Flexible Graphite/PPG Hybrid Composite-Based Resistive Sensor for Sensing Organic Compounds.

Our objective in this study was to investigate a sensor for volatile organic compounds based on a graphite (G)/polypropylene glycol (PPG) hybrid composite (HC) for sensing hybrid elements. The G/PPG HC sensor films for organic-matter detection were successfully fabricated on polyethylene terephthalate (PET) film with a simple blade-coating method. The sensing paste based on G/PPG (1:2) HC showed good dispersibility and stability. In addition, G/PPG HC sensor films with organic compounds showed different thickness changes as a function of the G/PPG ratio because of the swelling effect of the polymer. The observed differences in resistance of the G/PPG HC films corresponded to those of common organic compounds, suggesting that the disconnection of graphite caused by the swollen PPG matrix caused explosive resistance change. Moreover, we evaluated the sensitivity of typical hydrocarbon materials, such as benzene and toluene, in the sensor film as well as petroleum materials without moisture-induced malfunctions. This study could provoke knowledge about superior sensing with cost-effective and easily scalable materials using polymer/graphite composite-based sensors to improve the sensitivity, selectivity, and stability of chemical sensor applications.

Influence of Growth Temperature on the Characteristics of Single-Junction p­i­n InGaP Solar Cells.

Single-junction p­i­n InGaP solar cells are grown at various temperatures from 620 to 700 °C by low pressure metalorganic chemical vapor deposition on GaAs (001) substrates. The short circuit current density of the p­i­n InGaP solar cells increases by up to 38.8% when the growth temperature is reduced from 700 to 620 °C, while the open circuit voltage and fill factor show relatively small changes. The external quantum efficiency, especially, in the wavelength regime below 500 nm, is improved for the p­i­n InGaP solar cells grown at lower temperatures. The improvement might be attributed to the reduced absorption loss of the photons in the n-InGaP emitter region. The highest conversion efficiency of 11.01% is attributed from the p­i­n InGaP solar cell grown at 640 °C. Electron mobility and concentration of undoped InGaP layers are investigated as a function of the growth temperature and correlated with the p­i­n InGaP solar cell performance.

Efficient removal of arsenic by strategically designed and layer-by-layer assembled PS@+rGO@GO@Fe3O4 composites.

The PS@+rGO@GO@Fe3O4 (PG-Fe3O4) hybrid composites for Arsenic removal were successfully fabricated and well dispersed using layer-by-layer assembly and a hydrothermal method. The PG-Fe3O4 hybrid composites were composed of uniformly coated Fe3O4 nanoparticles on graphene oxide layers with water flow space between 3D structures providing many contact area and adsorption sites for Arsenic adsorption. The PG-Fe3O4 hybrid composite has large surface adsorption sites and exhibits high adsorption capacities of 104 mg/g for As (III) and 68 mg/g for As (V) at 25 °C and pH 7 comparison with pure Fe3O4 and P-Fe3O4 samples.

Electrochemically synthesized broadband antireflective and hydrophobic GaOOH nanopillars for III-V InGaP/GaAs/Ge triple-junction solar cell applications.

We report the efficiency enhancement of III-V InGaP/GaAs/ Ge triple-junction (TJ) solar cells using a novel structure, i.e., vertically-oriented gallium oxide hydroxide (GaOOH) nanopillars (NPs), as an antireflection coating. The optical reflectance properties of rhombus-shaped GaOOH NPs, which were synthesized by a simple, low-cost, and large-scalable electrochemical deposition method, were investigated, together with a theoretical analysis using the rigorous coupled-wave analysis method. For the GaOOH NPs, the solar weighted reflectance of ~8.5% was obtained over a wide wavelength range of 300-1800 nm and their surfaces exhibited a high water contact angle of ~130° (i.e., hydrophobicity). To simply demonstrate the feasibility of device applications, the GaOOH NPs were incorporated into a test-grown InGaP/GaAs/Ge TJ solar cell structure. For the InGaP/GaAs/Ge TJ solar cell with broadband antireflective GaOOH NPs, the conversion efficiency (η) of ~16.47% was obtained, indicating an increased efficiency by 3.47% compared to the bare solar cell (i.e., η~13%).

Electrochemically synthesized broadband antireflective and hydrophobic GaOOH nanopillars for III-V InGaP/GaAs/Ge triple-junction solar cell applications.

We report the efficiency enhancement of III-V InGaP/GaAs/ Ge triple-junction (TJ) solar cells using a novel structure, i.e., vertically-oriented gallium oxide hydroxide (GaOOH) nanopillars (NPs), as an antireflection coating. The optical reflectance properties of rhombus-shaped GaOOH NPs, which were synthesized by a simple, low-cost, and large-scalable electrochemical deposition method, were investigated, together with a theoretical analysis using the rigorous coupled-wave analysis method. For the GaOOH NPs, the solar weighted reflectance of ~8.5% was obtained over a wide wavelength range of 300-1800 nm and their surfaces exhibited a high water contact angle of ~130° (i.e., hydrophobicity). To simply demonstrate the feasibility of device applications, the GaOOH NPs were incorporated into a test-grown InGaP/GaAs/Ge TJ solar cell structure. For the InGaP/GaAs/Ge TJ solar cell with broadband antireflective GaOOH NPs, the conversion efficiency (η) of ~16.47% was obtained, indicating an increased efficiency by 3.47% compared to the bare solar cell (i.e., η~13%).

Single-material zinc sulfide bi-layer antireflection coatings for GaAs solar cells.

We demonstrated the efficiency improvement of GaAs single-junction (SJ) solar cells with the single-material zinc sulfide (ZnS) bi-layer based on the porous/dense film structure, which was fabricated by the glancing angle deposition (GLAD) method, as an antireflection (AR) coating layer. The porous ZnS film with a low refractive index was formed at a high incident vapor flux angle of 80° in the GLAD. Each optimum thickness of ZnS bi-layer was determined by achieving the lowest solar weighted reflectance (SWR) using a rigorous coupled-wave analysis method in the wavelength region of 350-900 nm, extracting the thicknesses of 20 and 50 nm for dense and porous films, respectively. The ZnS bi-layer with a low SWR of ~5.8% considerably increased the short circuit current density (J(sc)) of the GaAs SJ solar cell to 25.57 mA/cm(2), which leads to a larger conversion efficiency (η) of 20.61% compared to the conventional one without AR layer (i.e., SWR~31%, J(sc) = 18.81 mA/cm(2), and η = 14.82%). Furthermore, after the encapsulation, its J(sc) and η values were slightly increased to 25.67 mA/cm(2) and 20.71%, respectively. For the fabricated solar cells, angle-dependent reflectance properties and external quantum efficiency were also studied.

Large-scale graphene micropatterns via self-assembly-mediated process for flexible device application.

We report on a method for the large-scale production of graphene micropatterns by a self-assembly mediated process. The evaporation-induced self-assembly technique was engineered to produce highly ordered graphene patterns on flexible substrates in a simplified and scalable manner. The crossed stripe graphene patterns have been produced over a large area with regions consisting of single- and two-layer graphene. Based on these graphene patterns, flexible graphene-based field effect transistors have been fabricated with an ion-gel gate dielectric, which operates at low voltages of < 2 V with a hole and electron mobility of 214 and 106 cm(2)/V·s, respectively. The self-assembly approach described here may pave the way for the nonlithographic production of graphene patterns, which is scalable to large areas and compatible with roll-to-roll system.

Fabrication of a pure TiO2 thin film using a self-polymeric titania nano-sol and its properties.

A pure TiO2 thin film without adding any organic binder was fabricated by using a self-polymeric titania nano-sol (14 mass%), which was prepared by the acid peptization method. The particle size distribution in the 14 mass% TiO2 sol, in which almost of particles had a size below 10.2 nm and the crystal phase confirmed by X-ray diffraction analysis was anatase. The diluted nano-sol had a capability to form a thin film at a low temperature (100-400 degrees C) on the slide glass by dipping method. The average thickness of a coating film was measured to be about 0.25-0.30 microm. A coated film had a high refractive index over 1.88 at least irrespective of the heat-treatment even at room temperature drying and showed a super-hydrophilicity (< 5 degrees) after 20 minutes under Ultra Violet light irradiation, and it sustained in the darkness during a long period over 7 days depending on the heat-treatment conditions. Atomic Force Microscopic observation shows that the morphology of a heat-treated film had a relationship with the long-term hydrophilicity in the darkness.

Optional vena cava filter with disengaging centering struts: retrieval in an animal model.

An optional inferior vena cava (IVC) filter prototype was evaluated for safety and long-term retrievability as an initial feasibility study in an animal model. This filter has four centering struts that have the ability to disengage from the filtering cone portion, allowing the legs to slide out of endothelial growth. Retrieval of six filters in three animals was successful up to 27 weeks. There was no substantial filter tilt, migration, or IVC damage. In conclusion, this filter design may help overcome some of the shortcomings in currently approved optional IVC filters, including long-term retrieval difficulties, tilting, or migration.

Innovatively Continuous Mass Production Couette-taylor Flow: Pure Inorganic Green-Emitting Cs4PbBr6 Perovskite Microcrystal for display technology.

We report for the first time the mass production of Cs4PbBr6 perovskite microcrystal with a Couette-Taylor flow reactor in order to enhance the efficiency of the synthesis reaction. We obtained a pure Cs4PbBr6 perovskite solid within 3 hrs that then realized a high photoluminescence quantum yield (PLQY) of 46%. Furthermore, the Cs4PbBr6 perovskite microcrystal is applied with red emitting K2SiF6 phosphor on a blue-emitting InGaN chip, achieving a high-performance luminescence characteristics of 9.79 lm/W, external quantum efficiency (EQE) of 2.9%, and correlated color temperature (CCT) of 2976 K; therefore, this perovskite is expected to be a promising candidate material for applications in optoelectronic devices.

Ge nanopillar solar cells epitaxially grown by metalorganic chemical vapor deposition.

Radial junction solar cells with vertically aligned wire arrays have been widely studied to improve the power conversion efficiency. In this work, we report the first Ge nanopillar solar cell. Nanopillar arrays are selectively patterned on p-type Ge (100) substrates using nanosphere lithography and deep reactive ion etching processes. Nanoscale radial and planar junctions are realized by an n-type Ge emitter layer which is epitaxially grown by MOCVD using isobutylgermane. In situ epitaxial surface passivation is employed using an InGaP layer to avoid high surface recombination rates and Fermi level pinning. High quality n-ohmic contact is realized by protecting the top contact area during the nanopillar patterning. The short circuit current density and the power conversion efficiency of the Ge nanopillar solar cell are demonstrated to be improved up to 18 and 30%, respectively, compared to those of the Ge solar cell with a planar surface.

High-efficiency exfoliation of large-area mono-layer graphene oxide with controlled dimension.

In this work, we introduce a novel and facile method of exfoliating large-area, single-layer graphene oxide using a shearing stress. The shearing stress reactor consists of two concentric cylinders, where the inner cylinder rotates at controlled speed while the outer cylinder is kept stationary. We found that the formation of Taylor vortex flow with shearing stress can effectively exfoliate the graphite oxide, resulting in large-area single- or few-layer graphene oxide (GO) platelets with high yields (>90%) within 60 min of reaction time. Moreover, the lateral size of exfoliated GO sheets was readily tunable by simply controlling the rotational speed of the reactor and reaction time. Our approach for high-efficiency exfoliation of GO with controlled dimension may find its utility in numerous industrial applications including energy storage, conducting composite, electronic device, and supporting frameworks of catalyst.

Toward Green Synthesis of Graphene Oxide Using Recycled Sulfuric Acid via Couette-Taylor Flow.

Developing eco-friendly and cost-effective processes for the synthesis of graphene oxide (GO) is essential for its widespread industrial applications. In this work, we propose a green synthesis technique for GO production using recycled sulfuric acid and filter-processed oxidized natural graphite obtained from a Couette-Taylor flow reactor. The viscosity of reactant mixtures processed from Couette-Taylor flow was considerably lower (∼200 cP at 25 °C) than that of those from Hummers' method, which enabled the simple filtration process. The filtered sulfuric acid can be recycled and reused for the repetitive GO synthesis with negligible differences in the as-synthesized GO qualities. This removal of sulfuric acid has great potential in lowering the overall GO production cost as the amount of water required during the fabrication process, which takes a great portion of the total production cost, can be dramatically reduced after such acid filtration. The proposed eco-friendly GO fabrication process is expected to promote the commercial application of graphene materials into industry shortly.

Influences of animal mucins on lysozyme activity in solution and on hydroxyapatite surfaces.

The purpose of this study was to investigate the influence of animal mucins on lysozyme activity in solution and on the surface of hydroxyapatite (HA) beads. The effects of animal mucins on lysozyme activity in solution were examined by incubating porcine gastric mucin (PGM) or bovine submaxillary mucin (BSM) with hen egg-white lysozyme (HEWL) or salivary samples. HA-immobilised animal mucins or lysozyme were used to determine the influence of animal mucins on lysozyme activity on HA surfaces. Lysozyme activity was determined by turbidity measurement of a Micrococcus lysodeikticus substrate suspension. Protein concentration was determined by ninhydrin assay. PGM inhibited the activity of HEWL and salivary lysozyme in solution. The amount of inhibition was dependent on mucin concentration, incubation time and temperature, and the structural integrity of the mucin. The inhibition of salivary lysozyme activity by PGM was greater in submandibular/sublingual saliva than in parotid saliva. The inhibition of lysozyme activity by PGM was markedly dependent on pH. However, BSM did not inhibit the in-solution lysozyme activities of HEWL and clarified saliva. Both PGM and BSM bound to HA surfaces, and HA-adsorbed animal mucins increased the subsequent adsorption of lysozyme. When HA beads were exposed to a mixture of HEWL and PGM or BSM, lysozyme activity on the HA surfaces was significantly increased. The results suggest that animal mucins affect lysozyme activity, and the effects are different on HA surfaces compared with in solution. Further research is needed to determine the effect of animal mucins on lysozyme activity in vivo.

[Undifferentiated carcinoma with osteoclast-like giant cells of the pancreas].

Undifferentiated carcinoma with osteoclast-like giant cells is a rare neoplasm of exocrine pancreas. Till recently, some cases have been reported, however histogenesis of the tumors are controversial and their characteristic findings have not been described yet. Thirty five-year-old men and 75-year-old men were presented with upper abdominal pain and a palpable mass. On computed tomography, one case showed a well enhancing solid tumor with low density and the other was showed a mainly cystic tumor with peripheral enhancement in the body and tail of the pancreas. One case accompanied multiple metastatic liver masses with subhepatic lymph node enlargement. Tumor staining was seen on angiography. Biopsy and pancreatectomy were performed. Pathological findings revealed tumors composed of neoplastic spindle shaped or pleomorphic large cells with scattered non-neoplastic osteoclast-like giant cells. In one case, there were small foci of adenocarcinoma components in the periphery of the tumor. On immunohistochemical stain, neoplastic cells showed focal positivity for epithelial membrane antigen and vimentin. Tumors were diagnosed as undifferentiated carcinoma with osteoclast-like giant cells. We report these rare cases with a review of literature.

Comparative evaluation of magnetite-graphene oxide and magnetite-reduced graphene oxide composite for As(III) and As(V) removal.

Arsenic removal using Fe3O4-graphene oxide composite (M-GO) and Fe3O4-reduced graphene oxide composite (M-rGO) was investigated. The M-GO was more effective to adsorb both As(III) and As(V) than M-rGO, because the more functional groups existing on the M-GO could lead to synthesize more Fe3O4 with M-GO. As(III) was more favorable to be adsorbed than As(V) onto both M-GO and M-rGO. According to the effect of pH on arsenic removal, the electrostatic interaction between the positively charged surface of Fe3O4-graphene based adsorbents and anionic As(V) species was a major factor to adsorb As(V). The adsorption mechanism of As(III), on the other hand, was strongly affected by a surface complexation, rather than electrostatic interactions. Consequently, in terms of the process energy consumption, energy saving could be achieved via omitting the reduction process to fabricate M-rGO from M-GO and the pre-oxidation process to convert As(III) to As(V).

A Gallium Oxide-Graphene Oxide Hybrid Composite for Enhanced Photocatalytic Reaction.

Hybrid composites (HCs) made up of gallium oxide (GaO) and graphene oxide (GO) were investigated with the intent of enhancing a photocatalytic reaction under ultraviolet (UV) radiation. The material properties of both GaO and GO were preserved, even after the formation of the HCs. The incorporation of the GO into the GaO significantly enhanced the photocatalytic reaction, as indicated by the amount of methylene blue (MB) degradation. The improvements in the reaction were discussed in terms of increased surface area and the retarded recombination of generated charged carriers.

Two-Step Growth of Epitaxial InP Layers by Metal Organic Chemical Vapor Deposition.

In this study, we report experimental results on the epitaxial growth of InP layer on GaAs (001) substrate by using MOCVD. We have systematically controlled nucleation steps in order to obtain InP epitaxial layers with high crystallinity quality. The controlling parameters were flow ratio of V/IIIsources and thicknesses of nucleation layer for nucleation steps. We successfully improved the surface roughness and crystallinity of IIP epitaxial layers on GaAs substrates.

[Primary adenosquamous carcinoma of the liver: a case report].

Primary adenosquamous cell carcinoma of the liver, a variant of cholangiocarcinoma is very rare disease and its prognosis is known to be very poor. We describe here a case of primary adenosquamous carcinoma of the liver. The patient was a 60-year-old woman who complained of an eight-month history of intermittent upper abdominal pain. Abdominal computed tomography scan revealed a low density mass and intrahepatic duct stones within the dilated left intrahepatic duct in the left lateral segment. Needle biopsy of the mass was done and the histologic diagnosis was cholangiocarcinoma. Left lobectomy was then performed. Upon gross examination, there was a well defined solid mass and intrahepatic duct stone in the dilated bile duct. Microscopically, the tumor was composed of both adenocarcinoma and squamous cell carcinoma.

Anatomical confirmation of computed tomography-based diagnosis of the atherosclerosis discovered in 17th century Korean mummy.

In the present study on a newly discovered 17th century Korean mummy, computed tomography (CT) revealed multiple aortic calcifications within the aortic wall that were indicative of ancient atherosclerosis. The CT-based findings were confirmed by our subsequent post-factum dissection, which exhibited possible signs of the disease including ulcerated plaques, ruptured hemorrhages, and intimal thickening where the necrotic core was covered by the fibrous cap. These findings are strong indicators that the mummy suffered from aortic atherosclerosis during her lifetime. The present study is a good example of how CT images of vascular calcifications can be a useful diagnostic tool in forming at least preliminary diagnoses of ancient atherosclerosis.