RESUMO
We demonstrate a broadband acousto-optic notch filter based on a tubular-lattice hollow-core fiber for the first time to our knowledge. The guided optical modes are modulated by acoustically induced dynamic long-period gratings along the fiber. The device is fabricated employing a short interaction length (7.7â cm) and low drive voltages (10â V). Modulated spectral bands with 20â nm half-width and maximum depths greater than 60% are achieved. The resonant notch wavelength is tuned from 743 to 1355â nm (612â nm span) by changing the frequency of the electrical signal. The results indicate a broader tuning range compared to previous studies using standard and hollow-core fibers. It further reveals unique properties for reconfigurable spectral filters and fiber lasers, pointing to the fast switching and highly efficient modulation of all-fiber photonic devices.
RESUMO
In this article, a new and flexible approach to control the electric field enhancement of bow-tie nano-antennas by integrating them on the lateral of a tapered optical fiber is proposed. The device is driven by a Q-switched laser and the performance of a fabricated nano-antenna in a quartz slide is tested by a Surface Enhanced Raman Scattering (SERS) experiment. A refractive index sensing experiment is also performed and a sensitivity of (240 ± 30) nm/RIU is found in the 1.33-1.35 index range.
RESUMO
In this paper the development of a side-hole photonic-crystal fiber (SH-PCF) pressure sensor for dual environment monitoring is reported. SH-PCF properties (phase and group birefringence, sensitivity to pressure variations) are measured and compared to simulated data. In order to probe two environments, two sections of the SH-PCF with different lengths are spliced and set in a Solc filter-like configuration. This setup allows obtaining the individual responses of the first and second fiber independently, which is useful for a space-multiplexed measurement. As the employed fiber is sensitive to pressure variations, we report the use of this configuration for dual environment pressure sensing.
RESUMO
An optical fiber sensor based on the combination of two spliced birefringent optical fiber sections is proposed in this paper. The sensor is built up in a Solc-filter-like configuration and a simple theoretical model based on Jones matrices is employed to predict experimental results. By choosing the suitable birefringent optical fibers (e.g., photonic crystal fibers, birefringent microfibers, elliptical core fibers, PANDA fibers, etc.), the sensor described herein allows for probing of two physical parameters (e.g., refractive index and temperature, hydrostatic pressure and temperature) or sensing the same parameter in two disconnected environments. In order to demonstrate the sensor performance, the system response was evaluated in a temperature-sensing measurement.
RESUMO
While optical fibers display excellent performances in the infrared, visible and ultraviolet ranges remain poorly addressed by them. Obtaining better fibers for the short-wavelength range has been restricted, in all fiber optics, by scattering processes. In hollow-core fibers, the scattering loss arises from the core roughness and represents the limiting factor for loss reduction regardless of the cladding confinement power. Here, we report on the reduction of the core surface roughness of hollow-core fibers by modifying their fabrication technique. The effect of the modified process has been quantified and the results showed a root-mean-square surface roughness reduction from 0.40 to 0.15 nm. The improvement in the core surface entailed fibers with ultralow loss at short wavelengths. The results reveal this approach as a promising path for the development of hollow-core fibers with loss that can potentially be orders of magnitude lower than the ones achievable with silica-core counterparts.
RESUMO
Remarkable recent demonstrations of ultra-low-loss inhibited-coupling (IC) hollow-core photonic-crystal fibres (HCPCFs) established them as serious candidates for next-generation long-haul fibre optics systems. A hindrance to this prospect and also to short-haul applications such as micromachining, where stable and high-quality beam delivery is needed, is the difficulty in designing and fabricating an IC-guiding fibre that combines ultra-low loss, truly robust single-modeness, and polarisation-maintaining operation. The design solutions proposed to date require a trade-off between low loss and truly single-modeness. Here, we propose a novel IC-HCPCF for achieving low-loss and effective single-mode operation. The fibre is endowed with a hybrid cladding composed of a Kagome-tubular lattice (HKT). This new concept of a microstructured cladding allows us to significantly reduce the confinement loss and, at the same time, preserve truly robust single-mode operation. Experimental results show an HKT-IC-HCPCF with a minimum loss of 1.6 dB/km at 1050 nm and a higher-order mode extinction ratio as high as 47.0 dB for a 10 m long fibre. The robustness of the fibre single-modeness is tested by moving the fibre and varying the coupling conditions. The design proposed herein opens a new route for the development of HCPCFs that combine robust ultra-low-loss transmission and single-mode beam delivery and provides new insight into IC guidance.
RESUMO
The aim of this study was to evaluate the biomechanical properties expressed by shrinkage stress, cuspal strain, fracture strength and failure mode in molars with large class II mesio-occlusal-distal restorations. Sixty-four human caries-free third molars were selected and distributed randomly into four groups: Z100 restorative material (Z100), Tetric N-Ceram Bulk-Fill (TNC), Filtek Bulk-Fill (FBF) and Aura Ultra Universal (ABF). The bulk-fill materials were inserted in one singular bulk increment and the conventional composite resin in three ones. Polymerisation shrinkage stress was evaluated by optical Fibre Bragg Gratings (FBG) sensors (nâ¯=â¯6). The cuspal deformation was measured using an extensometer during three moments: restorative procedure, axial compressive loading and at fracture (nâ¯=â¯10). The fracture strength was evaluated on a universal machine. The failure mode was analysed by Scanning Electron Microscopy (SEM). Data were analysed using one-way ANOVA tests with Tukey's posthoc test (αâ¯=â¯5%). Data of the failure mode were submitted to a likelihood ratio chi-square test. Z100 presented the highest mean value for the shrinkage stress (pâ¯<â¯0.05) by FBG evaluation, whereas bulk-fill resin groups presented low polymerisation stress mean value, especially the TNC (pâ¯<â¯0.05). The cuspal deformation test showed that Z100 presented a significant difference mean value compared to the other groups (pâ¯<â¯0.01) during the restoration and compressive axial force; however, load until the fracture presented a difference only between TNC and FBF (pâ¯<â¯0.05). The fracture strength of TNC was statistically different from Z100 (pâ¯<â¯0.01). The failure mode was not statistically different in all the groups (pâ¯>â¯0.05). Bulk-fill composites promoted less polymerisation shrinkage stress than conventional microhybrid composite during and after the light curing process in class II posterior resin composite restorations.
Assuntos
Resinas Compostas , Restauração Dentária Permanente , Teste de Materiais , Fenômenos Mecânicos , Fenômenos BiomecânicosRESUMO
Understanding cladding properties is crucial for designing microstructured optical fibers. This is particularly acute for Inhibited-Coupling guiding fibers because of the reliance of their core guidance on the core and cladding mode-field overlap integral. Consequently, careful planning of the fiber cladding parameters allows obtaining fibers with optimized characteristics such as low loss and broad transmission bandwidth. In this manuscript, we report on how one can tailor the modal properties of hollow-core photonic crystal fibers by adequately modifying the fiber cladding. We show that the alteration of the position of the tubular fibers cladding tubes can alter the loss hierarchy of the modes in these fibers, and exhibit salient polarization propriety. In this context, we present two fibers with different cladding structures which favor propagation of higher order core modes - namely LP11 and LP21 modes. Additionally, we provide discussions on mode transformations in these fibers and show that one can obtain uncommon intensity and polarization profiles at the fiber output. This allows the fiber to act as a mode intensity and polarization shaper. We envisage this novel concept can be useful for a variety of applications such as hollow core fiber based atom optics, atom-surface physics, sensing and nonlinear optics.
RESUMO
In this paper, we propose a way to simplify the design of microstructured optical fibres with high sensitivity to applied pressure. The use of a capillary fibre with an embedded core allows the exploration of the pressure-induced material birefringence due to the capillary wall displacements and the photoelastic effect. An analytical description of pressure-induced material birefringence is provided, and fibre modal characteristics are explored through numerical simulations. Moreover, a capillary fibre with an embedded core is fabricated and used to probe pressure variations. Even though the embedded-core fibre has a non-optimized structure, measurements showed a pressure sensitivity of (1.04 ± 0.01) nm/bar, which compares well with more complex, specially designed fibre geometries reported in the literature. These results demonstrate that this geometry enables a novel route towards the simplification of microstructured fibre-based pressure sensors.