Effect of ascorbic acid and epidermal growth factor in a rat tibia defect.

PURPOSE: Bone repair aims to restore the anatomical, biomechanical, and functional integrity of the affected structure. Here we study the effects of ascorbic acid (AA) and epidermal growth factor (EGF) applied in a single dose and in combination on the repair of a noncritical bone defect model. METHODS: Twenty-four rats were divided into four groups: an intact G-1 control group, and three groups that underwent a noncritical bone defect in the right tibia: G-2 treated with AA, G-3 treated with EGF, and G-4 treated with AA in combination with EGF. After 21 days of treatment, rats were sacrificed, the tibias were dissected and a destructive biomechanical analysis of three-point flexion test was performed in a universal testing machine; the values of stiffness, resistance, maximum energy, and energy at maximum load were statistically compared. RESULTS: G-3 and G-4 recovered the biomechanical properties of strength and stiffness of an intact tibia 3 weeks after their application. Not so the energy and energy at maximum load. For G-2, only the stiffness of an intact tibia was recovered. CONCLUSIONS: EGF and AA-EGF applied to a noncritical bone defect in the rat tibia favors the recovery of bone resistance and stiffness.

Enhancement of cometabolic biodegradation of 4-chlorophenol induced with phenol and glucose as carbon sources by Comamonas testosteroni.

The biological degradation of phenol and 4-chlorophenol (4-CP) by Comamonas testosteroni CECT 326T has been studied. Phenol and 4-CP were treated alone as a sole carbon and energy source, but only phenol was completely degraded by C. testosteroni. Since the presence of cosubstrates can enhance the toxic compounds removal by pure cultures, phenol and glucose were added as growth substrates for cometabolic transformation of 4-CP. High efficiencies were obtained in all the experiments carried out in presence of both cosubstrates. In spite of the fact that the addition of glucose reduced the lag phase of 4-CP removal, lower phenol concentrations were required to obtain the same degradation efficiencies. The cometabolic transformation of 4-CP was closely related with the extent of phenol removal. The values of the 4-CP/biomass concentration ratio (S/X) obtained for discriminating between complete (S/X ≤ 0.11) and partial 4-CP (S/X ≥ 0.31) transformation showed a narrower range than that reported in the literature. The extent of the cometabolic 4-CP transformation in the presence of phenol could be further enhanced by using glucose as an additional carbon and energy source. However, no significant influence of glucose concentration on 4-CP removal was observed over the concentration range studied.

Hydrogen production from urea in human urine using segregated systems.

Removal of nitrogen compounds through biological processes represents the highest energy consumption in conventional centralised wastewater treatment facilities. Alternatively, segregated systems, where wastewater is treated at its source, present the potential to provide value to nitrogen-rich compounds contained in wastewater like urea. This paper demonstrates the feasibility of a novel process to recover energy from human urine based on the pre-isolation of urea to decrease the energy requirements for its thermal decomposition compared to the conventional thermal treatment when in solution, followed by its decomposition into hydrogen. Herein, urea is separated from an aqueous solution by adsorption onto activated carbon. Thermal urea desorption and decomposition into ammonia and CO2 at 250 °C leads to full regeneration of the carbon, showing a constant adsorption capacity for at least 5 consecutive adsorption/desorption cycles. Finally, when the regeneration and urea decomposition step is coupled to an ammonia decomposition catalyst, hydrogen is produced to be used as an energy fuel. This process opens the door to a new way of circular economy by energy recovery from hydrogen-rich components in segregated wastewater streams. Preliminary energy balances show that the adoption of this energy recovery system in a city of 160,000 inhabitants would lead to a daily hydrogen production of 430 kg, with a net energy production of 2,500 kWh/day. In addition, such waste-to-energy process would lead to energy savings of 4,600 kWh/day in a conventional wastewater treatment plant reducing its energy consumption by around 35%.

Parameterizing a tumor humeral prosthesis and development of a set.

BACKGROUND: The reconstruction of the proximal humerus is possible from the resection of the tumor and the placement of a prosthesis. In some cases, they do not meet the anthropometric aspects of the patients. OBJECTIVE: To determine the parameters to size the components of a humeral prosthesis and the development of a set, using design software. METHOD: Forty patients were selected for prostheses, radiographs and CT scans were analyzed and statistical tests were applied to the measurements. RESULTS: The length of the tumors was 8-20 cm. The minimum length of the humerus was 28 cm and 33 cm the maximum. Correlation was observed between the humerus and the tumor and the height of the patient with p = 0.93088 and p = 0.904564, respectively; humerus diameter, p = 0.2345. The set will include three components, diameter 6-10 mm, and length of 24, 26 and 28 cm. Three modular spacers with lengths of 6, 8.5 and 13 cm. Crowns 6.5 and 8.5 cm long, 1.3 cm in diameter and 5 mm nut. CONCLUSION: With the development of the set, poorly calculated resections and adaptation to any humerus size can be resolved.

ANTECEDENTES: La reconstrucción del húmero proximal es posible a partir de la resección del tumor y la colocación de una prótesis. En algunos casos, las prótesis no cumplen con los aspectos antropométricos de los pacientes. OBJETIVO: Determinar los parámetros para dimensionar los componentes de una prótesis de húmero y el desarrollo de un set, mediante software de diseño. MÉTODO: Se seleccionaron 40 pacientes para prótesis, se analizaron radiografías y tomografías computarizadas, y se aplicaron pruebas estadísticas a las mediciones. RESULTADOS: La longitud de los tumores fue de 8-20 cm. La longitud mínima del húmero fue de 28 cm y la máxima fue de 33 cm. Se observó correlación entre el húmero y el tumor y la altura del paciente, con p = 0.93088 y p = 0.904564, respectivamente; para el diámetro del húmero, p = 0.2345. El set incluye tres componentes, con diámetro de 6-10 mm y longitud de 24, 26 y 28 cm; tres espaciadores modulares con longitudes de 6, 8,5 y 13 cm; coronas de 6,5 y 8,5 cm de largo, 1,3 cm de diámetro y tuerca de 5 mm. CONCLUSIÓN: Con el desarrollo del set se pueden resolver resecciones mal calculadas y la adaptación a cualquier tamaño de húmero.

Catalytic reduction of nitrate with Pd-In2O3.

This work presents a novel catalyst preparation method and the optimization of operation conditions for an effective NO3- conversion with a high selectivity and stability that guarantee water quality for human consumption. Catalytic reduction of NO3- and NO2- was carried out with Pd supported on In2O3 under mild operation conditions (25 °C, 1 atm) with H2 and CO2 as reducing and acidifying agents, respectively. The catalyst was used in batch experiments showing the suppression of NO2- accumulation and low NH4+ selectivity at acid pH. Long-term experiments were carried out with Pd on γ-Al2O3 spheres covered with In2O3. This catalyst presented a high stability during more than 700 h. A concentration of NO3- below 50 mg/L was achieved, producing less than 0.5 mg/L of NH4+ as reaction by-product by a strict limitation of the H2 fed and controlling several operating conditions.

Biogas upgrading, CO2 valorisation and economic revaluation of bioelectrochemical systems through anodic chlorine production in the framework of wastewater treatment plants.

Biogas production in wastewater treatment plants (WWTPs) plays a decisive role in the reduction of CO2 emissions and energy needs in the context of the water-energy nexus. The biogas obtained from sewage sludge digestion can be converted into biomethane by the use of biogas upgrading technologies. In this regard, an innovative water scrubbing based technology, known as ABAD Bioenergy® is presented and considered in this work. The effluents resulting from this system consist of biomethane and treated wastewater with a high CO2 concentration. Therefore, the study explores the feasibility of using this CO2-containing effluent in the cathode of a bioelectrochemical system (BES) for the transformation of CO2 into methane. Techno-economic assessment of the process is presented, including the valorisation of anode reactions through the production of chlorine compounds. Finally, the potential impacts of applying this technology in a WWTP operated by FCC Aqualia are (i) increasing biomethane production by 17.4%, (ii) decreasing CO2 content by 42.8% and (iii) producing over 60 ppm of chlorine compounds to disinfect all the treated wastewater of the plant.

Volumetric measurement of the acetabular cavity in patients with unilateral neglected developmental dysplasia of the dislocated hip operated in a single time.

BACKGROUND: Plain radiography is the most often imaging method used for postoperative assessment of inveterate developmental dysplasia of the hip. This technique does not permit to achieve an accurate diagnose of intra-articular changes, specifically articular congruity. OBJECTIVE: analyze the morphological changes of the acetabular volume by computed tomography, in patients operated by medium adductor myotomy, psoas tenotomy, open hip reduction, diaphysectomy, varus osteotomy and derotating and Dega-type acetabuloplasty. METHOD: A pilot clinical trial was conducted including six patients with unilateral inveterate dysplasia admitted to the Rehabilitation National Institute. Computed tomography were analyzed using an engineering design software. RESULTS: It was found that in all cases analyzed, operated acetabular volume was greater than the contralateral (8 to 48%), however, no significant difference between the volumes was found (p = 2.46). Significant difference between the volume and the age of patients, in multifactorial ANOVA tests (p = 0.006), Cochran's (p = 0.00019) and Kruskal-Wallis (p = 2.925 × 10-8) was found. CONCLUSION: It is clear that the proposed measurement technique is able to identify differences between volumes (operated and contralateral). The clinical monitoring of these patients can validate the results obtained by this measurement technique, and it will serve to estimate the effectiveness of the surgical technique applied in patients.

ANTECEDENTES: El método más utilizado para la evaluación posquirúrgica de la displasia del desarrollo de la cadera inveterada es la radiografía convencional, lo que impide medir con precisión cambios intraarticulares. OBJETIVO: Analizar los cambios morfológicos del volumen acetabular mediante tomografía computarizada en pacientes operados con miotomía de aductor mediano, tenotomía de psoas, reducción abierta de cadera, diafisectomía, osteotomía varizante y desrotadora, y acetabuloplastia tipo Dega. MÉTODO: Se realizó un estudio piloto en el que se analizaron tomografías de seis pacientes del Instituto Nacional de Rehabilitación con displasia inveterada unilateral, por medio de software de diseño para determinar el volumen acetabular. RESULTADOS: Se encontró que el volumen acetabular operado fue mayor que el contralateral (8 vs. 48%), pero no se halló diferencia significativa entre los volúmenes (p = 2.46). Se encontraron diferencias significativas entre los volúmenes y la edad de los pacientes, evaluadas mediante ANOVA multifactorial (p = 0.006), Cochran (p = 2.925 × 10−8) y Kruskal-Wallis (p = 0.00019). CONCLUSIÓN: Es claro que la técnica de medición propuesta permite identificar diferencias entre volúmenes (operado y contralateral). El seguimiento clínico de estos pacientes podrá validar los resultados obtenidos por este método y servirá para poder estimar la eficacia de la técnica quirúrgica aplicada en los pacientes.

Effect of insertion angle on the stability of orthodontic mini-implants in a rabbit tibia model: A finite element analysis.

INTRODUCTION: Mini-implants are an alternative to traditional methods of anchorage in orthodontic treatment. However, there are still questions concerning their application, in particular, with the insertion angle. OBJECTIVE: To determine whether the angle of insertion of the mini-implant is a determining factor in their primary stability when they support orthodontic loads. MATERIALS AND METHODS: A finite element model (FEM) of tibia bone, spring and mini-implant was developed. The three-dimensional model of the rabbit tibia was constructed based on tomographic slices. The angles that were analyzed were 90°, 80°, 70°, 60°, 50°, 45°, 40°, and 30°. A horizontal force of 2 N applied to the head of the mini-implants was simulated. The von Mises stresses and displacements were determined using FEM. RESULTS: Von Mises stresses were lower for an insertion angle of 40° followed by 90° and 70°; likewise, the displacements of the mini-implants with respect to the spring were lower for the 40° angle followed by 90° and 70°, we found a statistically significant association between the insertion angle and displacement. CONCLUSION: All mini-implants underwent a degree of angulation and displacement; however, mini-implants inserted to the bone surface at 40° tend to have better primary stability, and they can withstand loads immediately.

INTRODUCCIÓN: Los miniimplantes son una alternativa para los métodos de anclaje tradicionales en el tratamiento de ortodoncia. Sin embargo, existen interrogantes referentes a su uso, en particular en cuanto al ángulo de inserción. OBJETIVO: ­Determinar si el ángulo de inserción es un factor determinante en la estabilidad primaria de los miniimplantes cuando soportan cargas. MÉTODO: Se desarrolló un modelo tridimensional de elementos finitos del conjunto tibia, miniimplante y resorte a partir de cortes tomográficos; finalmente, el resorte fue modelado empleando elementos de contacto. Las angulaciones analizadas fueron 90°, 80°, 70°, 60°, 50°, 45°, 40° y 30°. Una fuerza de 2 N fue aplicada a los implantes. Se determinaron los esfuerzos de von Mises y los desplazamientos empleando elementos finitos. RESULTADOS: Los esfuerzos de von Mises fueron menores para un ángulo de inserción de 40°, seguido por los de 90° y 70°; de igual forma, los desplazamientos en los miniimplantes con respecto al resorte fueron menores para un ángulo de 40°, seguido por los de 90° y 70°. CONCLUSIÓN: Todos los miniimplantes presentaron un cierto grado de angulación y desplazamiento, pero los ­insertados en la superficie ósea a 40° tienden a presentar mejor estabilidad primaria y pueden ser inmediatamente sometidos a carga.

Effect of ascorbic acid and epidermal growth factor in a rat tibia defect

Purpose: Bone repair aims to restore the anatomical, biomechanical, and functional integrity of the affected structure. Here we study the effects of ascorbic acid (AA) and epidermal growth factor (EGF) applied in a single dose and in combination on the repair of a noncritical bone defect model. Methods: Twenty-four rats were divided into four groups: an intact G-1 control group, and three groups that underwent a noncritical bone defect in the right tibia: G-2 treated with AA, G-3 treated with EGF, and G-4 treated with AA in combination with EGF. After 21 days of treatment, rats were sacrificed, the tibias were dissected and a destructive biomechanical analysis of three-point flexion test was performed in a universal testing machine; the values of stiffness, resistance, maximum energy, and energy at maximum load were statistically compared. Results: G-3 and G-4 recovered the biomechanical properties of strength and stiffness of an intact tibia 3 weeks after their application. Not so the energy and energy at maximum load. For G-2, only the stiffness of an intact tibia was recovered. Conclusion: EGF and AA-EGF applied to a noncritical bone defect in the rat tibia favors the recovery of bone resistance and stiffness.

Treatment of cosmetic wastewater by a full-scale membrane bioreactor (MBR).

This work evaluates the treatment of wastewater from a personal care products factory by a full-scale side-stream membrane bioreactor (MBR) intermittently fed. The wastewater contained particulate and soluble chemical oxygen demand (COD) which is partially removed by physicochemical pretreatment. Steady removal efficiencies above 98 % were achieved for BOD5, COD and suspended solids. Fats, oils and grease present in the raw wastewater were also successfully removed. The MBR was operated at an average permeate flux of 12 L/m2 · h (LMH) working at a transmembrane pressure of 272 ± 97 mbar. The soluble microbial products concentration remained fairly stable at 175 ± 25 and 85 ± 15 mg/L for proteins and carbohydrates, respectively. This maintained the filtration characteristics of the mixed liquor unaltered over a long-term basis, which was evidenced by a constant permeability of 43 ± 19 LMH/bar. Most of the trace organics detected in the wastewater were completely removed and only some fragrances were detected in the permeate at trace concentrations.

Removal of trace organics by anaerobic membrane bioreactors.

The biological removal of 38 trace organics (pharmaceuticals, endocrine disruptors, personal care products and pesticides) was studied in an anaerobic membrane bioreactor (AnMBR). This work presents complete information on the different removal mechanisms involved in the removal of trace organics in this process. In particular, it is focused on advanced characterization of the relative amount of TO accumulated within the fouling layers formed on the membranes. The results show that only 9 out of 38 compounds were removed by more than 90% while 23 compounds were removed by less than 50%. These compounds are therefore removed in an AnMBR biologically and partially adsorbed and retained by flocs and the deposition developed on the membranes, respectively. A total amount of 288 mg of trace organics was retained per m(2) of membrane, which were distributed along the different fouling layers. Among the trace organics analyzed, 17α-ethynylestradiol, estrone, octylphenol and bisphenol A were the most retained by the fouling layers. Among the fouling layers deposited on the membranes, the non-readily detachable layer has been identified as the main barrier for trace organics.

Análisis del comportamiento mecánico del tejido subyacente a las tuberosidades isquiáticas por medio del método del elemento finito / Analysis of mechanical behavior of the underlying tissue to the ischial tuberosities using finite element method

Las úlceras por presión son las complicaciones secundarias más comunes a una lesión medular, las cuales ponen en riesgo tanto la salud como la vida de quienes las padecen. Las úlceras por presión más comunes en lesionados medulares aparecen en la región pélvica, principalmente en las tuberosidades isquiáticas (TI's). Una estrategia usada en la clínica es medir la presión generada entre el paciente y la superficie donde se encuentra para evaluar el riesgo que representa dicha superficie para el desarrollo de úlceras por presión sin embargo, este tipo de mediciones superficiales no garantizan que la presión en los tejidos internos subyacentes a prominencias óseas sea inocua. Con el fin de estudiar los mecanismos de formación de úlceras por presión, se realizó el análisis de un modelo de pelvis y tejido subyacente por medio del Método de los Elementos Finitos (MEF). De esta manera se puede estudiar el comportamiento de las TI's sobre su tejido circundante, así como analizar los efectos biomecánicos que provocan las úlceras. Se construyó el modelo computacional por medio de un software de CAD (Computing Aided Design) de la pelvis a partir de cortes tomográficos. El modelo fue exportado al software COMSOL y se analizaron seis casos de estudio: un análisis de la pelvis sobre bloques de tejido sano y cinco casos más, los cuales simulan lesiones en el tejido con distintas profundidades, representando úlceras superficiales e internas. Los resultados mostraron que los puntos de máximo esfuerzo, en todas las pruebas, se localizan justo debajo de la TIs además se encontró que las lesiones internas presentan mayores esfuerzos y deformaciones, los cuales pueden ser precursores de daño en el tejido.

Pressure ulcers are the most common secondary complication to a spinal cord injury, which endanger both health and life of the patients who suffer them. The most common pressure ulcers in spinal cord injuries occur in the pelvic region, mainly in the ischial tuberosities (ITs). A strategy used in clinic is to quantify the pressure generated between the patient and the surface, in order to assess the risk posed by that surface for developing pressure ulcers. Despite this, this type of surface measurements does not guarantee that pressure in the internal tissues underlying to bony prominences, to be safe. In order to study the mechanisms of formation of pressure ulcers, an analysis of a model of the pelvis and its underlying tissue was performed using the Finite Element Method (FEM). By this means we can study the behavior of ITs on its surrounding tissue, and at the same time, we analyze the biomechanical effects those cause ulcers. The computational model of the pelvis was built from tomographic slices using CAD software (Computing Aided Design). The model was exported to the finite element software COMSOL and six study cases were analyzed: an analysis of the pelvis on healthy tissue blocks and five more cases, which simulate tissue injury with different depths, representing surface and internal ulcers. The results showed that the maximum stress points in all tests are located just below the ITs it was also found that internal injuries present higher stresses and strains, which can be precursors of tissue damage.