Aerosol jet printed, low voltage, electrolyte gated carbon nanotube ring oscillators with sub-5 µs stage delays.

A central challenge for printed electronics is to achieve high operating frequencies (short transistor switching times) at low supply biases compatible with thin film batteries. In this report, we demonstrate partially printed five-stage ring oscillators with >20 kHz operating frequencies and stage delays <5 µs at supply voltages below 3 V. The fastest ring oscillator achieved 1.2 µs delay time at 2 V supply. The inverter stages in these ring oscillators were based on ambipolar thin film transistors (TFTs) employing semiconducting, single-walled carbon nanotube (CNT) networks and a high capacitance (∼1 µF/cm(2)) ion gel electrolyte as the gate dielectric. All materials except the source and drain electrodes were aerosol jet printed. The TFTs exhibited high electron and hole mobilities (∼20 cm(2)/(V s)) and ON/OFF current ratios (up to 10(5)). Inverter switching times t were systematically characterized as a function of transistor channel length and ionic conductivity of the gel dielectric, demonstrating that both the semiconductor and the ion gel play a role in switching speed. Quantitative scaling analysis suggests that with suitable optimization low voltage, printed ion gel gated CNT inverters could operate at frequencies on the order of 1 MHz.

Printable ion-gel gate dielectrics for low-voltage polymer thin-film transistors on plastic.

An important strategy for realizing flexible electronics is to use solution-processable materials that can be directly printed and integrated into high-performance electronic components on plastic. Although examples of functional inks based on metallic, semiconducting and insulating materials have been developed, enhanced printability and performance is still a challenge. Printable high-capacitance dielectrics that serve as gate insulators in organic thin-film transistors are a particular priority. Solid polymer electrolytes (a salt dissolved in a polymer matrix) have been investigated for this purpose, but they suffer from slow polarization response, limiting transistor speed to less than 100 Hz. Here, we demonstrate that an emerging class of polymer electrolytes known as ion gels can serve as printable, high-capacitance gate insulators in organic thin-film transistors. The specific capacitance exceeds that of conventional ceramic or polymeric gate dielectrics, enabling transistor operation at low voltages with kilohertz switching frequencies.

Cell patterning on biological gels via cell spraying through a mask.

We present an easily applicable and inexpensive method for patterning cells on arbitrary surfaces including biological gels with little loss of viability or function. Single-cell suspensions of human umbilical vein endothelial cells and NIH 3T3 fibroblasts were sprayed with an off-the-shelf airbrush through a mask to create 100-microm scale patterns on collagen gels. Three-dimensional patterns were created by layering a collagen gel on top of the first pattern and patterning the top gel. Coculture of rat hepatocytes with NIH 3T3 patterns on collagen gels resulted in localized increased activity of cytochrome P-450 along the pattern. These results suggest that cell spraying is a useful tool for the study of heterotypic cellular interactions and tissue-engineering applications on biologically relevant matrices, and for the creation of three-dimensional cell patterns in vitro.

Aerosol-jet-printed, 1 volt H-bridge drive circuit on plastic with integrated electrochromic pixel.

In this report, we demonstrate a printed, flexible, and low-voltage circuit that successfully drives a polymer electrochromic (EC) pixel as large as 4 mm(2) that is printed on the same substrate. All of the key components of the drive circuitry, namely, resistors, capacitors, and transistors, were aerosol-jet-printed onto a plastic foil; metallic electrodes and interconnects were the only components prepatterned on the plastic by conventional photolithography. The large milliampere drive currents necessary to switch a 4 mm(2) EC pixel were controlled by printed electrolyte-gated transistors (EGTs) that incorporate printable ion gels for the gate insulator layers and poly(3-hexylthiophene) for the semiconductor channels. Upon application of a 1 V input pulse, the circuit switches the printed EC pixel ON (red) and OFF (blue) two times in approximately 4 s. The performance of the circuit and the behavior of the individual resistors, capacitors, EGTs, and the EC pixel are analyzed as functions of the printing parameters and operating conditions.

Two-step cell patterning on planar and complex curved surfaces by precision spraying of polymers.

Controlling adhesion of living animal cells plays a key role in biosensor fabrication, drug-testing technologies, basic biological research, and tissue engineering applications. Current techniques for cell patterning have two primary limitations: (1) they require photolithography, and (2) they are limited to patterning of planar surfaces. Here we demonstrate a simple, precision spraying method for both positive and negative patterning of planar and curved surfaces to achieve cell patterns rapidly and reproducibly. In this method, which we call precision spraying (PS), a polymer solution is aerosolized, focused with sheath airflow through an orifice, and deposited on the substrate using a deposition head to create approximately 25 microm sized features. In positive patterning, adhesive molecules, such as laminin or polyethylenimine (PEI) were patterned on polydimethylsiloxane (PDMS) substrates in a single spraying operation. A variety of animal cell types were found to adhere to the adhesive regions, and avoid the non-adhesive (bare PDMS) regions. In negative patterning, hydrophobic materials, such as polytetrafluoroethylene (PTFE) and PDMS, were patterned on glass substrates. Cells then formed patterns on the exposed glass regions and avoided the hydrophobic regions. Cellular patterns were maintained for up to 2 weeks in the presence of serum, which normally fouls non-adhesive regions. Additionally, we found that precision spraying enabled micropatterning of complex-curved surfaces. Our results show that precision spraying followed by cell plating enables rapid and flexible cellular micropatterning in two simple steps.