EBSD investigation of microstructure and microtexture evolution on additively manufactured TiC-Fe based cermets-Influence of multiple laser scanning.

Sustainable TiC-Fe-based cermets have been fabricated by adopting an Additive Manufacturing route based on laser powder bed fusion technology (L-PBF). The objective is to produce crack-free cermet components by employing novel multiple laser scanning techniques with variations in laser process parameters. Electron backscatter diffraction analysis (EBSD) was used to study the microstructure and microtexture evolution with variations in laser process parameters. The investigation revealed that adjusting the preheating scan speed (PHS) and melting scan speed (MS) influenced the growth and nucleation of TiC phases. Lowering these speeds resulted in grain coarsening, while higher scan speeds led to grain refinement with larger sub-grain boundaries. Moreover, a high scanning speed increases the degree of dislocation density and internal stress in the fabricated cermet parts. Notably, it is revealed that decreasing the laser scan speed enhanced the proportion of high-angle grain boundaries in the cermet components, signifying an increase in material ductility.

In situ production of low-modulus Ti-Nb alloys by selective laser melting and their functional assessment toward orthopedic applications.

This work aimed to manufacture Ti-28.5Nb and Ti-40.0Nb (wt%) alloys in situ via selective laser melting (SLM) from Ti and Nb elemental powders. X-ray diffraction analysis revealed complete ß-phase (cubic) in Ti-40.0Nb and a mixture of (α'' orthorhombic + ß cubic) phases in Ti-28.5Nb were formed, whereas few of the Nb particles remained only partially fused during manufacturing. The fraction of partially melted Nb particles was determined as ∼2 and ∼18% in Ti-28.5Nb and Ti-40Nb, respectively. Mechanical characterization revealed higher hardness and more strength in Ti-28.5Nb than in Ti-40.0Nb due to the presence of the α'' phase in the former. Tribocorrosion tests reveal a significantly better wear-corrosion resistance for Ti-40.0Nb, as determined from a lower total volume loss in Ti-40.0Nb (∼2 × 10-4 mm-3) than in Ti-28.5Nb (∼13 × 10-2 mm-3). The lower volume loss and better corrosion resistance behavior are attributed to the ß phase, which was dominant in Ti-40.0Nb. Cell studies reveal no toxicity for up to 7 days. Both the alloys were better at supporting cell proliferation than wrought Ti6Al4V. This study presents a route to preparing Ti-Nb alloys in situ by SLM that are promising candidates for biomedical applications.

Mechanical Properties, Microstructure, and Actuation Behavior of Wire Arc Additive Manufactured Nitinol: Titanium Bimetallic Structures.

Nitinol (NiTi) is well known for its corrosion resistance, shape memory effect, superelasticity, and biocompatibility, whereas Titanium (Ti) is well known for its high specific strength, corrosion resistance, and biocompatibility. The bimetallic joint of NiTi and Ti is required for applications that require tailored properties at different locations within the same component, as well as to increase design flexibility while reducing material costs. However, because of the formation of brittle intermetallic phases, connecting NiTi and Ti is difficult. In the present study, a systematic experimental investigation is carried out to develop NiTi-Ti bimetallic joint using wire arc additive manufacturing (WAAM) for the first time and to evaluate its microstructure, mechanical properties, martensitic transformation, and actuation behavior in the as-built condition. The defect-free joint is obtained through WAAM and microstructural studies indicate the formation of intermetallics at the NiTi-Ti interface leading to higher microhardness values (600 HV). Shape recovery behavior and phase transformation temperature were also enhanced in comparison to NiTi. An improved actuation and bending angle recovery is observed in comparison with NiTi. The present study lays the way for the use of WAAM in the construction of NiTi and Ti bimetallic structures for engineering and medicinal applications.

High pressure torsion induced lowering of Young's modulus in high strength TNZT alloy for bio-implant applications.

An exceptional combination of low Young's modulus (E ~68 GPa) and high flow strength (σf ~1 GPa) was achieved for a consolidated ß-Ti-based metastable Ti-35Nb-7Zr-5Ta (TNZT) alloy subjected to room temperature high-pressure torsion (HPT). The mechanical properties of the alloy were studied by quasistatic nanoindentation tests at different strain rates, where a reduction in Young's modulus E ~73 GPa (NHPT10) and E ~68 GPa (NHPT40) is observed together with an increase in plastic deformability (or HPT rotations). The microstructure evolution with increasing shear strain has been investigated. The stabilized bcc ß-Ti phase with homogeneous nanostructure distribution was observed leading to a low Young's modulus. Severe straining causes a uniform hardness distribution without any noticeable change in the strength of the material. This study may be useful for developing excellent removable implant materials.