RESUMO
This paper presents the results of a study of radiological impacts related to the shipment of fertilisers to and from the commercial port of Ravenna (NE Italy). In particular, the effective doses to the port workers and members of the population surrounding the port area have been estimated. The study has included different types of measurement and assessment. First, the natural radioactivity of different fertilisers moving through the port has been determined: (40)K, (226)Ra, (210)Pb, (228)Ra and (228)Th concentrations have been analysed using γ-ray spectrometry, while (238)U and (232)Th concentrations have been determined by ICP-MS. At the same time, a dose rate meter and electret ion chambers were used to measure the external irradiation and the radon concentrations, respectively. Then, air pollutant dispersion models have been applied in order to assess particulate matter concentration in the port site and the surrounding residential areas, and consequently the inhalation doses. Finally, the annual effective doses to workers and local residents have been estimated. The effective doses to workers and the population have been estimated to be 0.9 mSv yr(-1) and 0.07 µSv yr(-1), respectively.
Assuntos
Comércio , Fertilizantes/efeitos adversos , Exposição Ocupacional/efeitos adversos , Radiação , Humanos , ItáliaRESUMO
Odor pollution is the biggest source of complaints from citizens concerning environmental issues after noise. Often, the need for corrective actions is evaluated through simulations performed with atmospheric dispersion models. To save resources, air pollution control institutions perform a first-level odor impact assessment, for screening purposes. This is often based on Gaussian dispersion models (GDM), which does not need high computational power. However, their outputs tend to be conservative regarding the analyzed situation, rather than representative of the real in-site conditions. Hence, regulations and guidelines adopted at an institutional level for authorization/control purposes are based on Lagrangian particle dispersion models (LPDM). These models grant a more accurate simulation of the pollutants' dispersion even if they are more demanding regarding both technical skills and computing power. The present study aims to increase the accuracy of screening odor impact assessment by identifying the correlation function of the outputs derived from the two simulation models. The case study is placed in northern Italy, where a single-point source, with various stack heights, was considered. The case study is placed in northern Italy, where a single-point source, with various stack heights, was considered. The obtained correlation functions allow the practitioner to have a more accurate first-level odor impact assessment, to save time for training, and to reduce the site-specific meteorological data before proceeding with the simulation. The identified functions could allow institutions to estimate the results that would have been forecasted with the application of the more complex LPDM, applying, however, the much simpler GDM. This solution grants an accurate tool which can be used to address citizens' concerns while saving workforce and technical resources. Limitations are related to the specificity of the method regarding type sources, orography, and meteorological conditions. Comparison with other screening tools is also presented and discussed.
RESUMO
Carbon dots (CDs) are promising photothermal nanoparticles that can be utilized in environmental treatments. They exhibit favorable physicochemical properties, including low toxicity, physical and chemical stability, photo-dependant reversible behaviour, and environmentally friendly synthesis using benign building blocks. Here, we synthesized innovative CDs/polylactic acid (PLA) electrospun composite membranes for evaluating the removal of hydrophobic compounds like long-chain hydrocarbons or oils in biphasic mixtures with water. The ultimate goal was to develop innovative and sustainable solar-heated oil absorbents. Specifically, we fabricated PLA membranes with varying CD contents, characterized their morphology, thermal, and mechanical properties, and assessed the environmental impact of membrane production according to ISO 14040 and 14044 standards in a preliminary "cradle-to-gate" life cycle assessment study. Solar radiation experiments demonstrated that the CDs/PLA composites exhibited greater uptake of hydrophobic compounds compared to pure PLA membranes, ascribable to the CDs-induced photothermal effect. The adsorption and regeneration capacity of the new CDs/PLA membrane was demonstrated through multiple uptake/release cycles. Ecotoxicity analyses confirmed the safety profile of the new adsorbent system towards freshwater microalgae, further emphasizing its potential as an environmentally friendly solution for the removal of hydrophobic compounds in water treatment processes.
RESUMO
The use of sustainable and natural materials is an ever-increasing trend in cosmetic. Natural calcium phosphate (CaP-N) from food by-products and especially from fisheries (i.e., bones), has been suggested as a sustainable option to chemicals commonly used in cosmetic products, in particular to UV-filters in sunscreens. However, the environmental benefits and impacts of its production and use are still uncertain as they have never been quantified. In this paper, we report on toxicological characterization of CaP-N produced from incineration of fish meal in a pilot scale plant. Furthermore, we quantified the environmental burdens linked to the partial substitution of UV-filters by CaP-N through the life cycle assessment (LCA) comparing CaP-N with zinc oxide nanoparticles (ZnO NPs) as alternative option. CaP-N consists in a biphasic mixture 53:47 of hydroxyapatite:ß-tricalcium phosphate, and is made of round particles with a diameter in the range of a few microns. Toxicity tests on 4 aquatic species (Dunaliella tertiolecta, Tigriopus fulvus, Corophium insidiosum and Gammarus aequicauda) revealed that CaP-N does not produce any adverse effect, all the species showing EC/LC50 values higher than 100 mg L-1. Moreover, during the 96 h acute toxicity test on C. insidiosum, which is a tube-building species, the specimens built their tubes with the available CaP-N, further attesting the non-toxicity of the material. The LCA study showed that the environmental performance of CaP-N is better than that of ZnO NPs for 11 out of 16 impact categories analysed in this study, especially for the categories Ecotoxicity and Eutrophication of freshwaters (an order of magnitude lower), and with the exception of fossil resources for which CaP-N has a significantly higher impact than ZnO NPs (+140 %). Concluding, our study demonstrates that the replacement of ZnO NPs with CaP-N thermally extracted from fish bones in cosmetic products can increase their safety and sustainability.
Assuntos
Cosméticos , Nanopartículas , Óxido de Zinco , Animais , Protetores Solares/toxicidade , Protetores Solares/química , Óxido de Zinco/toxicidade , Óxido de Zinco/química , Nanopartículas/toxicidade , Fosfatos de CálcioRESUMO
The ability of microalgae to sequester carbon and at the same time synthesise valuable compounds with potential applications in nutraceutical, pharmaceutical and cosmetic industries makes them attractive for commercial deployment, especially in view of a blue bioeconomy. Among microalgae, the diatom Phaeodactylum tricornutum is considered as an important potential source of omega-3 polyunsaturated fatty acids, such as eicosapentanoic acid, an essential polyunsaturated fatty acid with anti-inflammatory and antimicrobial properties. The aim of this study was to perform the Life Cycle Assessment of the cultivation of P. tricornutum - at semi-industrial scale in photobioreactor - for the production of high-quality bioactive compounds comparing synthetic carbon dioxide supply to a supply with waste carbon dioxide from a biogas upgrading process hypothesizing industrial symbiosis network. The effect of renewable energy use instead of the European electricity mix was also examined. Primary data on the production process, including the stages of cleaning and sterilisation, cultivation, harvesting and freeze-drying, were used. The midpoint impact categories recommended in the ILCD Handbook were used for performing the impact assessment. A sensitivity analysis was also performed on algal productivity, culture medium recirculation factor and amount of solvents per cleaning cycle. Firstly, results indicate in general cultivation and freeze-drying as the most contributing stages to the impacts. Secondly, they demonstrate in the comparative assessment that the use of carbon dioxide from the biogas upgrading is a feasible and attractive alternative to the synthetic one, as it allows for the improvement of the environmental performance of the production process in all the analysed impact categories. Finally, sensitivity analysis suggests that the environmental performance could be further improved by acting on other key factors, such as electricity source, nutrients culture medium and cleaning solutions.
Assuntos
Diatomáceas , Microalgas , Biocombustíveis , Biomassa , Dióxido de Carbono , FotobiorreatoresRESUMO
Recently, wood pellets have become a reliable and clean renewable fuel for residential heating, replacing fossil fuels and reducing greenhouse gas emissions. Wood pellets are normally produced in industrial pellet plants (centralised production), but decentralised small-scale local production also occurs. This study applies Life Cycle Assessment (LCA) to quantify and compare the environmental profile of one centralised and two decentralised alternatives for wood pellet production for residential heating in Portugal: (1) industrial wood pellets production (centralised), (2) wood pellets production at sawmills (decentralised) and (3) wood pellets production at households (decentralised). System boundaries include the stages of forest management, wood pellet production, wood pellet distribution and wood pellet energetic conversion. The impact results show that industrial pellet production ranks as the worst alternative, while pellet production at households has the best environmental profile for all the impact categories under study. However, the environmental impacts of pellet production at the sawmill do not differ greatly from those of the pellet production at households; they are 14 to 16% higher for global warming and fossil resources scarcity and 0.3 to 3% higher for the remaining impact categories. The worst environmental performance of the industrial pellet production alternative is mainly due to high electricity and diesel consumption during wood pellet production and the use of logging residues to generate heat for drying biomass feedstock. A sensitivity analysis was performed to evaluate the influence of changing the distance travelled during the transport of packed pellets to stores and sawdust to households. The results show changes in the environmental performance ranking, highlighting that for short distances, both decentralised alternatives can be more sustainable from an environmental perspective than the centralised alternative, but for larger distances, the pellet production at households should be avoided.
RESUMO
The vertical distribution of PCBs was measured in a dated core from the continental shelf of the Korea Strait. The historical trend of deposition and fluxes of individual and total PCB agreed well with the dynamics of historical tendencies of PCBs consumption in South Korea up to mid-1980 and a peak of total PCBs of 810â¯ngâ¯kg-1 was recorded at the turn of the 1960s. A second period of deposition, when concentrations of total PCB up to 1007â¯ngâ¯kg-1 were reached, was evidenced between 1989 and 2010 after the ban of PCBs. Sediments deposited in 1990s-2010, and sediments deposited in the period of maximum PCBs use (1956-1983) are both enriched in the less chlorinated homologue groups (tri- and tetrachlorobyphenyls) and congener PCB 118. However, the ratio of dioxin-like PCBs, and dichloro- and hexachloro homologue groups disclosed compositional variations between the two time periods. Source analysis suggested that PCBs in the sediment record mainly originated from Kanechlor 300, Kanechlor 400 and Aroclor 1242 technical mixtures overlapped by secondary/unintentional combustion sources from regional steel making processes in the last decades (1990s-2010).
Assuntos
Sedimentos Geológicos/análise , Bifenilos Policlorados/análise , Poluentes Químicos da Água/análise , Monitoramento Ambiental , História do Século XX , História do Século XXI , Instalações Industriais e de Manufatura/história , Bifenilos Policlorados/história , República da Coreia , Aço/históriaRESUMO
Pesticides are commonly applied in conventional agricultural systems, but they can lead to serious environmental contamination. The calculation of on-field pesticide emissions in Life Cycle Assessment (LCA) studies is challenging, because of the difficulty in the calculation of the fate of pesticides and, therefore, several literature approaches based on different dispersion models have been developed. PestLCI 2.0 model can provide simultaneous assessment of the emission fractions of a pesticide to air, surface water and groundwater based on many parameters. The goal of this study is to exploit the extent of PestLCI 2.0 sensitivity to soil variations, with the ultimate goal of increasing the robustness of the modelling of pesticide emissions in LCA studies. The model was applied to maize cultivation in an experimental farm in Northern Italy, considering three tests, which evaluated the distribution of pesticides among environmental compartments obtained considering different soil types. Results show that small variations in soil characteristics lead to great variation of PestLCI 2.0, with a significance that depends on the type of environmental compartment. The compartment most affected by soil variations was groundwater, whereas surface waters were dominated by meteorological conditions, pesticides' physical and chemical properties and wind drift, which are independent from soil characteristics. Therefore, the use of specific soil data in PestLCI 2.0 results in the availability of a comprehensive set of emission data in the different compartments, which represents a relevant input for the inventory phase of LCA studies and can increase their robustness. Nevertheless, PestLCI 2.0 requires a great effort for the data collection and a specific expertise in soil science for interpreting the results. Moreover, characterization factors for pesticide groundwater emissions should be developed, in order to exploit these detailed results in the impact assessment phase, Finally, the study provides further insights into future improvement of PestLCI 2.0.
RESUMO
A life cycle thinking approach focusing on energy and greenhouse gas savings has been applied to study the potential for energy recovery and organic matter reclamation from Waste Activated Sludge produced in Waste Water Treatment Plants by means of a catalytic thermo-chemical process. A generic Basic Sludge Processing line has been modelled following common waste water and sludge treatment stages found in several European plants. This has served to identify and divide generic sludge treatment units in order to compare the performance of different industrial configurations where a specific thermo-chemical technology treatment unit and related cogeneration was substituted or added to reference units. The considered technology is an enhanced intermediate pyrolysis screw reactor combined with a reforming process known as Thermo-Catalytic Reforming allowing for conversion of sewage sludge into energy carriers and reclamation of organic substances in the form of charcoal (biochar). In order to study the greenhouse gas savings, a calculator tool complying with Directive 2009/28/EC has been adopted. Results show that substantial benefits in terms of energy production and greenhouse gas emissions reduction of a sludge-to-energy system are expected if the secondary sludge is directly treated with the Thermo-Catalytic Reforming process, without an intermediate anaerobic digestion step.
Assuntos
Gases de Efeito Estufa , Esgotos , Parafusos Ósseos , Pirólise , Eliminação de Resíduos Líquidos , Águas ResiduáriasRESUMO
Forty-two samples of building materials commonly used in Italian dwellings were surveyed for natural radioactivity. External (gamma), as defined and used by the European Commission, and internal (alpha) hazard indexes were calculated and radon specific exhalation rate and emanation fraction were measured. The accumulation method, by using the E-PERM electret ion chambers, was employed to determine specific exhalation rates of 222Rn. Several of the materials had hazard indexes that exceeded the European Commission limit values. However, it was evident that limit values for internal hazard indexes set based on Rn emanation should take into account the properties and use of the materials. For example, Rn emanation from basalt and glazed tiles was substantially lower than the Rn emanation from other materials with similar hazard indexes. Clearly there is need for improved guidelines and regulations in this area.
Assuntos
Radiação de Fundo , Radônio/análise , ItáliaRESUMO
A Life Cycle Assessment is conducted on pyrolysis coupled to anaerobic digestion to treat corn stovers and to obtain bioenergy and biochar. The analysis takes into account the feedstock treatment process, the fate of products and the indirect effects due to crop residue removal. The biochar is considered to be used as solid fuel for coal power plants or as soil conditioner. All results are compared with a corresponding fossil-fuel-based scenario. It is shown that the proposed system always enables relevant primary energy savings of non-renewable sources and a strong reduction of greenhouse gases emissions without worsening the abiotic resources depletion. Conversely, the study points out that the use of corn stovers for mulch is critical when considering acidification and eutrophication impacts. Therefore, removal of corn stovers from the fields must be planned carefully.
Assuntos
Carvão Vegetal , Meio Ambiente , Lignina , Eliminação de Resíduos/métodos , Zea mays , Anaerobiose , Biocombustíveis , Biomassa , Biotecnologia/métodos , Carvão Vegetal/química , Carvão Mineral , Lignina/química , Centrais Elétricas , Solo , Zea mays/químicaRESUMO
A calculation model for determining the indoor dose due to building materials with significant concentration of radioactivity has been applied to the case study of ceramic tiles; the model allows the contribution of bearing walls and wall covering materials to be calculated. The model is implemented in FORTRAN 77 and provides a quantification of the gamma radiation field (in terms of external dose rate in air, nGyh-1) inside a room with known dimensions. Application model results have been validated both by comparison with the results obtained by other authors and by experimental measurements. Model sensitivity and performances have been analysed and lastly the case studies focused on ceramic tiles have been proposed.
Assuntos
Poluição do Ar em Ambientes Fechados/análise , Contaminação Radioativa do Ar/análise , Cerâmica/análise , Materiais de Construção/análise , Raios gama , Radiometria/métodos , Tório/análise , Algoritmos , Doses de Radiação , Monitoramento de Radiação/métodos , SoftwareRESUMO
The aim of the first part of this investigation is to assess the radioactive pollution caused by a production plant of complex fertilizers (that is to say containing nitrogen, phosphorus and, in some cases, potassium). Firstly, the authors determine the concentrations of natural radioactivity present in raw materials, end products and wastes of the industrial plant. Then, they carry out an assessment of radioactive releases into the atmosphere, hydrosphere and lithosphere as well as of their significance from the environmental point of view. The second part of the investigation will be aimed at assessing the annual effective doses to plant workers and to members of the population surrounding the industrial site.
Assuntos
Fertilizantes , Resíduos Industriais/análise , Poluentes Radioativos/análise , Resíduos Radioativos/análise , Radioisótopos/análise , Meio Ambiente , Humanos , Itália , Nitrogênio , Fosfatos , Potássio , Monitoramento de Radiação , Espectrometria gama , Eliminação de Resíduos LíquidosRESUMO
In the previous paper the authors have studied the radioactive pollution caused by a complex fertilizers production plant. In this paper, the effective doses to the plant workers and to members of the population surrounding the industrial site are estimated. The authors have considered external irradiation, inhalation and ingestion of dust and inhalation of radon and radon daughters as the main occupational exposure routes. After estimating the single contributions, the total effective dose has been calculated as the sum of said contributions. Calculations have been differentiated according to the different tasks of the company employees. The estimated annual effective doses range from 0.6 to 1.4 mSv y(-1). Annual individual effective doses to local residents, resulting from internal and external irradiation caused by particulate matter emitted into the atmosphere by the plant have been estimated. The maximum individual dose rate is estimated to be about 4 microSv y(-1).
Assuntos
Poluentes Radioativos do Ar/análise , Poluição do Ar em Ambientes Fechados/análise , Exposição Ambiental , Fertilizantes , Exposição Ocupacional , Radioisótopos/análise , Poeira/análise , Humanos , Nitrogênio , Fosfatos , Potássio , Doses de Radiação , Monitoramento de Radiação , Radônio/análiseRESUMO
The paper presents the results of a study on radiological impacts resulting from a zircon sand processing plant located in the North-Eastern part of Italy. Activity concentrations of radionuclides found in materials associated with this industrial process are presented as well as the results of the assessment of the annual effective doses to the workers and the members of the public. Gamma-spectrometric analyses were performed on "raw" sands, end-products, and soils sampled near the plant. Thermoluminescent dosimeters, electric pumps and electret ion chambers were used to measure the external irradiation, the indoor dust concentrations and the radon concentrations, respectively. The ground-level air concentration of radioactive particulate near the plant and the deposition of particulate matter were estimated by a Gaussian model (ISCLT3). Finally, the annual effective doses, calculated as provided for by Directive 96/29/Euratom, were estimated to be 1.7 mSv y(-1) for workers and 4.4 microSv y(-1) for members of the public.
Assuntos
Exposição Ocupacional , Radioisótopos de Potássio/análise , Radônio/análise , Tório/análise , Urânio/análise , Poluentes Radioativos do Ar/análise , Poluição do Ar em Ambientes Fechados/análise , Poeira/análise , Exposição Ambiental , Humanos , Modelos Teóricos , Tamanho da Partícula , Doses de Radiação , Silicatos , Dióxido de Silício , Poluentes Radioativos do Solo/análise , Vento , ZircônioRESUMO
The Life Cycle Assessment (LCA) methodology is widely applied in several industrial sectors to evaluate the environmental performance of processes, products and services. Recently, several reports and studies have emphasized the importance of LCA in the field of engineered nanomaterials. However, to date only a few LCA studies on nanotechnology have been carried out, and fewer still have assessed aspects relating to ecotoxicity. This is mainly due to the lack of knowledge in relation on human and environmental exposure and effect of engineered nanoparticles (ENPs). This bottleneck is continued when performing Life Cycle Impact Assessment, where characterization models and consequently characterization factors (CFs) for ENPs are missing. This paper aims to provide the freshwater ecotoxicity CF for titanium dioxide nanoparticles (nano-TiO2). The USEtox model has been selected as a characterisation model. An adjusted multimedia fate model has been developed which accounts for nano-specific fate process descriptors (i.e. sedimentation, aggregation with suspended particle matter, etc.) to estimate the fate of nano-TiO2 in freshwater. A literature survey of toxicity tests performed on freshwater organism representative of multiple trophic levels was conducted, including algae, crustaceans and fish in order to collect relevant EC50 values. Then, the toxic effect of nano-TiO2 was computed on the basis of the HC50 value. Thus, following the principle of USEtox model and accounting for nano-specific descriptors a CF for the toxic impact of freshwater ecotoxicity of 0.28 PAFdaym(3)kg(-1) is proposed.
Assuntos
Nanopartículas Metálicas/toxicidade , Titânio/toxicidade , Poluentes Químicos da Água/toxicidade , Testes de ToxicidadeRESUMO
Recent studies suggest that the ecotoxicity of engineered nanoparticles (ENPs) is dependent upon the treatment of ENPs in suspensions (e.g. sonication or use of solvents) and on the mode of exposure to test organisms. We conducted several bioassays with Daphnia magna in order to determine how adverse effects of TiO2 nanoparticles (n-TiO2) are influenced by experimental set-up. Several treatments were applied, including three test media, several treatments of n-TiO2 suspensions (stirring, sonication) and different exposure modes (exposure duration and volume of test suspension). No adverse effects were observed when D. magna were exposed to 50 mL of suspension, regardless of TiO2 concentration (up to 250 mg/L) and exposure duration. Conversely, adverse effects were observed when D. magna were exposed to 2 mL of suspension for 96 h with a 50 % effect concentration EC50 values ranging from 32 mg/L to 82 mg/L. Test media had no significant influence on the outcome of all treatments. For a better mechanistic understanding of the experimental set-up at which adverse effects were observed, the particle size of n-TiO2 in the test media was characterized throughout the test duration. These measurements revealed a fast and strong agglomeration with a secondary particle size in the order of magnitude of micrometers. Our study describes how the effects of n-TiO2 on D .magna are influenced by the duration of exposure and volume of media, highlighting the need for standardization of experimental methods.
Assuntos
Daphnia/efeitos dos fármacos , Monitoramento Ambiental/métodos , Nanopartículas/toxicidade , Titânio/toxicidade , Poluentes Químicos da Água/toxicidade , Animais , Relação Dose-Resposta a Droga , Ecotoxicologia , Monitoramento Ambiental/normas , Tamanho da Partícula , Suspensões , Fatores de Tempo , Testes de Toxicidade AgudaRESUMO
The distribution and the origin of carbon and nitrogen in sediments of an Italian lagoon--located north-east of Ravenna town--were investigated. From 1957 to 1976, the lagoon had been affected by a strong industrial pollution due to an important petrochemical complex. At present, industrial and domestic waste waters undergo a treatment process before being discharged into the lagoon. Sediment samples from 10 locations throughout the lagoon were analysed, in order to document the spatial and vertical distribution of C and N. Data show a very strong variability (organic carbon content varies between 8.9% and 0.14%) and the highest values were found in the immediate vicinity of the industrial discharge. Sediment organic matter shows allochthonous origin in proximity of industrial discharge and autochthonous origin in the remaining areas.
Assuntos
Carbono/análise , Sedimentos Geológicos/química , Nitrogênio/análise , Poluentes do Solo/análise , Poluentes Químicos da Água/análise , Itália , Água do Mar , Movimentos da ÁguaRESUMO
In this paper the authors propose a framework for combining life cycle assessment (LCA) and Risk Assessment (RA) to support the sustainability assessment of emerging technologies. This proposal includes four steps of analysis: technological system definition; data collection; risk evaluation and impacts quantification; results interpretation. This scheme has been applied to a case study of nanofluid alumina production in two different pilot lines, "single-stage" and "two-stage". The study has been developed in the NanoHex project (enhanced nano-fluid heat exchange). Goals of the study were analyzing the hotspots and highlighting possible trade-off between the results of LCA, which identifies the processes having the best environmental performance, and the results of RA, which identifies the scenarios having the highest risk for workers. Indeed, due to lack of data about exposure limits, exposure-dose relationships and toxicity of alumina nanopowders (NPs) and nanofluids (NF), the workplace exposure has been evaluated by means of qualitative risk assessment, using Stoffenmanager Nano. Though having different aims, LCA and RA have a complementary role in the description of impacts of products/substances/technologies. Their combined use can overcome limits of each of them and allows a wider vision of the problems to better support the decision making process.