Per- and Poly-Fluoroalkyl Substances in Portuguese Rivers: Spatial-Temporal Monitoring.

Eighteen per-and polyfluoroalkyl substances (PFASs) were investigated in surface waters of four river basins in Portugal (Ave, Leça, Antuã, and Cértima) during the dry and wet seasons. All sampling sites showed contamination in at least one of the seasons. In the dry season, perfluorooctanoate acid (PFOA) and perfluoro-octane sulfonate (PFOS), were the most frequent PFASs, while during the wet season these were PFOA and perfluobutane-sulfonic acid (PFBS). Compounds detected at higher concentrations were PFOS (22.6 ng L-1) and perfluoro-butanoic acid (PFBA) (22.6 ng L-1) in the dry and wet seasons, respectively. Moreover, the prospective environmental risks of PFASs, detected at higher concentrations, were evaluated based on the Risk Quotient (RQ) classification, which comprises acute and chronic toxicity. The results show that the RQ values of eight out of the nine PFASs were below 0.01, indicating low risk to organisms at different trophic levels in the four rivers in both seasons, wet and dry. Nevertheless, in the specific case of perfluoro-tetradecanoic acid (PFTeA), the RQ values calculated exceeded 1 for fish (96 h) and daphnids (48 h), indicating a high risk for these organisms. Furthermore, the RQ values were higher than 0.1, indicating a medium risk for fish, daphnids and green algae (96 h).

Assessment of Micro- and Nanoplastic Composition (Polymers and Additives) in the Gastrointestinal Tracts of Ebro River Fishes.

One of the main routes of fish exposure to micro- and nanoplastics (MNPLs) is their ingestion. MNPLs can act as reservoirs of organic contaminants that are adsorbed onto their surfaces, or that can leach from their complex formulations, with potential impacts on biota and along the aquatic food chain. While MNPLs have been reported in fishes worldwide, complete information on MNPL compositions, polymers and additives continues to be scarce. In this work, the presence of MNPLs in the gastrointestinal tracts (GIT) of fish from the Ebro River (Spain) was investigated using a double suspected screening approach to assess and quantify polymers and additives. The sample-preparation procedure consisted of sequential alkaline and acidic digestions with KOH and HNO3, followed by ultrasonic-assisted extraction (USAE) with toluene. The analysis of polymers was carried out with size-exclusion chromatography followed by high-resolution mass spectrometry using an atmospheric pressure photoionization source, operating in negative and positive ionisation modes (SEC-(±)-APPI-HRMS) using full-scan acquisition (FS). Plastic additives were assessed using high-performance liquid chromatography with a C18 analytical column coupled to HRMS equipped with an electrospray ionisation source operating under positive and negative conditions (LC-(±ESI)-HRMS). The acquisition was performed in parallel with full-scan (FS) and data-dependent scan (ddMS2) modes, working under positive and negative ionisation modes. The polymers most frequently detected and quantified in fish GITs were polysiloxanes, polyethylene (PE), polypropylene (PP) and polystyrene (PS). PE was detected in 84% of the samples, with a concentration range from 0.55 to 3545 µg/g. On the other hand, plasticisers such as phthalates and stabilisers such as benzotriazoles were the most frequently identified plastic additives.

Metabolic Responses of Mytilus galloprovincialis to Fullerenes in Mesocosm Exposure Experiments.

In this study, Mediterranean mussels (Mytilus galloprovincialis) were exposed through the diet to fullerene soot at three concentrations in parallel to a control group. Their metabolomics response was assessed by high-performance liquid chromatography coupled to high-resolution mass spectrometry (HPLC-HRMS). The experiments were conducted in marine mesocosms, during 35 days (7 days of acclimatization, 21 days of exposure, and 7 days of depuration). Real conditions were emulated in terms of physicochemical conditions of the habitat. Results confirmed the bioaccumulation of fullerenes, and the metabolome of the exposed organisms revealed significant differences in the concentrations of seven free amino acids in comparison to the control group. An increase in small nonpolar amino acids (e.g., alanine) and branched chain amino acids (leucine and isoleucine) were observed. Also, glutamine concentrations decreased significantly, suggesting the activation of facultative anaerobic energy metabolism. Branched chain amino acids, such as leucine and isoleucine, followed the opposite trend after the highest level of exposure, which can imply hormesis effects. Other significant differences were observed on lipids content, such as the general increase of free fatty acids, i.e., long-chain fatty acids (lauric, myristic, and palmitic acids) when the concentration of exposure was increased. These results were consistent with hypoxia and oxidative stress.

Microalgae cultivation on wastewater digestate: ß-estradiol and 17α-ethynylestradiol degradation and transformation products identification.

Selenastrum capricornutum and Chlamydomonas reinhardtii were tested for possible biodegradation of the hormones ß-estradiol (E2) and 17α-ethinylestradiol (EE2) when cultured in anaerobic digester centrate (ADC). Neither ADC nor the hormones had a negative or toxic effect on the microalgae growth but enhanced it. E2 and EE2 biodegradation was evaluated under different culture conditions. After 7 days of treatment, between 88% and 100% of E2 was removed by S. capricornutum. Overall, 42 and 54% of the removal was attributed to biodegradation processes, while the rest of the removal was due to adsorption onto the algae biomass. For EE2, removals between 60 and 95%, depending on the culture conditions, were achieved, with biodegradation accounting for 20-54% of the removal. E2 and EE2 were completely removed in the experiments performed with C. reinhardtii, except for EE2 in the presence of ADC, which decreased to 76%. However, C. reinhardtii presented higher adsorption percentages: 86% and 71% after 7 days for E2 and EE2, respectively. Transformation products (TPs) of E2 and EE2 generated in each treatment were also monitored. Two TPs were tentatively proposed as degradation products of E2 and EE2 by the algae. In addition, the removal of 26 endocrine disruptors and related pollutants present in the centrate was also monitored: bisphenol A was completely removed, whereas tris(2-butoxyethyl)phosphate was only removed in the absence of hormones.

Assessment of perfluoroalkyl substances in food items at global scale.

This study assessed the levels of 21 perfluoroalkyl substances (PFASs) in 283 food items (38 from Brazil, 35 from Saudi Arabia, 174 from Spain and 36 from Serbia) among the most widely consumed foodstuffs in these geographical areas. These countries were chosen as representatives of the diet in South America, Western Asia, Mediterranean countries and South-Eastern Europe. The analysis of foodstuffs was carried out by turbulent flow chromatography (TFC) combined with liquid chromatography with triple quadrupole mass spectrometry (LC-QqQ-MS) using electrospray ionization (ESI) in negative mode. The analytical method was validated for the analysis of different foodstuff classes (cereals, fish, fruit, milk, ready-to-eat foods, oil and meat). The analytical parameters of the method fulfill the requirements specified in the Commission Recommendation 2010/161/EU. Recovery rates were in the range between 70% and 120%. For all the selected matrices, the method limits of detection (MLOD) and the method limits of quantification (MLOQ) were in the range of 5 to 650 pg/g and 17 to 2000 pg/g, respectively. In general trends, the concentrations of PFASs were in the pg/g or pg/mL levels. The more frequently detected compounds were perfluorooctane sulfonic acid (PFOS), perfluorooctanoic acid (PFOA) and perfluorobutanoic acid (PFBA). The prevalence of the eight-carbon chain compounds in biota indicates the high stability and bioaccumulation potential of these compounds. But, at the same time, the high frequency of the shorter chain compounds is also an indication of the use of replacement compounds in the new fluorinated materials. When comparing the compounds profile and their relative abundances in the samples from diverse origin, differences were identified. However, in absolute amounts of total PFASs no large differences were found between the studied countries. Fish and seafood were identified as the major PFASs contributors to the diet in all the countries. The total sum of PFASs in fresh fish and seafood was in the range from the MLOQ to 28ng/g ww. According to the FAO-WHO diets composition, the daily intake (DI) of PFASs was calculated for various age and gender groups in the different diets. The total PFASs food intake was estimated to be between 2300 and 3800 ng /person per day for the different diets. Finally, the risk intake (RI) was calculated for selected relevant compounds. The results have indicated that by far in no case the tolerable daily intake (TDI) (150, 1500, 50,000, 1,000,000, 150, 1500 ng/kg body weight, for perfluorohexanesulfonate (PFHxS), fluorotelomer alcohol (FTOH), perfluorobutanesulfonic acid (PFBS), perfluorobutanoic acid (PFBA), PFOS and PFOA, respectively) was exceeded.

Occurrence and fate of perfluoroalkyl and polyfluoroalkyl substances (PFAS) in an urban aquifer located at the Besòs River Delta (Spain).

Urban aquifers are at risk of contamination from persistent and mobile organic compounds (PMOCs), especially per- and polyfluoroalkyl substances (PFAS), which are artificial organic substances widely used across various industrial sectors. PFAS are considered toxic, mobile and persistent, and have therefore gained significant attention in environmental chemistry. Moreover, precursors could transform into more recalcitrant products under natural conditions. However, there is limited information about the processes which affect their behaviour in groundwater at the field-scale. In this context, the aim of this study is to assess the presence of PFAS in an urban aquifer in Barcelona, and identify processes that control their evolution along the groundwater flow. 21 groundwater and 6 river samples were collected revealing the presence of 16 PFAS products and 3 novel PFAS. Short and ultra-short chain PFAS were found to be ubiquitous, with the highest concentrations detected for perfluorobutanesulfonic acid (PFBS), trifluoroacetic acid (TFA) and trifluoromethanesulfonic acid (TFSA). Long chain PFAS and novel PFAS were found to be present in very low concentrations (<50 ng/L). It was observed that redox conditions influence the behaviour of a number of PFAS controlling their attenuation or recalcitrant behaviour. Most substances showed accumulation, possibly explained by sorption/desorption processes or transformation processes, highlighting the challenges associated with PFAS remediation. In addition, the removal processes of different intensities for three PFAS were revealed. Our results help to establish the principles of the evolution of PFAS along the groundwater flow, which are important for the development of conceptual models used to plan and adopt site specific groundwater management activities (e.g., Managed Aquifer Recharge).

BIOACCUMULATION AND DIETARY BIOACCESSIBILITY OF MICROPLASTICS COMPOSITION AND COCONTAMINANTS IN MEDITERRANEAN MUSSELS.

Microplastics (MPLs) are contaminants of emerging concern (CECs) ubiquitous in aquatic environments, which can be bioaccumulated along the food chain. In this study, the accumulation of polyethylene (PE), polystyrene (PS) and polyethylene terephthalate (PET) microplastics (MPLs) of sizes below 63 µm was assessed in Mediterranean mussels (Mytilus galloprovincialis spp). Moreover, the potential of mussels to uptake and bioaccumulate other organic contaminants, such as triclosan (TCS) and per- and polyfluoroalkyl substances (PFASs), was evaluated with and without the presence of MPLs. Then, the modulation of MPLs in the human bioaccessibility of co-contaminants was assessed by in vitro assays that simulated the human digestion process. Exposure experiments were carried out in 15 L marine microcosms. The bioaccumulation and bioaccessibility of PE, PS, PET, and co-contaminants were assessed by means of liquid chromatography -size exclusion chromatography- coupled to high-resolution mass spectrometry (LC(SEC)-HRMS). Our outcomes confirm that MPL bioaccumulation in filter-feeding organisms is a function of MPL chemical composition and particle sizes. Finally, despite the lower accumulation and bioaccumulation of PFASs in the presence of MPLs, the bioaccessibility assays revealed that PFASs bioaccessibility was favoured in the presence of MPLs. Since part of the bioaccumulated PFASs are adsorbed onto MPL surfaces by hydrophobic and electrostatic interactions, these interactions easily change with the pH during digestion, and the PFASs bioaccessibility increases.

Cytotoxicity assessment and suspected screening of PLASTIC ADDITIVES in bioplastics of single-use household items.

Bioplastics made of renewable sources provide an excellent alternative to fossil-based materials. However, similar or greater quantities of plastic additives than fossil-based plastics are used in the formulations of bioplastics to improve their performance and barrier properties. Nowadays, there is an increasing concern about sources of chemical exposure. However, there is an important knowledge gap regarding complex additive mixtures, particularly in bio-based materials. In this study, we have characterised the presence of plastic additives in single-use materials (collected from retail shops in Spain), which are made of the most common bio-based biodegradable materials, poly(lactic acid) (PLA) and poly(hydroxybutyrate) (PHB), in contrast with a fossil-based plastic material that is extensively made from high-density polyethylene (HDPE). The approach consisted of the pulverization of material in the nano-micro range (100 nm-10 µm), with the materials being extracted using different solvents and ultrasonic-assisted solvent extraction (UASE). 100% of the additives in the material cannot be extracted, but since they were performed in the same condition for all materials can inform about the fingerprint of primary organics and the relative abundances between the different materials. The extracts were analysed by high-performance liquid chromatography coupled with high-resolution mass spectrometry equipped with a heated electrospray ionisation source operated in positive and negative ionisation conditions (HPLC-HESI(+/-)-HRMS), separately, using a suspect screening approach. A total number of 203 additives were tentatively identified (confidence level 2) in the bioplastics items of this study. An average of 123 plastic additives were found in PLA items and 121 in PHB items. Plasticisers were the most abundant additives; the phthalates group was the most commonly found, while 63 plastic additives were confirmed by standards and quantified. In parallel, the cytotoxicity of plastic particles in terms of cell viability and oxidative stress was studied using A549 alveolar basal epithelial cells, and the toxicity of the different extracts was also established using HepG2 adenocarcinoma cells. The main results of this study demonstrate that the plastic particles did not show a significant reduction in cell viability, but oxidative stress was significant, with PLA being the material that showed the highest effect. On the other hand, extracts of plastic particles did not show inhibition of cell viability except for HDPE extract, but the different extracts produced oxidative stress, with PLA showing the highest effect. Although the item showing the highest concentrations of additives was the extract of PLA material while also showing the most elevated oxidative stress, the low migration of toxicants from plastic materials ensures their safe use. However, this also supports the idea that bioplastics can contain many toxic substances in their formulations, some of which are unknown and should be studied in more depth.

Exposure to micro(nano)plastics polymers in water stored in single-use plastic bottles.

Human exposure to micro (nano)plastics (MNPLs) has become a significant concern as a potential health threat. Exposure routes include ingestion, inhalation, and dermal contact, being food and drinking water the primary sources of oral exposure. Here we present the quantification of polymers of MNPLs particles from 700 nm to 20 µm in bottled water commercialised in Spain, including an estimation of the potential risk for daily consumers. We evaluated samples from 20 popular brands in 0.5 and 1.5 L plastic bottles. A double-suspect screening approach developed and validated in our research group for drinking water was adapted for bottled water samples. The identification and quantification of MNPLs-polymers in mass units and the tentative identification of plastic additives (PA) until the second level of confidence was carried out based on high-performance liquid chromatography coupled to high-resolution mass spectrometry (HPLC-HRMS). The results showed the presence of polypropylene (PP), polyethylene (PE) and polypropylene terephthalate (PET) in the samples. Among them, PE was the most frequently detected and quantified polymer (55% of samples) followed by PET which was detected in 33% of the samples and showing the highest concentration (4700 ng L-1). The median value of the sum of polymer concentrations was 359 ng L-1. In addition, 28 plastic additives were detected, where at least one of them was present in 100% of the samples. Stabilizers and plasticisers were the most frequently identified. A prioritisation study was performed using a multi-QSAR modelling software, where bis(2-ethylhexyl) adipate and bis(2-ethylhexyl) phthalate were estimated as the most potentially harmful compounds for human health. Overall, findings suggest that bottled water is a non-negligible route to exposure to MNPLs.

Micro(nano)plastics in the atmosphere of the Atlantic Ocean.

The occurrence, long-range atmospheric transport and deposition of micro and nano plastics (MNPLs) remains un-quantified for the oceanic atmosphereopen ocean. Here we show the characterisation of MNPLs and the aerosol composition (PM10) in a north-south Atlantic transect from Vigo (Spain) to Punta Arenas (Chile). The analytical procedure to assess the composition of MNPLs consisted of a double suspect screening approach of the polymers and additives, the two constituents of plastics. Polymers were analysed by size exclusion chromatography coupled with high-resolution mass spectrometry using an atmospheric pressure photoionization source operated in positive and negative conditions (HPLC(SEC)-APPI(+/-)-HRMS). Plastic additives were screened with high-performance liquid chromatography coupled to high-resolution mass spectrometry using an electrospray ionisation source (HPLC-ESI(+/-)-HRMS). The most common polymers were polyethylene (PE), polypropylene (PP), polyisoprene (PI), and polystyrene (PS), with the highest polymer concentration being 51.7 ng·m-3 of PI. The air mass back trajectories showed the variable influence of oceanic and terrestrial air masses. These differences were reflected in the aerosol composition with different contributions of Saharan dust, sea spray aerosol, organic/elemental carbon, and MNPLs. Results showed that samples largely influenced by sea-spray and air masses originating from coastal South America and the north Atlantic subtropical gyre were more contaminated by MNPLs. Moreover, this information was complemented by the characterisation of the largest particles using scanning electron microscopy (SEM) and µ-Fourier Transform Infrared Spectroscopy (µ-FTIR). This work provides the first field evidence of the long-range transport of MNPLs in most of the Atlantic Ocean, as the result of dynamic coupling between the lower atmosphere and the surface ocean. Sea-spray formation arises as a key driver for the aerosolisation of MNPLs, and atmospheric transport followed by dry deposition may modulate the occurrence of MNPLs in large oceanic regions, issues that will require future research efforts.

First Report of the Joint Exposure to Glyphosate and Glufosinate of a Male Population in the Province of Córdoba (Argentina).

Despite potential health implications, data on the presence of Glyphosate (GLY) and other non-GLY herbicides in human matrices remain scarce. This study aimed to develop a simple and cost-effective methodology for detecting and quantifying GLY, its primary biodegradation product; aminomethylphosphonic acid (AMPA); and glufosinate (GLU) in plasma and urine of environmentally and occupationally exposed populations from the province of Córdoba (Argentina). Different alternatives of pre-treatment, derivatization with FMOC-Cl, solid phase extraction, and final sample conditioning steps were evaluated to improve the quantification of the herbicides by a high-performance liquid chromatography system coupled to a triple-quadrupole mass spectrometer. Recoveries ranged from 39 to 84% in both matrices, while limits of quantification were 3, 1, and 0.3 ng/mL and 3.6, 5.1, and 0.3 ng/mL for AMPA, GLY, and GLU in plasma and urine, respectively. In plasma samples, GLY was the most frequently detected analyte (32%), followed by GLU (10%). In urine samples, GLU was the most frequently detected herbicide (13%), followed by GLY (6%). No differences between group or matrix correlations were found. This study is the first report of GLU in human biological matrices and should be used to establish baseline values for future surveillance systems.

Automated analysis of perfluorinated compounds in human hair and urine samples by turbulent flow chromatography coupled to tandem mass spectrometry.

Perfluorinated compounds (PFCs) are ubiquitous contaminants of humans and animals worldwide. PFCs are bioaccumulated because of their affinity for proteins. It has been shown they could have a variety of toxicological effects and cause damage to human health, emphasizing the need for sensitive and robust analytical methods to assess their bioaccumulation in humans. In this paper we report the development and validation of an analytical method for analysis of PFCs in the non-invasive human matrices hair and urine. The method is based on rapid and simple sample pre-treatment followed by online turbulent flow liquid chromatography and tandem mass spectrometry (TFC-LC-MS-MS) for analysis of 21 PFCs. The method was validated for both matrices. Percentage recovery was between 60 and 105 for most compounds in both matrices. Limits of quantification ranged from 0.1 to 9 ng mL(-1) in urine and from 0.04 to 13.4 in hair. The good performance of the method was proved by investigating the presence of selected PFCs in 24 hair and 30 urine samples from different donors living in Barcelona (NE Spain). The results were indicative of bioaccumulation of these compounds in both types of sample. PFOS and PFOA were most frequently detected in hair and PFBA in urine.

Analysis of UV filters in tap water and other clean waters in Spain.

The present paper describes the development of a method for the simultaneous determination of five hormonally active UV filters namely benzophenone-3 (BP3), 3-(4-methylbenzylidene) camphor (4MBC), 2-ethylhexyl 4-(dimethylamino) benzoate (OD-PABA), 2-ethylhexyl 4-methoxycinnamate (EHMC) and octocrylene (OC) by means of solid-phase extraction and gas chromatography-electron impact ionization-mass spectrometry. Under optimized conditions, this methodology achieved low method limits of detection (needed for clean waters, especially drinking water analysis), between 0.02 and 8.42 ng/L, and quantitative recovery rates higher than 73% in all cases. Inter- and intraday precision for all compounds were lower than 7% and 11%, respectively. The optimized methodology was applied to perform the first survey of UV absorbing compounds in tap water from the metropolitan area and the city of Barcelona (Catalonia, Spain). In addition, other types of clean water matrices (mineral bottled water, well water and tap water treated with an ion-exchange resin) were investigated as well. Results evidenced that all the UV filters investigated were detected in the water samples analyzed. The compounds most frequently found were EHMC and OC. Maximum concentrations reached in tap water were 290 (BP3), 35 (4MBC), 110 (OD-PABA), 260 (EHMC), and 170 ng/L (OC). This study constitutes the first evidence of the presence of UV filter residues in tap water in Europe.

Determination of glyphosate in groundwater samples using an ultrasensitive immunoassay and confirmation by on-line solid-phase extraction followed by liquid chromatography coupled to tandem mass spectrometry.

Despite having been the focus of much attention from the scientific community during recent years, glyphosate is still a challenging compound from an analytical point of view because of its physicochemical properties: relatively low molecular weight, high polarity, high water solubility, low organic solvent solubility, amphoteric behaviour and ease to form metal complexes. Large efforts have been directed towards developing suitable, sensitive and robust methods for the routine analysis of this widely used herbicide. In the present work, a magnetic particle immunoassay (IA) has been evaluated for fast, reliable and accurate part-per-trillion monitoring of glyphosate in water matrixes, in combination with a new analytical method based on solid-phase extraction (SPE), followed by liquid chromatography (LC) coupled to tandem mass spectrometry (MS/MS), for the confirmatory analysis of positive samples. The magnetic particle IA has been applied to the analysis of about 140 samples of groundwater from Catalonia (NE Spain) collected during four sampling campaigns. Glyphosate was present above limit of quantification levels in 41% of the samples with concentrations as high as 2.5 µg/L and a mean concentration of 200 ng/L. Good agreement was obtained when comparing the results from IA and on-line SPE-LC-MS/MS analyses. In addition, no false negatives were obtained by the use of the rapid IA. This is one of the few works related to the analysis of glyphosate in real groundwater samples and the presented data confirm that, although it has low mobility in soils, glyphosate is capable of reaching groundwater.

Polymers of micro(nano) plastic in household tap water of the Barcelona Metropolitan Area.

Microplastics (MPLs) are emerging persistent pollutants affecting drinking water systems, and different studies have reported their presence in tap water. However, most of the work has a focus on particles in the 100-5 µm range. Here, a workflow to identify and quantify polymers of micro and nanoplastics (MNPLs), with sizes from 0.7 to 20 µm in tap water, is presented. The analytical method consisted of water fractionated filtration followed by toluene ultrasonic-assisted extraction and size-exclusion chromatography, using an advanced polymer chromatography column coupled to high-resolution mass spectrometry with atmospheric pressure photoionization source with negative and positive ionization conditions (HPLC(APC)-APPI(±)-HRMS) and normal phase chromatography HILIC LUNA® column and electrospray ionisation source in positive and negative mode (HPLC(HILIC)-ESI(±)-HRMS). The acquisition was performed in full scan mode, and the subsequent tentative identification of MNPLs polymers has been based on increasing the confirmation level, including the characterisation of monomers by using Kendrick Mass Defect (KMD) analysis, and confirmation and quantification using standards. This approach was applied to assess MNPLs in tap water samples of the Barcelona Metropolitan Area (BMA), that were collected from August to October 2020 from home taps of volunteers distributed in the 42 postal codes of the BMA. Polyethylene (PE), polypropylene (PP), polyisoprene (PI), polybutadiene (PBD), polystyrene (PS), polyamide (PA), and polydimethylsiloxanes (PDMS) were identified. PE, PP, and PA were the most highly detected polymers, and PI and PBD were found at the highest concentrations (9,143 and 1,897 ng/L, respectively). A principal component analysis (PCA) was conducted to assess differences in MNPLs occurrence in drinking water, that was provided from the two drinking water treatment plants (DWTPs) suppliers. Results showed that no significant differences (at 95% confidence level) were established between the drinking water supplies to the different areas of the BMA.

Perfluorinated compounds in food: a global perspective.

Perfluorinated compounds (PFCs) are resistant to breakdown and are turning up in unexpected places around the world, becoming emerging food contaminants. Although these chemicals have been used in countless products since the 1950s, they have been subject to little control until now. There is still an insufficient knowledge of their sources, occurrence, and hazards for food safety decision making. This article provides a comprehensive review of the food contamination levels and dietary intake risks posed by PFCs, as well as the specific methods developed for their determination. It is based on the evaluation of the published literature between 2004 and the beginning of 2010, with special emphasis on those reports of the last two years and in the examination of the growing body of studies on the exposure assessment and food occurrence of PFCs. The current state-of-the art and future perspectives in extraction, clean-up, detection, identification, confirmation, and quantification highlighting the advantages and limitations of each technique have been summarized. How much is known about the sources and pathways of food web and human exposure, which is needed to control and manage the release of these emerging toxic contaminants, has also been explained.

Current Insights into Potential Effects of Micro-Nanoplastics on Human Health by in-vitro Tests.

Humans are exposed to micro and nanoplastics (MNPLs) through inhalation, ingestion and, to a lesser extent, dermal contact. In recent years, new insights indicate the potential of MNPLs to cause damages to human health. Particle toxicity can include oxidative stress, inflammatory lesions, and then increased internalization or translocation through tissues. On the other hand, plastic additives are used in plastic particles, once internalized, can release toxic substances. It is noteworthy that the potential effects of MNPLs encompass a wide range of polymers and chemical additives, showing various physicochemical and toxicological properties, and the size, shape and surface properties are other variables influencing their effects. In spite of the research carried out recently, MNPLs research is in its early stages, and further investigation is required. In this review article, the knowledge of human exposure routes and the recent results on the toxicological effects of MNPLs in human health are presented and discussed. Finally, the current limitations and the main gaps in the body of knowledge are summarised.

Screening of suspected micro(nano)plastics in the Ebro Delta (Mediterranean Sea).

This is the first work reporting the use of a double suspect-screening to assess most common polymers and additives in micro(nano)plastics (NPLs/MPLs) found in environmental waters. The method consisted of water filtration followed by ultrasonic-assisted extraction with toluene and analysis employing size exclusion chromatography using an advanced polymer chromatography column coupled to high-resolution mass spectrometry with an atmospheric pressure photoionisation source by negative ionisation conditions (LC(APC)-APPI(-)-HRMS). The identification of NPL/MPLs polymers has been based on increasing confirmation level, including the monomers characterisation by the Kendrick Mass Defect and confirmation and quantification when standards were available. In parallel, the identification of main additives in NPL/MPLs composition, as well organic contaminants adsorbed onto the plastic particles were carried out by analysis of the extracts by LC(C18)-APPI (+/-)-HRMS. To assess the impact of plastic pollution it is necessary to assess the composition in terms of polymers but also the additives. This screening approach has been employed to study composition of NPL/MPLs in the Ebro Delta. Two sampling campaigns including freshwater and seawater samples have been investigated to assess plastic composition in the top 5 cm. Polystyrene (PS), polyethylene (PE), polyisoprene (PI), polybutadiene (PBD), polypropylene (PP) and polysiloxanes were the most detected polymers and PP and PE, sizing between < 1000 and 2000 Da, were found at concentrations reaching up to 7000 ng/L in some areas. The pentadecanoic acid, 1,2,3-benzotriazoles, 2-ethylhexanoic acid (2-EHA), and phthalates such as dimethyl phthalate, mono(2-ethylhexyl) phthalate (MEHP) and the phthalimide were more frequently detected plastic additives. Finally, series of organic contaminants were as well detected in the particulate fraction. These organic contaminants cannot be associated to plastic compositions but can be associated to their adsorption to the particulate matter, in particular to NPL/MPLs, due to their non-polar character. Among these organic contaminants, the more frequently detected were pharmaceutical compounds, food additives and pesticides.

Combining an effect-based methodology with chemical analysis for antibiotics determination in wastewater and receiving freshwater and marine environment.

Two different methodologies were combined to evaluate the risks that antibiotics can pose in the environment; i) an effect-based methodology based on microbial growth inhibition and ii) an analytical method based on liquid-chromatography coupled to mass spectrometry (LC-MS). The first approach was adapted and validated for the screening of four antibiotic families, specifically macrolides/ß-lactams, quinolones, sulfonamides and tetracyclines. The LC-MS method was applied for the identification and quantification of target antibiotics; then, the obtained results were combined with ecotoxicological data from literature to determine the environmental risk. The two methodologies were used for the analysis of antibiotics in water samples (wastewater, river water and seawater) and biofluids (fish plasma and mollusk hemolymph) in two monitoring campaigns undertaken in the Ebro Delta and Mar Menor Lagoon (both in the Mediterranean coast of Spain). Both approaches highlighted macrolides (azithromycin) and quinolones (ciprofloxacin and ofloxacin) as the main antibiotics in wastewater treatment plant (WWTP) effluents with potential risk for the environment. However, no risk for the aquatic life was identified in the river, lagoon and seawater as antibiotic levels were much lower than those in WWTP effluents. Fish from Ebro River were the organisms presenting the highest antibiotic concentration when compared with bivalves (mussels) from the Mediterranean Sea and gastropods (marine snails) from the Mar Menor Lagoon. The effect-based methodology successfully determined antibiotic risk in wastewater, but its applicability was less clear in environmental waters such as seawater, due to its high detection limits. Improving sample preconcentration could increase the method sensibility. Overall, combination of both methodologies provides comprehensive insights in antibiotic occurrence and risk associated in areas under study.

Priority and emerging organic microcontaminants in three Mediterranean river basins: Occurrence, spatial distribution, and identification of river basin specific pollutants.

There is a worldwide growing use of chemicals by our developed, industrialized, and technological society. More than 100,000 chemical substances are thus commonly used both by industry and households. Depending on the amount produced, physical-chemical properties, and mode of use, many of them may reach the environment and, notably, the aquatic receiving systems. This may result in undesirable and harmful side-effects on both the human and the ecosystem's health. Mediterranean rivers are largely different from Northern and Central European rivers in terms of hydrological regime, climate conditions (e.g. air temperature, solar irradiation, precipitation), and socio-economics (e.g. land use, tourism, crop types, etc.), with all these factors leading to differences in the relative importance of the environmental stressors, in the classes and levels of the pollutants found and their environmental fate. Furthermore, water scarcity might be critical in affecting water pollution because of the lowered dilution capacity of chemicals. This work provides raw chemical data from different families of microcontaminants identified in three selected Mediterranean rivers (the Sava, Evrotas, and Adige) collected during two sampling campaigns conducted in 2014 and 2015 in three different matrices, namely, water, sediments, and biota (fish). More than 200 organic micropollutants were analyzed, including relevant groups like pharmaceuticals, personal care products, perfluorinated compounds, pesticides, pyrethroid insecticides, flame retardants, and persistent organic pollutants. Data obtained were summarized with some basic statistics for all compound families and matrices analyzed. Observed occurrence and spatial patterns were interpreted both in terms of compound physical-chemical properties and local environmental pressures. Finally, their spatial distribution was examined and their ecotoxicological risk in the water phase was assessed. This allowed locating, at each basin, the most polluted sites ("hot spots") and identifying the respective river basin specific pollutants (RBSPs), prioritizing them in terms of the potential ecotoxicological risk posed to the aquatic ecosystems.