Three-Dimensional Printing of Molecularly Imprinted Polymers by Digital Light Processing for Copper Ion Sequestration.

Highly structured, molecularly imprinted polymer (MIP) networks for copper(II) ion sequestration have been realized using the additive manufacturing technology. Photopolymerizable formulations with acrylic functional monomers and two different porogens (water and methanol) in different ratios were studied to produce emulsions with 50 vol% of the internal phase. The results of morphological characterization indicate that all MIPs have cauliflower-like multiscale structures that change as a function of the solvent combination and fabrication process. X-ray fluorescence microscopy maps presented a layered structure and homogeneous distribution of copper in the printed MIP. Copper(II) ion adsorption-desorption tests were performed on MIPs prepared using a three-dimensional (3D) printing approach and MIPs prepared by bulk polymerization. Results indicate that the 3D printed MIP is able to absorb copper up to ten times more efficiently than the nonprinted one and the printed MIP with 100% water content has the highest imprint recognition.

Datasets on the production routes and the properties of plant powders for manufacturing of green products.

The diversity of the plant biomass available on earth makes plants an exceptional resource for replacing fossil resources in green chemistry, bioenergy and biobased materials. For numerous applications, and especially the high-tech ones (building block molecules, high-power bioenergy, additive manufacturing of biobased materials), the macrostructure assemblies of the plant biomass often need to be first broken down into a fine powder. This can be achieved by dry fractionation process combining comminution and sorting steps. The chemical and physical properties of the ground plant powder results both from the process conditions, the histological structure and chemical composition of the raw plant materials. In a forward engineering approach, the quality of the final products can be highly improved by the selection of the right powder (raw materials and production process) for the right application. This article provides production routes together with physical and chemical characterization of 10 biomass powders from 6 different biomass feedstocks (SP - spirulina, HI - hibiscus, PB - pine bark, HC - hemp Core, RH - rice husk and RHA - rice husk ash). These feedstocks represent a broad range of raw materials properties. For pine bark, hemp core, rice husk and rice husk ash, two grades of powders related to two different particle sizes were produced by two different routes to highlight the impact of the comminution process on the powder properties. The devices used and the process parameters are described. The morphological properties of the powder were quantified using laser diffraction (particle size) and image analysis (shape factor) and qualitatively analyzed with SEM. The specific surface area was determined using gas sorption with BET theory, and the hygroscopic properties were measured using direct vapor sorption. The chemical characterizations were determined with a set of biochemical assays and, complementary, FTIR and fluorescence spectra were recorded to provide fingerprints of samples. The dataset includes tables that summarize the main characteristic descriptors of each analysis as well as the raw data. The data are registered in the French Research Data Gouv public repository and also stored in the PO2 BaGaTel database using the PO2/TransformON ontology [1]. SPO2Q web tool allows on line querying of the database, which can also be consulted using PO2 manager desktop application [[1], [2], [3]].

Ectopic callose deposition into woody biomass modulates the nano-architecture of macrofibrils.

Plant biomass plays an increasingly important role in the circular bioeconomy, replacing non-renewable fossil resources. Genetic engineering of this lignocellulosic biomass could benefit biorefinery transformation chains by lowering economic and technological barriers to industrial processing. However, previous efforts have mostly targeted the major constituents of woody biomass: cellulose, hemicellulose and lignin. Here we report the engineering of wood structure through the introduction of callose, a polysaccharide novel to most secondary cell walls. Our multiscale analysis of genetically engineered poplar trees shows that callose deposition modulates cell wall porosity, water and lignin contents and increases the lignin-cellulose distance, ultimately resulting in substantially decreased biomass recalcitrance. We provide a model of the wood cell wall nano-architecture engineered to accommodate the hydrated callose inclusions. Ectopic polymer introduction into biomass manifests in new physico-chemical properties and offers new avenues when considering lignocellulose engineering.

Quantifying the Shape Memory Performance of a Three-Dimensional-Printed Biobased Polyester/Cellulose Composite Material.

A biobased composite material with heat-triggered shape memory ability was successfully formulated for three-dimensional (3D) printing. It was produced from cellulose nanocrystals and cellulose micro-powder particles within a bioderived thermally cured polyester matrix based on glycerol, citric acid, and sebacic acid. The effect of curing duration on the material's shape memory behavior was quantified by using two thermo-mechanical approaches to measure recovery: (1) displacement in three-point bending and (2) angular recovery from a beam bent at 90° in a single cantilever setup. Extending curing duration increased the material's glass-transition temperature from -26°C after 6 h to 13°C after 72 h of curing. Fourier-transform infrared spectroscopy confirmed the associated progressive conversion of functional groups consistent with polyester formation. Slow recovery rates and low levels of shape recovery (22-70%) were found for samples cured less than 24 h. Those results also indicated a high dependence on the measurement approach. In contrast, samples cured for 48 and 72 h exhibited faster recovery rates, a significantly higher recovery percentage (90-100%) and were less sensitive to the measurement approach. Results demonstrated that once a sufficient curing threshold was achieved, additional curing time could be used to tune the material glass-transition temperature and create heat-triggered 3D-printed products.

Influence of Rice Husk and Wood Biomass Properties on the Manufacture of Filaments for Fused Deposition Modeling.

Additive manufacturing or 3D printing has the potential to displace some of the current manufacturing techniques and is particularly attractive if local renewable waste resources can be used. In this study, rice husk, and wood powders were compounded in polylactic acid (PLA) by twin screw extrusion to produce filaments for fused-deposition modeling 3D printing. The biomasses were characterized in terms of physical features (e.g., particle size, density) and chemical compositions (e.g., solid state nuclear magnetic resonance, ash content). The two biomasses were found to have a different impact on the rheological behavior of the compounds and the extrusion process overall stability. When comparing the complex viscosity of neat PLA to the biomass/PLA compounds, the integration of wood powder increased the complex viscosity of the compound, whereas the integration of rice husk powder decreased it. This significant difference in rheological behavior was attributed to the higher specific surface area (and chemical reactivity) of the rice husk particles and the presence of silica in rice husks compared to the wood powder. Color variations were also observed. Despite the biomass filler and rheological behavior differences, the mechanical properties of the 3D printed samples were similar and predominantly affected by the printing direction.