Generic character of charge and spin density waves in superconducting cuprates.

Charge density waves (CDWs) have been observed in nearly all families of copper-oxide superconductors. But the behavior of these phases across different families has been perplexing. In La-based cuprates, the CDW wavevector is an increasing function of doping, exhibiting the so-called Yamada behavior, while in Y- and Bi-based materials the behavior is the opposite. Here, we report a combined resonant soft X-ray scattering (RSXS) and neutron scattering study of charge and spin density waves in isotopically enriched La1.8−xEu0.2SrxCuO4 over a range of doping 0.07≤x≤0.20. We find that the CDW amplitude is temperature independent and develops well above experimentally accessible temperatures. Further, the CDW wavevector shows a nonmonotonic temperature dependence, exhibiting Yamada behavior at low temperature with a sudden change occurring near the spin ordering temperature. We describe these observations using a Landau­Ginzburg theory for an incommensurate CDW in a metallic system with a finite charge compressibility and spin-CDW coupling. Extrapolating to high temperature, where the CDW amplitude is small and spin order is absent, our analysis predicts a decreasing wavevector with doping, similar to Y and Bi cuprates. Our study suggests that CDW order in all families of cuprates forms by a common mechanism.

P2-Type Moisture-Stable and High-Voltage-Tolerable Cathodes for High-Energy and Long-Life Sodium-Ion Batteries.

P2-Na0.67Ni0.33Mn0.67O2 represents a promising cathode for Na-ion batteries, but it suffers from severe structural degradation upon storing in a humid atmosphere and cycling at a high cutoff voltage. Here we propose an in situ construction to achieve simultaneous material synthesis and Mg/Sn cosubstitution of Na0.67Ni0.33Mn0.67O2 via one-pot solid-state sintering. The materials exhibit superior structural reversibility and moisture insensitivity. In-operando XRD reveals an essential correlation between cycling stability and phase reversibility, whereas Mg substitution suppressed the P2-O2 phase transition by forming a new Z phase, and Mg/Sn cosubstitution enhanced the P2-Z transition reversibility benefiting from strong Sn-O bonds. DFT calculations disclosed high chemical tolerance to moisture, as the adsorption energy to H2O was lower than that of the pure Na0.67Ni0.33Mn0.67O2. A representative Na0.67Ni0.23Mg0.1Mn0.65Sn0.02O2 cathode exhibits high reversible capacities of 123 mAh g-1 (10 mA g-1), 110 mAh g-1 (200 mA g-1), and 100 mAh g-1 (500 mA g-1) and a high capacity retention of 80% (500 mA g-1, 500 cycles).

All-Oxide Transparent Photodetector Array for Ultrafast Response through Self-Powered Excitonic Photovoltage Operation.

Can photodetectors be transparent and operate in self-powered mode? Is it possible to achieve invisible electronics, independent of the external power supply system, for on-site applications? Here, a ZnO/NiO heterojunction-based high-functional transparent ultraviolet (UV) photodetector operating in the self-powered photovoltaic mode with outstanding responsivity and detectivity values of 6.9 A W-1 and 8.0 × 1012 Jones, respectively, is reported. The highest IUV /Idark value of 8.9 × 104 is attained at a wavelength of 385 nm, together with a very small dark current value of 9.15 × 10-12 A. A large-scale sputtering method is adopted to deposit the heterostructure of n-ZnO and p-NiO sequentially. This deposition instinctively forms an abrupt junction, resulting in a high-quality heterojunction device. Moreover, developing a ZnO/NiO-heterojunction-based 4 × 5 matrix array with an output photovoltage of 4.5 V is preferred for integrating photodetectors into sensing and imaging systems. This transparent UV photodetector exhibits the fastest photo-response time (83 ns) reported for array configurations, which is achieved using an exciton-induced photovoltage based on a neutral donor-bound exciton. Overall, this study provides a simple method for achieving a high-performance large-scale transparent UV photodetector with a self-powered array configuration.

Image stitching using an electrowetting-based liquid prism with a fabrication method.

In this paper, we propose a new method for image stitching using an electrowetting-based liquid prism. Several images were obtained by adjusting the voltages applied to four sidewalls of the liquid prism, and a panoramic image was achieved through an image stitching algorithm. The relationship between the tilting angle of the liquid prism and the normal vector of the liquid-liquid interface was presented. Novel fabrication method has been proposed to improve the performance of the liquid prism, including the addition of a new structure to prevent oil isolation, plastic chamber material, plastic laser cutting, and oil selection. The fabricated liquid prism has a size of 5 × 5 × 8 mm, a maximum beam steering angle of ±10.5 °, a response time of 19.1 ms, and a resolution of 14.25 lp/mm. The required number of images according to the overlapping area was presented through the simulation, and the image stitching using two or three images was demonstrated.

Emerging Roles of BRD7 in Pathophysiology.

Bromodomain is a conserved structural module found in many chromatin-associated proteins. Bromodomain-containing protein 7 (BRD7) is a member of the bromodomain-containing protein family, and was discovered two decades ago as a protein that is downregulated in nasopharyngeal carcinoma. Since then, BRD7 has been implicated in a variety of cellular processes, including chromatin remodeling, transcriptional regulation, and cell cycle progression. Decreased BRD7 activity underlies the pathophysiological properties of various diseases in different organs. BRD7 plays an important role in the pathogenesis of many cancers and, more recently, its roles in the regulation of metabolism and obesity have also been highlighted. Here, we review the involvement of BRD7 in a variety of pathophysiological conditions, with a focus on glucose homeostasis, obesity, and cancer.

Surface-to-Bulk Redox Coupling through Thermally Driven Li Redistribution in Li- and Mn-Rich Layered Cathode Materials.

Li- and Mn-rich (LMR) layered cathode materials have demonstrated impressive capacity and specific energy density thanks to their intertwined redox centers including transition metal cations and oxygen anions. Although tremendous efforts have been devoted to the investigation of the electrochemically driven redox evolution in LMR cathode at ambient temperature, their behavior under a mildly elevated temperature (up to ∼100 °C), with or without electrochemical driving force, remains largely unexplored. Here we show a systematic study of the thermally driven surface-to-bulk redox coupling effect in charged Li1.2Ni0.15Co0.1Mn0.55O2. We for the first time observed a charge transfer between the bulk oxygen anions and the surface transition metal cations under ∼100 °C, which is attributed to the thermally driven redistribution of Li ions. This finding highlights the nonequilibrium state and dynamic nature of the LMR material at deeply delithiated state upon a mild temperature perturbation.

Nonmechanical three-dimensional beam steering using electrowetting-based liquid lens and liquid prism.

In this paper, we present a system for nonmechanical three-dimensional beam steering using an electrowetting based liquid lens and liquid prism. The optical design of the presented system was modeled with Zemax and three-dimensional beam steering was simulated by changing the ROC of the lens and the apex angle of the prism. The liquid lens from Corning-Varioptic was used and the liquid prism was fabricated and these were combined. The liquid lens and liquid prism were filled with two immiscible liquids whose densities are the same. The liquid lens provides variable focal lengths as the applied voltage is changed. The diopter range of the liquid lens is from -3.9 D to 14.5 D. Beam steering on the x-axis, y-axis, and xy-axis was achieved by applying different voltages to four sidewalls of the liquid prism. The liquid prism has a beam steering angle of up to 11.6 °, 12 °, and 11.8 ° on x-axis, y-axis, and xy-axis, respectively. By combining the electrowetting actuated liquid lens and liquid prism, three-dimensional beam steering control including the z-axis direction was demonstrated.

Unconventional Charge Density Wave Order in the Pnictide Superconductor Ba(Ni_{1-x}Co_{x})_{2}As_{2}.

Ba(Ni_{1-x}Co_{x})_{2}As_{2} is a structural homologue of the pnictide high temperature superconductor, Ba(Fe_{1-x}Co_{x})_{2}As_{2}, in which the Fe atoms are replaced by Ni. Superconductivity is highly suppressed in this system, reaching a maximum T_{c}=2.3 K, compared to 24 K in its iron-based cousin, and the origin of this T_{c} suppression is not known. Using x-ray scattering, we show that Ba(Ni_{1-x}Co_{x})_{2}As_{2} exhibits a unidirectional charge density wave (CDW) at its triclinic phase transition. The CDW is incommensurate, exhibits a sizable lattice distortion, and is accompanied by the appearance of α Fermi surface pockets in photoemission [B. Zhou et al., Phys. Rev. B 83, 035110 (2011)PRBMDO1098-012110.1103/PhysRevB.83.035110], suggesting it forms by an unconventional mechanism. Co doping suppresses the CDW, paralleling the behavior of antiferromagnetism in iron-based superconductors. Our study demonstrates that pnictide superconductors can exhibit competing CDW order, which may be the origin of T_{c} suppression in this system.

Resolution of Electronic and Structural Factors Underlying Oxygen-Evolving Performance in Amorphous Cobalt Oxide Catalysts.

Non-noble-metal, thin-film oxides are widely investigated as promising catalysts for oxygen evolution reactions (OER). Amorphous cobalt oxide films electrochemically formed in the presence of borate (CoBi) and phosphate (CoPi) share a common cobaltate domain building block, but differ significantly in OER performance that derives from different electron-proton charge transport properties. Here, we use a combination of L edge synchrotron X-ray absorption (XAS), resonant X-ray emission (RXES), resonant inelastic X-ray scattering (RIXS), resonant Raman (RR) scattering, and high-energy X-ray pair distribution function (PDF) analyses that identify electronic and structural factors correlated to the charge transport differences for CoPi and CoBi. The analyses show that CoBi is composed primarily of cobalt in octahedral coordination, whereas CoPi contains approximately 17% tetrahedral Co(II), with the remainder in octahedral coordination. Oxygen-mediated 4 p-3 d hybridization through Co-O-Co bonding was detected by RXES and the intersite dd excitation was observed by RIXS in CoBi, but not in CoPi. RR shows that CoBi resembles a disordered layered LiCoO2-like structure, whereas CoPi is amorphous. Distinct domain models in the nanometer range for CoBi and CoPi have been proposed on the basis of the PDF analysis coupled to XAS data. The observed differences provide information on electronic and structural factors that enhance oxygen evolving catalysis performance.

Electro-wetting lenticular lens with improved diopter for 2D and 3D conversion using lens-shaped ETPTA chamber.

In this paper, we introduce a method for improving the lens diopter of 2D/3D convertible devices using electro-wetting. For stable operation, an electro-wetting device requires high dioptric performance and this was achieved using bi-convex liquid-liquid-solid phases. 1-Chloronaphthalene with a refractive index of 1.633 was used as an oil phase to achieve high diopters. ETPTA (trimethylolpropane ethoxylate triacrylate), a UV-sensitive material with low chemical reactivity to the 1-Chloronaphthalene, was used as a chamber material. This resulted in a diopter of 3030D for high quality multi-view images without unstable oil movement or trembling. The ETPTA was molded on a 0.3mm thick glass substrate that was coated with UV adhesive (NOA 81). The maximum diopter capable of stable operation was 3425D. 2D and 3D conversion and parallax motion were demonstrated.

Effect of oil on an electrowetting lenticular lens and related optical characteristics.

While there are many ways to realize autostereoscopic 2D/3D switchable displays, the electrowetting lenticular lens is superior due to the high optical efficiency and short response time. In this paper, we propose a more stable electrowetting lenticular lens by controlling the quantity of oil. With a large amount of oil, the oil layer was broken and the lenticular lens was damaged at relatively low voltage. Therefore, controlling the amount of oil is crucial to obtain the required dioptric power with stability. We proposed a new structure to evenly adjust the volume of oil and the dioptric power was measured by varying the volume of oil. Furthermore, the optical characteristics were finally analyzed in the electrowetting lenticular lens array with a proper amount of oil.

Improving the performance of an electrowetting lenticular lens array by using a thin polycarbonate chamber.

In this paper, we used a thin polycarbonate (PC) chamber to improve the performance of an electrowetting lenticular lens array. The polycarbonate chamber changed the radius of curvature (ROC) of the oil acting as a lens, which increased the dioptric power of the liquid lens to 1666.7D. The increase in dioptric power required a reduction in the distance between the optical center of the lens and the display pixels under the chamber, which was accomplished by reducing the thickness of the chamber. The optimal thickness of the chamber was determined to be 0.5mm. Using this thin PC chamber, transmittance and viewing angle were measured and compared with an electrowetting lenticular lens with a conventional 1mm poly methyl methacrylate (PMMA) chamber was done. Crosstalk which degrades clear 3D images, is an inevitable factor in lenticular lens type multi-view systems. With the 0.5mm PC chamber, the viewing zone was expanded and the ratio of the crosstalk area was reduced, which resulted in a clear 3D image. The new method of depositing the electrode layer also ensured the uniform operation of the liquid lens array.

Atomically engineered metal-insulator transition at the TiO2/LaAlO3 heterointerface.

We demonstrate that the atomic boundary conditions of simple binary oxides can be used to impart dramatic changes of state. By changing the substrate surface termination of LaAlO3 (001) from AlO2 to LaO, the room-temperature sheet conductance of anatase TiO2 films are increased by over 3 orders of magnitude, transforming the intrinsic insulating state to a high mobility metallic state, while maintaining excellent optical transparency.

Room Temperature Ferrimagnetism and Ferroelectricity in Strained, Thin Films of BiFe0.5Mn0.5O3.

Highly strained films of BiFe0.5Mn0.5O3 (BFMO) grown at very low rates by pulsed laser deposition were demonstrated to exhibit both ferrimagnetism and ferroelectricity at room temperature and above. Magnetisation measurements demonstrated ferrimagnetism (TC ∼ 600K), with a room temperature saturation moment (MS ) of up to 90 emu/cc (∼ 0.58 µB /f.u) on high quality (001) SrTiO3. X-ray magnetic circular dichroism showed that the ferrimagnetism arose from antiferromagnetically coupled Fe3+ and Mn3+. While scanning transmission electron microscope studies showed there was no long range ordering of Fe and Mn, the magnetic properties were found to be strongly dependent on the strain state in the films. The magnetism is explained to arise from one of three possible mechanisms with Bi polarization playing a key role. A signature of room temperature ferroelectricity in the films was measured by piezoresponse force microscopy and was confirmed using angular dark field scanning transmission electron microscopy. The demonstration of strain induced, high temperature multiferroism is a promising development for future spintronic and memory applications at room temperature and above.

Stimulatory effect of HGF-overexpressing adipose tissue-derived mesenchymal stem cells on thymus regeneration in a rat thymus involution model.

The thymus is the central lymphoid organ providing a unique and essential microenvironment for T-cell precursor development into mature functionally competent T-lymphocytes. Thus, it is important to develop the strategies for enhancing thymic regeneration from involution induced by a variety of clinical treatments and conditions. Hepatocyte growth factor (HGF) promotes proliferation in a variety of cell types. We have used stem cell-based HGF gene therapy to enhance regeneration from acute thymic involution. HGF-overexpressing human adipose tissue-derived mesenchymal stem cells (HGF-hATMSCs) were generated by liposomal transfection with the pMEX expression vector, constructed by inserting the HGF gene. Significantly increased HGF expression in these cells was confirmed by reverse transcription-polymerase chain reaction and an enzyme-linked immunosorbent assay. HGF produced by HGF-hATMSCs enhanced the proliferation of a mouse thymic epithelial cell line and the expression of interleukin-7 in vitro. We also examined the effect of HGF-hATMSCs on thymic regeneration in rats with acute thymic involution. Significant increases in thymus size and weight, as well as the number of thymocytes (especially, early thymocyte progenitors), were seen in the HGF-hATMSCs-treated rats compared to saline-treated control animals. A stimulatory effect of HGF-hATMSCs on thymic regeneration has therefore been shown, highlighting the clinical value of HGF-hATMSCs for treating thymic involution.

Thermal phenomena and size effects of Mg powder in combustion process.

Magnesium is a combustible metal that poses various safety risks, including fires and explosions. However, there are limited safety measures available to prevent and respond to potential fires and explosion incidents in the metal industry. In this study, the combustion process of Mg fires was closely examined using infrared thermal imaging, focusing on the effects of Mg powder size. For the experiment, Mg powder was burned by increasing the temperature to approximately 967.4 K using an ignition unit and controller equipped with a tungsten heater. Moreover, combustion velocity measurement experiments for Mg particle sizes of 75, 100, and 150 µm were conducted using the combustion velocity measurement device presented in the NFPA 484 standard. On combustion of Mg, flames are observed; smoke is emitted as demonstrated by thermal and flow visualization experiments. The combustion velocity measurement experiment results demonstrated that the greater the slope value (combustion velocity) for the combustion length over time, the faster is the combustion velocity, with the 75 µm particle size having the fastest combustion velocity. The results of this experiment can be utilized as references for Mg fire control design and to gain a better understanding of the scope of smoke and fire hazard investigation measures.

Van Der Waals Semiconductor Based Omnidirectional Bifacial Transparent Photovoltaic for Visual-Speech Photocommunication.

Omnidirectional photosensing is crucial in optoelectronic devices, enabling a wide field of view (wFoV) and leveraging potential applications for the Internet of Things in sensors, light fidelity, and photocommunication. The wFoV helps overcome the limitations of line-of-sight communication, and transparent photodetection becomes highly desirable as it enables the capture of optical information from various angles. Therefore, developing a photoelectric device with a 360° wFoV, ultra sensitivity to photons, power generation, and transparency is of utmost importance. This study utilizes a heterojunction of van der Waals SnS with Ga2 O3 to fabricate a transparent photovoltaic (TPV) device showing a 360° wFoV with bifacial onsite power production. SnS/Ga2 O3 heterojunction preparation consists of magnetron sputtering and is free from nanopatterning/nanostructuring to achieve the desired wFoV window device. The device exhibits a high average visible transmittance of 56%, generates identical power from bifacial illumination, and broadband fast photoresponse. Careful analysis of the device shows an ultra-sensitive photoinduced defect-modulated heterojunction and photocapacitance, revealed by the impedance spectroscopy, suggesting photon-flux driven charge diffusion. Leveraging the wFoV operation, the TPV embedded visual and speech photocommunication prototype demonstrated, aiming to help visually and auditory impaired individuals, promising an environmental-friendly sustainable future.

Transparent integrated pyroelectric-photovoltaic structure for photo-thermo hybrid power generation.

Thermal losses in photoelectric devices limit their energy conversion efficiency, and cyclic input of energy coupled with pyroelectricity can overcome this limit. Here, incorporating a pyroelectric absorber into a photovoltaic heterostructure device enables efficient electricity generation by leveraging spontaneous polarization based on pulsed light-induced thermal changes. The proposed pyroelectric-photovoltaic device outperforms traditional photovoltaic devices by 2.5 times due to the long-range electric field that occurs under pulse illumination. Optimization of parameters such as pulse frequency, scan speed, and illumination wavelength enhances power harvesting, as demonstrated by a power conversion efficiency of 11.9% and an incident-photon-to-current conversion efficiency of 200% under optimized conditions. This breakthrough enables reconfigurable electrostatic devices and presents an opportunity to accelerate technology that surpasses conventional limits in energy generation.

Divergent roles of the regulatory subunits of class IA PI3K.

The regulatory subunit of phosphatidylinositol 3-kinase (PI3K), known as p85, is a critical component in the insulin signaling pathway. Extensive research has shed light on the diverse roles played by the two isoforms of p85, namely p85α and p85ß. The gene pik3r1 encodes p85α and its variants, p55α and p50α, while pik3r2 encodes p85ß. These isoforms exhibit various activities depending on tissue types, nutrient availability, and cellular stoichiometry. Whole-body or liver-specific deletion of pik3r1 have shown to display increased insulin sensitivity and improved glucose homeostasis; however, skeletal muscle-specific deletion of p85α does not exhibit any significant effects on glucose homeostasis. On the other hand, whole-body deletion of pik3r2 shows improved insulin sensitivity with no significant impact on glucose tolerance. Meanwhile, liver-specific double knockout of pik3r1 and pik3r2 leads to reduced insulin sensitivity and glucose tolerance. In the context of obesity, upregulation of hepatic p85α or p85ß has been shown to improve glucose homeostasis. However, hepatic overexpression of p85α in the absence of p50α and p55α results in increased insulin resistance in obese mice. p85α and p85ß have distinctive roles in cancer development. p85α acts as a tumor suppressor, but p85ß promotes tumor progression. In the immune system, p85α facilitates B cell development, while p85ß regulates T cell differentiation and maturation. This review provides a comprehensive overview of the distinct functions attributed to p85α and p85ß, highlighting their significance in various physiological processes, including insulin signaling, cancer development, and immune system regulation.

The comparison of the accuracy of temporary crowns fabricated with several 3D printers and a milling machine.

PURPOSE: The purpose of this in vitro study was to compare the accuracy of various 3D printers and a milling machine. MATERIALS AND METHODS: The die model was designed using CAD (Autodesk Inventor 2018 sp3). The 30 µm cement space was given to the die and the ideal crown of the mandibular left first molar was designed using CAD (ExoCAD). The crowns were produced using the milling machine (Imes-icore 250i) and the 3D printers (Zenith U, Zenith D, W11) and they were divided into four groups. In all groups, the interior of each crown was scanned (Identica blue) and superimposed (Geomagic Control X) with the previously designed die. The difference between the die and the actual crown was measured at specific points. The Kruskal-Wallis test, the Mann-Whitney test, and Bonferroni's method were performed with a statistical analysis software (P < .008 in inter-group comparison P < .001 in intra-group comparison). RESULTS: In all groups, the center of the occlusal area and the anti-rotational dimple area showed significantly greater difference and the marginal area showed the smallest difference comparatively. The mean value of the difference in each area and the sum of the differences were higher in order of W11, Imes-icore 250i, Zenith D, and Zenith U. CONCLUSION: The digital light processing (DLP) method shows higher accuracy compared to the sereolithography (SLA) method using the same resin material.