Construction of Stable Wide-Temperature-Range Proton Exchange Membranes by Incorporating a Carbonized Metal-Organic Frame into Polybenzimidazoles and Polyacrylamide Hydrogels.

Proton exchange membrane fuel cells (PEMFCs) are promising devices for clean power generation in fuel cell electric vehicles applications. The further request of high-efficiency and cost competitive technology make high-temperature proton exchange membranes utilizing phosphoric acid-doped polybenzimidazole be favored because they can work well up to 180 °C without extra humidifier. However, they face quick loss of phosphoric acid below 120 °C and resulting in the limits of commercialization. Herein UiO-66 derived carbon (porous carbon-ZrO2 ), comprising branched poly(4,4'-diphenylether-5,5'-bibenzimidazole) and polyacrylamide hydrogels self-assembly (BHC1-4) membranes for wide-temperature-range operation (80-160 °C) is presented. These two-phase membranes contained the hygroscopicity of polyacrylamide hydrogels improve the low-temperature proton conductivity, relatively enable the membrane to function at 80 °C. An excellent cell performance of BHC2 membrane with high peak power density of 265 and 656 mW cm-2 at both 80 and 160 °C can be achieved. Furthermore, this membrane exhibits high stability of frequency cold start-ups (from room temperature to 80 °C) and long-term cell test at 160 °C. The improvement of cell performance and stability of BHC2 membrane indicate a progress of breaking operated temperature limit in existing PEMFCs systems.

The antibacterial, cytotoxic, and flexural properties of a composite resin containing a quaternary ammonium monomer.

STATEMENT OF PROBLEM: The use of composite resin to restore teeth has increased substantially during the last decades. However, secondary caries and the fracture of restorations are the leading reasons for clinical restoration failure. Mechanically strong composite resins with caries-inhibition capabilities are needed. Although antibacterial dimethacrylate quaternary ammonium monomers have been synthesized, composite resin containing dimethacrylate quaternary ammonium monomers and glass fillers has rarely been reported. PURPOSE: The purpose of this in vitro study was to evaluate the possibility of the clinical use of an experimental composite resin containing urethane dimethacrylate quaternary ammonium compound (UDMQA-12) by investigating its antibacterial activity, cytotoxicity, flexural strength, and flexural modulus. MATERIAL AND METHODS: Antibacterial activity against Streptococcus mutans was investigated by means of direct contact test. The antibacterial activity of specimens after water immersion and saliva treatment was also tested. These were compared with a commercially available composite resin, Z250, and a glass ionomer cement, Fuji VII. Effects of the eluent from the experimental composite resin on the metabolic activity of human dental pulp cells were quantified. Disks of 1 mm in thickness and 15 mm in diameter were used in the antibacterial and cytotoxic tests. Flexural strength and flexural modulus were measured with a 3-point bend test with bars of 2×2×25 mm. Three commercially available composite resins (Filtek Z250, G-aenial Anterior, and G-aenial Posterior) were used as controls in the flexural test. RESULTS: Bacterial growth was inhibited on the experimental composite resin. After water immersion or saliva treatment, the experimental composite resin showed significant antibacterial effect compared with the conventional composite resin (P<.05). No significant difference was found in cytotoxicity between the experimental composite resin and the conventional composite resin (P＞.05), and a significantly higher cytotoxicity was shown by glass ionomer cement compared with the experimental composite resin and the conventional composite resin (P<.05). The conventional composite resin had the highest flexural strength and flexural modulus (P<.05), followed by the experimental composite resin, then G-ænial Posterior and G-ænial Anterior. CONCLUSIONS: The antibacterial experimental composite resin was biocompatible and had mechanical properties similar to those of some commercially available composite resins. It might, therefore, be useful in preventing the occurrence of secondary caries.

Optimizing the concentration of quaternary ammonium dimethacrylate monomer in bis-GMA/TEGDMA dental resin system for antibacterial activity and mechanical properties.

Four novel quaternary ammonium dimethacrylate monomers named IMQ (side alkyl chain length from 12 to 18) were synthesized with the aim to synthesize dental resin with antibacterial activity. All of IMQs were added into bis-GMA/TEGDMA dental resin system with a series of mass ratio (5, 10, and 20 wt%), double bond conversion (DC), flexural strength (FS), modulus of elasticity (FM) and biofilm formation inhibitory effect were studied. According to the results of DC, FS, FM, and the biofilm inhibitory effect, IMQ-16 containing polymer had the best comprehensive properties, and the optimal concentration of IMQ-16 in bis-GMA/TEGDMA dental resin would be in the range of 5-10 wt%.

Progress in the Preparation and Application of Inulin-Based Hydrogels.

Inulin, a natural polysaccharide, has emerged as a promising precursor for the preparation of hydrogels due to its biocompatibility, biodegradability, and structural versatility. This review provides a comprehensive overview of the recent progress in the preparation, characterization, and diverse applications of inulin-based hydrogels. Different synthesis strategies, including physical methods (thermal induction and non-thermal induction), chemical methods (free-radical polymerization and chemical crosslinking), and enzymatic approaches, are discussed in detail. The unique properties of inulin-based hydrogels, such as stimuli-responsiveness, antibacterial activity, and their potential as fat replacers, are highlighted. Special emphasis is given to their promising applications in drug delivery systems, especially for colon-targeted delivery, due to the selective degradation of inulin via colonic microflora. The ability to incorporate both hydrophilic and hydrophobic drugs further expands their therapeutic potential. In addition, the applications of inulin-based hydrogels in responsive materials, the food industry, wound dressings, and tissue engineering are discussed. While significant progress has been achieved, challenges and prospects in optimizing synthesis, improving mechanical properties, and exploring new functionalities are discussed. Overall, this review highlights the remarkable properties of inulin-based hydrogels as a promising class of biomaterials with immense potential in the biomedical, pharmaceutical, and materials science fields.

Recent Advances in Quaternary Ammonium Monomers for Dental Applications.

Resin-based dental materials have been one of the ideal choices among various materials in the treatment of dental caries. However, resin-based dental materials still have some drawbacks, such as the lack of inherent antibacterial activity. Extensive research has been conducted on the use of novel quaternary ammonium monomers (QAMs) to impart antibacterial activity to dental materials. This review provides a comprehensive overview of the recent advances in quaternary ammonium monomers (QAMs) for dental applications. The current progress and limitations of QAMs are discussed based on the evolution of their structures. The functional diversification and enhancement of QAMs are presented. QAMs have the potential to provide long-term antibacterial activity in dental resin composites, thereby prolonging their service life. However, there is a need to balance antibacterial performance with other material properties and the potential impact on the oral microbiome and general health. Finally, the necessity for further scientific progress in the development of novel quaternary ammonium monomers and the optimization of dental resin formulations is emphasized.

Recent Advances in the 3D Printing of Conductive Hydrogels for Sensor Applications: A Review.

Conductive hydrogels, known for their flexibility, biocompatibility, and conductivity, have found extensive applications in fields such as healthcare, environmental monitoring, and soft robotics. Recent advancements in 3D printing technologies have transformed the fabrication of conductive hydrogels, creating new opportunities for sensing applications. This review provides a comprehensive overview of the advancements in the fabrication and application of 3D-printed conductive hydrogel sensors. First, the basic principles and fabrication techniques of conductive hydrogels are briefly reviewed. We then explore various 3D printing methods for conductive hydrogels, discussing their respective strengths and limitations. The review also summarizes the applications of 3D-printed conductive hydrogel-based sensors. In addition, perspectives on 3D-printed conductive hydrogel sensors are highlighted. This review aims to equip researchers and engineers with insights into the current landscape of 3D-printed conductive hydrogel sensors and to inspire future innovations in this promising field.

Conductive silk fibroin hydrogel with semi-interpenetrating network with high toughness and fast self-recovery for strain sensors.

Regenerated silk fibroin (RSF) hydrogels have been extensively studied in the fields of biomedicine and wearable devices in recent years due to their outstanding biocompatibility. However, the pure RSF hydrogels usually exhibited frangibility and low ductility, limiting their application in many aspects severely. Herein, we demonstrate a tough RSF/poly (N, N-dimethylallylamine) hydrogel with semi-interpenetrating network, which possesses good mechanical properties with high stretchability (εb = 900%), tensile strength (σb = 101.7 kPa), toughness (Wf = 516.7 kJ/m3) and tearing fracture energy (T = 407.3 J/m2). Besides, the gels show low residual strain in the cyclic tests and rapid self-recovery (80% toughness recovery within 5 min with the maximum strain of 400%). Moreover, the gels also show high ionic conductivity due to the incorporation of the NaCl and the hydrogel can act as an ideal candidate for strain sensor with high sensitivity (GF = 1.84), admirable linearity, and good durability (1000 cycles with the strain of 100%). When used as a wearable strain sensor for monitoring human movements, it also can detect small and large deformations with high sensitivity. It is expected that this work can provide a new strategy for the fabrication of smart RSF-based hydrogels and expand their application in multiple scenarios.

Hydrolyzed Hydrogels with Super Stretchability, High Strength, and Fast Self-Recovery for Flexible Sensors.

Polyacrylamide is widely employed in constructing functional hydrogels. However, the volume expansion of this hydrogel in water weakens its mechanical properties and restricts its application. Herein, we report a strategy to convert the swollen and weak polyacrylamide/carboxymethyl chitosan hydrogel into a strong and tough one by hydrolysis in acid solution with an elevated temperature. The obtained hydrolyzed hydrogels possess a high strength, toughness, and tearing fracture energy of 5.9 MPa, 22 MJ/m3 and 7517 J/m2, which are 254, 535 and 186 times higher than those of the original swollen one, respectively. In addition, the gels demonstrate low residual strain and rapid self-recovery abilities. Moreover, the gels have good shape memory behavior controlled by temperature. Furthermore, the gels can be worked as strain sensors with a broad strain window, high sensitivity, excellent linear response, and great durability in monitoring human motions after immersing treatment in a normal saline solution. This work provides a new method for preparing the stretchable and tough polyacrylamide-based hydrogels used in the areas of soft actuators and flexible electronics.

A semi-interpenetrating network ionic composite hydrogel with low modulus, fast self-recoverability and high conductivity as flexible sensor.

There is a growing demand for hydrogel-based sensors due to their biomimetic structures and properties, as well as biocompatibility. However, it is still a challenge to fabricate hydrogel sensor with integration of good mechanical properties and high conductivity. Herein, a tough and conductive hydrogel is developed with semi-interpenetrating network formed by incorporating carboxymethyl chitosan and sodium chloride into polyacrylamide network. The hydrogels have high tensile strength, elongation and toughness, but low modulus comparable to human skin. In addition, the hydrogels exhibit fast self-recovery and satisfactory self-healing capabilities. Owing to the existence of sodium chloride, the hydrogel also has high conductivity, good water retention property and anti-freezing ability. When used as a strain sensor, it demonstrates a broad strain window and shows a high sensitivity in monitoring human motions. This work provides a facile method in fabricating multifunctional ionic conductive hydrogel for applications in wearable electronics and soft robotics.

A Novel Human Papillomavirus 16 L1 Pentamer-Loaded Hybrid Particles Vaccine System: Influence of Size on Immune Responses.

Cervical cancer remains the second-most prevalent female malignancy around the world, leading to a great majority of cancer-related mortality that occurs mainly in developing countries. Developing an effective and low-cost vaccine against human papillomavirus (HPV) infection, especially in medically underfunded areas, is urgent. Compared with vaccines based on HPV L1 viruslike particles (VLPs) in the market, recombinant HPV L1 pentamer expressed in Escherichia coli represents a promising and potentially cost-effective vaccine for preventing HPV infection. Hybrid particles comprising a polymer core and lipid shell have shown great potential compared to conventional aluminum salts adjuvant and is urgently needed for HPV L1 pentamer vaccines. It is well-reported that particle sizes are crucial in regulating immune responses. Nevertheless, reports on the relationship between the particulate size and the resultant immune response have been in conflict, and there is no answer to how the size of particles regulates specific immune response for HPV L1 pentamer-based candidate vaccines. Here, we fabricated HPV 16 L1 pentamer-loaded poly(d,l-lactide- co-glycolide) (PLGA)/lecithin hybrid particles with uniform sizes (0.3, 1, and 3 µm) and investigated the particle size effects on antigen release, activation of lymphocytes, dendritic cells (DCs) activation and maturation, follicular helper CD4+ T (TFH) cells differentiation, and release of pro-inflammatory cytokines and chemokines. Compared with the other particle sizes, 1 µm particles induced more powerful antibody protection and yielded more persistent antibody responses, as well as more heightened anamnestic responses upon repeat vaccination. The superior immune responses might be attributed to sustainable antigen release and robust antigen uptake and transport and then further promoted a series of cascade reactions, including enhanced DCs maturation, increased lymphocytes activation, and augmented TFH cells differentiation in draining lymph nodes (DLNs). Here, a powerful and economical platform for HPV vaccine and a comprehensive understanding of particle size effect on immune responses for HPV L1 pentamer-based candidate vaccines are provided.

Comparative studies of pharmacokinetics and anticoagulatory effect in rats after oral administration of Frankincense and its processed products.

ETHNOPHARMACOLOGICAL RELEVANCE: Frankincense (FRA), Ruxiang, is the resin of Boswellia carterii Birdw and Boswellia bhaw-dajiana Birdw which has been used for centuries as formulas to improve the circulation and to relieve pain against carbuncles. Stir-fried Frankincense (SFF) and vinegar processed Frankincense (VPF) are two major processed Frankincense, and the processing procedures reportedly enhance the curative efficacy or reduce the side effects of FRA. This paper describes the comparisons in plasma pharmacokinetic behaviors of 11-keto-ß-boswellic acid (KBA) and 3-acetyl-11-keto-ß-boswellic acid (AKBA) in FRA and its processed products, and their effects on coagulation factors and blood clotting tetrachoric, using an acute cold blood-stasis animal model after oral administration of FRA, SFF, and VPF. MATERIALS AND METHODS: For pharmacokinetic study, Sprague-Dawley (SD) rats were randomly divided into three groups, including group FRA, group SFF and group VPF. And the plasma samples were analyzed by HPLC. For study of anticoagulatory effect, SD rats were randomly divided into six groups, including control, acute cold blood-stasis model, Fu-fang-dan-shen tablet- (0.75g/kg), FRA-, SFF-, and VPF-treated (2.7g/kg) groups, respectively. The serum contents of thrombin-antithrombin complex (TAT), D-dimer (D-D), and prostacyclin (PGI2) of each group were measured by ELISA. The values of prothrombin time (PT), thrombin time (TT), activated partial thromboplastin time (APTT) and fibrinogen (FIB) were also assessed by hematology analyzer. RESULTS: Significantly increased levels of Cmax, AUC, T1/2, and MRT were found in rats treated with the processed products. In addition, decreased levels of D-D and TAT and increased contents of PGI2 were observed in rats given FRA and its processed products, compared with that of the model group. Moreover, VPF improved anticoagulation more than SFF in the animals. CONCLUSIONS: The observed improvement of anticoagulation by processed FRA may result from the increased absorption and bioavailability of triterpenoids.

Synthesis of none Bisphenol A structure dimethacrylate monomer and characterization for dental composite applications.

OBJECTIVE: In this study, new dimethacrylate monomer SiMA without Bisphenol A (BPA) structure was synthesized and used as base resin of dental composite materials with the aim of reducing human exposure to BPA derivatives. METHODS: SiMA was synthesized through ring-opening addition reaction between 1,3-bis[2(3,4-epoxycyclohex-1-yl)ethyl]tetra-methyldisiloxane and methacrylic acid, and its structure was confirmed by FT-IR and (1)H NMR spectra. SiMA was mixed with TEGDMA (50/50, wt/wt) and photoinitiation system (0.7 wt% of CQ and 0.7 wt% of DMAEMA) to form resin system. Experimental composite EC was then prepared by SiMA based resin loading with BaAlSiO2 microfillers (72wt%). Double bond conversion (DC) was determined by FT-IR analysis. Volume shrinkage (VS) was measured through variation of density before and after irradiation. Water sorption (WS) and solubility (SL) were obtained until the mass variation of polymer in distilled water kept stable. Flexural strength (FS) and modulus (FM) of the polymer were measured using a three-point bending set up. Extract of composite was used to evaluate its cytotoxic effect on humane dental pulp cells, and relative growth rate (RGR) was obtained by CCK-8 assay. Bis-GMA/TEGDMA (50/50, wt/wt) resin system and universal dental restorative materials 3M ESPE Filtek™ Z250 were used as references for neat resin system and composite material, respectively. RESULTS: FT-IR and (1)H NMR spectra showed that structure of SiMA was the same as designed. For the neat resin systems: DC of SiMA based resin was higher than that of Bis-GMA based resin (p<0.05); SiMA based resin had lower VS than Bis-GMA based resin; WS of SiMA based resin was lower than that of Bis-GMA based resin (p<0.05), while SL of SiMA based resin was nearly the same as that of Bis-GMA based resin (p>0.05); FS and FM of SiMA based resin were lower than those of Bis-GMA based resin (p<0.05). For the composite materials: DC of EC was higher than that of Z250 (p<0.05); EC and Z250 had same VS; WS of EC was lower than that of Z250 (p<0.05), and SL of EC was higher than that of Z250 (p<0.05); FS and FM of EC were lower than those of Z250 (p<0.05); RGRs of EC were lower than those of Z250 after the cells were incubated with relative extract for 24h and 48h (p<0.05), while after being incubated for 72 h, RGR of EC and Z250 had no obvious difference (p>0.05). SIGNIFICANCE: SiMA had potential to replace Bis-GMA as base resin of dental composite materials. However, formulation of SiMA based resin and composite should be optimized in terms of mechanical strength to satisfy the requirements of resin based dental materials for clinical application.