Few-mode multi-element fiber amplifier for mode division multiplexing.

We experimentally demonstrate a few-moded cladding-pumped multi-element fiber amplifier, comprising 4 Er/Yb co-doped signal fibers and 1 multimode pump-delivery fiber all of which are drawn together in a common polymer coating, providing a total spatial path multiplicity of 12. An average WDM signal gain of 18.3 dB and differential modal gain of 1.1 dB were achieved in the spectral range of 1542-1560 nm.

Multi-element fiber technology for space-division multiplexing applications.

A novel technological approach to space division multiplexing (SDM) based on the use of multiple individual fibers embedded in a common polymer coating material is presented, which is referred to as Multi-Element Fiber (MEF). The approach ensures ultralow crosstalk between spatial channels and allows for cost-effective ways of realizing multi-spatial channel amplification and signal multiplexing/demultiplexing. Both the fabrication and characterization of a passive 3-element MEF for data transmission, and an active 5-element erbium/ytterbium doped MEF for cladding-pumped optical amplification that uses one of the elements as an integrated pump delivery fiber is reported. Finally, both components were combined to emulate an optical fiber network comprising SDM transmission lines and amplifiers, and illustrate the compatibility of the approach with existing installed single-mode WDM fiber systems.

Cladding pumped few-mode EDFA for mode division multiplexed transmission.

We experimentally demonstrate a few-mode erbium doped fiber amplifier (FM-EDFA) supporting 6 spatial modes with a cladding pumped architecture. Average modal gains are measured to be >20dB between 1534nm-1565nm with a differential modal gain of ~3dB among the mode groups and noise figures of 6-7dB. The cladding pumped FM-EDFA offers a cost effective alternative to core-pumped variant as low cost, high power multimode pumps can be used, and offers performance, scalability and simplicity to FM-EDFA design.

Erbium-doped multi-element fiber amplifiers for space-division multiplexing operations.

Erbium-doped multi-element fiber (MEF) amplifiers have been fabricated to simultaneously amplify multiple transmission channels. MEF devices comprise of multiple single-core fibers (elements) combined in a common coating, with each element working as a single fiber in isolation. MEFs containing 3-elements and 7-elements have been fabricated and characterized. Each element of the fabricated MEFs provides nearly 32 dB of gain with a noise figure of <5 dB for an input signal level of -23 dBm at 1530 nm. Different permutations of element pairs within the MEFs were checked for crosstalk and none was detected, confirming the simultaneous multi-channel amplification capabilities of MEFs.

Q-switched neodymium-doped Y3Al5O12-based silica fiber laser.

We present pulsed laser operation in a Nd-doped, Y3Al5O12-based silica fiber. The fiber was fabricated using the rod-in-tube technique with a Nd:YAG crystal rod as the core material and a silica tube for the cladding material. A spectroscopy study revealed that the core region had become amorphous in the process of fiber drawing. Q-switched pulsed laser operation was realized at a wavelength of 1058 nm when the fiber was cladding pumped at a wavelength of 808 nm. The laser delivered 38 µJ of energy in 65 ns pulses. The extracted energy was limited due to the multimodal operation of the fiber. Laser slope efficiency in continuous wave operation reached 52%. The spectroscopic properties of the fabricated fiber are discussed and compared to a Nd:YAG crystal and a Nd:Al-doped silica fiber.

Design and performance of a ZnSe tetra-prism for homogeneous substrate heating using a CO2 laser for pulsed laser deposition experiments.

We report on the design and performance of a ZnSe tetra-prism for homogeneous substrate heating using a continuous wave CO(2) laser beam in pulsed laser deposition experiments. We discuss here three potential designs for homogenizing prisms and use ray-tracing modeling to compare their operation to an alternative square-tapered beam-pipe design. A square-pyramidal tetra-prism design was found to be optimal and was subjected to modeling and experimental testing to determine the influence of interference and diffraction effects on the homogeneity of the resultant intensity profile produced at the substrate surface. A heat diffusion model has been used to compare the temperature distributions produced when using various different source intensity profiles. The modeling work has revealed the importance of substrate thickness as a thermal diffuser in producing a resultant homogeneous substrate temperature distribution.