Enhancement in Kinetics of the Oxygen Reduction Reaction on a Nitrogen-Doped Carbon Catalyst by Introduction of Iron via Electrochemical Methods.

The iron (Fe) electrodeposition-electrochemical dissolution has been employed on nitrogen-doped carbon material (P-PI) prepared via multi-step pyrolysis of a polyimide precursor to achieve the introduction of Fe species, and its influence on the oxygen reduction reaction (ORR) is investigated by cyclic and rotating ring-disk electrode voltammetry in 0.5 M H2SO4. After the electrochemical treatment, the overpotential and H2O2 production percentage of ORR on the P-PI are decreased and the number of electrons transferred is increased in the meanwhile. In combination with the results of X-ray absorption fine structure spectra, the presence of Fe-Nx sites (Fe ions coordinated by nitrogen) is believed to be responsible for the improved ORR performance. Further kinetic analysis indicates that a two-electron reduction of O2 is predominant on the untreated P-PI with coexistence of a direct four-electron transformation of O2 to H2O, while the introduction of Fe species leads to a larger increase in the rate constant for the four-electron reduction than that for the two-electron process, being in good agreement with the view that Fe-Nx sites are active for four-electron ORR.

Continuous and simultaneous electrochemical measurements of glucose, lactate, and ascorbate in rat brain following brain ischemia.

Developing new tools and technologies to enable recording the dynamic changes of multiple neurochemicals is the essence of better understanding of the molecular basis of brain functions. This study demonstrates a microfluidic chip-based online electrochemical system (OECS) for in vivo continuous and simultaneous monitoring of glucose, lactate, and ascorbate in rat brain. To fabricate the microfluidic chip-based detecting system, a microfluidic chip with patterned channel is developed into an electrochemical flow cell by incorporating the chip with three surface-modified indium-tin oxide (ITO) electrodes as working electrodes, a Ag/AgCl wire as reference electrode, and a stainless steel tube as counter electrode. Selective detection of ascorbate is achieved by the use of single-walled carbon nanotubes (SWNTs) to largely facilitate the electrochemical oxidation of ascorbate, while a dehydrogenase-based biosensing mechanism with methylene green (MG) adsorbed onto SWNTs as an electrocatalyst for the oxidation of dihydronicotiamide adenine dinucleotide (NADH) is employed for biosensing of glucose and lactate. To avoid the crosstalk among three sensors, the sensor alignment is carefully designed with the SWNT-modified electrode in the upstream channel and paralleled glucose and lactate biosensors in the downstream channels. With the microfluidic chip-based electrochemical flow cell as the detector, an OECS is successfully established by directly integrating the microfluidic chip-based electrochemical flow cell with in vivo microdialysis. The OECS exhibits a good linear response toward glucose, lactate, and ascorbate with less crosstalk. This property, along with the high stability and selectivity, enables the OECS for continuously monitoring three species in rat brain following brain ischemia.

Characterization by electrochemical and X-ray photoelectron spectroscopic measurements and quantum chemical calculations of N-containing functional groups introduced onto glassy carbon electrode surfaces by electrooxidation of a carbamate salt in aqueous solutions.

The present paper deals with characterization of an aminated glassy carbon electrode (GCE) surface obtained by electrooxidation of ammonium carbamate in its aqueous solution (amination reaction) using electrochemical and XPS methods. From the XPS analysis, it was found that not only the primary amine group (i.e., aniline-like aromatic amine moiety) but also other N-containing functional groups (i.e., the secondary amine-like moieties containing pyrrole-type nitrogen and quaternary amine-like moieties containing graphitic quaternary nitrogen) are introduced onto the GCE surface during the amination reaction. Moreover, the presence of the primary and secondary amine groups was ascertained based on the difference in the reactivity of a Michael reaction-type addition reaction of amine groups introduced onto the GCE surface with quinone compounds having a carbonyl group and a C═C double bond (i.e., in this case, 1,2-benzoquinone which is in situ prepared by the electrooxidation of catechol) and on the electrochemical redox response of the introduced benzoquinones. This electrochemical treatment of aminated GCE with catechol led to catechol-grafted aminated GCE which indicated two surface redox couples (i.e., the Ia/Ic and IIa/IIc couples with formal potentials of E(0)'(Ia/Ic) = ca. 0.17 V and E(0)'(IIa/IIc) = ca. 0.03 V vs Ag|AgCl|KCl(sat.) in phosphate buffer solution (pH 7)). From the electrochemical behavior of catechols grafted onto the maleimide-treated aminated GCE and on the methylamine-treated GCE, it was found that the catechol associated with the primary amine groups gave the IIa/IIc redox peaks, while the catechol bound to the secondary amine groups gave the Ia/Ic redox peaks. Further electrochemical measurements and quantum chemical calculations concluded that the IIa/IIc redox peaks are ascribed to the surface-redox reaction of the 1,2-dihydroxybenzene/1,2-benzoquinone couple, while those of the 1,2-dihydroxybenzene/1,2-benzoquinone and the N-(4'-hydroxyphenyl)-p-aminophenol/indophenol couples can be associated with the Ia/Ic redox peaks.

Online electrochemical monitoring of dynamic change of hippocampal ascorbate: toward a platform for in vivo evaluation of antioxidant neuroprotective efficiency against cerebral ischemia injury.

Effective monitoring of cerebral ascorbate following intravenous antioxidant treatment is of great importance in evaluating the antioxidant efficiency for neuroprotection because ascorbate is closely related to a series of ischemia-induced neuropathological processes. This study demonstrates the validity of an online electrochemical system (OECS) for ascorbate detection as a platform for in vivo evaluation of neuroprotective efficiency of antioxidants by studying the dynamic change of hippocampal ascorbate during the acute period of cerebral ischemia and its responses to intravenous administration of antioxidants including ascorbate and glutathione (GSH). The OECS consists of a selective electrochemical detector made of a thin-layer electrochemical flow cell integrated with in vivo microdialysis. With such a system, the basal level of hippocampal ascorbate is determined to be 5.18 ± 0.60 µM (n = 20). This level is increased by 10 min of two-vessel occlusion (2-VO) ischemia treatment and reaches 11.51 ± 3.43 µM (n = 5) at the time point of 60 min after the ischemia. The 2-VO ischemia-induced hippocampal ascorbate increase is obviously attenuated by immediate intravenous administration of ascorbate (2.94 g/kg) or glutathione (5.12 g/kg) within 10 min after ischemia and the ascorbate level remains to be 3.75 ± 1.66 µM (n = 4) and 5.30 ± 0.79 µM (n = 5), respectively, at the time point of 60 min after ischemia. To confirm if the attenuated hippocampal ascorbate increase is attributed to the antioxidant-induced oxidative stress alleviation, we further study the immunoreactivity of 8-hydroxy-2-deoxyguanosine (8-OHdG) in the ischemic hippocampus and find that the 8-OHdG immunoreactivity is decreased by the administration of ascorbate or GSH as compared to the ischemic brain without antioxidant treatment. These results substantially demonstrate that the OECS for ascorbate detection could be potentially used as a platform for evaluating the efficiency of antioxidant neuroprotection in cerebral ischemia treatment.

Microfluidic chip-based online electrochemical detecting system for continuous and simultaneous monitoring of ascorbate and Mg2+ in rat brain.

This study demonstrates a microfluidic chip-based online electrochemical detecting system for in vivo continuous and simultaneous monitoring of ascorbate and Mg(2+) in rat brain. In this system, a microfluidic chip is used as the detector for both species. To fabricate the detector, a single-channel microfluidic chip is developed into an electrochemical flow cell by incorporating the chip with an indium-tin oxide (ITO) electrode as working electrode, an Ag/AgCl wire as reference electrode, and a stainless steel tube as counter electrode. Selective detection of ascorbate and Mg(2+) is achieved by drop-coating single-walled carbon nanotubes (SWNTs) and polymerizing toluidine blue O (polyTBO) film onto the ITO electrode, respectively. Moreover, the alignment of SWNT-modified and polyTBO-modified electrodes and the solution introduction pattern are carefully designed to avoid any cross talk between two electrodes. With the microfluidic chip-based electrochemical flow cell as the detector, an online electrochemical detecting system is successfully established by directly integrating the microfluidic chip-based electrochemical flow cell with in vivo microdialysis. The microfluidic system exhibits sensing properties with a linear relationship from 5 to 100 µM for ascorbate and from 100 to 2000 µM for Mg(2+). Moreover, this system demonstrates a high selectivity and stability and good reproducibility for simultaneous measurements of ascorbate and Mg(2+) in a continuous-flow system. These excellent properties substantially render this system great potential for continuous and simultaneous online monitoring of ascorbate and Mg(2+) in rat brain.

Electroless deposition of platinum nanoparticles in room-temperature ionic liquids.

The electroless deposition of Pt nanoparticles (Pt-NPs) could be carried out by dissolving potassium tetrachloroplatinate(II) (K2[PtCl4]) in 1-ethyl-3-methylimidazolium (EMI(+)) room-temperature ionic liquids (RTILs) containing bis(trifluoromethylsulfonyl) imide (NTf2(-)) or tetrafluoroborate (BF4(-)) anion and small cations, such as H(+), K(+), and Li(+). In this case, no deposition of Pt-NPs occurred in RTILs without such small cations. The formation of Pt-NPs was only observed in RTILs containing trifluoromethanesulfonimide (HNTf2) and protons at high temperature (≥80 °C) when potassium hexachloroplatinate(IV) (K2[PtCl6]) was dissolved in the RTILs. The obtained Pt-NPs gave a characteristic absorption spectrum of ultrasmall Pt-NPs. The ultrasmall and uniform Pt-NPs of ca. 1-4 nm in diameter were produced and the Pt-NPs/EMI(+)NTf2(-) dispersion was kept stably for several months without adding any additional stabilizers or capping molecules. The identified Fourier-transform patterns along the [0 1 1] zone axis were observed for the TEM images of Pt-NPs. On the basis of the results obtained, a probable mechanism of the electroless formation of Pt-NPs is discussed.

Biofuel cell-based self-powered biogenerators for online continuous monitoring of neurochemicals in rat brain.

This study demonstrates a new electrochemical method for continuous neurochemical sensing with a biofuel cell-based self-powered biogenerator as the detector for the analysis of microdialysate continuously sampled from rat brain, with glucose as an example analyte. To assemble a glucose/O(2) biofuel cell that can be used as a self-powered biogenerator for glucose sensing, glucose dehydrogenase (GDH) was used as the bioanodic catalyst for the oxidation of glucose with methylene green (MG) adsorbed onto single-walled carbon nanotubes (SWNTs) as the electrocatalyst for the oxidation of dihydronicotinamide adenine dinucleotide (NADH). Laccase crosslinked onto SWNTs was used as the biocathodic catalyst for the O(2) reduction. To enable the bioanode and biocathode to work efficiently in their individually favorable solutions and to eliminate the interference between the glucose bioanode and O(2) biocathode, the biofuel cell-based biogenerator was built in a co-laminar microfluidic chip so that the bioanodic and biocathodic streams could be independently optimized to provide conditions favorable for each of the bioelectrodes. By using a home-made portable voltmeter to output the voltage generated on an external resistor, the biogenerator was used for glucose sensing based on a galvanic cell mechanism. In vitro experiments demonstrate that, under the optimized conditions, the voltage generated on an external resistor shows a linear relationship with the logarithmic glucose concentration within a concentration range of 0.2 mM to 1.0 mM. Moreover, the biogenerator exhibits a high stability and a good selectivity for glucose sensing. The validity of the biofuel cell-based self-powered biogenerator for continuous neurochemical sensing was illustrated by online continuous monitoring of striatum glucose in rat brain through the combination of in vivo microdialysis. This study offers a new and technically simple platform for continuously monitoring physiologically important species in cerebral systems.

Generation of gaseous sulfur-containing compounds in tumour tissue and suppression of gas diffusion as an antitumour treatment.

BACKGROUND AND AIMS: The mechanisms of cancer cell growth and metastasis are still not entirely understood, especially from the viewpoint of chemical reactions in tumours. Glycolytic metabolism is markedly accelerated in cancer cells, causing the accumulation of glucose (a reducing sugar) and methionine (an amino acid), which can non-enzymatically react and form carcinogenic substances. There is speculation that this reaction produces gaseous sulfur-containing compounds in tumour tissue. The aims of this study were to clarify the products in tumour and to investigate their effect on tumour proliferation. METHODS: Products formed in the reaction between glucose and methionine or its metabolites were analysed in vitro using gas chromatography. Flatus samples from patients with colon cancer and exhaled air samples from patients with lung cancer were analysed using near-edge x-ray fine adsorption structure spectroscopy and compared with those from healthy individuals. The tumour proliferation rates of mice into which HT29 human colon cancer cells had been implanted were compared with those of mice in which the cancer cells were surrounded by sodium hyaluronate gel to prevent diffusion of gaseous material into the healthy cells. RESULTS: Gaseous sulfur-containing compounds such as methanethiol and hydrogen sulfide were produced when glucose was allowed to react with methionine or its metabolites homocysteine or cysteine. Near-edge x-ray fine adsorption structure spectroscopy showed that the concentrations of sulfur-containing compounds in the samples of flatus from patients with colon cancer and in the samples of exhaled air from patients with lung cancer were significantly higher than in those from healthy individuals. Animal experiments showed that preventing the diffusion of sulfur-containing compounds had a pronounced antitumour effect. CONCLUSIONS: Gaseous sulfur-containing compounds are the main products in tumours and preventing the diffusion of these compounds reduces the tumour proliferation rate, which suggests the possibility of a new approach to cancer treatment.

Synergistic Defect Engineering and Interface Stability of Activated Carbon Nanotubes Enabling Ultralong Lifespan All-Solid-State Lithium-Sulfur Batteries.

Due to the high energy density, high safety, and low cost of sulfur, all-solid-state lithium-sulfur batteries (ASSLSBs) are considered one of the most promising next-generation energy storage devices. Nevertheless, the insufficient interfacial contact between solid electrolytes (SEs) and the active material of sulfur leads to inadequate electronic and ionic conduction, which increases interfacial resistance and capacity decay. In this paper, commercial carbon nanotubes (CNTs) are activated to form porous-CNTs (P-CNTs), which are used as sulfur-bearing matrix, forming S@P-CNTs-based composite cathodes for ASSLSBs. Compared with CNTs, P-CNTs possess a larger specific surface area and more oxygen-containing groups, providing enhanced interfacial contact and stability between S@P-CNTs and Li6PS5Cl SE, which are confirmed by scanning electron microscopy, X-ray photoelectron spectroscopy, and density functional theory calculations. Moreover, P-CNTs can form a 3D conductive network in the composite cathodes, facilitating the migration of electrons and the diffusion of ions, as well as improving the utilization of sulfur. As a result, the S@P-CNTs-based ASSLSBs display excellent electrochemical performances, especially rarely reported ultralong lifespan, which deliver a capacity of 1099.2 mA h g-1 at a current density of 1.34 mA cm-2, and remarkably maintain 70.4% of the initial capacity over 1400 cycles.

A promising dehydrogenase-based bioanode for a glucose biosensor and glucose/O2 biofuel cell.

A new type of dehydrogenase-based amperometric glucose biosensor was constructed using glucose dehydrogenase (GDH) which was immobilized on the edge-plane pyrolytic graphite (EPPG) electrode modified with poly(phenosafranin)-functionalized single-walled carbon nanotubes (PPS-SWCNTs). The PPS-SWCNT-modified EPPG electrode was prepared by electropolymerization of phenosafranin on the EPPG electrode which had been previously coated with SWCNTs. The performance of the GDH/PPS-SWCNT/EPPG bioanode was evaluated using cyclic voltammetry and amperometry in the presence of glucose. The GDH/PPS-SWCNT/EPPG electrode possesses promising characteristics as a glucose sensor: a wide linear dynamic range of 50 to 700 µM, low detection limit of 0.3 µM, fast response time (1-2 s), high sensitivity (96.5 µA cm(-2) mM(-1)), and anti-interference and anti-fouling abilities. Moreover, the performance of the GDH/PPS-SWCNT/EPPG bioanode was tested in a glucose/O(2) biofuel cell. The maximum power density delivered by the assembled glucose/O(2) biofuel cell could reach 64.0 µW cm(-2) at a cell voltage of 0.3 V with 40 mM glucose.

Multichalcogen-Integrated Cathodes for Novel Lithium-Chalcogenide Batteries in Ether and Ester Electrolytes.

Lithium-sulfur (Li-S) batteries and lithium-selenium (Li-Se) batteries that contain only one single active element have unique advantages and disadvantages. Inspired by ternary lithium batteries, multielement chalcogenide compounds with integrated advantages may improve upon the performance of lithium-chalcogenide batteries at the source. In this work, activated carbon (AC) with an Al2O3@SiO2 heterojunction is used as the carrier, and the performances and mechanisms of elemental substances (X/AC, X = S, Se, and Te) are studied in ether and ester electrolytes as the basis for preparing multielement chalcogenide composites (SST/AC, SST: S-Se-Te compound). In the ester electrolyte system, SST811/AC (where S/Se/Te = 8:1:1, molar ratio) exhibited the best cycling performance, and the capacity remained at 1024.9 mA h g-1 after 300 cycles. The characterization results revealed the mechanisms and sequences of the gradual liquid-phase reactions of SST/AC in ether electrolytes and the direct solid-phase reactions in ester electrolytes. The active elements in SST/AC fully demonstrated their own functions, enabling the effective construction of new lithium-chalcogenide battery systems. This work provides inspiration for the subsequent research of multielement lithium-chalcogenide batteries and paves the way for their application.

Dilute Electrolyte to Mitigate Capacity Decay and Voltage Fading of Co-Free Li-Rich Cathode for Next-Generation Li-Ion Batteries.

Li-rich cathodes have potential for use in next-generation Li-ion batteries (LIBs) owing to their high specific capacity and low cost. However, their intrinsic cycling decay and voltage fading limit practical applications. In addition, these cathodes contain Co, which is nonrenewable, scarce, and expensive. This situation severely limits the rapid and sustainable development of low-cost LIBs. This paper introduces a novel dilute electrolyte to overcome these limitations based on the Co-free Li-rich Li1.2Mn0.54Ni0.26O2 (LMNO) cathode. An even and robust cathode-electrolyte interface (CEI) formed on the surface of LMNO further protects it from side reactions in the dilute electrolyte. This Co-free Li-rich cathode exhibits the best electrochemical performance reported to date among Li-rich cathodes in terms of outstanding cycling stability (capacity retention of 99.8% at 0.5 C) and dramatically suppressed voltage fading (only 0.3% after 100 cycles). This study demonstrates the potential of Co-free Li-rich cathodes for applications in next-generation LIBs.

pH Dependence of the size and crystallographic orientation of the gold nanoparticles prepared by seed-mediated growth.

The effect of the pH of the growth solution on the size and crystallographic orientation of gold nanoparticles (GNPs) was studied during the course of the preparation of surface-confined spherical GNPs following a two-step protocol (electrochemical and chemical). GNPs were first electrodeposited onto a clean glassy carbon (GC) electrode and these GNPs were used as seeds. Seed-mediated growth of the electrodeposited GNPs was performed in a solution of H[AuCl(4)] at various pHs (5.0 to 0.5) using NH(2)OH as a reducing agent. The thus-prepared GNPs were characterized by electrochemical, UV-visible absorption spectral, SEM, and TEM studies. The nucleation (i.e., formation of the new seeds) was found to dominate over growth (i.e., enlargement of the seed particles) process at higher pH during NH(2)OH seeding, whereas only growth was recognized at low pH (0.5). Nonspherical byproducts were noticed when the seed-mediated growth was performed at higher pHs, but at pH 0.5 only spherical GNPs were observed. The present method provides a way out for the preparation of GNPs with homogeneous shape resolving the problem of simultaneous formation of nonspherical byproducts during the seed-mediated growth as well as for the preparation of GNPs with a Au(111) facet ratio as high as 97%. On the basis of the obtained results, the mechanism of the growth process at low pH is also discussed. Interestingly, an enhanced electrochemical response was obtained for the oxidation of H(2)O(2) using the GNPs prepared at pH 0.5.

Electrodeposition of platinum nanoparticles in a room-temperature ionic liquid.

The electrochemistry of the [PtCl(6)](2-)-[PtCl(4)](2-)-Pt redox system on a glassy carbon (GC) electrode in a room-temperature ionic liquid (RTIL) [i.e., N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium tetrafluoroborate (DEMEBF(4))] has been examined. The two-step four-electron reduction of [PtCl(6)](2-) to Pt, i.e., reduction of [PtCl(6)](2-) to [PtCl(4)](2-) and further reduction of [PtCl(4)](2-) to Pt, occurs separately in this RTIL in contrast to the one-step four-electron reduction of [PtCl(6)](2-) to Pt in aqueous media. The cathodic and anodic peaks corresponding to the [PtCl(6)](2-)/[PtCl(4)](2-) redox couple were observed at ca. -1.1 and 0.6 V vs a Pt wire quasi-reference electrode, respectively, while those observed at -2.8 and -0.5 V were found to correspond to the [PtCl(4)](2-)/Pt redox couple. The disproportionation reaction of the two-electron reduction product of [PtCl(6)](2-) (i.e., [PtCl(4)](2-)) to [PtCl(6)](2-) and Pt metal was also found to occur significantly. The electrodeposition of Pt nanoparticles could be carried out on a GC electrode in DEMEBF(4) containing [PtCl(6)](2-) by holding the potential at -3.5 or -2.0 V. At -3.5 V, the four-electron reduction of [PtCl(6)](2-) to Pt can take place, while at -2.0 V the two-electron reduction of [PtCl(6)](2-) to [PtCl(4)](2-) occurs. The results obtained demonstrate that the electrodeposition of Pt at -3.5 V may occur via a series of reductions of [PtCl(6)](2-) to [PtCl(4)](2-) and further [PtCl(4)](2-) to Pt and at -2.0 V via a disproportionation reaction of [PtCl(4)](2-) to [PtCl(6)](2-) and Pt. Furthermore, the deposition potential of Pt nanoparticles was found to largely influence their size and morphology as well as the relative ratio of Pt(110) and Pt(100) crystalline orientation domains. The sizes of the Pt nanoparticles prepared by holding the electrode potential at -2.0 and -3.5 V are almost the same, in the range of ca. 1-2 nm. These small nanoparticles are "grown" to form bigger particles with different morphologies: In the case of the deposition at -2.0 V, the GC electrode surface is totally, relatively compactly covered with Pt particles of relatively uniform size of ca. 10-50 nm. On the other hand, in the case of the electrodeposition at -3.5 V, small particles of ca. 50-100 nm and the grown-up particles of ca. 100-200 nm cover the GC surface irregularly and coarsely. Interestingly, the Pt nanoparticles prepared by holding the potential at -2.0 and -3.5 V are relatively enriched in Pt(100) and Pt(110) facets, respectively.

Designing conductive networks of hybrid carbon enables stable and long-lifespan cotton-fiber-based lithium-sulfur batteries.

In modern society, flexible rechargeable batteries have become a burgeoning apodictic choice for wearable devices. Conventional lithium-sulfur batteries lack sufficient flexibility because their electrode materials are too rigid to bend. Along with the inherent high theoretical capacity of sulfur, lithium-sulfur batteries have some issues, such as dissolution and shuttle effect of polysulfides, which restricts their efficiency and practicability. Here, a flexible and "dead-weight"-free lithium-sulfur battery substrate with a three-dimensional structure was prepared by a simple strategy. With the cooperative assistance of carbon nanotubes and graphene attached to cotton fibers, the lithium-sulfur battery with 2.0 mg cm-2 sulfur provided a high initial discharge capacity of 1098.7 mA h g-1 at 1C, and the decay rate after 300 cycles was only 0.046% per cycle. The initial discharge capacity at 2C was 872.4 mA h g-1 and the capacity was maintained 734.4 mA h g-1 after 200 cycles with only a 0.079% per cycle decay rate.

Selective detection of As(III) at the Au(111)-like polycrystalline gold electrode.

Selective electrochemical detection of As(III) using a highly sensitive platform based on a Au(111)-like surface is described. The Au(111)-like surface was achieved for the first time by the partial reductive desorption of n-butanethiol (n-BT) from polycrystalline gold (poly-Au), on which a self-assembled monolayer (SAM) of n-BT was formed previously, which allows the selective blockage of the Au(100) and Au(110) surface domains by n-BT while the Au(111) domain remains bare. Square wave anodic stripping voltammetry (SWASV) using the Au(111)-like poly-Au electrode confirms the successful detection of As(III) without any interference from Cu(II). The fabricated electrode is stable and highly sensitive even in the presence of Cu(II), and it shows a linear response for As(III) up to 15 µM. The detection limit (S/N = 3) toward As(III) is 0.28 ppb, which is far below the guideline value given by World Health Organization (WHO). The electrode was applicable for the analysis of spiked arsenic in tap water containing a significant amount of various other ion elements. The results indicate that the Au(111)-like poly-Au electrode could be promising for the electrochemical detection of trace level of As(III) in real samples without any interference from Cu(II).

Noncovalent attachment of NAD+ cofactor onto carbon nanotubes for preparation of integrated dehydrogenase-based electrochemical biosensors.

This study describes a facile approach to the preparation of integrated dehydrogenase-based electrochemical biosensors through noncovalent attachment of an oxidized form of beta-nicotinamide adenine dinucleotide (NAD(+)) onto carbon nanotubes with the interaction between the adenine subunit in NAD(+) molecules and multiwalled carbon nanotubes (MWCNTs). X-ray photoelectron spectroscopic and cyclic voltammetric results suggest that NAD(+) is noncovalently attached onto MWCNTs to form an NAD(+)/MWCNT composite that acts as the electronic transducer for the integrated dehydrogenase-based electrochemical biosensors. With glucose dehydrogenase (GDH) as a model dehydrogenase-based recognition unit, electrochemical studies reveal that glucose is readily oxidized at the GDH/NAD(+)/MWCNT-modified electrode without addition of NAD(+) in the phosphate buffer. The potential for the oxidation of glucose at the GDH/NAD(+)/MWCNT-modified electrode remains very close to that for NADH oxidation at the MWCNT-modified electrode, but it is more negative than those for the oxidation of glucose at the MWCNT-modified electrode and for NADH oxidation at a bare glassy carbon electrode. These results demonstrate that NAD(+) molecules stably attached onto MWCNTs efficiently act as the cofactor for the dehydrogenases. MWCNTs employed here not only serve as the electronic transducer and the support to confine NAD(+) cofactor onto the electrode surface, but also act as the electrocatalyst for NADH oxidation in the dehydrogenase-based electrochemical biosensors. At the GDH/NAD(+)/MWCNT-based glucose biosensor, the current is linear with the concentration of glucose being within a concentration range from 10 to 300 microM with a limit of detection down to 4.81 microM (S/N = 3). This study offers a facile and versatile approach to the development of integrated dehydrogenase-based electrochemical devices, such as electrochemical biosensors and biofuel cells.

EQCM study of the [Au(III)Cl4](-)-[Au(I)Cl2](-)-Au(0) redox system in 1-ethyl-3-methylimidazolium tetrafluoroborate room-temperature ionic liquid.

The electrochemical behavior of the [Au(III)Cl(4)](-)-[Au(I)Cl(2)](-)-Au(0) redox system in room temperature ionic liquid (RTIL) of 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIBF(4)) has been investigated quantitatively using an in situ electrochemical quartz crystal microbalance (EQCM) technique based on a Pt film-coated quartz crystal electrode (Pt-QCE). A series of two-electron (2e) and one-electron (1e) reductions of the [Au(III)Cl(4)](-) to [Au(I)Cl(2)](-) and [Au(I)Cl(2)](-) to Au metal were recognized at the Pt surface. Besides, the disproportionation reaction of [Au(I)Cl(2)](-) (i.e., the 2e-reduction product of [Au(III)Cl(4)](-)) to [Au(III)Cl(4)](-) and Au metal was also observed. Electro-dissolution of the Au deposited on the Pt electrode through a 1e-oxidation reaction in the presence of chloride ions was also confirmed using the Pt-QCE based EQCM technique. A 2e-oxidation reaction of [Au(I)Cl(2)](-) (i.e., the dissolved product) to [Au(III)Cl(4)](-) along with the oxidation of Cl(-) ion on the Pt surface was also realized at high anodic potential. The results demonstrate that in situ EQCM technique is applicable and powerful in elucidating electrochemical surface phenomena accompanying a mass change in RTIL.

High-Efficiency Electrolyte for Li-Rich Cathode Materials Achieving Enhanced Cycle Stability and Suppressed Voltage Fading Capable of Practical Applications on a Li-Ion Battery.

Li-rich cathodes have been in considerable attention for their high reversible capacity. However, they have serious problems like poor cycling with intense capacity decay and voltage fading, which restrict their access to practical applications. In this work, a facile and efficient strategy is proposed to alleviate these intrinsic issues with a high-efficiency electrolyte system. This special electrolyte enables Li-rich cathodes to deliver superior integrated performance with a high initial discharge capacity of 301 mAh·g-1, outstanding cycling stability with a capacity retention of 88% at 0.5 C over 500 cycles, and a remarkable rate capability of 136 mAh·g-1 at 5 C, respectively. What is more, the voltage fading is largely suppressed. Physical and electrochemical characterizations demonstrate that the robust CEI film formed on the cathode surface contributes to the improved electrochemical performance. This work provides a new approach to surmount defects of Li-rich materials and will largely promote their practical applications on Li-ion batteries.

Stability of superoxide ion in imidazolium cation-based room-temperature ionic liquids.

The stability of superoxide ion (O(2)(*-)) generated chemically by dissolving KO(2) in dried dimethyl sulfoxide solutions containing imidazolium cation [e.g., 1-ethyl-3-methylimidazolium (EMI(+)) and 1-n-butyl-2,3-dimethylimidazolium (BMMI(+))] based ionic liquids (ILs) was investigated with UV-visible spectroscopic, NMR, and voltammetric techniques and an ab initio molecular orbital calculation. UV-visible spectroscopic and cyclic voltammetric measurements reveal that the O(2)(*-) species reacts with BMMI(+) and EMI(+) cations of ILs to form hydrogen peroxide. The pseudo first order rate constant for the reaction of BMMI(+) and O(2)(*-) species was found to be about 2.5 x 10(-3) s(-1). With a molecular orbital calculation, the O(2)(*-) species is understood to attack the 2-position (C-2) of the imidazolium ring (i.e., BMMI(+)) to form an ion pair complex in which one oxygen atom is bounded to C-2 and the other to the hydrogen atom of -CH(3) group attached to C-2. Eventually, the ion pair complex of BMMI(+) cation and O(2)(*-) species undergoes a ring opening reaction as evidenced with (1)H NMR measurement.