Editorial for the Special Issue on Advances in Micro and Nano Manufacturing: Process Modeling and Applications, Volume II.

In the second volume of the Special Issue on 'Advances in Micro and Nano Manufacturing: Process Modeling and Applications', we continue to witness the dynamic evolution of micro- and nanomanufacturing technologies [...].

The Effects of Nucleating Agents and Processing on the Crystallization and Mechanical Properties of Polylactic Acid: A Review.

Polylactic acid (PLA) is a biobased, biodegradable, non-toxic polymer widely considered for replacing traditional petroleum-based polymer materials. Being a semi-crystalline material, PLA has great potential in many fields, such as medical implants, drug delivery systems, etc. However, the slow crystallization rate of PLA limited the application and efficient fabrication of highly crystallized PLA products. This review paper investigated and summarized the influence of formulation, compounding, and processing on PLA's crystallization behaviors and mechanical performances. The paper reviewed the literature from different studies regarding the impact of these factors on critical crystallization parameters, such as the degree of crystallinity, crystallization rate, crystalline morphology, and mechanical properties, such as tensile strength, modulus, elongation, and impact resistance. Understanding the impact of the factors on crystallization and mechanical properties is critical for PLA processing technology innovations to meet the requirements of various applications of PLA.

Crystallization of Polylactic Acid with Organic Nucleating Agents under Quiescent Conditions.

Polylactic acid (PLA) is a versatile and sustainable polymer used in various applications. This research explores the use of orotic acid (OA) and ethylene bis-stearamide (EBS) as nucleating agents to enhance the quiescent crystallization of PLA within the temperature range of 80 °C to 140 °C. Different blends were produced via melt processing before analyzing via DSC, XRD, and SEM. Our results show that both nucleating agents significantly accelerated the crystallization process and reduced the incubation time and the crystallization half-time. The most promising results were obtained with 1% EBS at 110 °C, achieving the fastest crystallization. The XRD analysis showed that at 80 °C, the disordered α'phase predominated, while more stable α phases formed at 110 °C and 140 °C. Combining the 1% nucleating agent and 110 °C promotes densely packed crystalline lamellae. The nucleated PLA exhibited a well-organized spherulitic morphology in agreement with the Avrami modeling of DSC data. Higher nucleating agent concentrations yielded smaller, more evenly distributed crystalline domains. Utilizing OA or EBS in PLA processing could offer enhanced properties, improved processability, and cost-efficiency, making PLA more competitive in various applications.

Wetting Characteristics of Laser-Ablated Hierarchical Textures Replicated by Micro Injection Molding.

Texturing can be used to functionalize the surface of plastic parts and, in particular, to modify the interaction with fluids. Wetting functionalization can be used for microfluidics, medical devices, scaffolds, and more. In this research, hierarchical textures were generated on steel mold inserts using femtosecond laser ablation to transfer on plastic parts surface via injection molding. Different textures were designed to study the effects of various hierarchical geometries on the wetting behavior. The textures are designed to create wetting functionalization while avoiding high aspect ratio features, which are complex to replicate and difficult to manufacture at scale. Nano-scale ripples were generated over the micro-scale texture by creating laser-induced periodic surface structures. The textured molds were then replicated by micro-injection molding using polypropylene and poly(methyl methacrylate). The static wetting behavior was investigated on steel inserts and molded parts and compared to the theoretical values obtained from the Cassie-Baxter and Wenzel models. The experimental results showed correlations between texture design, injection molding replication, and wetting properties. The wetting behavior on the polypropylene parts followed the Cassie-Baxter model, while for PMMA, a composite wetting state of Cassie-Baxter and Wenzel was observed.

Texturing Technologies for Plastics Injection Molding: A Review.

Texturing is an engineering technology that can be used to enable surface functionalization in the plastics injection molding industry. A texture is defined as the geometrical modification of the topography by addition of surface features that are characterized by a smaller scale than the overall surface dimensions. Texturing is added to products to create novel functionalities of plastic products and tools, which can be exploited to modify interactions with other materials in contact with the surface. The geometry, dimensions, and positioning on the surface define the function of a texture and its properties. This work reviews and discuss the wide range of texturing technologies available in the industry. The advantages and limitations of each technology are presented to support the development of new surface engineering applications in the plastics manufacturing industry.

An Investigation on the Efficacy of Orotic Acid as a Bio-Nucleating Agent for Poly-Lactic Acid under Quiescent Condition and Injection Molding.

Polylactic acid (PLA) is a bio-based biodegradable polymer and is considered to be an environmentally friendly alternative to petroleum-based polymers for various applications. Neat PLA requires an extended period at elevated temperatures to attain its maximum crystallinity, which can be mitigated by the addition of nucleating agents. Orotic acid is a natural heterocyclic nucleating agent in PLA. The effect of orotic acid on the crystallization behavior of a commercial, high-purity PLA was studied in detail. A differential scanning calorimetry (DSC) technique was utilized for this purpose. A new protocol for the quantitative characterization of crystallization kinetics from DSC data was developed. It was found that the total crystallinity increased from 26% to 63% at 80 °C with 1% content of orotic acid. Meanwhile, the crystallization rate of PLA-OA blends increased by ~10 times as compared to neat PLA. The addition of orotic acid also reduced the incubation time by >17% under quiescent conditions. Injection molding experiments showed that highly crystallized (>50%) PLA samples could be fabricated with a 1% addition of orotic acid. The required mold temperature was reduced from the 120 °C recommended by the supplier to 80 °C.

Editorial for the Special Issue on Advances in Micro and Nano Manufacturing: Process Modeling and Applications.

Micro- and nano-manufacturing technologies have been developed in research and industrial environments to support product miniaturization and the integration of new functionalities [...].

Characterization of Stereolithography Printed Soft Tooling for Micro Injection Molding.

The use of microfeature-enabled devices, such as microfluidic platforms and anti-fouling surfaces, has grown in both potential and application in recent years. Injection molding is an attractive method of manufacturing these devices due to its excellent process throughput and commodity-priced raw materials. Still, the manufacture of micro-structured tooling remains a slow and expensive endeavor. This work investigated the feasibility of utilizing additive manufacturing, specifically a Digital Light Processing (DLP)-based inverted stereolithography process, to produce thermoset polymer-based tooling for micro injection molding. Inserts were created with an array of 100-µm wide micro-features, having different heights and thus aspect ratios. These inserts were molded with high flow polypropylene to investigate print process resolution capabilities, channel replication abilities, and insert wear and longevity. Samples were characterized using contact profilometry as well as optical and scanning electron microscopies. Overall, the inserts exhibited a maximum lifetime of 78 molding cycles and failed by cracking of the entire insert. Damage was observed for the higher aspect ratio features but not the lower aspect ratio features. The effect of the tool material on mold temperature distribution was modeled to analyze the impact of processing and mold design.

Functionalization of Plastic Parts by Replication of Variable Pitch Laser-Induced Periodic Surface Structures.

Surface functionalization of plastic parts has been studied and developed for several applications. However, demand for the development of reliable and profitable manufacturing strategies is still high. Here we develop and characterize a new process chain for the versatile and cost-effective production of sub-micron textured plastic parts using laser ablation. The study includes the generation of different sub-micron structures on the surface of a mold using femtosecond laser ablation and vario-thermal micro-injection molding. The manufactured parts and their surfaces are characterized in consideration of polymer replication and wetting behavior. The results of the static contact angle measurements show that replicated Laser-Induced Periodic Surface Structures (LIPSSs) always increase the hydrophobicity of plastic parts. A maximum contact angle increase of 20% was found by optimizing the manufacturing thermal boundary conditions. The wetting behavior is linked to the transition from a Wenzel to Cassie-Baxter state, and is crucial in optimizing the injection molding cycle time.

Hybrid Process Chain for the Integration of Direct Ink Writing and Polymer Injection Molding.

The integration of additive manufacturing direct-writing technologies with injection molding provides a novel method to combine functional features into plastic products, and could enable mass-manufacturing of custom-molded plastic parts. In this work, direct-write technology is used to deposit conductive ink traces on the surface of an injection mold. After curing on the mold surface, the printed trace is transferred into the plastic part by exploiting the high temperature and pressure of a thermoplastic polymer melt flow. The transfer of the traces is controlled by interlocking with the polymer system, which creates strong plastic/ink interfacial bonding. The hybrid process chain uses designed mold/ink surface interactions to manufacture stable ink/polymer interfaces. Here, the process chain is proposed and validated through systematic interfacial analysis including feature fidelity, mechanical properties, adhesion, mold topography, surface energy, and hot polymer contact angle.