Emergence and spread of SARS-CoV-2 variants of concern in Canada: a retrospective analysis from clinical and wastewater data.

BACKGROUND: The spread of SARS-CoV-2 has been studied at unprecedented levels worldwide. In jurisdictions where molecular analysis was performed on large scales, the emergence and competition of numerous SARS-CoV-2lineages have been observed in near real-time. Lineage identification, traditionally performed from clinical samples, can also be determined by sampling wastewater from sewersheds serving populations of interest. Variants of concern (VOCs) and SARS-CoV-2 lineages associated with increased transmissibility and/or severity are of particular interest. METHOD: Here, we consider clinical and wastewater data sources to assess the emergence and spread of VOCs in Canada retrospectively. RESULTS: We show that, overall, wastewater-based VOC identification provides similar insights to the surveillance based on clinical samples. Based on clinical data, we observed synchrony in VOC introduction as well as similar emergence speeds across most Canadian provinces despite the large geographical size of the country and differences in provincial public health measures. CONCLUSION: In particular, it took approximately four months for VOC Alpha and Delta to contribute to half of the incidence. In contrast, VOC Omicron achieved the same contribution in less than one month. This study provides significant benchmarks to enhance planning for future VOCs, and to some extent for future pandemics caused by other pathogens, by quantifying the rate of SARS-CoV-2 VOCs invasion in Canada.

Adsorption of sulfamethoxazole and lincomycin from single and binary aqueous systems using acid-modified biochar from activated sludge biomass.

The extensive use of pharmaceuticals has raised growing concerns regarding their presence in surface waters. High concentrations of sulfamethoxazole (SMX) and lincomycin (LIN), as commonly prescribed antibiotics, persist in various wastewaters and surface waters, posing risks to public health and the environment. Biochar derived from accessible biowaste, like activated sludge biomass, offers a sustainable and eco-friendly solution to mitigate antibiotic release into water systems. This study investigates the effectiveness of H3PO4-modified activated sludge-based biochar (PBC) synthesized through microwave (MW) heating for the adsorption of SMX and LIN antibiotics. The synthesis parameters of PBC were optimized using a central composite design considering MW power, time, and H3PO4 concentration. Characterization results validate the efficacy of the synthesis process creating a specific surface area of 365 m2/g, and well-developed porosity with abundant oxygen-containing functional groups. Batch and dynamic adsorption experiments were piloted to assess the adsorption performance of PBC in single and binary antibiotic systems. Results show that PBC exhibits a higher affinity for SMX rather than LIN, with maximum adsorption capacities of 45.6 mg/g and 26.6 mg/g, respectively. Based on kinetic studies chemisorption is suggested as the primary mechanism for SMX and LIN removal. Equilibrium studies show a strong agreement with the Redlich-Peterson isotherm, suggesting a composite adsorption mechanism with a greater probability of multilayer adsorption for both antibiotics. Hydrogen bonding and π-π electron sharing are suggested as the prevailing adsorption mechanisms of SMX and LIN on the modified biochar. Furthermore, a dynamic adsorption system was replicated using a fixed bed column setup, demonstrating effective removal of SMX and LIN from pure water and real wastewater samples using PBC-loaded hydrogel beads (PBC-B). These findings serve as crucial support for upcoming studies concerning the realistic application of sludge-based biochar in the removal of antibiotics from water systems.

Treatment of aqueous arsenic - A review of biosorbent preparation methods.

Arsenic (As) is a worldwide human health issue with the major exposure route being the consumption of As-contaminated drinking water. Sorption is considered to be an efficient treatment method, among other technologies, for As removal from various water and wastewater matrices. There are common commercially available sorbents, however, the use of locally or regionally available biomasses have recently been of interest as potentially cost-effective and environmentally friendly alternatives. Despite these benefits, untreated biomasses often show low sorption capacity, can be too fragile, and can lead to coloration of waters when used in treatment processes. Treatment methods of biomasses can include chemical processes using acid or alkaline solutions, developing of biomass composite by deposition of activating agents, and preparation of biochars. This review includes an overview of 53 recent studies that assess a variety of biomass modification methods meant to overcome these issues such as activation with acids or bases and biomass-based composites. Furthermore, future perspectives have been provided to assist in the further optimization of methods for biomass modifications to enhance their As sorption capacities.

Dynamics of microbial community structure and nutrient removal from an innovative side-stream enhanced biological phosphorus removal process.

Biological phosphorous (P) and nitrogen (N) removal from municipal wastewater was studied using an innovative anoxic-aerobic-anaerobic side-stream treatment system. The impact of influent water quality including chemical oxygen demand (COD), ammonium and orthophosphate concentrations on the reactor performance was evaluated. The results showed the system was very effective at removing both COD (>88%) and NH4+-N (>96%) despite varying influent concentrations of COD, NH4+-N, and total PO43--P. In contrast, it was found that the removal of P was sensitive to influent NH4+-N and PO43--P concentrations. The maximum PO43--P removal of 79% was achieved with the lowest influent NH4+-N and PO43--P concentration. Quantitative PCR (qPCR) assays showed a high abundance and diversity of phosphate accumulating organisms (PAO), nitrifiers and denitrifiers. The MiSeq microbial community structure analysis showed that the Proteobacteria (especially ß-Proteobacteria, and γ-Proteobacteria) were the dominant in all reactors. Further analysis of the bacteria indicated the presence of diverse PAO genera including Candidatus Accumulibacter phosphatis, Tetrasphaera, and Rhodocyclus, and the denitrifying PAO (DPAO) genus Dechloromonas. Interestingly, no glycogen accumulating organisms (GAOs) were detected in any of the reactors, suggesting the advantage of proposed process in term of PAO selection for enhanced P removal compared with conventional main-stream processes.

Wastewater Colloidal Organic Carbon: Characterization of Filtration Fractions Using 1H NMR.

The current study separates colloidal organic carbon (COC) of municipal wastewater using membrane and ultrafiltration filters followed by characterization using 1H nuclear magnetic resonance (NMR) and UV absorbance with the goal of determination of size-specific characteristics, which may be used to correlate contaminant partitioning to natural COC. Passing fractions included 49.7, 44.8, 39.3, and 33.1 mg/L COC for filter sizes 1.5 µm, 0.45 µm, 100 kDa, and 1 kDa, respectively. The methodology used for processing COC prior to 1H NMR characterization was novel and successful in concentrating COC without modification of structures, which is the general drawback of other separation techniques such as resin extractions. This concentration technique is quite simple (i.e., not dependent on specialized instrumentation) and allows much shorter NMR experimental durations saving time and cost of analysis. Further work using NMR techniques will allow for greater understanding of COC molecular characteristics and be valuable for use in predictive modeling improvements.

Next-generation pyrosequencing analysis of microbial biofilm communities on granular activated carbon in treatment of oil sands process-affected water.

The development of biodegradation treatment processes for oil sands process-affected water (OSPW) has been progressing in recent years with the promising potential of biofilm reactors. Previously, the granular activated carbon (GAC) biofilm process was successfully employed for treatment of a large variety of recalcitrant organic compounds in domestic and industrial wastewaters. In this study, GAC biofilm microbial development and degradation efficiency were investigated for OSPW treatment by monitoring the biofilm growth on the GAC surface in raw and ozonated OSPW in batch bioreactors. The GAC biofilm community was characterized using a next-generation 16S rRNA gene pyrosequencing technique that revealed that the phylum Proteobacteria was dominant in both OSPW and biofilms, with further in-depth analysis showing higher abundances of Alpha- and Gammaproteobacteria sequences. Interestingly, many known polyaromatic hydrocarbon degraders, namely, Burkholderiales, Pseudomonadales, Bdellovibrionales, and Sphingomonadales, were observed in the GAC biofilm. Ozonation decreased the microbial diversity in planktonic OSPW but increased the microbial diversity in the GAC biofilms. Quantitative real-time PCR revealed similar bacterial gene copy numbers (>10(9) gene copies/g of GAC) for both raw and ozonated OSPW GAC biofilms. The observed rates of removal of naphthenic acids (NAs) over the 2-day experiments for the GAC biofilm treatments of raw and ozonated OSPW were 31% and 66%, respectively. Overall, a relatively low ozone dose (30 mg of O3/liter utilized) combined with GAC biofilm treatment significantly increased NA removal rates. The treatment of OSPW in bioreactors using GAC biofilms is a promising technology for the reduction of recalcitrant OSPW organic compounds.

Probing the adsorption of weak acids on graphite using amplitude modulation-frequency modulation atomic force microscopy.

Recent thermodynamics calculations and adsorption isotherms showed that the adsorption of a self-assembled layer (SAL) of ionized weak acids to carbon was attributed to the negatively charged hydrogen bonding (-CAHB), yet the direct visualization and characterization of this adsorption behavior have not been reported. Here, an amplitude modulation-frequency modulation atomic force microscopy (AM-FM AFM) technique was applied to discriminate the adsorption of decanoic acids (DA) on highly ordered pyrolytic graphite (HOPG). Thermodynamics calculations revealed that the adsorption of SAL was driven by the formation of -CAHB with negatively charged functional groups of HOPG. Multilayer adsorption could occur over the adsorbed ionized SAL, leading to the development of aggregates. AM-FM AFM imaging showed that the adsorption of the DA molecules forming aggregates occurred only for the HOPG-functionalized steps, while DA molecules were found to adsorb over the entire functionalized HOPG surface after water-plasma treatment, as evident from the frequency shifts identified in AFM images.

Ultra Performance Liquid Chromatography Ion Mobility Time-of-Flight Mass Spectrometry Characterization of Naphthenic Acids Species from Oil Sands Process-Affected Water.

Ultraperformance liquid chromatography ion mobility time-of-flight mass spectrometry (UPLC-IM-TOFMS), integrating traveling wave ion mobility spectrometry (TWIMS) with negative electrospray ionization (ESI) mode, was used to achieve two-dimensional (2D) separation (drift vs retention times) of naphthenic acids (NAs). Unprocessed and ozonated commercial NAs were used for method development. Only O2-NAs were found in unprocessed NAs with ozonation creating O3-NAs and O4-NAs. Unprocessed and ozonated oil sands process-affected waters (OSPW) were examined to validate the method for complex matrix NAs. Ozonation increased the x number for Ox-NAs (2 ≤ x ≤ 5) and also impacted the -Z number distribution. OSPW extracted using dichloromethane removed the potential for sample matrix impacts and was used for MS/MS NAs characterization. The Ox-NAs (2 ≤ x ≤ 6) were identified with O2-NAs separated into three clusters indicating isobaric and isomeric species. MS/MS was used to verify compounds, while also indicating the presence of CH3CH2S- NAs groups. This result may be useful for future studies of sulfur-NAs fate, toxicity, and treatment. Overall, the value-added information provided by UPLC-IM-TOFMS makes it a promising analytical technique for analysis of NAs in complex OSPW samples. Moreover, this methodology can be used for other matrices to investigate relative molecular sizes and to separate complex species (e.g., fatty acids, lipids), making it beneficial for environmental and bioanalytical applications.

Coagulation/flocculation process with polyaluminum chloride for the remediation of oil sands process-affected water: Performance and mechanism study.

This study investigated the application of polyaluminum chloride (PACl) for the treatment of the oil sands process-affected water (OSPW). These coagulants are commonly used in water treatment with the most effective species reported to be Al13. PACl with 83.6% Al13 was synthesized using the slow base titration method and compared with a commercially available PACl in terms of aluminum species distribution, coagulation/flocculation (CF) performance, floc morphology, and contaminant removal. Both coagulants were effective in removing suspended solids, achieving over 96% turbidity removal at all applied coagulant doses (0.5-3.0 mM Al). The removal efficiencies of metals varied among different metals depending on their pKa values with metal cations having pKa values (Fe, Al, Ga, and Ti) below OSPW pH of 6.9-8.1 (dose dependent) being removed by more than 90%, while cations with higher pKa values (K, Na, Ca, Mg and Ni) had removals of less than 40%. Naphthenic acids were not removed due to their low molecular weights, negative charges, and hydrophilic characteristics at the OSPW pH. At the highest applied coagulant dose of 3.0 mM Al, the synthetic PACl reduced Vibrio fischeri inhibition effect to 43.3 ± 3.0% from 49.5 ± 0.4% in raw OSPW. In contrast, no reduction of toxicity was found for OSPW treated with the commercial PACl. Based on water quality and floc analyses, the dominant CF mechanism for particle removal during OSPW treatment was considered to be enmeshment in the precipitates (i.e., sweep flocculation). Overall, the CF using synthesized PACl can be a valuable pretreatment process for OSPW to create wastewater that is more easily treated by downstream processes.

Granular activated carbon for simultaneous adsorption and biodegradation of toxic oil sands process-affected water organic compounds.

Naphthenic acids (NAs) released into oil sands process-affected water (OSPW) during bitumen processing in Northern Alberta are problematic for oil sands industries due to their toxicity in the environment and resistance to degradation during conventional wastewater treatment processes. Granular activated carbon (GAC) has shown to be an effective media in removing biopersistent organics from wastewater using a combination of adsorption and biodegradation removal mechanisms. A simultaneous GAC (0.4 g GAC/L) adsorption and biodegradation (combined treatment) study was used for the treatment of raw and ozonated OSPW. After 28 days of batch treatment, classical and oxidized NAs removals for raw OSPW were 93.3% and 73.7%, and for ozonated OSPW were 96.2% and 77.1%, respectively. Synergetic effects of the combined treatment process were observed in removals of COD, the acid extractable fraction, and oxidized NAs, which indicated enhanced biodegradation and bioregeneration in GAC biofilms. A bacteria copy number >10(8) copies/g GAC on GAC surfaces was found using quantitative real time polymerase chain reaction after treatment for both raw and ozonated OSPW. A Microtox(®) acute toxicity test (Vibrio fischeri) showed effective toxicity removal (>95.3%) for the combined treatments. Therefore, the simultaneous GAC adsorption and biodegradation treatment process is a promising technology for the elimination of toxic OSPW NAs.

Investigation of mono/competitive adsorption of environmentally relevant ionized weak acids on graphite: impact of molecular properties and thermodynamics.

The thermodynamics of adsorption and competitive interactions of five weak acids on a graphite surface was assessed in alkaline solutions. Adsorption of the acids in mono- and multicompound solutions followed their Freundlich isotherms which suggest a diversity of graphite adsorption sites as confirmed by the presence of carboxylic and phenolic groups observed on graphite surfaces. Thermodynamic calculations assigned the formation of the negatively charged assisted hydrogen bond (-CAHB) between ionized solutes and adsorbent surface groups as the possible adsorption mechanism. However, the similar pKa values of current acids resulted in comparable free energies for -CAHB formation (ΔG(-CAHB)) being less than solvation free energies (ΔGSolv). Thus, additional ΔG is supplemented by increased hydrophobicity due to proton exchange of ionized acids with water (ΔΔG Hydrophobicity). Adsorption capacities and competition coefficients indicated that ΔΔG Hydrophobicity values depend on the neutral and ionized acid Kow. Competitive adsorption implies that multilayer adsorption may occur via hydrophobic bonding with the CH3 ends of the self-assembled layer which affects the acid adsorption capacities in mixtures as compared to monocompound solutions. The determination of adsorption mechanisms will assist in understanding of the fate and bioavailability of emerging and classical weak acids released into natural waters.

Advanced analytical mass spectrometric techniques and bioassays to characterize untreated and ozonated oil sands process-affected water.

Oil sands process-affected water (OSPW) is a toxic and poorly biodegradable mixture of sand, silt, heavy metals, and organics. In this study, qualitative and quantitative comparisons of naphthenic acids (NAs) were done using ultraperformance liquid chromatography time-of-flight mass spectrometry (UPLC TOF-MS), Fourier transform ion cyclotron resonance (FT-ICR) MS, and ion mobility spectrometry (IMS). The unique combination of these analyses allowed for the determination and correlation of NAs, oxidized NAs, and heteroatom (sulfur or nitrogen) NAs. Despite its lower resolution, UPLC-TOF MS was shown to offer a comparable level of reliability and precision as the high resolution FT-ICR MS. Additionally, the impacts of ozonation (35 mg/L utilized ozone dose) and subsequent NAs degradation on OSPW toxicity were assessed via a collection of organisms and toxicity end points using Vibrio fischeri (nonspecific), specific fish macrophage antimicrobial responses, and fish olfactory responses. Fish macrophages exposed to ozonated OSPW for 1 week showed higher production of reactive oxygen and nitrogen intermediates; however, after 12 weeks the responses were reduced significantly. Fish olfactory tests suggested that OSPW interfered with their perception of odorants. Current results indicate that the quantification of NAs species, using novel analytical methods, can be combined with various toxicity methods to assess the efficiency of OSPW treatment processes.

Impact of ozonation pre-treatment of oil sands process-affected water on the operational performance of a GAC-fluidized bed biofilm reactor.

Treatment of oil sands process-affected water (OSPW) using biodegradation has the potential to be an environmentally sound approach for tailings water reclamation. This process is both economical and efficient, however, the recalcitrance of some OSPW constituents, such as naphthenic acids (NAs), require the pre-treatment of raw OSPW to improve its biodegradability. This study evaluated the treatment of OSPW using ozonation followed by fluidized bed biofilm reactor (FBBR) using granular activated carbon (GAC). Different organic and hydraulic loading rates were applied to investigate the performance of the bioreactor over 120 days. It was shown that ozonation improved the adsorption capacity of GAC for OSPW and improved biodegradation by reducing NAs cyclicity. Bioreactor treatment efficiencies were dependent on the organic loading rate (OLR), and to a lesser degree, the hydraulic loading rate (HLR). The combined ozonation, GAC adsorption, and biodegradation process removed 62 % of chemical oxygen demand (COD), 88 % of acid-extractable fraction (AEF) and 99.9 % of NAs under optimized operational conditions. Compared with a planktonic bacterial community in raw and ozonated OSPW, more diverse microbial communities were found in biofilms colonized on the surface of GAC after 120 days, with various carbon degraders found in the bioreactor including Burkholderia multivorans, Polaromonas jejuensis and Roseomonas sp.

Tungsten sulfide highly boosted Fe(III)/peroxymonosulfate system for rapid degradation of cyclohexanecarboxylic acid: Performance, mechanisms, and applications.

In this study, the Fe(III)/WS2/peroxymonosulfate (PMS) system was found to remove up to 97% of cyclohexanecarboxylic acid (CHA) within 10 min. CHA is a model compound for naphthenic acids (NAs), which are prevalent in petroleum industrial wastewater. The addition of WS2 effectively activated the Fe(III)/PMS system, significantly enhancing its ability to produce reactive oxidative species (ROS) for the oxidation of CHA. Further experimental results and characterization analyses demonstrated that the metallic element W(IV) in WS2 could provide electrons for the direct reduction of Fe(III) to Fe(II), thus rapidly activating PMS and initiating a chain redox process to produce ROS (SO4•-, •OH, and 1O2). Repeated tests and practical exploratory experiments indicated that WS2 exhibited excellent catalytic performance, reusability and anti-interference capacity, achieving efficient degradation of commercial NAs mixtures. Therefore, applying WS2 to catalyze the Fe(III)/PMS system can overcome speed limitations and facilitate simple, economical engineering applications.

Low adsorption affinity of athabasca oil sands naphthenic acid fraction compounds to a peat-mineral mixture.

Much of the toxicity in oil sands process-affected water in Athabasca oil sands tailings has been attributed to naphthenic acids (NAs) and associated naphthenic acid fraction compounds (NAFCs). Previous work has characterized the environmental behaviour and fate of these compounds, particularly in the context of constructed treatment wetlands. There is evidence that wetlands can attenuate NAFCs in natural and engineered contexts, but relative contributions of chemical, biotic, and physical adsorption with sequestration require deconvolution. In this work, the objective was to evaluate the extent to which prospective wetland substrate material may adsorb NAFCs using a peat-mineral mix (PMM) sourced from the Athabasca Oil Sands Region (AOSR). The PMM and NAFCs were first mixed and then equilibrated across a range of NAFC concentrations (5-500 mg/L) with moderate ionic strength and hardness (∼200 ppm combined Ca2+ and Mg2+) that approximate wetland water chemistry. Under these experimental conditions, low sorption of NAFCs to PMM was observed, where sorbed concentrations of NAFCs were approximately zero mg/kg at equilibrium. When NAFCs and PMM were mixed and equilibrated together at environmentally relevant concentrations, formula diversity increased more than could be explained by combining constituent spectra. The TOC present in this PMM was largely cellulose-derived, with low levels of thermally recalcitrant carbon (e.g., lignin, black carbon). The apparent enhancement of the concentration and diversity of components in PMM/NAFCs mixtures are likely related to aqueous solubility of some PMM-derived organic materials, as post-hoc combination of dissolved components from PMM and NAFCs cannot replicate enhanced complexity observed when the two components are agitated and equilibrated together.

Solid-liquid distribution of SARS-CoV-2 in primary effluent of a wastewater treatment plant.

Distributions of Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) and fecal viral biomarkers between solid and liquid phases of wastewater are largely unknown. Herein, distributions of SARS-CoV-2, Pepper Mild Mottle Virus (PMMoV), and F-RNA bacteriophage group II (FRNAPH-II) were determined by viral RNA RT-qPCR. Comparison of viral recovery using three conventional fractionation methods included membrane filtration, a combination of mid-speed centrifugation and membrane filtration, and high-speed centrifugation. SARS-CoV-2 partitioned to the solids fraction in greater abundance compared to liquid fractions in a combination of mid-speed centrifugation and membrane filtration and high-speed centrifugation, but not in membrane filtration method in a particular assay, while fecal biomarkers (PMMoV and FRNAPH-II) exhibited the reciprocal relationship. The wastewater fractionation method had minimal effects on the solids-liquids distribution for all viral and phage markers tested; however, viral RNA load was significantly greater in solid-liquid fractions viral RNA loads compared with the than whole-wastewater PEG precipitation. A RNeasy PowerWater Kit with PCR inhibitor removal resulted in greater viral RNA loads and lesser PCR inhibition compared to a QIAamp Viral RNA Mini Kit without PCR inhibitor removal. These results support the development of improved methods and interpretation of WBE of SARS-CoV-2. •Distribution of SARS-CoV-2 to liquid and solid portions was addressed.•Addressing PCR inhibition is important in wastewater-based epidemiology.•Fraction methods have minimal effect.

Investigation of hydrophobic organic carbon (HOC) partitioning to 1 kDa fractionated municipal wastewater colloids.

Natural organic matter from the aquatic environment passing a 1 kDa filter has been hypothesized to not contribute appreciably to hydrophobic organic compound (HOC) partitioning; however, to our knowledge this limit has not been verified experimentally for any sorbate/sorbent system. Presently, colloidal organic carbon (COC) < 1 kDa approached 70% of the total COC (<1.5 µm) mass in primary effluent (PE) from a municipal wastewater treatment plant. Partitioning of HOCs 1,2,4,5-tetrachlorobenzene, pentachlorobenzene, and hexachlorobenzene to COC for both 1.5 µm and 1 kDa filtrates of PE was investigated using the gas-stripping technique. Contrary to the hypothesis, significant HOC-COC partitioning to the 1 kDa filtrate was observed with organic carbon-normalized partitioning coefficients (logKCOC) of 4.30, 4.36, and 3.74 for 1,2,4,5-TeCB, PeCB, and HCB, respectively. Further, partitioning to COC < 1 kDa dominated the overall partitioning of the three chlorobenzenes in the 1.5 µm filtrate, and the partitioning behavior did not follow the trend based on hydrophobicity (KOW). The results show that significant partitioning of HOC may occur to OC < 1 kDa and highlights the need for further experiments with other HOCs and COC characterization to better understand and explain the observed partitioning.

Understanding common population markers for SARS-CoV-2 RNA normalization in wastewater - A review.

Wastewater monitoring and epidemiology have seen renewed interest during the recent COVID-19 pandemic. As a result, there is an increasing need to normalize wastewater-derived viral loads in local populations. Chemical tracers, both exogenous and endogenous compounds, have proven to be more stable and reliable for normalization than biological indicators. However, differing instrumentation and extraction methods can make it difficult to compare results. This review examines current extraction and quantification methods for ten common population indicators: creatinine, coprostanol, nicotine, cotinine, sucralose, acesulfame, androstenedione 5-hydroindoleacetic acid (5-HIAA), caffeine, and 1,7-dimethyluric acid. Some wastewater parameters such as ammonia, total nitrogen, total phosphorus, and daily flowrate were also evaluated. The analytical methods included direct injection, dilute and shoot, liquid/liquid, and solid phase extraction (SPE). Creatine, acesulfame, nicotine, 5-HIAA and androstenedione have been analysed by direct injection into LC-MS; however, most authors prefer to include SPE steps to avoid matrix effects. Both LC-MS and GC-MS have been successfully used to quantify coprostanol in wastewater, and the other selected indicators have been quantified successfully with LC-MS. Acidification to stabilize the sample before freezing to maintain the integrity of samples has been reported to be beneficial. However, there are arguments both for and against working at acidic pHs. Wastewater parameters mentioned earlier are quick and easy to quantify, but the data does not always represent the human population effectively. A preference for population indicators originating solely from humans is apparent. This review summarises methods employed for chemical indicators in wastewater, provides a basis for choosing an appropriate extraction and analysis method, and highlights the utility of accurate chemical tracer data for wastewater-based epidemiology.

Assessment of rapid wastewater surveillance for determination of communicable disease spread in municipalities.

Wastewater surveillance (WS) helps to improve the understanding of the spread of communicable diseases in communities. WS can assist public health decision-makers in the design and implementation of timely mitigation measures. There is an increased need to use reliable, cost-effective, simple, and rapid WS systems, given traditional analytical (or 'gold-standard') programs are instrument/time-intensive, and dependent on highly skilled personnel. This study investigated the application of the portable GeneXpert platform for WS of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), influenza A virus (IAV), influenza B virus (IBV), and respiratory syncytial virus (RSV). The GeneXpert system with the Xpert Xpress-SARS-CoV-2/Flu/RSV test kit uses reverse transcription-quantitative polymerase chain reaction (RT-qPCR) to analyze wastewater samples. From September 2022 through January 2023, wastewater samples were collected from the influents of municipal wastewater treatment plants (MWTPs) of Saskatoon, Prince Albert, and North Battleford in the province of Saskatchewan, Canada. Both raw and concentrated wastewater samples were subjected to the GeneXpert analysis. Results showed that the Saskatoon wastewater viral loads were significantly correlated to Saskatchewan's influenza and COVID-19 clinical cases, with a lead time of 10 days for IAV and a lag time of 4 days for SARS-CoV-2. Additionally, the GeneXpert analysis of the three cities' wastewater samples showed that the raw WS could capture the dynamics of SARS-CoV-2 and IAV due to their correlation with concentrated WS. Interestingly, IBV loads were not detected in any wastewater samples, while the Saskatoon and Prince Albert wastewater samples collected following the 2023 holiday season (end of December and beginning of January) were positive for RSV. This study indicates that the GeneXpert has excellent potential for use in the development of an early warning system for transmissible disease in municipalities and limited-resource communities while simultaneously providing stakeholders with an efficient WS methodology.

A wastewater-based risk index for SARS-CoV-2 infections among three cities on the Canadian Prairie.

Wastewater surveillance (WWS) is useful to better understand the spreading of coronavirus disease 2019 (COVID-19) in communities, which can help design and implement suitable mitigation measures. The main objective of this study was to develop the Wastewater Viral Load Risk Index (WWVLRI) for three Saskatchewan cities to offer a simple metric to interpret WWS. The index was developed by considering relationships between reproduction number, clinical data, daily per capita concentrations of virus particles in wastewater, and weekly viral load change rate. Trends of daily per capita concentrations of SARS-CoV-2 in wastewater for Saskatoon, Prince Albert, and North Battleford were similar during the pandemic, suggesting that per capita viral load can be useful to quantitatively compare wastewater signals among cities and develop an effective and comprehensible WWVLRI. The effective reproduction number (Rt) and the daily per capita efficiency adjusted viral load thresholds of 85 × 106 and 200 × 106 N2 gene counts (gc)/population day (pd) were determined. These values with rates of change were used to categorize the potential for COVID-19 outbreaks and subsequent declines. The weekly average was considered 'low risk' when the per capita viral load was 85 × 106 N2 gc/pd. A 'medium risk' occurs when the per capita copies were between 85 × 106 and 200 × 106 N2 gc/pd. with a rate of change <100 %. The start of an outbreak is indicated by a 'medium-high' risk classification when the week-over-week rate of change was >100 %, and the absolute magnitude of concentrations of viral particles was >85 × 106 N2 gc/pd. Lastly, a 'high risk' occurs when the viral load exceeds 200 × 106 N2 gc/pd. This methodology provides a valuable resource for decision-makers and health authorities, specifically given the limitation of COVID-19 surveillance based on clinical data.