RESUMO
Sulforhodamine B (SRB) is widely utilized for cell staining and laser field. But its application is limited by aggregation-caused quenching (ACQ). In this work, we evaluated the use of UiO-66 and UiO-67 of Zr-based metal organic frameworks (Zr-MOFs) as the host to adsorb SRB molecules due to the high stabily and good loading capacity of Zr-MOFs. The fluorescence properties of the compounds were then discussed respectively. Due to the aperture difference between UiO-66 and UiO-67, they showed distinct fluorescence properties after loading SRB. When the concentration reaches 5 ppm, fluorescence quenching begins to occur in SRB@UiO-66, while it occurs in SRB@UiO-67 at 2 ppm. The solution of quenching phenomenon could open new avenues for the extensive use of SRB.
RESUMO
The binary blend materials containing the modified recycled rubber powder with maleic a hydride modified polypropylene thermoplastic elastomer were prepared by dynamic vulcanization and blended with a variety of additives such as activated agent, accelerator, solubilizer, and the crosslinking agent. The thermal properties and mechanical properties including tensile strengths and impact strengths of pristine rubber, polypropylene and their corresponding binary blends were investigated. Besides, the effects of the amount of rubber powder, polypropylene, crosslinking agent, accelerator, activator, and solvent were studied and the microstructures of the pristine rubber, pristine polypropylene, and their corresponding binary blends were observed by scanning electron microscopy. It was found that the compatibilizer could effectively disperse the size of 120 mesh of recycled rubber powder into the polypropylene in the same manner and the homogeneous tear section of the rubber/polypropylene thermoplastic elastomer was obtained. The results on the effects of additives on mechanical and morphological properties of recycled rubber/polypropylene binary blends guide the rational design of novel polymeric composites from recycled polymeric materials.
RESUMO
Isostructural zirconium-based metalâ»organic frameworks (Zr-MOFs) have attracted the attention of researchers because of their remarkable stability at high temperatures and high pressures and their chemical stabilities against acids and bases. Due to this stability, Zr-MOFs can be utilized in adsorption research, and the adsorption performance of a Zr-MOF depends on the pore size and the surroundings of the MOF. In this study, as the dimensions changed and the adsorption was carried out, the Zr-MOF material remained stable, and the adsorption of the best state was achieved at 235 mg/g. Through the simulation of theoretical kinetic models of Zr-MOFs, we initially postulated that the adsorption capacity is proportional to the pore size and that acid orange 7 (AO7) was adsorbed by the MOFs. Afterwards, we verified our hypotheses through a series of Brunauerâ»Emmettâ»Teller (BET) data analysis; non-local density function theory (NLDFT) was mainly used to analyze the data. Moreover, we determined that physical adsorption occurs on the surface of the MOFs during the adsorption process, while chemisorption occurs in the form of dye molecules combining with active sites. Ultimately, we concluded that the larger the pore size, the stronger the adsorption capacity, and this contribution casts a new light on the issue of wastewater treatment.
RESUMO
Zirconium based metal organic frameworks (Zr-MOFs) have become popular in engineering studies due to their high mechanical stability, thermostability and chemical stability. In our work, by using a theoretical kinetic adsorption isotherm, we can exert MOFs to an acid dye adsorption process, experimentally exploring the adsorption of MOFs, their external behavior and internal mechanism. The results indicate their spontaneous and endothermic nature, and the maximum adsorption capacity of this material for acid orange 7 (AO7) could be up to 358 mg·g-1 at 318 K, estimated by the Langmuir isotherm model. This is ascribed to the presence of an open active metal site that significantly intensified the adsorption, by majorly increasing the interaction strength with the adsorbates. Additionally, the enhanced π delocalization and suitable pore size of UiO-66 gave rise to the highest host-guest interaction, which further improves both the adsorption capacity and separation selectivity at low concentrations. Furthermore, the stability of UiO-66 was actually verified for the first time, through comparing the structure of the samples before and after adsorption mainly by Powder X-ray diffraction and thermal gravimetric analysis.