RESUMO
A highly sensitive avalanche photodetector (APD) is fabricated by utilizing the avalanche multiplication mechanism in black phosphorus (BP), where a strong avalanche multiplication of electron-hole pairs is observed. Owing to the small bandgap (0.33 eV) of the multilayer BP, the carrier multiplication occurs at a significantly lower electric field than those of other 2D semiconductor materials. In order to further enhance the quantum efficiency and increase the signal-to-noise (S/N) ratio, Au nanoparticles (NPs) are integrated on the BP surface, which improves the light absorption by plasmonic effects. The BP-Au-NPs structure effectively reduces both dark current (≈10 times lower) and onset of avalanche electric field, leading to higher carrier multiplication, photogain, quantum efficiency, and S/N ratio. For the BP-Au-NPs APD, it is obtained that the external quantum efficiency (EQE) is 382 and the responsivity is 160 A W-1 at an electric field of 5 kV cm-1 (Vd ≈ 3.5 V, note that for the BP APD, EQE = 4.77 and responsivity = 2 A W-1 obtained at the same electric field). The significantly increased performance of the BP APD is promising for low-power-consumption, high-sensitivity, and low-noise photodevice applications, which can enable high-performance optical communication and imaging systems.
RESUMO
A generalized scheme for the fabrication of high performance photodetectors consisting of a p-type channel material and n-type nanoparticles is proposed. The high performance of the proposed hybrid photodetector is achieved through enhanced photoabsorption and the photocurrent gain arising from its effective charge transfer mechanism. In this paper, the realization of this design is presented in a hybrid photodetector consisting of 2D p-type black phosphorus (BP) and n-type molybdenum disulfide nanoparticles (MoS2 NPs), and it is demonstrated that it exhibits enhanced photoresponsivity and detectivity compared to pristine BP photodetectors. It is found that the performance of hybrid photodetector depends on the density of NPs on BP layer and that the response time can be reduced with increasing density of MoS2 NPs. The rising and falling times of this photodetector are smaller than those of BP photodetectors without NPs. This proposed scheme is expected to work equally well for a photodetector with an n-type channel material and p-type nanoparticles.
RESUMO
Various photodetectors showing extremely high photoresponsivity have been frequently reported, but many of these photodetectors could not avoid the simultaneous amplification of dark current. A gate-controlled graphene-silicon Schottky junction photodetector that exhibits a high on/off photoswitching ratio (≈104 ), a very high photoresponsivity (≈70 A W-1 ), and a low dark current in the order of µA cm-2 in a wide wavelength range (395-850 nm) is demonstrated. The photoresponsivity is ≈100 times higher than that of existing commercial photodetectors, and 7000 times higher than that of graphene-field-effect transistor-based photodetectors, while the dark current is similar to or lower than that of commercial photodetectors. This result can be explained by a unique gain mechanism originating from the difference in carrier transport characteristics of silicon and graphene.
RESUMO
High-pressure annealing in oxygen ambient at low temperatures (â¼300 °C) was effective in improving the performance of graphene field-effect transistors. The field-effect mobility was improved by 45% and 83% for holes and electrons, respectively. The improvement in the quality of Al2O3 and the reduction in oxygen-related charge generation at the Al2O3-graphene interface, are suggested as the reasons for this improvement. This process can be useful for the commercial implementation of graphene-based electronic devices.
RESUMO
We report on a saw-shaped electrode architecture ZnO thin film transistor (TFT), which effectively increases the channel width. The contact line of the saw-shaped electrode is almost twice as long at the contact metal/ZnO channel junction. We experimentally observed an enhancement in the output drive current by 50% and a reduction in the contact resistance by over 50%, when compared to a typically shaped electrode ZnO TFT consuming the same chip area. This performance enhancement is attributed to the extension of the channel width. This technique can contribute to device performance enhancement, and in particular reduce the contact resistance, which is a serious challenge.
RESUMO
The long-term stability and superior device reliability through the use of delicately designed metal contacts with two-dimensional (2D) atomic-scale semiconductors are considered one of the critical issues related to practical 2D-based electronic components. Here, we investigate the origin of the improved contact properties of alloyed 2D metal-semiconductor heterojunctions. 2D WSe2-based transistors with mixed transition layers containing van der Waals (M-vdW, NbSe2/WxNb1-xSe2/WSe2) junctions realize atomically sharp interfaces, exhibiting long hot-carrier lifetimes of approximately 75,296 s (78 times longer than that of metal-semiconductor, Pd/WSe2 junctions). Such dramatic lifetime enhancement in M-vdW-junctioned devices is attributed to the synergistic effects arising from the significant reduction in the number of defects and the Schottky barrier lowering at the interface. Formation of a controllable mixed-composition alloyed layer on the 2D active channel would be a breakthrough approach to maximize the electrical reliability of 2D nanomaterial-based electronic applications.
RESUMO
Heterostructures of compositionally and electronically variant two-dimensional (2D) atomic layers are viable building blocks for ultrathin optoelectronic devices. We show that the composition of interfacial transition region between semiconducting WSe2 atomic layer channels and metallic NbSe2 contact layers can be engineered through interfacial doping with Nb atoms. WxNb1-xSe2 interfacial regions considerably lower the potential barrier height of the junction, significantly improving the performance of the corresponding WSe2-based field-effect transistor devices. The creation of such alloyed 2D junctions between dissimilar atomic layer domains could be the most important factor in controlling the electronic properties of 2D junctions and the design and fabrication of 2D atomic layer devices.
RESUMO
We have investigated the effects of metal decoration on the gas-sensing properties of a device with two-dimensional (2D) molybdenum disulfide (MoS2) flake channels and graphene electrodes. The 2D hybrid-structure device sensitively detected NO2 gas molecules (>1.2 ppm) as well as NH3 (>10 ppm). Metal nanoparticles (NPs) could tune the electronic properties of the 2D graphene/MoS2 device, increasing sensitivity to a specific gas molecule. For instance, palladium NPs accumulate hole carriers of graphene/MoS2, electronically sensitizing NH3 gas molecules. Contrarily, aluminum NPs deplete hole carriers, enhancing NO2 sensitivity. The synergistic combination of metal NPs and 2D hybrid layers could be also applied to a flexible gas sensor. There was no serious degradation in the sensing performance of metal-decorated MoS2 flexible devices before/after 5000 bending cycles. Thus, highly sensitive and endurable gas sensor could be achieved through the metal-decorated 2D hybrid-structure, offering a useful route to wearable electronic sensing platforms.
RESUMO
Organic semiconductors are key building blocks for future electronic devices that require unprecedented properties of low-weight, flexibility, and portability. However, the low charge-carrier mobility and undesirable processing conditions limit their compatibility with low-cost, flexible, and printable electronics. Here, we present significantly enhanced field-effect mobility (µ(FET)) in semiconducting polymers mixed with boron-doped carbon nanotubes (B-CNTs). In contrast to undoped CNTs, which tend to form undesired aggregates, the B-CNTs exhibit an excellent dispersion in conjugated polymer matrices and improve the charge transport between polymer chains. Consequently, the B-CNT-mixed semiconducting polymers enable the fabrication of high-performance FETs on plastic substrates via a solution process; the µFET of the resulting FETs reaches 7.2 cm(2) V(-1) s(-1), which is the highest value reported for a flexible FET based on a semiconducting polymer. Our approach is applicable to various semiconducting polymers without any additional undesirable processing treatments, indicating its versatility, universality, and potential for high-performance printable electronics.
RESUMO
The structure and process of the graphene/Si heterojunction near-infrared photodetector were optimized to enhance the operating speed limit. The introduction of a well-designed structure improved the rise time from 12.6 µs to 115 ns, albeit at the expense of the responsivity, which decreased from 1.25 A W-1 to 0.56 A W-1. Similarly, the falling time was improved from 38 µs to 288 ns with a sacrifice in responsivity from 1.25 A W-1 to 0.29 A W-1, achieved through the introduction of Ge-induced defect-recombination centers within the well. Through a judicious well design and the introduction of recombination defect centers, the minimum pulse width could be improved from 50.6 µs to 435 ns, facilitating 2 MHz operation. This represents more than 100 times increase compared to previously reported graphene and graphene/Si hybrid photodetectors.
RESUMO
A highly flexible and transparent transistor is developed based on an exfoliated MoS2 channel and CVD-grown graphene source/drain electrodes. Introducing the 2D nanomaterials provides a high mechanical flexibility, optical transmittance (â¼74%), and current on/off ratio (>10(4)) with an average field effect mobility of â¼4.7 cm(2) V(-1) s(-1), all of which cannot be achieved by other transistors consisting of a MoS2 active channel/metal electrodes or graphene channel/graphene electrodes. In particular, a low Schottky barrier (â¼22 meV) forms at the MoS2 /graphene interface, which is comparable to the MoS2 /metal interface. The high stability in electronic performance of the devices upon bending up to ±2.2 mm in compressive and tensile modes, and the ability to recover electrical properties after degradation upon annealing, reveal the efficacy of using 2D materials for creating highly flexible and transparent devices.
RESUMO
The intrinsic photo-response of chemical vapor deposited (CVD) graphene photodetectors were investigated after eliminating the influence of photodesorption using an atomic layer deposited (ALD) Al2O3 passivation layer. A general model describing the intrinsic photocurrent generation in a graphene is developed using the relationship between the device dimensions and the level of intrinsic photocurrent under UV illumination.
RESUMO
The feasibility of a high speed ferroelectric graphene memory device using a ferroelectric polymer (PVDF-TrFE)/graphene stack has been demonstrated. The conductivity of this metal-ferroelectric-graphene (MFG) device could be modulated up to 775% with a very fast programming speed down to 10 ns. Also, programmed states were maintained up to 1000 s with endurance over 1000 cycles. In addition to demonstrating a single memory device, the array-level integration and cell write/read functionality of a 4 × 4 MFG array adopting a graphene bit line has also been confirmed to show the feasibility of MFG memory.
RESUMO
Efforts to develop scalable learning algorithms for implementation of networks of spiking neurons in silicon have been hindered by the considerable footprints of learning circuits, which grow as the number of synapses increases. Recent developments in nanotechnologies provide an extremely compact device with low-power consumption.In particular, nanoscale resistive switching devices (resistive random-access memory (RRAM)) are regarded as a promising solution for implementation of biological synapses due to their nanoscale dimensions, capacity to store multiple bits and the low energy required to operate distinct states. In this paper, we report the fabrication, modeling and implementation of nanoscale RRAM with multi-level storage capability for an electronic synapse device. In addition, we first experimentally demonstrate the learning capabilities and predictable performance by a neuromorphic circuit composed of a nanoscale 1 kbit RRAM cross-point array of synapses and complementary metal-oxide-semiconductor neuron circuits. These developments open up possibilities for the development of ubiquitous ultra-dense, ultra-low-power cognitive computers.
Assuntos
Eletrônica/instrumentação , Modelos Neurológicos , Nanotecnologia/instrumentação , Redes Neurais de Computação , Sinapses , SilícioRESUMO
The benefits of multi-layer graphene (MLG) capping on Cu interconnects have been experimentally demonstrated. The resistance of MLG capped Cu wires improved by 2-7% compared to Cu wires. The breakdown current density increased by 18%, suggesting that the MLG can act as an excellent capping material for Cu interconnects, improving the reliability characteristics. With a proper process optimization, MLG capped Cu interconnects could become a promising technology for high density back end-of-line interconnects.
RESUMO
A new touch sensor device has been demonstrated with molybdenum disulfide (MoS2) field effect transistors stacked with a piezoelectric polymer, polyvinylidene fluoride-trifluoroethylene (PVDF-TrFE). The performance of two device stack structures, metal/PVDF-TrFE/MoS2 (MPM) and metal/PVDF-TrFE/Al2O3/MoS2 (MPAM), were compared as a function of the thickness of PVDF-TrFE and Al2O3. The sensitivity of the touch sensor has been improved by two orders of magnitude by reducing the charge scattering and enhancing the passivation effects using a thin Al2O3 interfacial layer. Reliable switching behavior has been demonstrated up to 120 touch press cycles.
RESUMO
A reconfigurable passive device that can manipulate its resonant frequency by controlling its quantum capacitance value without requiring complicated equipment has been experimentally investigated by modifying the Fermi level of large-area graphene using an external electric field. When the total capacitance change, caused by the gate bias in the passive graphene device, was increased to 60% compared to the initial state, a 6% shift in the resonant frequency could be achieved. While the signal characteristics of the graphene antenna are somewhat inferior compared to the conventional metal antenna, simplifying the device structure allowed reconfigurable characteristics to be implemented by using only the gate bias change.
RESUMO
Carbon quantum dots (CQDs) have gained tremendous attention due to their pertinence in diverse application fields. Herein, we report the application of nitrogen-doped CQDs (N-CQDs) for the sensitive detection of reactive oxygen species (ROS) in vitro. The N-CQDs were synthesized via a rapid, one-pot, cost-effective and environmentally friendly approach, and exhibited amphibious solubility in solvents with a wide range of relative polarities from 1 to 0.4. Spectroscopic and microscopic techniques were used to accomplish the functional, morphological, and optical characterization of these nanoparticles. The as-synthesized luminous N-CQDs reproducibly demonstrated an average size distribution with a diameter of 5-6 nm. Their suitability for multiple other applications, such as metal sensing, confidential information inscription, hosting on cellulose materials with long-standing stability, designing polysaccharide molds flashing bright fluorescence, fingerprint imprinting, and in vitro bioimaging has also been exhibited. The plausible mechanism of peroxide induced fluorescence quenching of CQDs is presented. Treatment of human neuroblastoma cells SH-SY5Y with 1000 µg mL-1 N-CQDs demonstrated excellent (â¼100%) cell viability. An empirical relation between fluorescent intensity of N-CQDs as a function of the concentration of oxidants inside single-cells has been established for the first time.
Assuntos
Neuroblastoma , Pontos Quânticos , Humanos , Pontos Quânticos/química , Espécies Reativas de Oxigênio , Carbono/química , Nitrogênio/química , Micro-Ondas , Corantes Fluorescentes/químicaRESUMO
A p-type ternary logic device with a stack-channel structure is demonstrated using an organic p-type semiconductor, dinaphtho[2,3-b:2',3'-f]thieno[3,2-b]thiophene (DNTT). A photolithography-based patterning process is developed to fabricate scaled electronic devices with complex organic semiconductor channel structures. Two layers of thin DNTT with a separation layer are fabricated via the low-temperature deposition process, and for the first time, p-type ternary logic switching characteristics exhibiting zero differential conductance in the intermediate current state are demonstrated. The stability of the DNTT stack-channel ternary logic switch device is confirmed by implementing a resistive-load ternary logic inverter circuit.
RESUMO
We investigated the threshold voltage instability induced by gate bias (V(G)) stress in ZnO nanowire (NW) field effect transistors (FETs). By increasing the V(G) sweep ranges and repeatedly measuring the electrical characteristics of the ZnO NW FETs, the V(G) stress was produced in the dielectric layer underneath the ZnO NW. Consequently, the electrical conductance of the ZnO NW FETs decreased, and the threshold voltage shifted towards the positive V(G) direction. This threshold voltage instability induced by the V(G) stress is associated with the trapping of charges in the interface trap sites located in the ZnO NW-dielectric interface. Our study will be helpful for understanding the stability of ZnO NW FETs during repetitive operations.