Bioconversion of Cheese Whey and Food By-Products by Phaeodactylum tricornutum into Fucoxanthin and n-3 Lc-PUFA through a Biorefinery Approach.

This study investigates the potential of utilizing three food wastes: cheese whey (CW), beet molasses (BM), and corn steep liquor (CSL) as alternative nutrient sources for the cultivation of the diatom Phaeodactylum tricornutum, a promising source of polyunsaturated eicosapentaenoic acid (EPA) and the carotenoid fucoxanthin. The CW media tested did not significantly impact the growth rate of P. tricornutum; however, CW hydrolysate significantly enhances cell growth. BM in cultivation medium enhances biomass production and fucoxanthin yield. The optimization of the new food waste medium was conducted through the application of a response surface methodology (RSM) using hydrolyzed CW, BM, and CSL as factors. The results showed a significant positive impact of these factors (p < 0.005), with an optimized biomass yield of 2.35 g L-1 and a fucoxanthin yield of 3.64 mg L-1 using a medium composed of 33 mL L-1 of CW, 2.3 g L-1 of BM, and 2.24 g L-1 of CSL. The experimental results reported in this study showed that some food by-products from a biorefinery perspective could be utilized for the efficient production of fucoxanthin and other high-added-value products such as eicosapentaenoic acid (EPA).

Polyethylene, Polystyrene, and Polypropylene leachate impact upon marine microalgae Dunaliella tertiolecta.

In the aquatic environment, plastics may release several hazardous substances of severe ecotoxicological concern not covalently bound to the polymers. The aim of this study was to examine the adverse effects of leachates of different virgin polymers, polypropylene (PP), polyethylene (PE), and polystyrene (PS) on marine microalgae Dunaliella tertiolecta. The tests carried out on D. tertiolecta included: growth inhibition, oxidative stress (DCFH-DA), and DNA damage (COMET assay). Polypropylene and PS leachates produced growth inhibition at the lowest concentration (3.1% of leachate). In contrast, a hormesis phenomenon was observed with PE leachates. An algae inhibition growth ranking (PP>PS>PE) was noted, based upon EC50 values. Reactive oxygen species (ROS) generated were increased with leachates concentrations with PS exhibiting the highest ROS levels, while a marked genotoxic effect (30%) was found only with PP. All leachates were free from detectable quantities of organic compounds (GC/MS) but showed the presence of transition, post-transition and alkaline earth metals, metalloids, and nonmetals (

Formulation of New Media from Dairy and Brewery Wastes for a Sustainable Production of DHA-Rich Oil by Aurantiochytrium mangrovei.

Mozzarella stretching water (MSW) is a dairy effluent generated from mozzarella cheese production that does not have a real use and is destined to disposal, causing environmental problems and representing a high disposal cost for dairy producers. Spent brewery yeast (SBY) is another promising food waste produced after brewery manufacturing that could be recycled in new biotechnological processes. Aurantiochytrium mangrovei is an aquatic protist known as producer of bioactive lipids such as omega 3 long chain polyunsaturated fatty acids (ω3 LC-PUFA), in particular docosahexaenoic acid (DHA). In this work MSW and SBY have been used to formulate new sustainable growth media for A. mangrovei cultivation and production of DHA in an attempt to valorize these effluents. MSW required an enzymatic hydrolysis to enhance the biomass production. The new media obtained from hydrolysed MSW was also optimized using response surface methodologies, obtaining 10.14 g L-1 of biomass in optimized medium, with a DHA content of 1.21 g L-1.

Marine Collagen from Alternative and Sustainable Sources: Extraction, Processing and Applications.

Due to its unique properties, collagen is used in the growing fields of pharmaceutical and biomedical devices, as well as in the fields of nutraceuticals, cosmeceuticals, food and beverages. Collagen also represents a valid resource for bioplastics and biomaterials, to be used in the emerging health sectors. Recently, marine organisms have been considered as promising sources of collagen, because they do not harbor transmissible disease. In particular, fish biomass as well as by-catch organisms, such as undersized fish, jellyfish, sharks, starfish, and sponges, possess a very high collagen content. The use of discarded and underused biomass could contribute to the development of a sustainable process for collagen extraction, with a significantly reduced environmental impact. This addresses the European zero-waste strategy, which supports all three generally accepted goals of sustainability: sustainable economic well-being, environmental protection, and social well-being. A zero-waste strategy would use far fewer new raw materials and send no waste materials to landfills. In this review, we present an overview of the studies carried out on collagen obtained from by-catch organisms and fish wastes. Additionally, we discuss novel technologies based on thermoplastic processes that could be applied, likewise, as marine collagen treatment.

Early ecotoxic effects of ZnO nanoparticle chronic exposure in Mytilus galloprovincialis revealed by transcription of apoptosis and antioxidant-related genes.

Recently, China became one of the largest nanomaterial markets in the world. The wide use of ZnO nanoparticles in a number of products implies an increasing release in marine environment and consequently the evaluation of the potential effects upon marine organisms largely cultured in China for commercial purposes, such as invertebrate bivalves is a current need. To this aim, survival, bioaccumulation, and transcription pattern of key genes, p53, PDRP, SOD, CAT, and GST, involved in DNA damage/repair and antioxidation, in Mytilus galloprovincialis digestive gland, exposed to ZnO NPs (<100 nm) and ZnO bulk (150-200 nm) for 4 weeks, were evaluated. ZnSO4 was also assessed to appraise the role of zinc ions. Starting from 72 h, increasing mortality values along the exposure time were observed for all ZnO compounds. The highest difference was evident after 28 d when NPs resulted three times more toxic than bulk, (LC50) = 0.78 mg Zn/L (confidence limits: 0.64, 1.00) and 2.62 mg Zn/L (confidence limits: 1.00, 4.00), respectively. For ZnSO4 the (LC50) was always the lowest reaching the minimum value at 28 d 0.25 mg Zn/L (confidence limits: 0.10-0.40). Digestive gland showed higher uptake rate of ionic Zn respect to ZnO NPs and bulk during the first three days of exposure. In particular at the end of the exposure time (28 d) at 1 mg Zn/L the rank of Zn uptake rate was Zinc ion > ZnO NPs > ZnO bulk. The relative expression of investigated genes evidenced that distinct actions of apoptosis and antioxidation occurred in M. galloprovincialis exposed to ZnO NPs with a peculiar pattern dependent on exposure time and concentration. Application of the qRT-PCR technique revealed evidence of sensitivity to the nanomaterial since the first time of exposure.

Mild Approach for the Formulation of Chestnut Flour-Enriched Snacks: Influence of Processing Parameters on the Preservation of Bioactive Compounds of Raw Materials.

Third-generation snacks were developed from a triad of flours made up of chestnut, spelt, and chickpea flour. Optimal snack formulations and processing parameters have been established to ensure acceptable workability of the raw dough while protecting the bioactive components of the raw materials. The parameters examined were mixing time, speed, and temperature. The properties of the snack were evaluated by analyzing the expansion ratio, hardness, moisture content, and phenolic and volatile compounds. The optimal mixing conditions that ensure maximum expansion were a temperature of 30 °C, a speed of 30 rpm, and a time of 6 min. The results showed that the proper percentage of water and sodium bicarbonate was 35% and 2%, respectively, and that the developed snacks had an alveolar and homogeneous structure. The proposed approach brings several advantages, including the preservation of bioactive compounds during the production process. Furthermore, the mild operating conditions prevented the development of unwanted or unpleasant compounds, as confirmed by the analysis of volatile compounds. Therefore, this study opens new perspectives in the food industry, satisfying the growing demand for functional products and healthy snacks.

Antibiotic Resistance of Bacteria Isolated from Clinical Samples and Organs of Rescued Loggerhead Sea Turtles (Caretta caretta) in Southern Italy.

Antimicrobial resistance affects all environments, endangering the health of numerous species, including wildlife. Increasing anthropic pressure promotes the acquisition and dissemination of antibiotic resistance by wild animals. Sea turtles, being particularly exposed, are considered sentinels and carriers of potential zoonotic pathogens and resistant strains. Therefore, this study examined the antibiotic resistance profiles of bacteria isolated from loggerhead sea turtles hospitalised in a rescue centre of Southern Italy over a 9-year period. Resistance to ceftazidime, doxycycline, enrofloxacin, flumequine, gentamicin, oxytetracycline and sulfamethoxazole-trimethoprim was evaluated for 138 strains isolated from the clinical samples or organs of 60 animals. Gram-negative families were the most isolated: Vibrionaceae were predominant, followed by Shewanellaceae, Pseudomonadaceae, Enterobacteriaceae and Morganellaceae. These last three families exhibited the highest proportion of resistance and multidrug-resistant strains. Among the three Gram-positive families isolated, Enterococcaceae were the most represented and resistant. The opportunistic behaviour of all the isolated species is particularly concerning for diseased sea turtles, especially considering their resistance to commonly utilised antibiotics. Actually, the multiple antibiotic resistance was higher when the sea turtles were previously treated. Taken together, these findings highlight the need to improve antimicrobial stewardship and monitor antibiotic resistance in wildlife, to preserve the health of endangered species, along with public and environmental health.

First description of Rhodococcus equi infection in common bottlenose dolphin (Tursiops truncatus).

Rhodococcus equi is a terrestrial bacterium and a common pathogen in foals (Equus caballus), in which causes pneumonia. This report describes for the first time the infection caused by R. equi in a common bottlenose dolphin (Tursiops truncatus) stranded in the Calabrian coast, Italy. The post mortem examination of the animal revealed lesions in lung and colon. The animal was also positive to dolphin morbillivirus. The histological study showed lesions attributable to R. equi infection, such as pyogranulomatous bacterial pneumonia and chronic granulomatous colitis. Whole genome sequencing of the isolated strain confirmed its identification as R. equi.

Genomic Characterization of Listeria monocytogenes and Other Listeria Species Isolated from Sea Turtles.

Listeria monocytogenes is a ubiquitous pathogen found both in the environment and food. It can cause listeriosis in a wide range of animals as well as in humans. Investigations on presence, spread and virulence are still limited to terrestrial and human environments. Embracing the One Health Approach, investigating the presence and spread of L. monocytogenes in marine ecosystems and among wildlife, would provide us with useful information for human health. This study investigated the presence of L. monocytogenes and Listeria spp. in two species of sea turtles common in the Mediterranean Sea (Caretta caretta and Chelonia mydas). A total of one hundred and sixty-four carcasses of sea turtles (C. caretta n = 161 and C. mydas n = 3) stranded along the Abruzzo, Molise, Campania, and Calabria coasts, were collected. Brain and fecal samples were taken, enriched, and cultured for the detection of Listeria spp. From the specimens collected, strains of L. monocytogenes (brain n = 1, brain and feces n = 1, multiorgan n = 1 and feces n = 1), L. innocua (feces n = 1 and brain n = 1), and L. ivanovii (brain n = 1) were isolated. Typical colonies were isolated for Whole Genome Sequencing (WGS). Virulence genes, disinfectants/metal resistance, and antimicrobial resistance were also investigated. L. monocytogenes, L. innocua, and L. ivanovii were detected in C. caretta, whilst only L. monocytogenes and L. innocua in C. mydas. Notable among the results is the lack of significant differences in gene distribution between human and sea turtle strains. Furthermore, potentially pathogenic strains of L. monocytogenes were found in sea turtles.

Effect of Cellulose-Based Bioplastics on Current LDPE Recycling.

The increased use of bioplastics in the market has led to their presence in municipal solid waste streams alongside traditional fossil-based polymers, particularly low-density polyethylene (LDPE), which bioplastics often end up mixed with. This study aimed to assess the impact of cellulose acetate plasticized with triacetin (CAT) on the mechanical recycling of LDPE. LDPE-CAT blends with varying CAT content (0%, 1%, 5%, 7.5%, and 10% by weight) were prepared by melt extrusion and analyzed using scanning electron microscopy, Fourier-transform infrared spectroscopy, thermal analysis (thermogravimetric and differential scanning calorimetry), dynamic rheological measurements, and tensile tests. The results indicate that the presence of CAT does not significantly affect the chemical, thermal, and rheological properties of LDPE, and the addition of CAT at different levels does not promote LDPE degradation under typical processing conditions. However, the addition of CAT negatively impacts the processability and mechanical behavior of LDPE, resulting in the reduced quality of the recycled material. Thus, the presence of cellulose-based bioplastics in LDPE recycling streams should be avoided, and a specific sorting stream for bioplastics should be established.

Use of Different Organic Carbon Sources in Cynara cardunculus Cells: Effects on Biomass Productivity and Secondary Metabolites.

Cynara cardunculus (Asteraceae family) is a perennial plant native to Mediterranean regions. This plant represents a source of high-value compounds, such as polyphenols and fatty acids that have several industrial applications. However, in vitro plant cell cultures can represent a valid alternative to in-field cultivation and facilitate the extraction of metabolites of commercial interest. Generally, sucrose is the main sugar used for plant cell cultures, but other carbon sources can be considered. Here, we investigated the potential use of alternative organic carbon sources, such as galactose, maltose, glucose, glycerol, fructose, lactose, and starch, for the cultivation of C. cardunculus cells. Moreover, cardoon cells were collected, and an extraction of polyphenols and oils was performed to study the effects of different carbon sources on the production of bioactive molecules. This study provided evidence that cardoon cell growth can be supported by carbon sources other than sucrose. However, the carbon source inducing optimum growth, did not necessarily induce the highest production of high-value compounds.

The influence of bio-plastics for food packaging on combined anaerobic digestion and composting treatment of organic municipal waste.

The use of bio-plastic-based packaging as an alternative to conventional plastic packaging is increasing. Among the plethora of different bio-based plastics, the most relevant ones are those that, at the end of their life, can be treated with the organic fraction of municipal solid waste. Even in these cases, their impact on the waste processing and recycling is not always positive. This study aim to assess on a laboratory scale the influence on combined anaerobic digestion and composting industrial processes of a bio-based plastic film, namely cellulose acetate (CA), in pure and modified (additions of additive) forms. CA films were mixed with organic waste and subjected to: (i) anaerobic digestion; (ii) active composting and (iii) two stages of curing composting. Anaerobic digestion and composting were monitored through methane yield and oxygen uptake respectively; additionally, the bio-plastics degree of disintegration was assessed during all the processes. The final disintegration of pure and modified CA was 73.82% and 54.66%, respectively. Anaerobic digestion contributes to the disintegration of the material, while aerobic treatment appears to be nearly ineffective, especially for modified CA. The presence of cellulose acetate during anaerobic digestion of food waste increased the methane yield by about 4.5%. Bioassay confirmed the absence of possible toxic effects on the final compost from the bio-plastic treatment. Although bio-based materials are not the only solution to plastic pollution, the findings confirm the need to upgrade the organic waste treatment plants and the necessity to revise the requirements for the use of compost in agriculture.

Sustainable production of food grade omega-3 oil using aquatic protists: Reliability and future horizons.

Biotechnological production of omega-3 polyunsaturated fatty acids (PUFAs) has become a commercial alternative to fish oil in the past twenty years. Compared to PUFA production by fatty fishes, that from microorganisms has increased due to its promising sustainability and high product safety and to increasing awareness in the expanding vegan market. Although autotrophic production by microalgae seems to be more sustainable in the long term, to date most of the microbial production of omega-3 is carried out under heterotrophic conditions using conventional fermentation technologies. The present review critically analyzes the main reasons for this discrepancy and reports on the recent advances and the most promising approaches for its future development in the context of sustainability and circular economy.

Design of novel three-phase PCL/TZ-HA biomaterials for use in bone regeneration applications.

The design of bioactive scaffold materials able to guide cellular processes involved in new-tissue genesis is key determinant in bone tissue engineering. The aim of this study was the design and characterization of novel multi-phase biomaterials to be processed for the fabrication of 3D porous scaffolds able to provide a temporary biocompatible substrate for mesenchymal stem cells (MSCs) adhesion, proliferation and osteogenic differentiation. The biomaterials were prepared by blending poly(epsilon-caprolactone) (PCL) with thermoplastic zein (TZ), a thermoplastic material obtained by de novo thermoplasticization of zein. Furthermore, to bioactivate the scaffolds, microparticles of osteoconductive hydroxyapatite (HA) were dispersed within the organic phases. Results demonstrated that materials and formulations strongly affected the micro-structural properties and hydrophilicity of the scaffolds and, therefore, had a pivotal role in guiding cell/scaffold interaction. In particular, if compared to neat PCL, PCL-HA composite and PCL/TZ blend, the three-phase PCL/TZ-HA showed improved MSCs adhesion, proliferation and osteogenic differentiation capability, thus demonstrating potential for bone regeneration.

Adverse effects of oxo-degradable plastic leachates in freshwater environment.

The production of biodegradable plastics is considered to be a way to reduce plastic waste issue. Among others, oxo-degradant additives enable a faster degradation of plastics in the environment. However, the introduction of these new materials could provoke the release of substances potentially toxic in the environment. This work determined and compared the toxicity of leachates from various additivated polymers (polyethylene, PE; polypropylene, PP; polystyrene, PS) upon different test organisms: plants (Sorghum saccharatum, Lepidium sativum, Sinapis alba, and Vicia faba), crustacean (Daphnia magna), and luminescent bacteria (Vibrio fischeri). Daphnia magna survival was mainly affected by PS and PP leachates (72% and 61% effect, respectively) while PS notably reduced the reproduction rate. On plants, only PP exerted a negative effect (S. saccharatum IG% 32.4), while V. fischeri always showed values around 50%. The data integration, through the Toxicity Test Battery Integrated Index (TBI) approach, allowed to rank the leachates toxicity as PE > PS > PP. This result could be mainly ascribable to the highest metals content in PE since no difference with organic compounds analysis was evidenced. In conclusion, since the polymers exerted dissimilar toxicity, the additive could not be considered the sole responsible of the measured toxicity, but its role in the enhancement of the virgin polymers leachates effects can be solidly hypothesized.

DNA damages and offspring quality in sea urchin Paracentrotus lividus sperms exposed to ZnO nanoparticles.

The recent advances in nanotechnology lead to a potential increase of the release of nanoparticles (NPs) into marine environment through different routes, with possible toxic effects upon the living part of this ecosystem. One of the ways of NPs marine contamination gaining today increasing concern stems from the widespread use cosmetics containing ZnO NPs as UV-filter. Although the possible adverse effects on marine organisms have been already ascertained, the information about the possible genotoxicity of ZnO NPs is still scant. In this work the spermiotoxicity of ZnO particles of different sizes (ZnO Bulk > 200 nm, ZnO NPs 100 nm and ZnO NPs 14 nm) was assessed, using Paracentrotus lividus spermatozoa, by evaluating the DNA damage of the exposed sperm, fertilization capability and DNA damage transmission to progeny. Our results showed that ZnO NPs induced DNA damages in spermatozoa after 30 min of exposure. While the sperm fertilization capability was not affected, morphological alterations (skeletal alterations) in offspring were observed and a positive correlation between sperm DNA damage and offspring quality was reported. This study underlines that a possible spermiotoxic action of ZnO NPs at concentration close to those reported in marine coastal water could occur.

Vegetable Tannin as a Sustainable UV Stabilizer for Polyurethane Foams.

A vegetable tannin, a flavonoid-type natural polyphenolic compound, was used to promote the stabilization of polyurethane foams against UV radiation. Several polyurethane foams were synthesized by using an isocyanate, and a mixture of ethoxylated cocoalkyl amine and vegetable tannin. The content of vegetable tannin was varied from 0 to 40 wt %. The effects of tannin and water (used as a blowing agent) on the foaming kinetics and cellular morphology of foams were investigated. Samples were subjected to accelerated weathering under UV radiation for 3 to 24 h, and FTIR and DMA analyses were conducted to assess the performance change. The former analysis revealed a strong inhibiting effect of tannin on urethane linkage degradation during the UV treatment. The mechanical properties were significantly affected by the addition of tannin. The capability of the foams to withstand UV radiation was dependent on the amount of tannin. At tannin contents higher than 20%, the decrease in mechanical properties under UV irradiation was almost avoided.

Leachates of micronized plastic toys provoke embryotoxic effects upon sea urchin Paracentrotus lividus.

Microplastics are defined as plastic fragments <5 mm, and they are found in the ocean where they can impact on the ecosystem. Once released in seawater, microplastics can be internalized by organisms due to their small size, moreover they can also leach out several additives used in plastic manufacturing, such as plasticizers, flame retardants, etc., resulting toxic for biota. The aim of this study was to test the toxicity of micronized PVC products with three different colors, upon Paracentrotus lividus embryos. In particular, we assessed the effects of micronized plastics and microplastic leachates. Results showed a decrease of larval length in plutei exposed to low concentrations of micronized plastics, and a block of larval development in sea urchin embryos exposed to the highest dose. Virgin PVC polymer did not result toxic on P. lividus embryos, while an evident toxic effect due to leached substances in the medium was observed. In particular, the exposure to leachates induced a development arrest immediately after fertilization or morphological alterations in plutei. Finally, PVC products with different colors showed different toxicity, probably due to a different content and/or combination of heavy metals present in coloring agents.

Enhancing the EMI shielding of natural rubber-based supercritical CO2 foams by exploiting their porous morphology and CNT segregated networks.

Natural rubber/carbon nanotubes composite foams (F-NR/CNTs) with high electrical conductivity and excellent electromagnetic interference (EMI) performance were developed through a multi-step process including: (a) CNTs assembled on natural rubber latex particles, (b) pre-crosslinking of natural rubber, (c) supercritical carbon dioxide foaming of pre-crosslinked composite samples and (d) post-crosslinking of foamed composite samples. A closed-cell porous structure and a segregated CNT network are clearly observed in the resulting foams. Due to this morphology, F-NR/CNTs exhibit low density, good mechanical properties, and high electrical conductivity. Owing to the multiple radiation reflections and scattering between the cell-matrix interfaces, the composite foams presented an excellent specific shielding effectiveness (SSE) of 312.69 dB cm2 g-1 for F-NR/CNTs containing 6.4 wt% of CNTs, which is significantly higher than those already published for rubber composites containing comparable filler content. Furthermore, the analysis of EMI SE highlights that absorption efficiency is more significant than reflection efficiency, implying that most of the incident electromagnetic radiation is dissipated in the form of heat. This work provides the fundamentals for the design of innovative light weight and efficient EMI shielding foams characterized by a three-dimensional segregated CNT network with huge potential for use in the electronics and aerospace industries.