RESUMO
Pathogenic bacteria in drinking-water pose a health risk to consumers, as they compromise the quality of portable water. Chemical disinfection of water containing dissolved organic matter (DOM) causes harmful disinfection by-products. In this work, 4-hydroxybenzoic acid (4-HBA) blended polyethersulfone membranes were fabricated and characterised using microscopic and spectroscopic techniques. The membranes were evaluated for the removal of bacteria and DOM from synthetic and environmental water. Permeate flux increased from 287.30 to 374.60 l m-2 h-1 at 3 bars when 4-HBA increased from 0 to 1.5 wt.%, suggesting that 4-HBA influenced the membrane's affinity for water. Furthermore, 4-HBA demonstrated antimicrobial properties by inhibiting bacterial growth. The membrane with 1 wt.% 4-HBA recorded 99.4 and 100% bacteria removal in synthetic and environmental water, respectively. Additionally, DOM removal of 55-73% was achieved. A flux recovery ratio (FRR) of 94.6% was obtained when a mixture of bacteria and humic acid was filtered, implying better fouling layer reversibility during cleaning. Furthermore, 100% FRR was achieved when a multimedia granular filtration step was installed prior to membrane filtration. The results illustrated that the membranes had a high permeate flux with low irreversible fouling. This indicated the potential of the membranes in treating complex feed streams using simple cleaning protocols.
Assuntos
Bactérias , Biofilmes , Incrustação Biológica , Água Doce , Membranas Artificiais , Purificação da Água , Biofilmes/efeitos dos fármacos , Biofilmes/crescimento & desenvolvimento , Incrustação Biológica/prevenção & controle , Purificação da Água/métodos , Água Doce/microbiologia , Bactérias/efeitos dos fármacos , Substâncias Húmicas/análise , Filtração/métodos , Parabenos/química , Sulfonas/química , Polímeros/químicaRESUMO
Marine molluscs are of enormous scientific interest due to their astonishing diversity in terms of their size, shape, habitat, behaviour, and ecological roles. The phylum Mollusca is the second most common animal phylum, with 100,000 to 200,000 species, and marine molluscs are among the most notable class of marine organisms. This work aimed to show the importance of marine molluscs as a potential source of nutraceuticals as well as natural medicinal drugs. In this review, the main classes of marine molluscs, their chemical ecology, and the different techniques used for the extraction of bioactive compounds have been presented. We pointed out their nutraceutical importance such as their proteins, peptides, polysaccharides, lipids, polyphenolic compounds pigments, marine enzymes, minerals, and vitamins. Their pharmacological activities include antimicrobial, anticancer, antioxidant, anti-inflammatory, and analgesic activities. Moreover, certain molluscs like abalones and mussels contain unique compounds with potential medicinal applications, ranging from wound healing to anti-cancer effects. Understanding the nutritional and therapeutic value of marine molluscs highlights their significance in both pharmaceutical and dietary realms, paving the way for further research and utilization in human health.
Assuntos
Organismos Aquáticos , Suplementos Nutricionais , Moluscos , Animais , Moluscos/química , Humanos , Produtos Biológicos/farmacologia , Produtos Biológicos/químicaRESUMO
Inhabitants of extreme and polluted environments are attractive as candidates for environmental bioremediation. Bacteria growing in oil refinery effluents, tannery dumpsite soils, car wash effluents, salt pans and hot springs were screened for microcystin-LR biodegradation potentials. Using a colorimetric BIOLOG MT2 assay; Arthrobacter sp. B105, Arthrobacter junii, Plantibacter sp. PDD-56b-14, Acinetobacter sp. DUT-2, Salinivibrio sp. YH4, Bacillus sp., Bacillus thuringiensis and Lysinibacillus boronitolerans could grow in the presence of microcystin-LR at 1, 10 and 100 µg L-1. Most bacteria grew optimally at 10 µg L-1 microcystin-LR under alkaline pH (8 and 9). The ability of these bacteria to use MC-LR as a growth substrate depicts their ability to metabolize the toxin, which is equivalent to its degradation. Through PCR screening, these bacteria were shown to lack the mlr genes implying possible use of a unique microcystin-LR degradation pathway. The study highlights the wide environmental and taxonomic distribution of microcystin-LR degraders.
Assuntos
Actinomycetales , Bactérias , Bactérias/genética , Bactérias/metabolismo , Toxinas Marinhas , Microcistinas/metabolismo , Actinomycetales/metabolismo , Biodegradação AmbientalRESUMO
In this study, functionalized mesoporous silica was prepared and characterized as a stationary phase using various analytical and solid-state techniques, including a Fourier-transform infrared (FTIR) spectrometer, thermogravimetric analysis, and nitrogen sorption. The results confirmed the successful synthesis of the hybrid stationary phase. The potential of the prepared hybrid mesoporous silica as a solid-phase extraction (SPE) stationary phase for separating and enriching polycyclic aromatic hydrocarbons (PAHs) in both spiked water samples and real water samples was evaluated. The analysis involved extracting the PAHs from the water samples using solid-phase extraction and analyzing the extracts using a two-dimensional gas chromatograph coupled to a time-of-flight mass spectrometer (GC × GC-TOFMS). The synthesized sorbent exhibited outstanding performance in extracting PAHs from both spiked water samples and real water samples. In the spiked water samples, the recoveries of the PAHs ranged from 79.87% to 95.67%, with relative standard deviations (RSDs) ranging from 1.85% to 8.83%. The limits of detection (LOD) for the PAHs were in the range of 0.03 µg/L to 0.04 µg/L, while the limits of quantification (LOQ) ranged from 0.05 µg/L to 3.14 µg/L. Furthermore, all the calibration curves showed linearity, with correlation coefficients (r) above 0.98. Additionally, the results from real water samples indicated that the levels of individual PAH detected ranged from 0.57 to 12.31 µg/L with a total of 44.67 µg/L. These findings demonstrate the effectiveness of the hybrid mesoporous silica as a promising stationary phase for solid-phase extraction and sensitive detection of PAHs in water samples.
RESUMO
Freshwater resources play a pivotal role in sustaining life and meeting various domestic, agricultural, economic, and industrial demands. As such, there is a significant need to monitor the water quality of these resources. Water quality index (WQI) models have gradually gained popularity since their maiden introduction in the 1960s for evaluating and classifying the water quality of aquatic ecosystems. WQIs transform complex water quality data into a single dimensionless number to enable accessible communication of the water quality status of water resource ecosystems. To screen relevant articles, the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) method was employed to include or exclude articles. A total of 17 peer-reviewed articles were used in the final paper synthesis. Among the reviewed WQIs, only the Canadian Council for Ministers of the Environment (CCME) index, Irish water quality index (IEWQI) and Hahn index were used to assess both lotic and lentic ecosystems. Furthermore, the CCME index is the only exception from rigidity because it does not specify parameters to select. Except for the West-Java WQI and the IEWQI, none of the reviewed WQI performed sensitivity and uncertainty analysis to improve the acceptability and reliability of the WQI. It has been proven that all stages of WQI development have a level of uncertainty which can be determined using statistical and machine learning tools. Extreme gradient boosting (XGB) has been reported as an effective machine learning tool to deal with uncertainties during parameter selection, the establishment of parameter weights, and determining accurate classification schemes. Considering the IEWQI model architecture and its effectiveness in coastal and transitional waters, this review recommends that future research in lotic or lentic ecosystems focus on addressing the underlying uncertainty issues associated with the WQI model in addition to the use of machine learning techniques to improve the predictive accuracy and robustness and increase the domain of application.
Assuntos
Monitoramento Ambiental , Qualidade da Água , Monitoramento Ambiental/métodos , Ecossistema , Reprodutibilidade dos Testes , CanadáRESUMO
This work investigates the enhancement of antifouling properties of ceramic nanofiltration membranes by surface modification via atomic layer deposition (ALD) of TiO2. Feed solutions containing bovine serum albumin (BSA), humic acid (HA) and sodium alginate (SA) were used as model foulants. The classic fouling mechanism models and the modified fouling indices (MFI) were deduced from the flux decline profiles. Surface roughness values of the ALD coated and uncoated membranes were 63 and 71 nm, respectively, while the contact angles were 34.2 and 59.5°, respectively. Thus, coating increased the water affinity of the membrane surfaces and consequently improved the anti-fouling properties. The MFI values and the classic fouling mechanism correlation coefficients for cake filtration for the ALD coated and the uncoated membrane upon SA fouling were 42,963 (R2 = 0.82) and 143,365 sL-2 (R2 = 0.98), respectively, whereas the correlation coefficients for the combined foulants (SA + BSA + HA) were 267,185 (R2 = 0.99) and 9569 sL-2 (R2 = 0.37), respectively. The study showed that ALD can effectively enhance the antifouling properties of ceramic membranes.
Assuntos
Incrustação Biológica , Purificação da Água , Alginatos , Biofilmes , Incrustação Biológica/prevenção & controle , Cerâmica , Substâncias Húmicas/análise , Membranas Artificiais , Soroalbumina BovinaRESUMO
Energy and environmental challenges are global concerns that scientists are interested in alleviating. It is on this premise that we prepared boron/nitrogen graphene-coated Cu0/TiO2 (B/N-graphene-coated Cu/TiO2) photocatalyst of varying B:N ratios with dual functionality of H2 production and 2-Chlorophenol (2-CP) degradation. In-situ coating of Cu0 with B/N-graphene is achieved via solvothermal synthesis and calcination under an inert atmosphere. All B/N-graphene-coated Cu/TiO2 exhibit higher photonic efficiencies (5.68%-7.06% at 300 < λ < 400 nm) towards H2 production than bare TiO2 (0.25% at 300 < λ < 400 nm). Varying the B:N ratio in graphene influences the efficiency of H2 generation. A B:N ratio of 0.08 yields the most active composite exhibiting a photonic efficiency of 7.06% towards H2 evolution and a degradation rate of 4.07 × 10-2 min-1 towards 2-chlorophenol (2-CP). Density functional theory (DFT) investigations determine that B-doping (p-type) enhances graphene stability on Cu0 while N-doping (n-type) increases the reduction potential of Cu0 relative to H+ reduction potential. X-ray photoelectron spectroscopy reveals that increasing the B:N ratio increases p-type BC2O while decreasing n-type pyridinic-N in graphene thus altering the interlayer electron density. Isotopic labelling experiments determine water reduction as the main mechanism by which H2 is produced over B/N-graphene-coated Cu/TiO2. The reactive species involved in the degradation of 2-CP are holes (h+), hydroxyl radical (OHâ¢), and O2â¢-, of which superoxide (O2â¢-) plays the major role. This work displays B/N -graphene-coated Cu/TiO2 as a potential photocatalyst for large-scale H2 production and 2-CP degradation.
RESUMO
Oil refinery effluents are among stressful environments, and they are characterized by alkaline pH, high concentrations of dissolved solids, electrical conductivity, and metals (mainly Fe, Al, B, Sr, Mn, Cu, Ni). In this study, bacterial diversity in these habitats was inferred from full-length 16S rRNA gene sequences obtained from the PacBio® sequencing platform. The results have shown low bacterial diversity in both raw and treated effluents, with sequences representing only two phyla: Firmicutes and Proteobacteria. Sequences from the raw effluents represent four major genera: Bacillus, Wenzhouxiangella, Rhodabaculum, and Halomonas. Whilst bacterial communities from the treated effluents are relatively more diverse as sequences represent five dominant genera: Pseudoxanthomonas, Brevundimonas, Pseudomonas, Rhodobaculum and Rhizobium. Most of the genera represented in the dataset are halophilic or halotolerant microbes known to have the competency to catabolize a broad spectrum of organic and inorganic pollutants. Hypothetically, these bacteria may be relevant for biotechnological and industrial applications, particularly for the remediation of saline industrial wastes.
Assuntos
Bactérias/classificação , Bactérias/genética , Biodiversidade , Resíduos Industriais , Indústria de Petróleo e Gás , Microbiologia Ambiental , RNA Ribossômico 16S/genéticaRESUMO
Kigelia africana plant is widely used as a herbal remedy in preventing the onset and the treatment of cancer-related infections. With the increase in the research interest of the plant, the specific chemical compound or metabolite that confers its anticancer properties has not been adequately investigated. The ethyl acetate and butanol fractions of the fruit extracts were evaluated by 2-(4,5-dimethylthiazol-2-yl)-3,5-diphenyl-2H-tetrazolium bromide assay against four different cell lines, with the ethyl acetate fraction having inhibition concentration values of 0.53 and 0.42 µM against Hep G2 and HeLa cells, respectively. More than 235 phytoconstituents were profiled using UHPLC-TOF-MS, while more than 15 chemical compounds were identified using GC-MS from the fractions. Molecular docking studies revealed that physostigmine, fluazifop, dexamethasone, sulfisomidine, and desmethylmirtazapine could favorably bind at higher binding energies of -8.3, -8.6, -8.2, and -8.1 kcal/mol, respectively, better than camptothecin with a binding energy of -7.9 kcal/mol. The results of this study showed that physostigmine interacted well with topoisomerase IIα and had a high score of pharmacokinetic prediction using absorption, distribution, metabolism, excretion, and toxicity profiles, thereby suggesting that drug design using physostigmine as a base structure could serve as an alternative against the toxic side effects of doxorubicin and camptothecin.
Assuntos
Antineoplásicos Fitogênicos , Bignoniaceae/química , Metaboloma/efeitos dos fármacos , Metabolômica/métodos , Fisostigmina , Proliferação de Células/efeitos dos fármacos , Sobrevivência Celular/efeitos dos fármacos , Cromatografia Líquida de Alta Pressão , Frutas/química , Cromatografia Gasosa-Espectrometria de Massas/métodos , Células HeLa , Células Hep G2 , Humanos , Simulação de Acoplamento Molecular , Extratos Vegetais/químicaRESUMO
Wastewater treatment plants (WWTPs) in South Africa, like is the case for most WWTPs around the globe albeit capable of removing substantial quantities of microplastics (MPs) and in fact, the treatments become ineffective for those plastic particles less than 100 µm. As a consequence, the receiving water bodies in which the final effluent is discharged becomes highly polluted. The present research is devoted to the analysis of the pervasive MPs in wastewaters of the treatment plant located in the Gauteng Province, South Africa using Pyrolysis - GC-TOF-MS. Based on the results, there were 23 pyrolyzate products with contributions from PVC, PA, PET and PE with abundances of 47.8%, 13.1%, 17.4% and 4.3% respectively. The remaining 17.4% could be attributed as additives in MPs. The SEM images illustrated that the MPs appeared to be inter - wined, fibrous of different thicknesses and lengths. The highly weathered MPs exhibited the rough surface which was noticeably damaged with peeled off layers presumably because of photo-oxidation during the aging process. The vibrational modes of FTIR revealed the presence of the various functional groups in the corresponding polymers of MPs. The thermal studies confirmed the presence of calcium, aluminum and silicon as residues of catalysts or flame retardants or UV stabilizers in MPs or as adsorbates resulting from the surface adsorption from the surroundings. The Py-GC-TOF-MS confirmed the identity of the various fragments related to the MPs monomers.
Assuntos
Poluentes Químicos da Água , Purificação da Água , Microplásticos , Plásticos , África do Sul , Poluentes Químicos da Água/análiseRESUMO
Objectives: Poor mental health remains a serious public concern worldwide. The most vulnerable individuals are children and adolescents in developing countries. Nutritional deficiency of long-chain omega-3 fatty acids, particularly docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA), have long been recognized as a major contributing factor for mental health illnesses. Provision of ready-to-use natural product rich in preformed Omega-3 DHA and EPA could address this problem. However, most commonly used products are expensive and contain less or no preformed Omega-3 DHA and EPA, making them less suitable for prevention of mental illnesses in resource-poor countries. The main objective of this study was to develop a natural product rich in preformed Omega-3 DHA and EPA from locally available ingredients.Methods: Linear programing (LP) was used to formulate a natural product rich in preformed Omega-3 DHA and other essential nutrients using locally available ingredients other than fish and dairy products. Laboratory analysis was then performed to validate the nutritional value of the LP-formulation using standard analytical methods. The relative difference between the LP tool calculated values, and the laboratory-analyzed values were calculated. Sensory testing was also done to evaluate consumer acceptance of the final product.Results: Optimal formulation contained about 220 mg of preformed Omega-3 DHA + EPA, enough to meet the RDI for children aged 2-10 years. The LP analysis further showed that the cost of the developed product is USD 0.15/100 g, which is 50% lower than that of Plumpy'nut. Laboratory analysis revealed similar results as that of LP at P = 0.05.Conclusions: These findings indicate that ready-to-use natural food rich in preformed DHA and EPA can be developed from locally available ingredients.
Assuntos
Ácidos Docosa-Hexaenoicos/administração & dosagem , Ácidos Graxos Ômega-3/administração & dosagem , Ingredientes de Alimentos , Alimentos Formulados , Transtornos Mentais/prevenção & controle , Preparações de Plantas/administração & dosagem , Programação Linear , Cucurbita , Frutas , Humanos , Saúde Mental , Microalgas , Valor Nutritivo , Sementes , Sesamum , TanzâniaRESUMO
The last decade has witnessed growth in scientific interest towards studying the biodiversity and ecology in extreme environments. Acid Mine Drainage (AMD), formed through the bio-oxidation of metal sulphides, is a typical extreme environment that is inhospitable to most life forms. Through the application of traditional culture-based molecular techniques, it has been established that AMD is home to a low diversity, specialized and novel microbial community that plays a critical role in its formation. Intensive efforts have been channeled towards understanding the ecology, microbial biodiversity, processes and metabolic networks within these simple ecosystems. Molecular techniques using high-throughput next-generation sequencing platforms have taken center stage in discerning both the taxonomic and functional diversity in these microbial communities. Recently developed post-genomic approaches as well have been particularly instrumental in deciphering in situ interactions within microbial communities and the environment. In this review, a critical synopsis of the current applications of advanced molecular techniques in probing microbial and functional diversity in AMD environments is presented.
Assuntos
Ácidos , Ecossistema , Variação Genética , Microbiota , Mineração , Ecologia , Genoma Bacteriano , Genômica , Sequenciamento de Nucleotídeos em Larga EscalaRESUMO
The occurrence of azole antifungals in the environment presents one of the emerging concerns due to their ecotoxicological threat as well as their potential contribution to the evolution of drug resistant fungi in the environment. In this study, the occurrence of eight commonly prescribed azole antifungal drugs was seasonally determined in influent and effluent water samples from three wastewater treatment plants and a drinking water treatment plant in South Africa. In addition, the risk quotient (RQ) method was employed to investigate the potential ecological and human health risks associated with their presence in the wastewater and/or drinking water. Clotrimazole, econazole, fluconazole, itraconazole, ketoconazole and miconazole were detected at least once in the water samples, while posaconazole and voriconazole were not detected in any of the samples for all seasons at which the samples were collected. Fluconazole was detected at higher frequency (about 96%) with a concentration up to 9959.0â¯ngâ¯L-1. Clotrimazole had the second highest frequency of detection (about 33%) with a concentration up to 143.3â¯ngâ¯L-1. Statistically significant temporal variation in clotrimazole (pâ¯<â¯0.05) and spatial variation in fluconazole (pâ¯<â¯0.05) were observed. In general, the preliminary ecological risk assessment based on risk quotient (RQ) calculation indicated that there is currently no high risk against aquatic organisms (Algae, Daphnia and Fish) related to the azole antifungals. Meanwhile, human health risk assessment demonstrated that fluconazole represented high risk in drinking water. Furthermore, risk estimates showed a potential for the detected concentrations of fluconazole and itraconazole in water samples to pose moderate to high risk for development of antifungal drug resistance. Some of the azole antifungal drugs are ubiquitous in the wastewater and future monitoring and validation studies should be conducted for those drugs that seem to pose human health and ecological risks.
Assuntos
Antifúngicos/análise , Azóis/análise , Água Potável/química , Monitoramento Ambiental/métodos , Águas Residuárias/química , Poluentes Químicos da Água/análise , Antifúngicos/toxicidade , Organismos Aquáticos/efeitos dos fármacos , Azóis/toxicidade , Farmacorresistência Fúngica , Ecotoxicologia , Humanos , Medição de Risco , África do Sul , Poluentes Químicos da Água/toxicidadeRESUMO
Graphitic carbon nitride (g-C3N4) is a two-dimensional conjugated polymer that has attracted the interest of researchers and industrial communities owing to its outstanding analytical merits such as low-cost synthesis, high stability, unique electronic properties, catalytic ability, high quantum yield, nontoxicity, metal-free, low bandgap energy, and electron-rich properties. Notably, graphitic carbon nitride (g-C3N4) is the most stable allotrope of carbon nitrides. It has been explored in various analytical fields due to its excellent biocompatibility properties, including ease of surface functionalization and hydrogen-bonding. Graphitic carbon nitride (g-C3N4) acts as a nanomediator and serves as an immobilization layer to detect various biomolecules. Numerous reports have been presented in the literature on applying graphitic carbon nitride (g-C3N4) for the construction of electrochemical sensors and biosensors. Different electrochemical techniques such as cyclic voltammetry, electrochemiluminescence, electrochemical impedance spectroscopy, square wave anodic stripping voltammetry, and amperometry techniques have been extensively used for the detection of biologic molecules and heavy metals, with high sensitivity and good selectivity. For this reason, the leading drive of this review is to stress the importance of employing graphitic carbon nitride (g-C3N4) for the fabrication of electrochemical sensors and biosensors.
Assuntos
Grafite , Nanoestruturas , Compostos de Nitrogênio , CatáliseRESUMO
Iron (Fe), zirconium (Zr) and titanium (Ti) oxides nanoparticles were each embedded onto a weak acid chelating resin for support using the precipitation method to generate three hybrid adsorbents of hydrated Fe oxide (HFO-P), hydrated Zr oxide (HZO-P) and hydrated Ti oxide (HTO-P). This paper reports on the characterization, performance and potential of these generated nanoadsorbents in the removal of toxic metal ions from acid mine drainage (AMD). The optimum contact time, adsorbent dose and pH for aluminium (Al) (III) adsorption were established using the batch equilibrium technique. The metal levels were measured using inductively coupled plasma-optical emission spectrometry. The scanning electron microscopy-energy dispersive X-ray spectroscopy results confirmed the presence of the metal oxides within the hybrid resin beads. HFO-P, HZO-P and HTO-P adsorbed Al(III) rapidly from synthetic water with maximum adsorption capacities of 54.04, 58.36 and 40.10 mg/g, respectively, at initial pH 1.80 ± 0.02. The adsorption of Al(III) is of the second-order in nature (R2 > 0.98). The nanosorbents removed ten selected metals from environmental AMD and the metal removal efficiency was in the order HTO-P > HZO-P > HFO-P. All three hybrid nanosorbents can be used to remove metals from AMD; the choice would be dependent on the pH of the water to be treated.
Assuntos
Poluentes Químicos da Água/análise , Purificação da Água , Adsorção , Concentração de Íons de Hidrogênio , Cinética , MineraçãoRESUMO
The use and abuse of prescription and illicit drugs are on the rise worldwide and as a result residue of these drugs and their metabolites are continually being disposed into the environment through sewage system and other means. Therefore, this paper reports on the development of a cost-effective, simple and sensitive approach that involved the fabrication of an electrochemical sensor from exfoliated graphite (EG) and gold nanoparticles (AuNPs) for the detection of selected psychoactive drugs in water. The fabricated electrochemical sensor was characterized using scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDS) to ascertain its surface morphology characteristics and cyclic voltammetry (CV) for ascertaining the redox potential peak. The EG-AuNPs sensor was able to detect cocaine in water with limit of detection (LOD) and limit quantification (LOQ) of 0.82 and 2.74 µg/L, respectively under the pH of 12.25. The sensor was extended on other psychoactive drugs (methylphenidate, amphetamine and heroin) and one metabolite (6-acetylmorphine) to examine its applicability. The drugs were distinctively detected, and thus making EG-AuNPs electrode a possible alternative sensor for electrochemical detection of psychoactive drugs and their metabolites in synthetic and real water samples.
Assuntos
Técnicas Eletroquímicas/instrumentação , Eletrodos , Nanopartículas Metálicas/química , Psicotrópicos/análise , Técnicas Biossensoriais , Cocaína/análise , Técnicas Eletroquímicas/métodos , Ouro/química , Grafite/química , Concentração de Íons de Hidrogênio , Limite de Detecção , Microscopia Eletrônica de Varredura , Espectrometria por Raios X , Poluentes Químicos da Água/análiseRESUMO
This study surveyed physicochemical properties and bacterial community structure of water and sediments from an acid mine drainage (AMD) dam in South Africa. High-throughput sequence analysis revealed low diversity bacterial communities affiliated within 8 dominant phyla; Acidobacteria, Actinobacteria, Chloroflexi, Firmicutes, Nitrospirae, Proteobacteria, Saccharibacteria, and ca. TM6_(Dependentiae). Acidiphilium spp. which are common AMD inhabitants but rarely occur as dominant taxa, were the most abundant in both AMD water and sediments. Other groups making up the community are less common AMD inhabitants; Acidibacillus, Acidibacter, Acidobacterium, Acidothermus, Legionella, Metallibacterium, Mycobacterium, as well as elusive taxa (Saccharibacteria, ca. TM6_(Dependentiae) and ca. JG37-AG-4). Although most of the taxa are shared between sediment and water communities, alpha diversity indices indicate a higher species richness in the sediments. From canonical correspondence analysis, DOC, Mn, Cu, Cr, Al, Fe, Ca were identified as important determinants of community structure in water, compared to DOC, Ca, Cu, Fe, Zn, Mg, K, Mn, Al, sulfates, and nitrates in sediments. Predictive functional profiling recovered genes associated with bacterial growth and those related to survival and adaptation to the harsh environmental conditions. Overall, the study reports on a distinct AMD bacterial community and highlights sediments as microhabitats with higher species richness than water.
Assuntos
Bactérias/genética , Sequenciamento de Nucleotídeos em Larga Escala , Consórcios Microbianos/genética , Mineração , RNA Bacteriano/genética , RNA Ribossômico 16S/genética , Microbiologia da Água , África do SulRESUMO
A passive sampling device, based on molecularly imprinted membranes (MIM), was fabricated and optimised for sampling polychlorinated biphenyls (PCBs) in aquatic ecosystems. The newly-developed passive sampler was subjected to in-situ calibration studies to determine PCB sampling rates under various conditions of water turbulence and temperature. This was carried out by exposing the passive samplers to water spiked with PCBs in a continuous-flow exposure setup. The samplers were preloaded with known concentrations of performance reference compounds (PRCs) prior to exposure. Sampling rates of seven indicator PCBs' congeners (PCBs 28, 52, 101, 118, 138, 153 and 180) ranged between 15.3 and 95.6 L/d for the different environmental conditions investigated. To determine the field suitability, the samplers were preloaded with PRCs and deployed for 10 days at the Roodeplaat and Hartbeespoort Dams, in South Africa. Water samples were taken at the end of the deployment period to compare the spot-and-grab samples to the developed samplers. PCBs 28, 101 and 138 were detected in the samplers deployed at Hartbeespoort Dam. The samplers deployed at the Roodeplaat Dam had quantifiable amounts of PCBs 28, 52, 101, 138 and 180 (0.047-0.828 ng mL-1 d-1). The sampler enhanced the detectability of PCB 52 and PCB 180, which were not detected in water samples. The field suitability trials indicated that the developed sampler could successfully be used for PCB monitoring. The sampler enhanced the detection of PCBs that would otherwise be too low to detect in samples collected through the traditional spot-and-grab sampling technique.
Assuntos
Monitoramento Ambiental/instrumentação , Bifenilos Policlorados/análise , Poluentes Químicos da Água/análise , Calibragem , Monitoramento Ambiental/métodos , África do SulRESUMO
This work reports on the fundamental factors influencing inter-foulant and foulant-membrane interactions during simulated dissolved organic matter removal using ceramic nanofiltration. Fouling tests were performed using sodium alginate (SAL), humic acid (HA) and bovine serum albumin (BSA) as model foulants. Fouling potentials of each foulant and their mixtures were investigated using feed solutions containing fixed concentrations of K+, Na+, Mg2+ and Ca2+ with a total ionic strength of 10 mM. The impact of modification by atomic layer deposition on fouling mitigation was also assessed. The flux decline in the first 100 min for single foulants was 4.16 × 10-2, 2.69 × 10-2 and 1.60 × 10-2 Lm-2 for SAL, HA and BSA, respectively. These results demonstrated that for the single foulants, deposition on the membrane surface in the early stages of filtration was primarily governed by membrane-foulant interactions. Interestingly, cake filtration was the least fouling mechanism in feed solutions composed of BSA and SAL (R2 = 0.519, 0.374 for BSA + SAL and BSA + SAL + HA, respectively) and the most favorable fouling mechanism of feed solution which included HA and SAL (R2 = 0.972). The water contact angle dropped from 58o to 35° after coating, thus improving its anti-fouling properties.
Assuntos
Ultrafiltração , Purificação da Água , Cerâmica , Filtração , Membranas ArtificiaisRESUMO
This paper reports on the preparation and modification of powdered maize tassels with polydiallyldimethylammonium chloride (polyDADMAC). The modified tassel were applied for the removal of phenolic compounds from water, through adsorption. The effect of contact time, sorbent dose, pH of the sample and the adsorption capacity were investigated at fixed temperature (25 °C). The optimum pH was 6.0 and the uptake was more than 90% within the first 10 min of contact. The adsorption prescribed to Langmuir model of monolayer adsorption implying a chemisorption process. The adsorption capacities were found to be 7.09, 8.23, 8.84 and 4.74 mg g(-1) for chlorobenzoic acid, 2,4,6-trichlorophenol, 2,4-dichlorophenol and 1,2-dihyroxybenzene respectively. These were fairly higher than many other reported systems. The removal efficiency was found to be 75, 64, 55 and 40% for Chlorobenzoic acid, 2,4,6-Trichlorophenol, 2,4-dichlorophenol and 1,2-dihyroxybenzene, respectively. This proved that quaternised maize tassels can be used as an efficient adsorbent material for removal of phenolic compounds from water and wastewater.