Photonic Doppler velocimetry for high-speed fragment generator measurements.

We developed a modified photonic Doppler velocimetry (PDV) configuration which possesses the ability to record wide-range velocity information to evaluate composite material fracture behavior. With the laminate and tunnel design of a fragment generator, the controllable parameters such as fragment size and applied voltage can provide the flexibility for dynamic evaluation under different momentum conditions. We obtained velocity profiles using continuous wavelet transforms and by using our proposed velocity line tracing algorithm. Simulated heterodyne signals and surface morphology of fractures were examined to verify the heterodyne signals. We observed that the obtained tunnel-end velocity of the fragment generator was proportional to the applied voltage.

Measurement of LED chips using a large-area silicon photodiode.

We propose the output power measurement of bare-wafer/chip light-emitting diodes (LEDs) using a large-area silicon (Si) photodiode with a simple structure and high accuracy relative to the conventional partial flux measurement using an integrating sphere. To obtain the optical characteristics of the LED chips measured using the two methods, three-dimensional ray-trace simulations are used to perform the measurement deviations owing to the chip position offset or tilt angle. The ray-tracing simulation results demonstrate that the deviation of light remaining in the integrating sphere is approximately 65% for the vertical LED chip and 53% for the flip-chip LED chip if the measurement distance in partial flux method is set to be 5-40 mm. By contrast, the deviation of light hitting the photodiode is only 15% for the vertical LED chip and 23% for the flip-chip LED chip if the large-area Si photodiode is used to measure the output power with the same measurement distance. As a result, the large-area Si photodiode method practically reduces the output power measurement deviations of the bare-wafer/chip LED, so that a high-accuracy measurement can be achieved in the mass production of the bare-wafer/chip LED without the complicated integrating sphere structure.

Generating a sub-wavelength Bessel-like light beam using a tapered hollow tube.

We present a series of sub-wavelength annular aperture (SAA) structures with annular width equal to the tip of a tapered hollow tube, which was fabricated using a heat-pulled method. The light beams emitted from the SAA-like structures created by the tapered hollow tube produced light beams characteristic of Bessel beams. We obtained a sub-micrometer focal spot with a depth-of-focus larger than 7 µm and identified the proper structure parameters needed to generate Bessel-like light beams. Our new design has potential application to areas such as optical lithography, optical trapping, and the fabrication of high aspect ratio structures.

Integrating fault tolerance algorithm and circularly polarized ellipsometer for point-of-care applications.

A circularly polarized ellipsometer was developed to enable real-time measurements of the optical properties of materials. Using a four photo-detector quadrature configuration, a phase modulated ellipsometer was substantially miniaturized which has the ability to achieve a high precision detection limit. With a proven angular resolution of 0.0001 deg achieved by controlling the relative positions of a triangular prism, a paraboloidal and a spherical mirror pair, this new ellipsometer possesses a higher resolution than traditional complex mechanically controlled configurations. Moreover, the addition of an algorithm, FTA (fault tolerance algorithm) was adopted to compensate for the imperfections of the opto-mechanical system which can decrease system measurement reliability. This newly developed system requires only one millisecond or less to complete the measurement task without having to adopt any other modulation approach. The resolution achieved can be as high as 4x10(-7) RIU (refractive index unit) which is highly competitive when compared with other commercially available instruments. Our experimental results agreed well with the simulation data which confirms that our quadrature-based circularly polarized ellipsometer with FTA is an effective tool for precise detection of the optical properties of thin films. It also has the potential to be used to monitor the refractive index change of molecules in liquids.

Laser ablation of silicon using a Bessel-like beam generated by a subwavelength annular aperture structure.

Using a femtosecond laser incident to an oxide-metal-oxide film engraved with a subwavelength annular aperture (SAA) structure, we generated a Bessel-like beam to ablate silicon. Experimental results show that the silicon can be ablated with a 0.05 J/cm(2) input ablation threshold at 120 fs pulse duration. We obtained a surface hole possessing a diameter less than 1 µm. Optical performance, including depth-of-focus and focal spot of the SAA structure, were simulated using finite-different time-domain calculations. We found that a far-field laser beam propagating through a SAA structure possesses a submicrometer focal spot and high focus intensity. Our method can be easily adopted for surface machining in microfabrication applications.

Optically defined modal sensors incorporating spiropyran-doped liquid crystals with piezoelectric sensors.

We integrated a piezoelectric sensing layer lamina containing liquid crystals (LC) and spiropyran (SP) in a LC/SP mixture to create an optically reconfigurable modal sensor for a cantilever beam. The impedance of this LC/SP lamina was decreased by UV irradiation which constituted the underlying mechanism to modulate the voltage externally applied to the piezoelectric actuating layer. Illuminating a specific pattern onto the LC/SP lamina provided us with a way to spatially modulate the piezoelectric vibration signal. We showed that if an UV illuminated pattern matches the strain distribution of a specific mode, a piezoelectric modal sensor can be created. Since UV illumination can be changed in situ in real-time, our results confirm for the first time since the inception of smart sensors, that an optically tailored modal sensor can be created. Some potential applications of this type of sensor include energy harvesting devices, bio-chips, vibration sensing and actuating devices.

Enhanced detection of fluorescent nanospheres using two-channel radially polarized surface plasmon microscopy.

We detected single dye-stained latex nanospheres as small as 20 nm using a two-detection channel modified surface plasmon microscope. We found that a radially polarized incident beam leading to excitation of well-focused surface plasmons induces both fluorescence and elastic linear scattering from the spheres. The two complementary emitted signals were detected in parallel by the two separated channels, leading to well-colocalized images. We obtained high spatial resolutions for both channels down to 250 nm in the lateral direction and 300 nm along the longitudinal axis. We believe this multimodal microscope can be useful to track nano objects and to compensate for intermittent fluorescence, thanks to a permanently activated parallel scattering detection channel.

Effect of subwavelength annular aperture diameter on the nondiffracting region of generated Bessel beams.

A subwavelength annular aperture (SAA) made on metallic film and deposited on a glass substrate was fabricated by electron-beam lithography (EBL) and which was followed by a metal lift-off process to generate a long propagation range Bessel beam. We propose tuning the focal length and depth of focus (DOF) by changing the diameter of the SAA. We used finite-difference time domain (FDTD) simulations to verify our experimental data. We found that the position of the Bessel Beam focus spot (i.e. focal length) will be farther away from the SAA plane as the diameter of the SAA increases. In addition, the depth of focus (DOF) which is the length of the Bessel beam non-diffracting area, also increases as the diameter of the SAA expands.

Continuous numerical aperture properties of a cylindrically polarized light illuminated sub-wavelength annular aperture.

We investigated the process of focusing a radially polarized (RP) light beam through a sub-wavelength annular aperture (SAA). We found that the result was a non-diffraction doughnut-shaped light beam which propagates in free space. After analyzing the electric field component of the focus generated by the SAA structure, we identified the relationship between the focal field generated by the SAA. We then compared it to a case with a traditional objective lens. From our findings, we propose that a SAA structure can be viewed as a continuous numerical aperture optical element.

Propagation characteristics of silver and tungsten subwavelength annular aperture generated sub-micron non-diffraction beams.

We examined the optical properties such as propagation modes, focal length, side lobes, etc. of metallic subwavelength annular apertures (SAA) and used finite-difference time-domain (FDTD) simulation to compare our experimental findings. Using two different metals, silver and tungsten, we examined the different optical transmission properties of the two metallic SAA structures. The far-field propagation of the silver SAA structure was found to be a type of quasi-Bessel beam when compared with a quasi-Bessel beam generated by a perfect axicon. The propagation characteristics of these two beams were found to match qualitatively. The far-field transmitted light generated by the silver SAA structure was found to possess a 390 nm sub-micron focal spot with a 24 microm depth of focus, which was much smaller than the focal spot generated by a perfect axicon. We also found that a silver SAA structure can generate a sub-micron quasi- Bessel beam that has a much lower far-field side-lobe when compared to that of non-diffraction beams generated by a tungsten SAA structure.

Ellipsometric surface plasmon resonance.

We develop a new multifunctional optical biochip system that integrates an ellipsometer with a surface plasmon resonance (SPR) feature. This newly developed biochip biosensor, which we call ESPR for an ellipsometric SPR, provides us with a system to retrieve detailed information such as the optical properties of immobilized biomolecular monolayers, surface concentration variations of biomedical reactions, and kinetic affinity between biomolecules required for further biotech analysis. Our ESPR can also serve as both a research and development tool and a manufacturing tool for various biomedical applications.

Nanopatterning on silicon wafers using AFM-based lithography--for solar cells.

In this report, the nanopatterning method based on atomic force microscopy (AFM) with electrical bias to form the oxide patterns on silicon wafer is described. Under constant bias, 30 V, the linear pattern size is proportional to the rising humidity in the working environment. According to our experimental results, the sizes of the most circular nanopatterns are in the range from 50 nm to 70 nm depending on the applied bias and interaction time. In the results of evaluating the generation of oxidative production, the diameters and the number of oxide two dimensional nanopattern array, defaulted to 25 dots in 1 microm2, appeared in the AFM images have increasing tendency with the larger bias and the longer dwell time. Moreover, the imaging features of nanopatterns caused by bias 30 V have better performance than those by 10 V, and the dwell time only takes 0.015 s per dot.

Data on a new sensitivity-improved miniaturized label-free electrochemical biosensor.

This article presents a new sensitivity-improved electrochemical measurement architecture for cardiovascular disease (CVD) diagnosis by detecting CVD biomarkers, S100 beta protein and C-reactive protein (CRP). The new architecture includes a design for a new electrochemical measurement set-up, which improves the reaction conditions of chemical and biological molecules and incorporates a newly biochip design. With the new architecture, electrochemical measurement experiments were undertaken. The results obtained are related to the research article entitled "Improving sensitivity of a miniaturized label-free electrochemical biosensor using zigzag electrodes" [1].

Improving sensitivity of a miniaturized label-free electrochemical biosensor using zigzag electrodes.

Cardiovascular disease (CVD) is a leading cause of death among chronic diseases worldwide. Therefore, it is important to be able to detect CVD biomarkers early so that patients can be diagnosed properly and begin treatment as soon as possible. To detect biomarkers more conveniently, point-of-care (PoC) biosensors, which are easy to use and are of low cost, are becoming even more necessary. This paper focuses on developing a label-free electrochemical biosensor with high sensitivity for PoC applications to detect CVD biomarkers such as S100 beta proteins and C-reactive proteins (CRP). To meet the requirements of a PoC application and to improve the measurement sensitivity for detection purposes, a three-electrode configuration was miniaturized and fitted onto a biochip. Computer simulation of an electrolyte current density was used to investigate several potential effective possibilities. It was found that an electrolyte current density at an edge tip structure near the working electrode (WE) and counter electrode (CE) was higher than at other locations. A zigzag structure was then designed at the edge near the WE and CE positions. With this design, we can obtain a higher total electrolyte current. This newly-designed biochip was then used to measure the electrochemical feature. It was found that the measurement efficiency was also improved using this newly designed biochip.

Photorefractive crystal-based holographic interferometry system for full-field wave propagation metrology.

Although, photorefractive materials have been discovered for many years, research using pulsed laser as the light source and photorefractive material as the recording media to record a pulsed laser hologram have been scarce despite its vast application potential. A newly proposed optical configuration which adopts a Nd:YAG pulsed laser of 532nm wavelength as the light source and uses an iron-doped lithium niobate crystal as the recording media for holographic recording of an un-deformed specimen is presented. Real-time holographic interferometry was achieved by inducing repetitive impacts on the specimen through a precise piezoelectric impact hammer. With timing control better than microseconds, several interferograms created at each instance were obtained with each corresponding 9ns laser pulse. A five-step phase-shifting technology, median filter algorithm, and weighted iterative DFT phase unwrap algorithm were integrated to reconstruct the deformation information at each instance. Using a series of measured deformation data, surface wave propagation phenomenon on the specimen could be observed. Some of the potential applications for this newly developed pulsed laser holographic interferometry system are detailed.

Directional light beaming control by a subwavelength asymmetric surface structure.

We propose a direct experimental set-up to observe the directional beaming effect of surface plasmon. A single diffracted beam from an asymmetric-sided surface corrugation is demonstrated. A single subwavelength slit with an asymmetric structure was fabricated using a focused ion beam (FIB) onto a metal surface with a glass substrate. By means of surface plasmon (SP) diffraction, the directionality of the light can be changed by the period of the metallic gratings. We show corresponding numerical simulations achieved by a Rigorous Coupled-Wave Analysis (RCWA) method and a Finite-Difference Time-Domain (FDTD) method. The simulation results were in agreement with the experimental data.

Enhancement and tunability of active plasmonic by multilayer grating coupled emission.

The effect of coupled mode surface plasmon polaritons (SPPs) on the active emission of a nanostructure grating with organic semiconductor material, Alq(3), on the surface was investigated in this study. We report surface plasmon grating coupled emission (SPGCE) from excited organic layer on metal grating in both organic/metal (2-Layer) and organic/metal/organic/metal (4-Layer) structures. The dispersion relation was obtained from angle-resolved photoluminescence measurement. The resultant emission intensity can have up to 6 times enhancement on the 4- Layer device and the Full-Width Half-Maximum (FWHM) is less than 50 nm. The combination of SPPs on organic/metal interface allows specific directional emission and color appearance of Alq(3) fluorophores. Potential applications of such an active plasmonics with enhanced resonant energy emission due to interactions on the organic/metal nano-grating as biosensor were presented and discussed.

Dynamic response of glucagon/anti-glucagon pairs to pulling velocity and pH studied by atomic force microscopy.

We used atomic force microscopy (AFM) to measure the unbinding force between antigen coupled to an AFM tip and antibody coated on the substrate surface. Dynamic responses of glucagon/anti-glucagon pairs with multiple pull-off steps to pH and pulling velocity were studied by AFM. Force-distance curves of a specific glucagon-anti-glucagon interaction system with mono-, di-, and multi-unbinding events were recorded, which may be attributed to a single, sequential or multiple breaking of interacting bond(s) between glucagon and anti-glucagon. We studied the dynamic response of glucagon-anti-glucagon pairs to various pulling velocities (16.7-166.7 nm/s). It was found that the mean value of the unbinding force was shifted toward higher values with increasing pulling velocity at each pH. This indicates that the friction force between glucagon and anti-glucagon may contribute to the unbinding force. Moreover, the dynamic response of glucagon-anti-glucagon pairs to pH (4-10) with different pulling velocities was studied. Within the acid range, the bond strength between the glucagon/anti-glucagon complex showed a rapid increase from pH 4 to 7 and reached a maximum (256.4+/-48.9 pN at 166.7 nm/s) at neutrality, followed by a sharp decrease with increasing pH (pH 7-10). This could be attributed to the conformational change that occurred in glucagon when the pH value in solution was varied from the reference level at neutrality. This study demonstrated that the pH dependence of multiple antigen-antibody bond-rupture forces could be measured by a force-based AFM biosensor. Unraveling the relationship between inter-molecular force and intra-molecular conformational change in acid, neutral, and alkaline environments may provide new directions for future application of force measurements by AFM in proteomics or in the development of a clinical cantilever-based mechanical biosensor.

Atomic force microscopy: determination of unbinding force, off rate and energy barrier for protein-ligand interaction.

Recently, atomic force microscopy (AFM) based force measurements have been applied biophysically and clinically to the field of molecular recognition as well as to the evaluation of dynamic parameters for various interactions between proteins and ligands in their native environment. The aim of this review is to describe the use of the AFM to measure the forces that control biological interaction, focusing especially on protein-ligand and protein-protein interaction modes. We first considered the measurements of specific and non-specific unbinding forces which together control protein-ligand interactions. As such, we will look at the theoretical background of AFM force measurement curves for evaluating the unbinding forces of protein-ligand complexes. Three AFM model dynamic parameters developed recently for use in protein-ligand interactions are reviewed: (i) unbinding forces, (ii) off rates, and (iii) binding energies. By reviewing the several techniques developed for measuring forces between biological structures and intermolecular forces in the literature, we show that use of an AFM for these applications provides an excellent tool in terms of spatial resolution and lateral resolution, especially for protein-protein and protein-ligand interactions.

Multilayer modal actuator-based piezoelectric transformers.

An innovative, multilayer piezoelectric transformer equipped with a full modal filtering input electrode is reported herein. This modal-shaped electrode, based on the orthogonal property of structural vibration modes, is characterized by full modal filtering to ensure that only the desired vibration mode is excited during operation. The newly developed piezoelectric transformer is comprised of three layers: a multilayered input layer, an insulation layer, and a single output layer. The electrode shape of the input layer is derived from its structural vibration modal shape, which takes advantage of the orthogonal property of the vibration modes to achieve a full modal filtering effect. The insulation layer possesses two functions: first, to couple the mechanical vibration energy between the input and output, and second, to provide electrical insulation between the two layers. To meet the two functions, a low temperature, co-fired ceramic (LTCC) was used to provide the high mechanical rigidity and high electrical insulation. It can be shown that this newly developed piezoelectric transformer has the advantage of possessing a more efficient energy transfer and a wider optimal working frequency range when compared to traditional piezoelectric transformers. A multilayer piezoelectric, transformer-based inverter applicable for use in LCD monitors or portable displays is presented as well.