How does indirect air-cooling influence pulp chamber temperature in different volume teeth and absence/presence of resin-based composite during light curing?

BACKGROUND: Light-curing of materials during restorative dental procedures poses a risk for pulp tissue overheating. Therefore, the aim of this study was to investigate the effect of indirect air-cooling on pulp chamber temperatures during light-curing of varying volume teeth and absence/presence of resin-based composite (RBC) at different exposure time. METHODS: The volume of 11 human teeth was measured by micro computed tomograph. An experimental rig controlled the thermal environment of the teeth and a thermocouple inserted retrograde into the root canal measured temperature changes. Pulp chamber temperature was measured with and without air-cooling on teeth without and with RBC at 15 s, 30 s and 60 s intervals. Generalized estimating equations were used for statistical analysis. RESULTS: The temperature increase with air-cooling (versus no air-cooling) was lower in teeth despite absence/presence of RBC (ß = - 4.26, 95%CI - 5.33 and ß = - 4.47, 95%CI - 5.60, respectively). With air-cooling, the temperature increase in teeth with RBC was lower compared to teeth without RBC (ß = - 0.42, 95%CI -0.79; - 0.05). Higher teeth volume resulted in lower temperature increase with air-cooling than without air-cooling (ß = - 0.04, 95%CI -0.07; - 0.01 and ß = - 0.17, 95%CI -0.30; - 0.05, respectively). CONCLUSIONS: Air-cooling resulted in lower pulp chamber temperature increase. Using air-cooling, the temperature increase was lower in teeth with RBC compared to teeth without RBC. Lower volume teeth resulted in higher temperature increase, thus they seemed to benefit more from air-cooling compared to higher volume teeth. Air-cooling could be an effective tool in controlling pulp temperature increase during light-curing, especially when the tooth volume is small.

Airborne exposure to gaseous and particle-associated organic substances in resin-based dental materials during restorative procedures.

Dental composite dust has been shown to act as a vehicle for methacrylates in vivo/in vitro. The objective of this study was to assess airborne exposure of dental personnel to gaseous and particle-associated organic constituents from resin-based dental materials in a simulated clinic. Sampling of total aerosol fractions and gaseous substances was performed by dental students carrying particle filters and gas sorbents attached to a personal pump during preclinical restorative procedures in phantom models (n = 13). Water from the phantoms was sampled. Organic substances were extracted from the sampled water, particle filters, and gas sorbents. Qualitative and quantitative analyses were performed by gas chromatography-mass spectrometry (GC-MS) and ultra-high-performance liquid chromatography-mass spectrometry (UHPLC-MS). The methacrylates 2-hydroxyethyl methacrylate (HEMA) and triethylene glycol dimethacrylate (TEGDMA) and the additives camphorquinone (CQ), butylated hydroxytoluene (BHT), and ethyl 4-(dimethylamino)benzoate (DMABEE), were quantified in the gas and particle fractions sampled. A positive-control experiment was conducted. No methacrylates were detected in the gas or particle fractions sampled, whereas strong signals for methacrylates were detected in the positive controls, matching the analysis of the uncured material. In addition, TEGDMA and DMABEE were quantified in the sampled water. Airborne exposure to constituents in resin-based dental materials was below the detection limit. However, the extent of exposure is probably dependent on the procedure, preventive measures, and type of materials used.

Dose- and time-dependent effects of triethylene glycol dimethacrylate on the proteome of human THP-1 monocytes.

Triethylene glycol dimethacrylate (TEGDMA) is commonly used in polymer resin-based dental materials. This study investigated the molecular mechanisms of TEGDMA toxicity by identifying its time- and dose-dependent effects on the proteome of human THP-1 monocytes. The effects of different concentrations (0.07-5 mM) and exposure times (0-72 h) of TEGDMA on cell viability, proliferation, and morphology were determined using a real-time viability assay, automated cell counting, and electron microscopy, and laid the fundament for choice of exposure scenarios in the proteomic experiments. Solvents were not used, as TEGDMA is soluble in cell culture medium (determined by photon correlation spectroscopy). Cells were metabolically labeled [using the stable isotope labeled amino acids in cell culture (SILAC) strategy], and exposed to 0, 0.3 or 2.5 mM TEGDMA for 6 or 16 h before liquid chromatography-tandem mass spectrometry (LC-MS/MS) analyses. Regulated proteins were analyzed in the STRING database. Cells exposed to 0.3 mM TEGDMA showed increased viability and time-dependent upregulation of proteins associated with stress/oxidative stress, autophagy, and cytoprotective functions. Cells exposed to 2.5 mM TEGDMA showed diminished viability and a protein expression profile associated with oxidative stress, DNA damage, mitochondrial dysfunction, and cell cycle inhibition. Altered expression of immune genes was observed in both groups. The study provides novel knowledge about TEGDMA toxicity at the proteomic level. Of note, even low doses of TEGDMA induced a substantial cellular response.

Analysis of organic components in resin-modified pulp capping materials: critical considerations.

The purpose of this study was to elucidate the organic composition and eluates of three resin-based pulp-capping materials in relation to their indications and safety data sheets. Uncured samples of Theracal LC, Ultra-Blend Plus, and Calcimol LC were investigated using gas chromatography-mass spectrometry (GC-MS) and ultra-performance liquid chromatography-mass spectrometry (UPLC-MS). Identification/quantification of 7-d leachables of cured samples was performed using GC-MS for 2-hydroxyethyl methacrylate (HEMA), 2-(dimethylamino)ethyl methacrylate (DMAEMA), camphorquinone (CQ), ethylene glycol dimethacrylate (EGDMA), ethyl-4-(dimethylamino)benzoate (DMABEE), and triethylene glycol dimethacrylate (TEGDMA). A similar organic composition was found for Ultra-Blend and Calcimol; however, only Ultra-Blend is indicated for direct pulp-capping. In contrast to the other materials analysed, Theracal contained substances of high molecular weight. The safety data sheets of all materials were incomplete. We detected HEMA, CQ, and TEGDMA in eluates from Ultra-Blend and Calcimol, and it was considered that HEMA might have originated from decomposition of diurethane dimethacrylate (UDMA) in the GC-injector. For Theracal, additives associated with light curing (DMABEE and CQ) were detected in higher amounts (4.11 and 19.95 µg mm-2 ) than in the other materials. Pores were quantified in all samples by micro-computed tomography (micro-CT) analysis, which could influence leaching. The organic substances in the investigated materials might affect their clinical suitability as capping agents, especially for direct capping procedures.

Methods and terminology used in cell-culture studies of low-dose effects of matrix constituents of polymer resin-based dental materials.

General comprehension of terms and confounding factors associated with in vitro experiments can maximize the potential of in vitro testing of substances. In this systematic review, we present an overview of the terms and methods used to determine low-dose effects of matrix constituents in polymer resin-based dental materials in cell-culture studies and discuss the findings in light of how they may influence the comprehension and interpretation of results. Articles published between 1996 and 2015 were identified by searches in the Scopus, Web of Science, MEDLINE, PubMed, and Embase databases using keywords associated with low-dose effects, polymer resin-based materials, in vitro parameters, and dental materials. Twenty-nine articles were included. Subtoxic (n = 11), sublethal (n = 10), and nontoxic (n = 6) were the terms most commonly used to describe the low-dose effects of methacrylates. However, definition of terms varied. Most (82%) studies employed only one method to define the exposure scenario, and no agreement was seen between studies on the use of solvents. Prophylactic use of antibiotics was widespread, and mycoplasma screening was not reported. In conclusion, cell-culture conditions and tests used to define exposure scenarios have changed little in the last decades, despite development in recommendations. Nomenclature alignment is needed for a better understanding of possible biohazards of methacrylates.