelling compared with the previous best CQD thin films for photovoltaics. Consequently, we demonstrate solar cells with higher Voc and more efficient charge injection into the electron acceptor, allowing the use of a closer-to-optimum bandgap to absorb more light. These enable the fabrication of CQD solar cells made via a solution-phase ligand exchange, with a certified power conversion efficiency of 11.28%. The devices are stable when stored in air, unencapsulated, for over 1,000 h.

Hybrid Colloidal Stabilization Mechanism toward Improved Photoluminescence and Stability of CdSe/CdS Core/Shell Quantum Dots.

Colloidal quantum dots can be stabilized in either a polar solvent or a nonpolar solvent depending on their surface chemistry. The former is typically achieved by charge stabilization while the latter by steric hindrance. This allows reversible tuning of their surface polarity for targeted application by engineering their ligand profile. Here we developed a hybrid stabilization approach that leveraged a combination of steric hindrance and charge stabilization simultaneously. We demonstrated this mechanism in a phase transfer process where hexane dispersed and hydrophobic CdSe/CdS core/shell quantum dots were exchanged into the hydrophilic dimethylformamide (DMF) phase. This was achieved by employing both Z-type cadmium acetate and X-type halide ligands. The results suggested only by using this hybrid stabilization strategy were we able to achieve good colloidal stability while preserving their photoluminescence quantum yield. This hybrid ligand strategy may promise new opportunities for the application of QDs in optoelectronic areas.

10.6% Certified Colloidal Quantum Dot Solar Cells via Solvent-Polarity-Engineered Halide Passivation.

Colloidal quantum dot (CQD) solar cells are solution-processed photovoltaics with broad spectral absorption tunability. Major advances in their efficiency have been made via improved CQD surface passivation and device architectures with enhanced charge carrier collection. Herein, we demonstrate a new strategy to improve further the passivation of CQDs starting from the solution phase. A cosolvent system is employed to tune the solvent polarity in order to achieve the solvation of methylammonium iodide (MAI) and the dispersion of hydrophobic PbS CQDs simultaneously in a homogeneous phase, otherwise not achieved in a single solvent. This process enables MAI to access the CQDs to confer improved passivation. This, in turn, allows for efficient charge extraction from a thicker photoactive layer device, leading to a certified solar cell power conversion efficiency of 10.6%, a new certified record in CQD photovoltaics.

Colloidal Quantum Dot Photovoltaics Enhanced by Perovskite Shelling.

Solution-processed quantum dots are a promising material for large-scale, low-cost solar cell applications. New device architectures and improved passivation have been instrumental in increasing the performance of quantum dot photovoltaic devices. Here we report photovoltaic devices based on inks of quantum dot on which we grow thin perovskite shells in solid-state films. Passivation using the perovskite was achieved using a facile solution ligand exchange followed by postannealing. The resulting hybrid nanostructure created a more intrinsic CQD film, which, when incorporated into a photovoltaic device with graded bandstructure, achieved a record solar cell performance for single-step-deposited CQD films, exhibiting an AM1.5 solar power conversion efficiency of 8.95%.

High-Efficiency Colloidal Quantum Dot Photovoltaics via Robust Self-Assembled Monolayers.

The optoelectronic tunability offered by colloidal quantum dots (CQDs) is attractive for photovoltaic applications but demands proper band alignment at electrodes for efficient charge extraction at minimal cost to voltage. With this goal in mind, self-assembled monolayers (SAMs) can be used to modify interface energy levels locally. However, to be effective SAMs must be made robust to treatment using the various solvents and ligands required for to fabricate high quality CQD solids. We report robust self-assembled monolayers (R-SAMs) that enable us to increase the efficiency of CQD photovoltaics. Only by developing a process for secure anchoring of aromatic SAMs, aided by deposition of the SAMs in a water-free deposition environment, were we able to provide an interface modification that was robust against the ensuing chemical treatments needed in the fabrication of CQD solids. The energy alignment at the rectifying interface was tailored by tuning the R-SAM for optimal alignment relative to the CQD quantum-confined electron energy levels. This resulted in a CQD PV record power conversion efficiency (PCE) of 10.7% with enhanced reproducibility relative to controls.

Self-Assembled PbSe Nanowire:Perovskite Hybrids.

Inorganic semiconductor nanowires are of interest in nano- and microscale photonic and electronic applications. Here we report the formation of PbSe nanowires based on directional quantum dot alignment and fusion regulated by hybrid organic-inorganic perovskite surface ligands. All material synthesis is carried out at mild temperatures. Passivation of PbSe quantum dots was achieved via a new perovskite ligand exchange. Subsequent in situ ammonium/amine substitution by butylamine enables quantum dots to be capped by butylammonium lead iodide, and this further drives the formation of a PbSe nanowire superlattice in a two-dimensional (2D) perovskite matrix. The average spacing between two adjacent nanowires agrees well with the thickness of single atomic layer of 2D perovskite, consistent with the formation of a new self-assembled semiconductor nanowire:perovskite heterocrystal hybrid.

Charge-extraction strategies for colloidal quantum dot photovoltaics.

The solar-power conversion efficiencies of colloidal quantum dot solar cells have advanced from sub-1% reported in 2005 to a record value of 8.5% in 2013. Much focus has deservedly been placed on densifying, passivating and crosslinking the colloidal quantum dot solid. Here we review progress in improving charge extraction, achieved by engineering the composition and structure of the electrode materials that contact the colloidal quantum dot film. New classes of structured electrodes have been developed and integrated to form bulk heterojunction devices that enhance photocharge extraction. Control over band offsets, doping and interfacial trap state densities have been essential for achieving improved electrical communication with colloidal quantum dot solids. Quantum junction devices that not only tune the optical absorption spectrum, but also provide inherently matched bands across the interface between p- and n-materials, have proven that charge separation can occur efficiently across an all-quantum-tuned rectifying junction.

In-Synthesis Se-Stabilization Enables Defect and Doping Engineering of HgTe Colloidal Quantum Dots.

Colloidal Quantum Dots (CQDs) of mercury telluride (HgTe) hold particular appeal for infrared photodetection due to their widely tunable infrared absorption and good compatibility with silicon electronics. While advances in surface chemistry have led to improved CQD solids, the chemical stability of HgTe material is not fully emphasized. In this study, it is aimed to address this issue and identifies a Se-stabilization strategy based on the surface coating of Se on HgTe CQDs via engineering in the precursor reactivity. The presence of Se-coating enables HgTe CQDs with improved colloidal stability, passivation, and enhanced degree of freedom in doping tuning. This enables the construction of optimized p-i-n HgTe CQD infrared photodetectors with an ultra-low dark current 3.26 × 10-6 A cm⁻2 at -0.4 V and room-temperature specific detectivity of 5.17 × 1011 Jones at wavelength ≈2 um, approximately one order of magnitude improvement compared to that of the control device. The stabilizing effect of Se is well preserved in the thin film state, contributing to much improved device stability. The in-synthesis Se-stabilization strategy highlights the importance of the chemical stability of materials for the construction of semiconductor-grade CQD solids and may have important implications for other high-performance CQD optoelectronic devices.

Short-Wave Infrared Detection and Imaging Employing Size-Customized HgTe Nanocrystals.

HgTe nanocrystals (NCs) possess advantages including tunable infrared absorption spectra, solution processability, and low fabrication costs, offering new avenues for the advancement of next-generation infrared detectors. In spite of great synthetic advances, it remains essential to achieve customized synthesis of HgTe NCs in terms of industrial applications. Herein, by taking advantage of a high critical nucleation concentration of HgTe NCs, a continuous-dropwise (CD) synthetic approach that features the addition of the anion precursors in a feasible drop-by-drop fashion is demonstrated. The slow reaction dynamics enable size-customized synthesis of HgTe NCs with sharp band tails and wide absorption range fully covering the short- and mid-infrared regions. More importantly, the intrinsic advantages of CD process ensure high-uniformity and scale-up synthesis from batch to batch without compromising the excitonic features. The resultant HgTe nanocrystal photodetectors show a high room-temperature detectivity of 8.1 × 1011 Jones at 1.7 µm cutoff absorption edge. This CD approach verifies a robust method for controlled synthesis of HgTe NCs and might have important implications for scale-up synthesis of other nanocrystal materials.

Planar Cation Passivation on Colloidal Quantum Dots Enables High-Performance 0.35-1.8 µm Broadband TFT Imager.

Solution-processed colloidal quantum dots (CQDs) are promising candidates for broadband photodetectors from visible light to shortwave infrared (SWIR). However, large-size PbS CQDs sensitive to longer SWIR are mainly exposed with nonpolar (100) facets on the surface, which lack robust passivation strategies. Herein, an innovative passivation strategy that employs planar cation, is introduced to enable face-to-face coupling on (100) facets and strengthen halide passivation on (111) facets. The defect density of CQDs film (Eg ≈ 0.74 eV) is reduced from 2.74 × 1015 to 1.04  × 1015 cm-3, coupled with 0.1 eV reduction in the activation energy of defects. The resultant CQDs photodiodes exhibit a low dark current density of 14 nA cm-2 with a high external quantum efficiency (EQE) of 62%, achieving a linear dynamic range of 98 dB, a -3dB bandwidth of 103 kHz and a detectivity of 4.7 × 1011 Jones. The comprehensive performance of the CQDs photodiodes outperforms previously reported CQDs photodiodes operating at >1.6 µm. By monolithically integrated with thin-film transistor (TFT) readout circuit, the broadband CQDs imager covering 0.35-1.8 µm realizes the functions including silicon wafer perspectivity and material discrimination, showing its potential for wide range of applications.

High quantum-yield CdSexS1-x/ZnS core/shell quantum dots for warm white light-emitting diodes with good color rendering.

Composition-controllable ternary CdSe(x)S(1-x) quantum dots (QDs) with multiple emission colors were obtained via a hot-injection-like method at a relatively low injection temperature (230 ° C) in octadecene. Then highly fluorescent CdSe(x)S(1-x)/ZnS core/shell (CS) QDs were synthesized by a facile single-molecular precursor approach. The fluorescent quantum yield of the resulting green (λ(em) = 523 nm), yellow (λ(em) = 565 nm) and red (λ(em) = 621 nm) emission of CS QDs in toluene reached up to 85%, 55% and 39%, respectively. Moreover, a QDs white light-emitting diode (QDs-WLED) was fabricated by hybridizing green-, yellow- and red-emitting CdSe(x)S(1-x)/ZnS CS QDs/epoxy composites on a blue InGaN chip. The resulting four-band RYGB QDs-WLED showed good performance with CIE-1931 coordinates of (0.4137, 0.3955), an R(a) of 81, and a T(c) of 3360 K at 30 mA, which indicated the combination of multiple-color QDs with high fluorescence QYs in LEDs as a promising approach to obtain warm WLEDs with good color rendering.

Large stokes shift of Ag doped CdSe quantum dots via aqueous route.

Monodispersed and luminescent Ag-doped CdSe semiconductor quantum dots (d-dots) were synthesized by an aqueous route assisted with electrochemical preparation of Se source with 3-mercaptopropionic acid as stabilizer. The silver dopants were incorporated into the host crystals via cation-exchange mechanism. X-ray diffraction patterns revealed that the as-synthesized CdSe:Ag d-dots were well retained in the zinc blende structure. The CdSe:Ag d-dots that exhibited uniform size distribution and good crystallnity could be observed by High-resolution transmission electron microscopy (HRTEM), with average diameter of 2.7 nm. Successful doping was confirmed by X-ray photoelectron spectroscopy survey spectra. The peculiar Ag-related photoluminescence showed strong intensity, and at the same time, intrinsic band-edge exciton emission of CdSe QDs was suppressed. The dopant emission exhibited larger Stockes shift of - 0.51 eV than that of the band-gap emission, and varied from 546 to 583 nm by changing electrolytic time. Possible radiative recombination mechanism of the aqueous Ag-doped CdSe d-dots was discussed. The results demonstrated that doping can be an effective way to manipulate the optical properties of semiconductor nanocrystals.

High-Performance Colloidal Quantum Dot Photodiodes via Suppressing Interface Defects.

PbS colloidal quantum dot (CQD) infrared photodiodes have attracted wide attention due to the prospect of developing cost-effective infrared imaging technology. Presently, ZnO films are widely used as the electron transport layer (ETL) of PbS CQDs infrared photodiodes. However, ZnO-based devices still suffer from the problems of large dark current and low repeatability, which are caused by the low crystallinity and sensitive surface of ZnO films. Here, we effectively optimized the device performance of PbS CQDs infrared photodiode via diminishing the influence of adsorbed H2O at the ZnO/PbS CQDs interface. The polar (002) ZnO crystal plane showed much higher adsorption energy of H2O molecules compared with other nonpolar planes, which could reduce the interface defects induced by detrimentally adsorbed H2O. Based on the sputtering method, we obtained the [002]-oriented and high-crystallinity ZnO ETL and effectively suppressed the adsorption of detrimental H2O molecules. The prepared PbS CQDs infrared photodiode with the sputtered ZnO ETL demonstrated lower dark current density, higher external quantum efficiency, and faster photoresponse compared with the sol-gel ZnO device. Simulation results further unveiled the relationship between interface defects and device dark current. Finally, a high-performance sputtered ZnO/PbS CQDs device was obtained with a specific detectivity of 2.15 × 1012 Jones at -3 dB bandwidth (94.6 kHz).

Flexible and broadband colloidal quantum dots photodiode array for pixel-level X-ray to near-infrared image fusion.

Combining information from multispectral images into a fused image is informative and beneficial for human or machine perception. Currently, multiple photodetectors with different response bands are used, which require complicated algorithms and systems to solve the pixel and position mismatch problem. An ideal solution would be pixel-level multispectral image fusion, which involves multispectral image using the same photodetector and circumventing the mismatch problem. Here we presented the potential of pixel-level multispectral image fusion utilizing colloidal quantum dots photodiode array, with a broadband response range from X-ray to near infrared and excellent tolerance for bending and X-ray irradiation. The colloidal quantum dots photodiode array showed a specific detectivity exceeding 1012 Jones in visible and near infrared range and a favorable volume sensitivity of approximately 2 × 105 µC Gy-1 cm-3 for X-ray irradiation. To showcase the advantages of pixel-level multispectral image fusion, we imaged a capsule enfolding an iron wire and soft plastic, successfully revealing internal information through an X-ray to near infrared fused image.