Study on four metal organic frameworks as cleanup adsorbents for polycyclic aromatic hydrocarbons determined by GC-MS/MS.

A new application of MOFs as adsorbents in the cleanup procedure of polycyclic aromatic hydrocarbons (PAHs) in soils was explored. Four MOFs, specifically MIL-101(Cr), MIL-125(Ti), MIL-100(Fe) and UiO-66(Zr), were synthesized and characterized. A screening study was carried out to select the best adsorbent for the purification of sixteen PAHs in complex soil extract. It is found that the nature of metal ion, pore size, surface area and surface charge affect the purification efficiencies of the various MOFs. MIL-101(Cr) was then selected because of its best purification efficiency. The effects of amount of adsorbent, cleanup solvent and cleanup time on cleanup efficiency were investigated. Under the optimum conditions, the matrix effect of the target analytes was reduced by more than 65%. The method was then combined with ultrasonic extraction and quantitation by gas chromatography with triple quadrupole mass spectrometric detection. The method allows for the determination of PAHs in soils with linear in the range of 5-5000 ng g-1 and with LODs between 50 and 420 pg g-1. The method was applied to the analysis of (spiked) soil samples, and results compared well with the established EPA method. Graphical abstract Schematic presentation of metal organic frameworks (MOF) as cleanup adsorbents for purifying polycyclic aromatic hydrocarbons in soil organic matter (SOM) and further determined by gas chromatography with triple quadrupole mass spectrometry detection (GC-MS/MS).

Rapid preparation of methyltrimethoxy-modified magnetic mesoporous silica as an effective solid-phase extraction adsorbent.

A time-saving method was applied to synthesize methyltrimethoxy-modified magnetic mesoporous silica with or without p-toluenesulfonic acid as the catalyst for magnetic solid-phase extraction. The synthesized materials were systematically characterized. Results demonstrated that methyltrimethoxy modified magnetic mesoporous silica with p-toluenesulfonic acid as the catalyst has a relatively smaller aperture and extreme hydrophobicity (water contact angle of 135°). To evaluate the feasibility of these prepared materials as effective adsorbents, it was combined with gas chromatography and electron capture detection to determine 26 polychlorinated biphenyls in environmental water. The result revealed that methyltrimethoxy modified magnetic mesoporous silica with p-toluenesulfonic acid as the catalyst had the best extraction efficiency and recovery. Under the optimized extracted conditions, the proposed method showed good linearity within the concentration range of 5 to 200 ng/L with correlation coefficients of 0.9969 to 0.9999. The limits of detection and quantification based on signal-to-noise ratios of 3 and 10 were in the range of 0.16 to 0.91 and 0.52 to 3.0 ng/L, respectively. The polychlorinated biphenyl concentrations in environmental water samples were successfully determined using the developed method. PCB008 and PCB110 were 4.05 and 8.52 ng/L in Red-Star lake water (Hubei Province, China), respectively.

Facile preparation of hexadecyl-functionalized magnetic core-shell microsphere for the extraction of polychlorinated biphenyls in environmental waters.

Alkyl moieties which can retain target analytes due to their lipophilicity are important in sample preparation. In this work, hexadecyl-functionalized magnetic core-shell microspheres (Fe3O4@SiO2-C16) was successfully prepared by one-pot sol-gel method and used for magnetic solid-phase extraction of polychlorinated biphenyls (PCBs) in environmental water samples. Optimized preparation method was achieved by altering the adding moment of hexadecyl-silane. The resultant materials were systematically characterized by scanning electron microscope, transmission electron microscope, Fourier transform infrared spectroscopy, energy dispersive X-ray spectrometry, tensionmeter, and vibrating sample magnetometer. The results demonstrated that the optimized adsorbent exhibited core-shell structure, superparamagnetic (66 emu/g), and extremely hydrophobic (water contact angle of 122°) properties. To evaluate the extraction performance, the prepared material coupled with gas chromatography-triple quadrupole mass spectrometry (GC-MS/MS) was applied to determinate PCBs. The extraction conditions were optimized. Under the optimal conditions, the proposed method showed a good linearity range of 1-100 ng L-1 with correlation coefficients (R) of 0.9989-0.9993. Based on a signal-to-noise ratio of 3 and 10, the limits of detection (LODs) and limits of quantification (LOQs) were in the range 0.14-0.27 and 0.39-0.91 ng L-1, respectively. The intra- and inter-day relative standard deviations (RSDs) were less than 9.06%. The absolute recoveries of PCBs in spiked real water samples were in the range of 75.17 to 101.20%. Additionally, reusability and batch-to-batch reproducibility of the resultant material were acceptable with RSDs less than 5.64 and 3.25%, respectively. Graphical Abstract The synthesis procedure of Fe3O4@SiO2-C16 and determination of PCBs in water sample 129 × 50 mm (300 × 300 DPI).

Enhanced adsorption removal of anionic dyes via a facile preparation of amino-functionalized magnetic silica.

A novel amino-functionalized magnetic silica (Fe3O4@SiO2-NH2) was easily prepared via a one-step method integrating the immobilization of 3-aminopropyltriethoxysilane with a sol-gel process of tetraethyl orthosilicate into a single process. This showed significant improvement in the adsorption capacity of anionic dyes. The product (Fe3O4@SiO2-NH2) was characterized with scanning electron microscopy, Fourier transform infrared spectroscopy, energy dispersive X-ray spectrometry, zeta potential and vibrating sample magnetometry. The adsorption performance of Fe3O4@SiO2-NH2 was then tested by removing acid orange 10 (AO10) and reactive black 5 (RB5) from the aqueous solutions under various experimental conditions including initial solution pH, initial dye concentrations, reaction time and temperature. The results indicated that the maximum adsorption capacity of AO10 and RB5 on Fe3O4@SiO2-NH2 was 621.9 and 919.1 mg g-1 at pH 2, respectively. The sorption isotherms fit the Langmuir model nicely. Similarly, the sorption kinetic data were better fitted into the pseudo-second order kinetic model than the pseudo-first order model. In addition, the thermodynamic data demonstrated that the adsorption process was endothermic, spontaneous and physical. Furthermore, Fe3O4@SiO2-NH2 could be easily separated from aqueous solutions by an external magnetic field, and the preparation was reproducible.

Preparation of magnetic hydroxyapatite clusters and their application in the enrichment of phosphopeptides.

A novel strategy for the effective enrichment of phosphopeptides based on magnetic hydro-xyapatite (HAp) clusters was developed in the current study. The structure of HAp ensures its probable separation capability, including cation exchange with P-sites (negatively charged pairs of crystal phosphates), calcium coordination, anion exchange with C-sites (positively charged pairs of crystal calcium ions). The prepared magnetic HAp clusters showed good performance on the efficient enrichment of phosphopeptides from the digestion mixture of ß-casein and BSA. Compared to commercial HAp particles, the magnetic HAp clusters exhibited better selectivity toward phosphopeptides. In addition, the use of magnetic material greatly simplified the enrichment procedure, which avoided the tedious centrifugation steps in a typical phosphopeptides enrichment protocol. Finally, the material was successfully applied in the enrichment of phosphopeptides from human serum. Taken together, the efficient enrichment of the phosphopeptides by the easily prepared magnetic HAp clusters demonstrated a rapid and convenient strategy for the purification of phosphopeptides from complex samples, which may facilitate protein phosphorylation studies.

Accurate prediction bioaccessibility of PAHs in soil-earthworm system by novel magnetic solid phase extraction technique.

Conventional chemical extraction methods may lead to overestimate or underestimate bioaccessibility due to their inability to provide realistic kinetic information regarding PAHs in soils. In this study, we propose the use of magnetic solid phase extraction (MSPE) technique for assessing the bioaccessibility of PAHs in the soil-earthworm system. Firstly, a novel polydopamine-coated magnetic core-shell microspheres (Fe3O4-C16@PDA) was developed by a one-pot sol-gel and self-polymerization method. The PDA coatings not only enhance the hydrophilicity of material surfaces but also exhibit excellent biocompatibility. The maximum adsorption capacity of Fe3O4-C16@PDA for 16 PAHs was 52.72 mg g-1, indicating that the proposed material fulfills the assessment requirements for highly contaminated soil. To compare the measurement of PAHs and their uptake by earthworms (Eisenia fetida), experiments were conducted using four different soils with varying properties. The desorption kinetics data obtained from these experiments demonstrated that the capability of the MSPE in accurately predicting the bioavailable portions of PAHs. After a 28-day exposure, the best predictor of bioavailable PAHs in earthworms was MSPE method exhibited the highest correlation coefficient (R2 > 0.90), and its slopes in the four soils were 0.972, 0.961, 1.012, and 0.962, respectively, all close to 1. These results demonstrate that the MSPE method successfully mimics the conditions encountered in soil-earthworm systems and effectively assess bioaccessibility of PAHs in soils.

Rapid enrichment of phosphopeptides by SiO2-TiO2 composite fibers.

SiO2-TiO2 composite fibers, prepared by electrospinning, were successfully applied to the rapid enrichment of phosphopeptides using a lab-in-syringe approach for the first time. Because of their large surface area, mesoporous structure, extraordinary length and appropriate Lewis acidity, the as-prepared SiO2-TiO2 composite fibers exhibited high selectivity and capacity in the enrichment of phosphopeptides from the digestion mixture of ß-casein and bovine serum albumin (BSA), as well as human blood serum and nonfat milk. The targeted phosphopeptides could be easily enriched and detected even when the total amount of ß-casein was decreased to only 10 fmol, indicating the high detection sensitivity of this method. In addition, the whole enrichment extraction procedure can be finished in less than 3 min, which can avoid or decrease the degradation of endogenous phosphoproteins by proteases released ex vivo during time-consuming treatments. The developed method is rapid, cost-effective, selective, sensitive, operationally simple, and does not require any harsh conditions and intricate equipment, providing an ideal candidate for the enrichment of phosphopeptides from complex biological samples either in the lab or in the field.

Zirconium arsenate-modified magnetic nanoparticles: preparation, characterization and application to the enrichment of phosphopeptides.

Phosphorylation, one of the most important post-translational modifications of protein, plays a crucial role in a large number of biological processes. Large-scale identification of protein phosphorylation by mass spectrometry is still a challenging task because of the low abundance of phosphopeptides and sub-stoichiometry of phosphorylation. In this work, a novel strategy based on the specific affinity of zirconium arsenate to the phosphate group has been developed for the effective enrichment of phosphopeptides. Zirconium arsenate-modified magnetic nanoparticles (ZrAs-Fe(3)O(4)@SiO(2)) were prepared by covalent immobilization of zirconium arsenate on Fe(3)O(4)@SiO(2) magnetic nanoparticles under mild conditions, and characterized by transmission electron microscope (TEM), Fourier transform infrared (FT-IR) spectroscopy, energy dispersive X-ray spectroscopy (EDX) and vibrating sample magnetometer (VSM). The prepared ZrAs-Fe(3)O(4)@SiO(2) was applied for the selective enrichment of phosphopeptides from the digestion mixture of phosphoproteins and bovine serum albumin (BSA). Our results demonstrated that the ZrAs-Fe(3)O(4)@SiO(2) magnetic nanoparticles possess higher selectivity for phosphopeptides and better capture capability towards multiply-phosphorylated peptides than commercial zirconium dioxide (ZrO(2)), which has been widely employed for the enrichment of phosphopeptides. In addition, endogenous phosphopeptides from human serum can be effectively captured by ZrAs-Fe(3)O(4)@SiO(2) magnetic nanoparticles. It is the first report, to the best of our knowledge, in which the zirconium arsenate-modified magnetic nanoparticles were successfully applied to the enrichment of phosphopeptides, which offers the potential application of this new material in phosphoproteomics study.

Titanium-containing magnetic mesoporous silica spheres: effective enrichment of peptides and simultaneous separation of nonphosphopeptides and phosphopeptides.

Protein phosphorylation is a common posttranslational modification, and involved in many cellular processes. Like endogenous peptides, endogenous phosphopeptides contain many biomarkers of preclinical screening and disease diagnosis. In this work, titanium-containing magnetic mesoporous silica spheres were synthesized and applied for effective enrichment of peptides from both tryptic digests of standard proteins and human serum. Besides, the enriched peptides can be further separated into nonphosphopeptides and phosphopeptides by a simple elution. First, titanium-containing magnetic mesoporous silica spheres were synthesized by a sol-gel method and found to have high surface area, narrow pore size distribution, and useful magnetic responsivity. Then, as the prepared material was used for selective capturing of phosphopeptides, it demonstrated to have higher selectivity than commercial titanium dioxide. Moreover, via combination of size-exclusion mechanism, hydrophobic interaction, and affinity chromatography, titanium-containing magnetic mesoporous silica spheres were successfully applied to simultaneously extract and separate nonphosphopeptides and phosphopeptides from standard protein digestion and human serum.

Magnetic solid-phase extraction based on magnetic carbon nanotube for the determination of estrogens in milk.

In this work, a novel method for the fabrication of magnetic carbon nanotubes based on 'aggregation wrap' was proposed. When carbon nanotubes and magnetic nanoparticles were vortically mixed in a solvent, the magnetic nanoparticles were wrapped into the carbon nanotube bundles that formed during the aggregation process, leading to the formation of magnetic carbon nanotubes. Thus, the resultant material can be separated from the solvent rapidly and conveniently by a magnet. Our investigation demonstrated that the 'aggregation wrap' mechanism for the preparation of magnetic composite is also applicable to other self-aggregated micro/nanomaterials, including graphene, graphite, C(60), etc. To testify the feasibility of the magnetic composites in sample preparation, the resultant magnetic carbon nanotubes were applied as sorbents for magnetic solid-phase extraction (MSPE) of estrogens in milk samples. Under optimized conditions, a rapid, convenient and efficient method for the determination of estrogens in milk samples was established by the combination of MSPE with high-performance liquid chromatography with fluorescence detector. The linearity range of the proposed method was 5-2000 µg/L with correlation coefficients (R) of 0.9983-0.9994. The limit of detection (LOD) for three estrogens ranged from 1.21 to 2.35 µg/L. The intra- and inter-day relative standard deviations (RSDs) were <9.3%. The reproducibility of the MSPE with different batches of magnetic carbon nanotubes was acceptable with RSD values <3.6%.

Facile synthesis of polydivinylbenzene coated magnetic polydopamine coupled with pressurized liquid extraction for the extraction and cleanup of polycyclic aromatic hydrocarbons in soils.

Due to the trace levels of polycyclic aromatic hydrocarbons (PAHs) in soil and the complexity of soil matrices, effective sample pretreatment methods are of great significance to obtain accurate analytical results. In this paper, polydopamine (PDA) encapsulated Fe3O4 particles were used as seeds for in situ polymerization of divinylbenzene (DVB) to derive magnetic hybrid material Fe3O4@PDA@PDVB. Coupled with pressurized liquid extraction, Fe3O4@PDA@PDVB was investigated as a selective adsorbent for the extraction and cleanup of PAHs in soil. The prepared magnetic material was characterized and demonstrated to possess strong hydrophobicity and superparamagnetism. Under optimal conditions, Fe3O4@PDA@PDVB can effectively extract 15 PAHs from a 30% methanol solution within 2 min, and it is more selective for PAHs than for n-alkane in soil extracts. The matrix effect significantly decreased after extraction by the prepared material, which showed superiority to a silica gel column method (EPA 3630C Method). The developed method was linear (5-1000 ng g-1) with coefficient of determination (R2) ranging from 0.9986-0.9998, and the limits of detection were 0.13-0.54 ng g-1. Additionally, repetitive experiments indicated that the prepared material was reproducible and reusable with relative standard deviations below 8.4% and 8.6%, respectively. Finally, the new method was successfully employed to determine the concentrations of PAHs in genuine soil and standard reference material, and the results were comparable to those of widely utilized EPA methodology.

Polydopamine-coated polyethylene sieve plate as an efficient and convenient adsorption sink for the bioaccessibility prediction of PAHs in soils.

Bioaccessibility measurements of polycyclic aromatic hydrocarbons (PAHs) in soils are significant for exposure risk assessment. The current physicochemical methods require tedious operation processes, underestimate the actual risks, or are unsuitable for high organic content soils. In this work, an efficient and convenient method based on polydopamine-coated polyethylene sieve plate (PDA@PESP) and hydroxypropyl-ß-cyclodextrin (HPCD) was developed to predict the bioaccessibility of PAHs in multi-type soils. The PDA@PESP can be prepared via in situ self-polymerization, allowing to extract PAHs from HPCD solution quantitatively and rapidly. When applied to evaluate the bioaccessibility with PDA@PESP as an adsorption sink and HPCD as a diffusive carrier, the proposed method can significantly improve the extractable fraction of PAHs compared to single HPCD extraction in particular for high organic carbon content soil and high-ring PAHs. The desorption kinetics data indicated that the method can predict the bioaccessible fraction of PAHs. In addition, the method predicted a satisfactory accumulation into earthworms (Eisenia fetida) with a slope statistically approximated to 1. A highly significant linear regression (R2 = 0.95) was also found between the proposed method and Tenax desorption in historically contaminated soils, demonstrating that the method is an efficient and convenient approach for the bioaccessibility prediction of PAHs in soils.

Preparation of phenyl-modified magnetic silica as a selective magnetic solid-phase extraction adsorbent for polycyclic aromatic hydrocarbons in soils.

Accurate analysis of polycyclic aromatic hydrocarbons (PAHs) in soils remains a challenge due to the complexity of sample matrices. In this paper, phenyl-modified magnetic mesoporous silica (Fe3O4@mSiO2-Ph-PTSA) was synthesized with p-toluenesulfonic acid (PTSA) as the catalyst and used as a selective adsorbent for the clean-up of PAHs extracted from soils. The material prepared without PTSA as the catalyst (Fe3O4@mSiO2-Ph) was synthesized for comparison. The synthesized materials were first systematically characterized and evaluated. It was found that the grafting amount of the phenyl group onto Fe3O4@mSiO2-Ph-PTSA was higher than that onto Fe3O4@mSiO2-Ph. The extraction efficiency obtained by extracting PAHs from the extracted soil matrix solution demonstrated that Fe3O4@mSiO2-Ph-PTSA possessed a much higher extraction efficiency than that of Fe3O4@mSiO2-Ph, which can be attributed to the greater amount of phenyl groups grafted on Fe3O4@mSiO2 in the presence of the PTSA catalyst. Moreover, contrast experiments showed that Fe3O4@mSiO2-Ph-PTSA displayed higher selectivity towards PAHs than towards n-alkanes and that the π-π interaction played a key role in the adsorption process. In the presence of the soil extract matrix, the parameters affecting the extraction efficiency of Fe3O4@mSiO2-Ph-PTSA for PAHs were optimized. Under the optimal conditions, coupled with pressurized liquid extraction and gas chromatograph-mass spectrometer, the proposed method for the determination of PAHs in soils was linear in the range of 5-500 ng g-1, and the correlation coefficients (R) ranged between 0.9994 and 0.9999. The limits of detection (LODs) and limits of quantification (LOQs), which were based on signal-to-noise ratios of 3 and 10, respectively, were in the range of 0.07-0.41 ng g-1 and 0.24-1.37 ng g-1. The developed method displayed a better clean-up effect than that for silica gel column method, and the matrix effect markedly decreased compared to that of the uncleaned condition. Finally, the developed method was successfully applied for the detection of PAHs in environmental soils, and the data were consistent with the results obtained by the silica gel column method. The analytical results were also consistent with those for the real environment.

Perovskite for the highly selective enrichment of phosphopeptides.

Selective and effective enrichment of phosphopeptides from complex samples is essential in phosphoproteome study by mass spectrometry (MS). In this work, we compared perovskites (MgTiO3, CaTiO3, SrTiO3, BaTiO3 and CaZrO3) with metal oxides (ZrO2 and TiO2) in their capability for the selective enrichment of phosphopeptides. It was found here that perovskites exhibited higher selectivity towards phosphopeptides than commonly used ZrO2 and TiO2, even though they all have high affinity to phosphopeptides. As for perovskites, CaTiO3 exhibited better selectivity for enrichment of phosphopeptides than SrTiO3, MgTiO3, BaTiO3 and CaZrO3, which might be ascribed to their crystal structures and electrophilic abilities. Moreover, to further confirm the performance of CaTiO3, CaTiO3 and TiO2 were applied to the enrichment of phosphopeptides from tryptic digest of proteins of human Jurkat-T cell lysate, respectively. The results showed CaTiO3 has much higher selectivity than TiO2 in the enrichment of phosphopeptides from the complex biological sample. Taken together, here we show that CaTiO3 is an excellent material for the highly selective enrichment of phosphopeptides and it could be potentially used in the large-scale phosphoproteome study.

Sequential enrichment with titania-coated magnetic mesoporous hollow silica microspheres and zirconium arsenate-modified magnetic nanoparticles for the study of phosphoproteome of HL60 cells.

As one of the most important types of post-translational modifications, reversible phosphorylation of proteins plays crucial roles in a large number of biological processes. However, owing to the relatively low abundance and dynamic nature of phosphorylation and the presence of the unphosphorylated peptides in large excess, phosphopeptide enrichment is indispensable in large-scale phosphoproteomic analysis. Metal oxides including titanium dioxide have become prominent affinity materials to enrich phosphopeptides prior to their analysis using liquid chromatography-mass spectrometry (LC-MS). In the current study, we established a novel strategy, which encompassed strong cation exchange chromatography, sequential enrichment of phosphopeptides using titania-coated magnetic mesoporous hollow silica microspheres (TiO2/MHMSS) and zirconium arsenate-modified magnetic nanoparticles (ZrAs-Fe3O4@SiO2), and LC-MS/MS analysis, for the proteome-wide identification of phosphosites of proteins in HL60 cells. In total, we were able to identify 11,579 unique phosphorylation sites in 3432 unique proteins. Additionally, our results suggested that TiO2/MHMSS and ZrAs-Fe3O4@SiO2 are complementary in phosphopeptide enrichment, where the two types of materials displayed preferential binding of peptides carrying multiple and single phosphorylation sites, respectively.

Facile fabrication of reduced graphene oxide-encapsulated silica: a sorbent for solid-phase extraction.

In this study, a facile hydrothermal reduction strategy was developed for the preparation of reduced graphene oxide-encapsulated silica (SiO2@rGO). Compared with other conventional methods for the synthesis of SiO2@rGO, the proposed strategy endowed the obtained SiO2@rGO with larger amount of immobilized rGO. The prepared functionalized silica shows remarkable adsorption capacity toward chlorophenols (CPs) and peptides. When it was used as solid-phase extraction (SPE) sorbent, a superior recovery could be obtained compared to commercial sorbents, such as C18 silica, graphitized carbon black and carbon nanotubes. Based on these, the prepared material was used as SPE sorbent for the enrichment of CPs, and a method for the analysis of CPs in water samples was established by coupling SPE with high performance liquid chromatography-ultra violet detection (SPE-HPLC/UV). In addition, the obtained SiO2@rGO was further successfully extended to the enrichment of peptides in bovine serum albumin (BSA) digests.

Preparation of mesoporous silica embedded pipette tips for rapid enrichment of endogenous peptides.

Mesoporous silica embedded pipette tips (mSiO2-Tips) were successfully prepared by a simple method and applied to rapid enrichment of endogenous peptides for the first time. The prepared mSiO2-Tips showed low back pressure when solvent was pipetted up and down. As a result, mSiO2-Tip could selectively trap peptides and exclude high-MW proteins simultaneously based on size-exclusion mechanism due to the uniform mesopore structure of the sorbent bed. The in-pipette-tip SPE approach was proved to be easy-operation, sensitive and fast (less than 2 min) for the analysis of peptides, which was further successfully applied in the efficient enrichment of peptides from human plasma.

Preparation of titanium-grafted magnetic mesoporous silica for the enrichment of endogenous serum phosphopeptides.

As one of the most important post-translational modifications, reversible phosphorylation of protein plays crucial roles in a large number of biological processes. Moreover, endogenous phosphopeptides are also associated with certain human diseases. An efficient enrichment and separation method is the premise for successful identification and quantification of phosphopeptides. In this work, titanium grafted magnetic mesoporous silica (Fe3O4@Ti-mSiO2) was developed and applied for the enrichment of endogenous phosphopeptides. Fe3O4@Ti-mSiO2 particles were prepared by grafting titanocene dichloride on the inner walls of magnetic mesoporous silica and then being calcined to remove cyclopentadienyl ligand. The physicochemical properties of the prepared materials were characterized by energy dispersive X-ray spectroscopy (EDX), nitrogen adsorption-desorption analysis, X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). For selective enrichment of phosphopeptides, the prepared Fe3O4@Ti-mSiO2 particles were applied for tryptic digests of ß-casein, mixtures of ß-casein and bovine serum albumin (BSA), and low-fat milk. Finally, Fe3O4@Ti-mSiO2 was successfully applied for the enrichment of endogenous phosphopeptides from human serum.

Electrospinning-based synthesis of highly ordered mesoporous silica fiber for lab-in-syringe enrichment of plasma peptides.

Silica fiber with highly ordered mesoporous structure and continuously long fibrous property was synthesized on a large-scale for the first time. It can be applied to the rapid (less than 3 min) and effective enrichment of endogenous peptides with a novel lab-in-syringe approach.

Preparation of magnetic poly(diethyl vinylphosphonate-co-ethylene glycol dimethacrylate) for the determination of chlorophenols in water samples.

In this work, a novel type of magnetic polymer particle, magnetic poly(diethyl vinylphosphonate-co-ethylene glycol dimethacrylate) [Fe(3)O(4)@p(DEVP-co-EDMA)], was successfully synthesized and applied for the extraction and determination of chlorophenols in water samples by coupling with high-performance liquid chromatography (HPLC). Fe(3)O(4)@p(DEVP-co-EDMA) was synthesized by a simple seeded radical polymerization method and exhibited well-defined core-shell structure and good magnetic response ability. In addition, the magnetic polymer had the advantages of abundant adsorption sites and high enrichment efficiency. Due to the presence of PO group in the skeleton of polymer, the magnetic polymer material displayed excellent extraction performance for chlorophenols, such as 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP) and 2,4,6-trichlorophenol (2,4,6-TCP). Hydrophobic skeleton of the magnetic polymer also provided strong interaction with the target analytes, especially pentachlorophenol (PCP) which is a kind of non-polar chlorophenol. Desorption solution, pH of water sample, extraction time and desorption time, the amount of adsorbent, and the volume of desorption solution were optimized. Under the optimized conditions, the linear ranges of four chlorophenols were 2-500 ng/mL with the limits of detection (S/N=3) ranging from 0.20 to 0.34 ng/mL. The repeatability was investigated by evaluating the intra- and inter-day precisions with relative standard deviations (RSDs) lower than 15.0%. The recoveries for real water samples were in the range of 92.7-108.0%. Collectively, the results indicated that the novel Fe(3)O(4)@p(DEVP-co-EDMA) was successfully applied in the extraction and detection of chlorophenols from water samples, and the magnetic polymer particle showed potential applications in the analysis of polar compounds.