Preparation and Performance Verification of a Solid Slow-Release Carbon Source Material for Deep Nitrogen Removal in Urban Tailwater.

Urban tailwater typically has a low carbon-to-nitrogen ratio and adding external carbon sources can effectively improve the denitrification performance of wastewater. However, it is difficult to determine the dosage of additional carbon sources, leading to insufficient or excessive addition. Therefore, it is necessary to prepare solid slow-release carbon source (SRC) materials to solve the difficulty in determining the dosage of carbon sources. This study selected two SRCs of slow-release carbon source 1 (SRC1) and slow-release carbon source 2 (SRC2), with good slow-release performance after static carbon release and batch experiments. The composition of SRC1 was: hydroxypropyl methylcellulose/disodium fumarate/polyhydroxy alkanoate (HPMC/DF/PHA) at a ratio of 3:2:4, with an Fe3O4 mass fraction of 3%. The composition of SRC2 was: HPMC/DF/PHA with a ratio of 1:1:1 and an Fe3O4 mass fraction of 3%. The fitted equations of carbon release curves of SRC1 and SRC2 were y = 61.91 + 7190.24e-0.37t and y = 47.92 + 8770.42e-0.43t, respectively. The surfaces of SRC1 and SRC2 had a loose and porous morphological structure, which could increase the specific surface area of materials and be more conducive to the adhesion and metabolism of microorganisms. The experimental nitrogen removal by denitrification with SRCs showed that when the initial total nitrogen concentration was 40.00 mg/L, the nitrate nitrogen (NO3--N) concentrations of the SRC1 and SRC2 groups on the 10th day were 2.57 and 2.66 mg/L, respectively. On the 20th day, the NO3--N concentrations of the SRC1 and SRC2 groups were 1.67 and 2.16 mg/L, respectively, corresponding to removal efficiencies of 95.83% and 94.60%, respectively. The experimental results indicated that SRCs had a good nitrogen removal effect. Developing these kinds of materials can provide a feasible way to overcome the difficulty in determining the dosage of carbon sources in the process of heterotrophic denitrification.

Exploration on anti-hypoxia properties of peptides: a review.

Peptides are important components of human nutrition and health, and considered as safe, nontoxic, and easily absorbed potential drugs. Anti-hypoxia peptides are a kind of peptides that can prevent hypoxia or hypoxia damage. In this paper, the sources, preparations, and molecular mechanisms of anti-hypoxia peptides were systemically reviewed. The combination of bioinformatics, chemical synthesis, enzymatic hydrolysis, and microbial fermentation are recommended for efficient productions of anti-hypoxic peptides. The mechanisms of anti-hypoxic peptides include interference with glycolytic process and HIF-1α pathway, mitochondrial apoptosis, and inflammatory response. In addition, bioinformatics analysis, including virtual screening and molecular docking, provides an alternative or auxiliary method for exploring the potential anti-hypoxic activities and mechanisms of peptides. The potential challenges and prospects of anti-hypoxic peptides are also discussed. This paper can provide references for researchers in this field and promote further research and clinical applications of anti-hypoxic peptides in the future.

Molecular identification and functional analysis of X-linked inhibitor of apoptosis -associated factor-1 (XAF1) in grass carp, Ctenopharyngodon idella.

X-linked inhibitor of apoptosis protein (XIAP) -associated factor 1 (XAF1) is an interferon-stimulated gene which exhibits pro-apoptosis effect. In this study, XAF1 was characterized from grass carp Ctenopharyngodon idella and its expression pattern and function were analyzed. The open reading frame (orf) of XAF1 is 789 nucleotides (nt) encoding 262 amino acids. SMART online search results showed that a C2H2-type and six C2HC-type zinc-fingers were found in XAF1, however, the XAF1 of grass carp showed high sequence identity to zebrafish (71%), low sequence identity to tetrapods (21-22%). Rt-qPCR results showed that XAF1 was constitutively expressed in all tested organs/tissues with highest expression in blood. An inductive expression of XAF1 at mRNA level was observed in peripheral blood leucocytes (PBLs) and C. idellus kidney cells (CIKs) after treatment with C. idellus recombinant interferon-γ (rIFNg). Overexpressing XAF1 in CIKs exhibited resistance against grass carp reovirus (GCRV) and more sensitivity to cisplatin. These results implied a functional homologue of XAF1 in evolution, however the mechanism may require further investigation.

Focal adhesion signaling pathway involved in skin immune response of tongue sole Cynoglossus semilaevis to Vibrio vulnificus infection.

Focal adhesion (FA) plays a key role in cell adhesion, migration and antibacterial immune, but it remained unclear in fish. In this study, half-smooth tongue sole Cynoglossus semilaevis were infected with Vibrio vulnificus, and then immune-related protein in the skin, especially for FA signaling pathway were screened and identified by iTRAQ analysis. Results showed that the differentially expressed proteins (DEPs) in skin immune response (eg., ITGA6, FN, COCH, AMBP, COL6A1, COL6A3, COL6A6, LAMB1, LAMC1, FLMNA) were firstly found in FA signaling pathway. Furthermore, the validation analysis of FA-related genes were basically consistent with the iTRAQ data at 36 hpi (r = 0.678, p < 0.01), and their spatio-temporal expressions were confirmed by qPCR analysis. The molecular characterization of vinculin of C. semilaevis was described. This study will provide a new perspective for understanding the molecular mechanism of FA signaling pathway in the skin immune response in marine fish.

Comprehensive improvements in the emergency laboratory test process based on information technology.

OBJECTIVE: To explore the application effects of information technology (IT) on emergency laboratory testing procedures. METHODS: In this study, IT-based optimisation of the emergency laboratory testing process was implemented between October and December 2021. Thus, the emergency laboratory test reports from January to September 2021 were placed into the pre-optimised group, while those from January to September 2022 were categorised into the post-optimised group. Besides, the emergency laboratory test report time, emergency laboratory test report time limit coincidence rate, error rate, and employee and patient satisfaction levels in individual months and across the whole period were described. Moreover, changes in the above indicators before and after the implementation of IT-based optimisation were explored and the application effects of IT-based optimisation were also evaluated. RESULTS: The emergency laboratory test report times after the implementation of IT-based optimisation were shorter than those before IT-based optimisation (P < 0.05). The total number of laboratory test items before and after information optimization amounted to 222,139 and 259,651, respectively. Also, IT-based optimisation led to an increase in the emergency laboratory test report time limit coincidence rate from 98.77% to 99.03% (P < 0.05), while the emergency laboratory test report error rate fell from 0.77‱ to 0.15‱ (P < 0.05). Additionally, IT-based optimisation resulted in increases in both employee satisfaction, from 80.65% to 93.55% (N = 31, P > 0.05), and patient satisfaction, from 93.06% to 98.44% (P < 0.05). CONCLUSION: The automation and IT-based optimisation of the emergency laboratory testing process significantly reduces the emergency laboratory test report time and error rate. Additionally, IT-driven optimization enhances the alignment of emergency laboratory test report deadlines and enhances the overall quality and safety of emergency laboratory testing.

Crosstalk suppression for high-density traveling-wave MZM array based on static and dynamic combined analysis and circuit-level designs.

Electrical crosstalk severely degrades the performance of Mach-Zehnder modulator (MZM) array. However, conventional crosstalk suppression techniques incur losses of large amounts of chip area for signal isolation, which becomes a bottleneck of high-density electronic-photonic integrated circuit. In this paper, the electrical crosstalk of Traveling-Wave MZM array is originally analyzed with static and dynamic combined crosstalk coefficients. Circuit-level suppression techniques of differential dual-drive electrode schemes with tightly coupled electrode pairs and a virtual ground structure with full-matching termination circuit are investigated for noise-removing effects. Simulation results show that the dynamic electrical crosstalk coefficient between two adjacent modulators is reduced to below 1.5%, which is five times lower than the baseline. The electro-optical link measurements show that the BER is significantly reduced from 1E-3 to 1E-12 for multi-channel operation, which confirms the effectiveness of the crosstalk suppression techniques.

Prolonged low-salt immersion effectively controls Flavobacterium columnare infection in Murray cod Maccullochella peelii peelii.

A disease outbreak occurred in Murray cod Maccullochella peelii peelii in a recirculating aquaculture farm in Tianjin city, China, in 2019. Strain MRX-2019 was isolated and considered to be the etiological pathogen; it was identified as Flavobacterium columnare based on a 16S rDNA gene sequence analysis and physiological and biochemical tests. The effect of salinity on the growth of MRX-2019 was investigated in vitro. Salinity >4‰ (i.e. 6‰) inhibited MRX-2019 growth, whereas 8 and 10‰ salinity killed it. The effect of 4‰ salinity on F. columnare was not significant (p > 0.05). When MRX-2019-infected Murray cod were treated with 4, 6, or 8‰ salinity, the mortality rate was reduced by 8.9, 67.76, or 75.56%, respectively, compared with that of the control. However, the mortality rate increased by 7.77% at 10‰ salinity. In this study, we found that maintaining the fish in freshwater with 6-8‰ salinity effectively reduced the mortality of these fish when infected with F. columnare. The findings provide an environmentally friendly control strategy for columnaris disease in Murray cod.

Development of a TaqMan real-time quantitative PCR assay to detect Metschnikowia bicuspidata in Chinese mitten crab Eriocheir sinensis.

Milky disease of Chinese mitten crab Eriocheir sinensis caused by Metschnikowia bicuspidata is a novel disease with high mortality. No effective treatment is currently available, but a rapid, accurate detection method is required for the prevention and control of the disease. In this study, the genome-sequencing results of M. bicuspidata and similar species were used for comparative genomic analysis for genes specific to M. bicuspidata. A quantitative PCR (qPCR) detection method for M. bicuspidata was then established using the specific primers and probes designed according to the sequence of a hypothetical protein gene specific to M. bicuspidata. The assay was found to have a high degree of repeatability and reproducibility, with a linear dynamic range (R2 = 0.998) extending over 9 log10 dilutions and a high efficiency (100.7%). Furthermore, the method showed high sensitivity, being able to detect at least 11.3 copies µl-1 of recombinant plasmid, and strong specificity, without any cross-reaction with any of the 9 species of yeast that are closely related to M. bicuspidata or any of 16 species of pathogenic bacteria commonly observed in aquatic animals. The established method was used to examine 138 apparently healthy crabs collected from 22 farms, with 21 samples (15.2%) found to be M. bicuspidata-positive. Thus, the developed qPCR assay is a specific, sensitive, stable, and rapid diagnostic method for the detection and quantification of M. bicuspidata DNA from E. sinensis tissues.

Using information technology to optimize the identification process for outpatients having blood drawn and improve patient satisfaction.

BACKGROUND: This study explored the application effect of information technology in optimizing the patient identification process. METHODS: The method for optimizing the identification process involved in drawing blood among outpatients using information technology was executed from July 2020. In this paper, 959 patients who had blood drawn from January to June 2020 were included as the pre-optimization group, and 1011 patients who had blood drawn from July to December 2019 were included as the post-optimization group. The correct rate of patient identification, waiting time, and patient satisfaction before and after the optimization were statistically analyzed. The changes in these three indexes before and after the optimization implementation, as well as the application effects, were compared. RESULTS: The correct rate of patient identification after optimization (99.80%) was higher than before optimization (98.02%) (X2 = 13.120; P < 0.001), and the waiting time for having blood drawn was also significantly shortened (t = 8.046; P < 0.001). The satisfaction of patients was also significantly improved (X2 = 20.973; P < 0.001). CONCLUSIONS: By combining information technology with the characteristics of blood collection in our hospital, using the call system to obtain patient information, then scan the QR code of the guide sheet for automatic verification, and finally manually reconfirm patient information, which can significantly reduce the occurrence of identification errors, improve work efficiency and improve patients' satisfaction.

Hierarchical, Highly Open Microtubes and Columnar Liquid Crystals Self-Assembled from Symmetrical and Asymmetrical Colloidal Rings.

The use of simple building blocks to produce hierarchical and porous structured materials is highly desired. Rings are simple colloidal particles but unique for their internal cavities. Here we report the self-assembly (SA) of colloidal rings with tunable asymmetry mediated by a depletion force and demonstrate that a variety of porous colloidal superstructures from microtubes, flexible chains, (plastic) crystals to highly open liquid crystals (LCs) can be formed along the predesigned SA paths. In particular, the SA is staged in binary or ternary systems. Large rings first form complex ring-in-ring and ring-in-ring-in-ring assemblies by capturing smaller rings, which, as new building blocks, can further form multi-walled microtubes and open columnar LCs. Moreover, a plastic columnar LC with alternating intracolumnar stacking is found from asymmetrical rings. The SA with colloidal rings opens a new avenue to construct hierarchical and porous ordered metamaterials.

Diastereo- and Enantioselective Silver-Catalyzed [3+3] Cycloaddition and Kinetic Resolution of Azomethine Imines with Activated Isocyanides.

In contrast to the well-established [3+2] cycloaddition reactions, the catalytic enantioselective [3+n] (n≥3) cycloaddition reaction of activated isocyanides for the preparation of six-membered or larger ring systems has remained underdeveloped. Herein, we report the first example of highly diastereo- and enantioselective [3+3] cycloaddition of activated isocyanides with azomethine imines. By employing silver catalysis, a wide range of biologically important bicyclic 1,2,4-triazines were obtained in high yields (up to 99 %) with good to excellent stereoselectivities (up to >20 : 1 dr, 99 % ee). In addition, the same catalytic system could be applied to both the late-stage functionalization of complex bioactive molecules and the kinetic resolution of racemic azomethine imines, further highlighting its versatility and synthetic utility.

Torsional Strain-Independent Catalytic Enantioselective Synthesis of Biaryl Atropisomers.

Catalytic asymmetric dynamic kinetic resolution of configurationally labile bridged biaryls is emerging as a powerful strategy for atropisomer synthesis. However, the reported examples suffer from an inherent challenge as the reactivity is highly dependent on the torsional strain of the biaryl substrates, which significantly narrows down the scope and hampers the application. Herein, we report our discovery and development of a torsional strain-independent reaction between biaryl thionolactones and activated isocyanides. By employing auto-tandem silver catalysis, a universal synthesis of both tri- and tetra-ortho-substituted thiazole-containing biaryls was realized in high yields with high enantioselectivities. In addition, these products could be facilely converted to a novel type of bridged biaryls bearing an eight-membered lactone. Mechanistic studies were carried out to elucidate the cause of this unusual torsional strain-independent reactivity.

Frame-Guided Synthesis of Polymeric Colloidal Discs.

Anisotropic colloidal particles are important building blocks for the studies of self-assembly, which are visualized models for basic research and can be used to construct structured materials. Discs are one of the most typical anisotropic colloids; however, the synthesis of monodisperse colloidal discs with well-defined shape remains a challenge. Here we report a novel strategy for synthesizing polymeric discs based on frame-guided droplet shrinkage. This was realized by creating frame/liquid core/shell rings and utilizing the shrinking instability of the liquid rings. The resulting disc's shape parameters are tunable. The method is general, is not limited to specific polymers, solvents, and frames, and therefore has the potential to afford a variety of polymer discs. We also demonstrate the possibility of tuning the surface chemistry of the discs through surface-initiated polymerization. The frame-guided droplet shrinkage method opens up a new way to design and fabricate colloidal particles.

First report of a disease caused by Bacillus cereus in cultured loach Paramisgurnus dabryanus.

Bacillus cereus is commonly considered a bacterium pathogenic to mammals, but several studies have suggested that it also induces diseases in fish. In 2017 and 2018, 2 strains of B. cereus, NQ-2017-17 and NQ-2018-8, were isolated from diseased large-scale loach Paramisgurnus dabryanus in Tianjin, China, and were considered to be the pathogens responsible for the disease. These stains were identified as B. cereus based on the results of 16S rDNA gene sequence analysis, Vitek biochemical tests, physiological and biochemical tests, and B. cereus group species-specific PCR. Strains NQ-2017-7 and NQ-2018-8 were found to contain virulence genes (e.g. hblA, hblC, hblD, entFM, and bceT) causing pathological damage to the spleen, kidneys, liver, and gills of loach. The median lethal dose (LD50) of NQ-2017-7 and NQ-2018-8 for loach were 1.0 ×106.64 and 1.0 ×106.49 CFU ml-1, respectively. To our knowledge, this is the first report of loach disease caused by a member of the genus Bacillus.

Systematic evaluation of the physicochemical properties and the volatile flavors of yak meat during chilled and controlled freezing-point storage.

In this study, the physicochemical properties (total volatile basic nitrogen (TVB-N), pH, and peroxide value) and the volatile flavors of yak meat were systematically evaluated during chilled (0 °C) and controlled freezing-point (- 2 °C) storage. The TVB-N reached 15.21 mg/100 g after 18 days of storage at 0 °C, which exceeded the secondary freshness value according to the Chinese national standard. For storage at - 2 °C, the TVB-N did not exceed 15 mg/100 g until 24 days. Compared with storage at 0 °C, the samples stored at - 2 °C had a slower rate of increase in TVB-N, pH, and peroxide values. The changes in volatile compounds in yak meat during storage at - 2 °C and 0 °C for 24 days were investigated using headspace solid-phase microextraction (HS-SPME) followed by gas chromatography-mass spectrometry (GC-MS). The correlations between the changes in the volatile compound contents and meat quality deterioration revealed significant negative correlations (r min = 0.902, p < 0.05) between some aldehyde flavor components (nonanal, heptanal, benzaldehyde, decanal, and myristal) and TVB-N in the samples stored at controlled freezing-point and chilled temperatures. The decreases in nonanal, benzaldehyde, and myristal contents in yak meat followed zero order reaction kinetics. This result indicated, because of the highly selective and sensitive colorimetric detection method, that volatile compounds can effectively predict the decay in quality of yak meat stored at low temperature in advance. Thus, based on physicochemical and volatile flavor analyses, a new method is proposed to investigate the storage and preservation of yak meat.

The Antibacterial Activity and Mechanism of Chlorogenic Acid Against Foodborne Pathogen Pseudomonas aeruginosa.

Chlorogenic acid (CA), an ester of caffeic acid, is a major phenolic compound in herbs. The antimicrobial activity of CA against Pseudomonas aeruginosa P1, a foodborne pathogen, was investigated in this study. To understand how CA injured target cells, the influence of CA on cell morphology was assessed. A sunken cell surface and detachment of outer membrane components in P. aeruginosa P1 were observed after being treated by CA. Following this, the intracellular membrane permeability and the content of lipopolysaccharide (LPS), a main component of outer membrane, were determined. The release of intracellular protein and ATP from P. aeruginosa P1 indicated that CA increased intracellular membrane permeability and resulted in the leakage of intracellular materials. The uptake of propidium iodide, a compromised cell membrane nucleic acid stain, further demonstrated that CA acted on the intracellular membrane. CA resulted in the decrease of LPS contents of P. aeruginosa P1, which supported the detachment of outer membrane. CA also downregulated the expression of major genes in LPS biosynthesis, suggesting that CA may inhibit intracellular metabolism of P. aeruginosa P1 cells. Thus, CA increased the intracellular membrane permeability, induced the exfoliation of outer membrane, and disturbed the intracellular metabolism. Damage of intracellular and outer membranes as well as disruption of cell metabolism resulted in cell death eventually. The finding suggested that CA has the potential to be developed as a preservative to control P. aeruginosa-associated foodborne diseases.

Optimization of Antioxidant Hydrolysate Produced from Tibetan Egg White with Papain and Its Application in Yak Milk Yogurt.

The objective of the present study was to produce antioxidant hydrolysate from Tibetan egg white protein hydrolyzed with papain, and to investigate the effect of added papain egg white hydrolysate (PEWH) on the quality characteristics and amino acid profiles of yak milk yogurt. A response surface methodology (RSM) was utilized to analyze the effects of hydrolysis time (X1), the ratio of enzymes to substrates, and enzyme dosage (X3) on the superoxide anion radical (O2-) scavenging activity of hydrolysates. The predicted maximum value of O2- scavenging activity (89.06%) was obtained an X1 of 2.51 h, X2 of 4.13%, and X3 of 4500 U/g of substrate, almost approaching the experimental value (88.05 ± 1.2%). Furthermore, it was found that the addition of PEWH to yak milk can enhance acidification, sensory score, the number of lactic acid bacteria (LAB), and the amino acid content in yak milk yogurt. The results suggested that PEWH displayed an exceptional potential to be developed as a functional food ingredient that could be applied during the manufacturing process of yak milk yogurt.

Effects of dietary resveratrol supplementation during gestation and lactation of sows on milk composition of sows and fat metabolism of sucking piglets.

The purpose of this article was to investigate the effects of dietary resveratrol supplementation during gestation and lactation of sows on the milk composition of sows and the fat metabolism of sucking piglets. Forty sows were allotted to two experimental treatment groups that included the following: (a) control sows (CON treatment, n = 20) fed with a corn-soybean meal control diet and (b) treatment sows (RES treatment, n = 20) fed with a control diet with addition of 300 mg/kg resveratrol. The results showed that the content of lactose in the colostrum was increased (p < 0.05) and the content of fat in 21-day milk was increased (p < 0.05) by dietary resveratrol supplementation. In the RES treatment group, the concentrations of high-density lipoprotein-cholesterol (HDL-C), low-density lipoprotein-cholesterol (LDL-C), lipase activity and insulin (INS) in plasma of sucking piglets were increased (p < 0.05). In the adipose tissue, the enzyme activities of hormone-sensitive lipase (HSL), acetyl-CoA carboxylase (ACC) and lipoprotein lipase (LPL) increased significantly by RES treatment (p < 0.05), and the mRNA levels of acetyl coenzyme A-alpha (ACCα), LPL, fatty acid transport protein (FATP1) and CCAAT-enhancer-binding protein gene (C/EBPα) were higher in the RES treatment group (p < 0.05). In conclusion, resveratrol supplementation on gestational and lactating sows improved the content of lactose in the colostrum and the content of fat in milk at day 21 of lactation. In addition, resveratrol supplementation on sows increased HDL and LDL in the plasma of piglets. In piglet adipose tissue, the enzyme activity and mRNA level related to lipolysis, fatty acid uptake from circulating triacylglycerols and lipogenesis are partially improved by resveratrol supplementation on sows. These aspects affect fat metabolism in piglets.

Engineering Surface Patterning of Colloidal Rings through Plateau-Rayleigh Instability.

Plateau-Rayleigh (P-R) instability occurring on Brownian colloidal particles is presented. This instability can be used for the surface patterning of Brownian colloidal rings. This idea was realized by employing polystyrene(PS)/SiO2 core/shell rings, for which PS layer was selectively grown onto the interior surface of SiO2 rings. The P-R instability was initiated in the ring's dispersion by adding a good solvent of PS. By using both experiments and theory, it is shown that the number of patches is tunable and that it is linearly related to a function of two variables, namely, solvent quantity and contact angle. In particular, one-patch Janus rings and patchy disks were also synthesized at high yields. The patch size of all particles is tunable by step-by-step polymerization and the patches can be functionalized, for example by ATRP grafting with pH-sensitive polymers. This approach can be adapted for the synthesis of other patchy colloids with designated complexity.

A micro-/nano-chip and quantum dots-based 3D cytosensor for quantitative analysis of circulating tumor cells.

BACKGROUND: Due to the high transfer ability of cancer cell, cancer has been regarded as a world-wide high mortality disease. Quantitative analysis of circulating tumor cells (CTCs) can provide some valuable clinical information that is particularly critical for cancer diagnosis and treatment. Along with the rapid development of micro-/nano-fabrication technique, the three-dimensional (3D) bionic interface-based analysis method has become a hot research topic in the area of nanotechnology and life science. Micro-/nano-structure-based devices have been identified as being one of the easiest and most effective techniques for CTCs capture applications. METHODS: We demonstrated an electrospun nanofibers-deposited nickel (Ni) micropillars-based cytosensor for electrochemical detection of CTCs. Breast cancer cell line with rich EpCAM expression (MCF7) were selected as model CTCs. The ultra-long poly (lactic-co-glycolic acid) (PLGA) nanofibers were firstly-crosswise stacked onto the surface of Ni micropillars by electrospinning to construct a 3D bionic interface for capturing EpCAM-expressing CTCs, following immuno-recognition with quantum dots functionalized anti-EpCAM antibody (QDs-Ab) and forming immunocomplexes on the micro-/nano-chip. RESULTS: The Ni micropillars in the longitudinal direction not only play a certain electrical conductivity in the electrochemical detection, but also its special structure improves the efficiency of cell capture. The cross-aligned nanofibers could simulate the extracellular matrix to provide a good microenvironment which is better for cell adhesion and physiological functions. Bioprobe containing quantum dots will release Cd2+ in the process of acid dissolution, resulting in a change in current. Beneath favourable conditions, the suggested 3D cytosensor demonstrated high sensitivity with a broad range of 101-105 cells mL-1 and a detection limit of 8 cells mL-1. CONCLUSIONS: We constructed a novel 3D electrochemical cytosensor based on Ni micropillars, PLGA electrospun nanofibers and quantum dots bioprobe, which could be used to highly sensitive and selective analysis of CTCs. More significantly, the 3D cytosensor can efficiently identify CTCs from whole blood, which suggested the potential applications of our technique for the clinical diagnosis and therapeutic monitoring of cancers.